2AOHHTURBOXC610Turbox C610 SOM

Thundercomm TurboX C610 SOM DATASHEET Rev V1.0 Oct 12, 2020 Empowering Every IoT Device with Our Technology TurboX C610 SOM DATASHEET Copyright© 2020 Thundercomm Technology Co., Ltd. All rights reserved. Revision History Revision Date Description 1.0 Oct 12，2020 Initial release Applications TurboX C610 SOM is ideal for many applications including (but not limited to): AI, Robotics, Virtual Reality (VR), Augmented Reality (AR), Drones and Medical Devices. Reference Documents Document 80-pl052-1_a_qcs610_qcs410_data_sheet 80-pl052-41_b_qcs610_qcs410_+_pm6150_+_pm6150l_reference_schematic 80-ph856-1_j_pm6150_pm6250_pm7150_power_management_ic_device_specification 80-pg281-1_k_pm6150a_pm6150l_and_pm7150a_pm7150l_device_specification 80-ph856-5a_g_pm6150_pm6250_pm7150_power_management_ic_design_guidelines_training_slides 80-wl022-1_j_wcn3980_wireless_connectivity_ic_device_specification Intellectual Property Statement This document itself and the proprietary technical information contained herein is the property of Thundercomm. Without prior written authority of Thundercomm, no one shall copy, modify or reprint the whole or part of this document. Offenders are liable for all related damages, loss and litigations. Thundercomm reserves the right to modify this document without notice at any time. Trademarks Hexagon is a trademark of Qualcomm Technologies, Inc. and/or its affiliated companies. Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere. All other trademarks are the property of their respective owners. TurboX C610 SOM DATASHEET Copyright© 2020 Thundercomm Technology Co., Ltd. All rights reserved. Table of Contents TurboX C610 System on Module ............................................................................................ 1 Description ..................................................................................................................................... 1 Features .......................................................................................................................................... 1 1 Physical Description .................................................................................................................. 3 1.1 Hardware Block Diagram .......................................................................................................................................... 3 1.2 Major Components Location ................................................................................................................................... 3 1.3 Package Drawing and Dimensions ........................................................................................................................ 5 2 Interfaces Description ............................................................................................................... 5 2.1 Interfaces Parameter Definitions ........................................................................................................................... 5 2.2 Pin Description ............................................................................................................................................................. 7 2.3 Pin Assignment............................................................................................................................................................. 8 3 Function Description ...............................................................................................................18 3.1 Input Power Management ..................................................................................................................................... 18 3.2 Charger Module ......................................................................................................................................................... 18 3.3 Power on Sequence .................................................................................................................................................. 18 3.4 C610 System Power Tree ........................................................................................................................................ 19 3.5 C610 Power On........................................................................................................................................................... 19 3.6 C610 Boot Configuration ........................................................................................................................................ 20 3.7 C610 USB Ports........................................................................................................................................................... 20 3.8 Debug UART ................................................................................................................................................................ 21 4 Electrical Characteristics .........................................................................................................22 4.1 Operating Conditions .............................................................................................................................................. 22 4.2 Output Power.............................................................................................................................................................. 22 4.3 Digital-logic characteristics .................................................................................................................................... 23 4.4 USB ................................................................................................................................................................................. 23 4.5 I2S ................................................................................................................................................................................... 23 4.6 I2C .............................................…

Text truncated - open the document above for the full version.

Thundercomm Technology Co., Ltd Address: Building 4, No. 99, Data Valley Middle Road, Xiantao District, Yubei District, Chongqing, China Tel.: +86 010-82036511 Fax: +86 010-82036511 E-mail: [email protected] FCC Confidential Authorization Date: 2020-09-29 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AOHHTURBOXC610 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Thundercomm Technology Co., Ltd, hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Qiyong Zhou Manager

Thundercomm Technology Co.,Ltd Address: Building 4, No. 99, Data Valley Middle Road, Xiantao District, Yubei District, Chongqing, China Tel.:+86 010-82036511 Fax: +86 010-82036511 E-mail:[email protected] Modular Approval Letter Date: 2021-02-10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Application Examiner, We, Thundercomm Technology Co., Ltd is submitting this application for certification of product named as TurboX C610 SOM, Model Numbers: TurboX C610 (FCC ID: 2AOHHTURBOXC610). It is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below: 1. “The modular transmitter must have its own RF shielding.” Yes, it is fulfilled. The radio portion of the module has its own RF shielding. The shielding is installed at the factory. Please see the EUT photos. 2. “The modular transmitter must have buffered modulation/data inputs.” Yes, it is fulfilled. The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over modulation. Please see the Schematics exhibit. 3. “The modular transmitter must have its own power supply regulation.” Yes, it is fulfilled. The EUT has its own power supply regulation to insure compliance. 4. “The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c).” Yes. The EUT has a PIFA antenna design. 5. “The modular transmitter must be tested in a stand-alone configuration.” Yes, it is fulfilled. The EUT was tested in a stand-alone configuration. 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes, it is fulfilled. The module will be labeled with its own FCC ID number. Please see FCC ID label & location exhibit. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” Yes, it is fulfilled. The necessary explanation to be complied with this requirement is contained in the user manual, and please refer to the User manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” Yes, the module is intended to use in distance more that 20cm. FCC RF exposure requirement satisfied with 47CFR §2.1091. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. Sincerely Yours, Signature: Qiyong Zhou Title: Manager

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF EXHIBIT B – EUT PHOTOGRAPHS EUT on test jig Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF EXHIBIT B – EUT PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-RF Antenna

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. BACL is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15B, CLASS B TEST REPORT For Thundercomm Technology Co., Ltd Building 4, No. 99, Data Valley Middle Road, Xiantao District, Yubei District, Chongqing FCC ID: 2AOHHTURBOXC610 Report Type: Original Report Product Type: TurboX C610 SOM Re port Number: RSZ200929002-00A Re port Date: 2020-10-27 Reviewed B y: Jacob Kong RF En gineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200929002-00A FCC Part 15B, Class B Page 2 of 16 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 SPECIAL ACCESSORIES ................................................................................................................................................. 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 EQUIPMENT LIST ...................................................................................................................................................... 8 FCC §15.107 – AC LINE CONDUCTED EMISSIONS ............................................................................................. 9 APPLICABLE STANDARD .............................................................................................................................................. 9 EUT SETUP .................................................................................................................................................................. 9 EMI TEST RECEIVER SETUP ......................................................................................................................................... 9 TEST PROCEDURE ........................................................................................................................................................ 9 CORRECTED FACTOR & MARGIN CALCULATION ....................................................................................................... 10 TEST DATA ................................................................................................................................................................ 10 FCC §15.109 - RADIATED SPURIOUS EMISSIONS ............................................................................................ 13 APPLICABLE STANDARD ............................................................................................................................................ 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 14 TEST PROCEDURE ...................................................................................................................................................... 14 CORRECTED AMPLITUDE & MARGIN CALCULATION ...…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200929002- 00A EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200929002- 00A Radiated Emissions – Front View (Below 1 GHz) Radiated Emissions – Rear View (Below 1 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: RSZ200929002- 00A Radiated Emissions – Front View (Above 1 GHz) Radiated Emissions – Rear View (Above 1 GHz)