2APA9-IPC025BIMILAB EC3 Outdoor Security Camera

Connecting to Mi Home App This product works with Mi Home and can be controlled using the Mi Home app. Scan the QR code to download and install the Mi Home app. If you already have Mi Home app installed, you will be directed to the device connection page. You can also search for "Mi Home" in an app store to download and install the Mi Home app. 2. Insert four plastic expansion nuts into the holes. The camera has a power supply port and a LAN port. Waterproofing must be done on both these ports. 1. Wrap the power supply port with the waterproofing tape as shown below. 2. Wrap the LAN port with the waterproofing tape or a waterproofing sleeve. The LAN port can be wrapped with the waterproofing tape in the same way as the power supply port. For instructions on the use of a waterproofing sleeve, visit the IMiLab WeChat account. Waterproofing kit 3. Cover part of 2-in-1 power and LAN cable with the base plate as indicated. Note: In order to prevent accidents and injuries, please secure the device firmly onto the wall as illustrated. The wall on which the device is mounted must have a loading capacity of at least 3 times the weight of the device. Do not install the device near a heat source, such as an air-conditioner compressor, air vent of a range hood or air vent of a gas water heater. As the camera can be rotated horizontally, please pay attention to the safe turning distance during installation. Do not install the device at a location where its horizontal movement would be impeded. 4. Put the base plate on the wall. Ensure that the 2-in-1 power and LAN cable goes straight down. Secure the base plate by inserting the screws into the expansion nuts. Restoring factory settings Press and hold the reset button to restore the factory settings. The content inside the micro SD card will not be deleted. Note: When inserting or removing the micro SD card, please disconnect the camera from the power supply. Please use a micro SD card from a reputable manufacturer. The recommended read and write speed of the micro SD card is at least U1/Class 10. Connecting the Device Turn on the camera Step 1: Insert the power supply cable into the camera's power supply port. Connect the other end of the power supply cable to a power source. Step 2: When connected to a power supply, the indicator light will show the camera's status. When the indicator light is yellow, the camera is being turned on; when the indicator light is flashing yellow, it is waiting to be connected. Insert a micro SD card Ensure that the camera is disconnected from the power supply. Use a screwdriver to remove the protective case and expose the micro SD card slot. The contact points of the micro SD card should be facing the same direction as the camera. Insert the micro SD card into the slot. Note: The actual operation may differ from the instructions above due to Mi Home app upgrades and updates. Please follow the instructions shown by the Mi Home app. Video Playback Past videos can only be viewed when a compatible micro SD card is inserted in IMiLab EC3 Outdoor Security Camera. After inserting a micro SD card and turning on the device, the camera will automatically start recording. In the control interface for . in the Mi Home app, tap the playback button to enter the video playback page. You can also view a recording by selected a time period.. IMiLab Smart Camera Outdoor... 12MB / s 06:20 Sharing a Video In the control interface for IMiLab EC3 Outdoor Security Camera in the Mi Home app, you can set the device as a shared device in the settings menu and invite others to watch the recordings. Users must download the Mi Home app and login to their Xiaomi account in order to view the recordings of the shared device. Share group Check for firmware updates Rename IMiLab Smart Camera... Security settings Share device Remove device Add Home screen shortcut Feedback Network info Share with Mi Account Share manage Share...General settings Infrared Night Vision The light sensor can automatically switch the device to night vision mode through IR-CUT based on changes in the lighting of the environment. The device features 10 built-in infrared night vision lights that ensure recording stays clear even in darkness. Infrared night vision effect illustration 2019 3 2 20:51:05 About Works with Mi Home A product that works with Mi Home can be controlled using the Mi Home app. Please note that such products are only verified at the software level. Xiaomi and Mi Home are not responsible for the production, implementation of standards and quality control of these products and their manufacturers. The working temperature of the device is -20°C to 60°C. Do not use the device when the temperature is too high or too low. For better results, avoid placing the camera in front of or next or a glass surface, a white-colored wall or other reflective surfaces as this may cause the recording to have un-even lighting between the foreground and background or be over-exposed. Please ensure that the device is within Wi-Fi signal coverage. Place it at a location with good Wi-Fi signal strength. Try to avoid placing the device near a metallic object, a microwave oven or other objects that may cause signal interference. Home SecurityPrecautions Correct Disposal of this product. This marking indicates that product should not be disposal with other household wastes through out the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling. WEEE Disposal and Recycling Information For pluggable equipment, the socket-outlet (power adaptor) shall be installed near the equipment and shall be easily accessible. Hereby, Shanghai Imilab Technology Co., Ltd. declares tha…

Text truncated - open the document above for the full version.

QA-FR-170-B Company: Shanghai Imilab Technology co.,LTD Add: Room908,No.1,Lane399,Shengxia Rd.,China Pilot Free Trade Zone,Shanghai,China Tel: 021-61890898 Fax: 021-64088898 FCC Authorization Date: 2020-01-19 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Shanghai Imilab Technology co.,LTD, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Typed or Printed Name: hesong wang Title: Manager

Company Name: Shanghai Imilab Technology co.,LTD Add: Room908,No.1,Lane399,Shengxia Rd.,China Pilot Free Trade Zone,Shanghai,China Tel: 021-61890898 Fax: 021-64088898 E-mail: [email protected] FCC Confidential Authorization Date:2020-01-19 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2APA9-IPC025B To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Shanghai Imilab Technology co.,LTD hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Typed or Printed Name: hesong wang Title: Manager

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS ANT1 Port ANT2 Port Antenna

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RKSA200119001-00B FCC Part 15.247 Page 17 of 99 FCC §1.1310 & §2.1091 –MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart §2.1091 and subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f²) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculated Formulary: Predication of MPE limit at a given distance S = PG/4πR² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RKSA200119001-00B FCC Part 15.247 Page 18 of 99 Calculated Data: Mode Frequency Range (MHz) ANT1 Gain Tune up Conducted Power Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric)(dBm)(mW) 802.11b 2412~2462 1.0 1.26 16.0039.8120 0.0100 1.0 802.11g 1.0 1.26 16.0039.8120 0.0100 1.0 802.11 n-HT20 1.0 1.26 19.0079.4320 0.0199 1.0 802.11 n-HT40 2422~2452 1.0 1.26 18.5070.7920 0.0177 1.0 Note: The tune up conducted power was declared by the manufacturer. Conclusion: The device meets MPE at distance 20cm.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15.247 TEST REPORT For Shanghai Imilab Technology Co.,Ltd. Room 908, No. 1, Lane 399, Shengxia Rd., China Pilot Free Trade Zone, Shanghai, China FCC ID: 2APA9-IPC025B Report Type: Original Report Product Type: IMILAB EC3 Outdoor Security Camera Test Engineer: Chao Gao Re port Number: RKSA200119001-00B Re port Date: 2020-03-05 Reviewed B y: Oscar Ye EMC Mana ger Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road, Kunshan, Jiangsu province, China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RKSA200119001-00B FCC Part 15.247 Page 2 of 99 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................. 13 EXTERNAL I/O CABLE ................................................................................................................................................ 13 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 13 SUMMARY OF TEST RESULTS ............................................................................................................................. 15 TEST EQUIPMENT LIST ......................................................................................................................................... 16 FCC §1.1310 & §2.1091 –MAXIMUM PERMISSIBLE EXPOSURE (MPE) ....................................................... 17 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 19 APPLICABLE STANDARD ............................................................................................................................................ 19 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 19 FCC §15.207 (a) - AC LINE CONDUCTED EMISSIONS ...................................................................................... 20 APPLICABLE STANDARD ............................................................................................................................................ 20 EUT SETUP ................................................................................................................................................................ 20 EMI TEST RECEIVER SETUP ....................................................................................................................................... 20 TEST PROCEDURE ...................................................................................................................................................... 20 FACTOR & OVER LIMIT CALCULATION ...................................................................................................................... 21 TEST RESULTS SUMMARY .......................................................................................................................................... 21 TEST DATA ................................................................................................................................................................ 21 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS ............................................................................. 24 APPLICABLE STANDARD ............................................................................................................................................ 24 EUT SETUP ................................................................................................................................................................ 24 EMI TEST RECEIVER SETUP ................................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Conducted Emissions (Front View) Conducted Emissions (Side View) Radiated Emissions (Below 1GHz) Radiated Emissions (Above 1GHz)