2APXWODPR133Tablet with Bluetooth, WLAN

The charger should remain close to the electric socket and easily accessible while charging. Package contents • Device • USB cable • Ejection pin •USB power adaptor • Quick start guide The items supplied with the device and their images may vary by region. To turn on the device, press and hold the Side key for a few seconds. If your device is frozen and unresponsive, press and hold the Side key and the Volume Down key simultaneously for more than 7 seconds to restart it. • It is recommended not to use fixed graphics on part or all of the touchscreen for extended periods. Doing so may result in afterimages (screen burn-in) or ghosting. To prevent possible hearing damage when using a headset, do not listen to sound at high volume for long periods. Depending on the region, you can view the regulatory information on the device. To view the information, launch the Settings app. QUICK START GUIDE ODP-R133 • If any part of the device, such as the glass or acrylic body, is broken, smokes, or emits a burning odor, stop using the device immediately. • Do not turn on or use the device when the battery compartment is exposed. • Do not disassemble or reuse the battery . • Do not allow children or animals to chew or suck the device . • The device can be used in locations with an ambient temperature of 0 °C to °C. You can store the device at an ambient temperatur C to °C. Using or storing the device outside of the recommended temperature ranges may damage the device or reduce the battery’s lifespan. • Do not use your device in a hot environment or near fire. • Co mply with all safety warnings and regulations regarding mobile device usage while operating a vehicle. Correct disposal This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste. This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste. PO BOX 12987, DUBLIN, IE Safety information Read all safety information before using the device to ensure safe and proper use. You can view more safety information in the safety information menu of the Settings app. Warning Your device contains magnets, which may affect medical devices, such as pacemakers or implantable cardioverter defibrillators. If you are using any of these medical devices, keep your device a safe distance from them and consult with your physic ian before you use the device Follow the warnings below to prevent incidents, such as fires or explosions, injuries, or damage to the device • Do not expose the device to physical impact or damage. • Prevent the multipurpose jack and battery terminals from coming into contact with foreign materials such as metal, liquids, or dust. Specific Absorption Rate (SAR) certification information Your device conforms to U.S. Federal Communications Commission (FCC) standards that limit human exposure to radio frequency (RF) energy emit ted by radio and telecommunications equipment. These standards prevent the sale of mobile devices that exceed a maximum exposure level (known as the Specific Absorption Rate, or SAR) of 1.6 W/kg . In normal use, the actual SAR is likely to be much lower, as the d evice has been designed to emit only the RF energy necessary to transmit a signal to the nearest base station. By automatically emi tting lower FCC RF exposure guidelines. Some devices are required to receive approval from the FCC. If your device required FCC approval, you can view the FCC certification by opening Settings About phone S ta tus. levels when possible, your device reduces your overall exposure to RF energy. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC has granted an Equipment Authorization for this model device based on the compliance of all reported SAR levels with the 45 55 e of -10° FCC Notice FCC Notice The device may cause TV or radio interference if The device may cause TV or radio interference if used in close used in close proximity to receiving equipment. proximity to receiving equipment. The FCC can require you to The FCC can require you to stop using the stop using the mobile device if such mobile device if such interference cannot be eliminated interference cannot be eliminated . . Information about the RF exposure from FCC In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both international and U.S. standards. The design of this tablet complies with FCC guidelines and these international standards. Body effects For body operation, this device has been tested and meets FCC RF exposure guidelines when used with any accessory that contains no metal and which provides a minimum separation distance of 0 mm between this device and the body of the user. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Class B Compliance under article 15 of the FCCClass B Compliance under article 15 of the FCC This device This device complies with Part 15 of the FCCcomplies with Part 15 of the FCC Rules. Operation is subject to Rules. Operation is subject to the condition thatthe condition that this device does not cause harmful this device does not cause harmful interference.interference. Operation is subject to the following twoOperation is subject to the following two conditions: (1) this device m…

Text truncated - open the document above for the full version.

022423-17 rev 6 Certification Application Attestation Statements Date: March 21, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ______ Wingtech Group (Hong Kong) Limited ______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ______ Wingtech Group (Hong Kong) Limited ______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / ☑- is not identified on the Covered List as an entity producing “covered” equipment. Thank you, By: _________ ________ Rui Sha ________________ (Signature 2 ) (Print name) Title: _____ Manager _______ Company: Wingtech Group (Hong Kong) Limited Telephone: +86-21-53529900 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: WINGTECH INTERNATIONAL, INC. Contact Name: James Yoon Street Address: 21900 Oakview Lane City/Province/Zip: Cupertino/California/95014 Telephone No: 425-365-8532 Email: [email protected] FRN #: 0033455775 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: James Yoon Date: March 21, 2023 Signed by (Printed Name/Title): The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission- related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Wingtech Group (Hong Kong) Limited Grantee Code: 2APXW Contact Name: Rui Sha Street Address: Flat/RM 1902 19/F, Podium Plaza, 5 Hanoi Road, Tsim Sha Tsui, KL, HK City/Province/Zip: Hong Kong Telephone No: +86-21-53529900 Email: [email protected] Applicant Signature1: Rui Sha Date: March 21, 2023 Signed by (Printed Name/Title): 1 - Letters must be placed on appropriate letterhead.

050222-17 Authority to Act as Agent Date: March 22, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: ______(CTTL,Telecommunication Technology Labs,CAICT)______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____ 12 months_____ By: __________________________ _________Rui Sha___________ (Signature 1 ) (Print name) Title: _______ Manager ____________ On behalf of: __ Wingtech Group (Hong Kong) Limited _____________ (Company Name) Telephone: ________+86-21-53529900___________________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

V1.0 Attestation Letter Date: Mar. 22 th , 2023 Federal Communications Commission Authorization and Evaluation Division FCC ID: 2APXWODPR133 IC ID: / We, Samsung Electronics Co., Ltd, declare that the device does not support channel 12 ~ 13 in 2.4 GHz band and any non-US channels in all the operational mode(s) for the following product. Product: Tablet with Bluetooth,WLAN Model: ODP-R133 FCC ID: 2APXWODPR133 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Sincerely, __________________ Name: Rui Sha Position: Manager Company name: Wingtech Group (Hong Kong) Limited Tel: +86-21-53529900 Email: [email protected]

050222-17 Request for Confidentiality Date: March 27, 2023 Subject: Confidentiality Request for: ______2APXWODPR133______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☒ Short Term --------------------------- External Photos ☒ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☒ Permanent Parts List & Placement/BOM ☐ Short Term ☒ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☒ Short Term --------------------------- Test Setup Photos ☒ Short Term ☐ Permanent * 1 User’s Manual _____ Wingtech Group (Hong Kong) Limited _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __180___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications: Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By: __________________________ _____________Rui Sha___________ (Signature/Title 2 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Sample01 Sample02 Sample03 Sample04 Sample05 Sample06 Data Cable 1：21104 BROAD TELECOMMUNICATION CO LTD

Label location Back

PCB01 PCB02 PCB03 PCB04 PCB05 PCB06 PCB07 PCB08 Battery:

©Copyright. All rights reserved by CTTL. Page 1 of 115 SAR TEST REPORT No. I23Z70001-SEM01 For Wingtech Group (Hong Kong) Limited Flex Mirror Model Name: ODP-R133 with Hardware Version: REV1.0 Software Version: R133.001 FCC ID: 2APXWODPR133 Issued Date: 2023-3-24 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory: CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: [email protected], website: www.caict.ac.cn No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 2 of 115 REPORT HISTORY Report Number Revision Issue Date Description I23Z70001-SEM01 Rev.0 2023-3-21 Initial creation of test report I23Z70001-SEM01 Rev.1 2023-3-24 1. Revise frequency band for UNII band 2C on page8. 2. Add conductive power of channel 2/10 of WLAN 2.4GHz on page 21&22. No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 3 of 115 TABLE OF CONTENT 1 TEST LABORATORY ................................................................................................................ 5 1.1 TESTING LOCATION ................................................................................................................................. 5 1.2 TESTING ENVIRONMENT .......................................................................................................................... 5 1.3 PROJECT DATA ......................................................................................................................................... 5 1.4 SIGNATURE .............................................................................................................................................. 5 2 STATEMENT OF COMPLIANCE .............................................................................................. 6 3 CLIENT INFORMATION ............................................................................................................ 7 3.1 APPLICANT INFORMATION ....................................................................................................................... 7 3.2 MANUFACTURER INFORMATION .............................................................................................................. 7 4 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................. 8 4.1 ABOUT EUT ............................................................................................................................................ 8 4.2 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ................................................................... 8 4.3 INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ...................................................................... 8 5 TEST METHODOLOGY ............................................................................................................ 9 5.1 APPLICABLE LIMIT REGULATIONS ........................................................................................................... 9 5.2 APPLICABLE MEASUREMENT STANDARDS ............................................................................................... 9 6 SPECIFIC ABSORPTION RATE (SAR) .................................................................................. 10 6.1 INTRODUCTION ...................................................................................................................................... 10 6.2 SAR DEFINITION ................................................................................................................................... 10 7 TISSUE SIMULATING LIQUIDS ............................................................................................. 11 7.1 TARGETS FOR TISSUE SIMULATING LIQUID ............................................................................................. 11 7.2 DIELECTRIC PERFORMANCE .................................................................................................................. 11 8 SYSTEM VERIFICATION ........................................................................................................ 12 8.1 SYSTEM SETUP ...................................................................................................................................... 12 8.2 SYSTEM VERIFICATION .......................................................................................................................... 13 9 MEASUREMENT PROCEDURES .......................................................................................... 14 9.1 TESTS TO BE PERFORMED ....................................................................................................................... 14 9.2 GENERAL MEASUREMENT PROCEDURE ................................................................................................. 16 9.3 WCDMA MEASUREMENT PROCEDURES FOR SAR ............................................................................... 17 9.4 SAR MEASUREMENT FOR LTE .............................................................................................................. 18 9.5 BLUETOOTH & WI-FI MEASUREMENT PROCEDURES FOR SAR.............................................................. 18 9.6 POWER DRIFT ........................................................................................................................................ 19 10 AREA SCAN BASED 1-G SAR ........................................................................................... 20 10.1 REQUIREMENT OF KDB ......................................................................................................................... 20 10.2 FAST S…

Text truncated - open the document above for the full version.

No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 93 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 94 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 95 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 96 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 97 of 115 5GHz Dipole Calibration Certificate No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 98 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 99 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 100 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 101 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 102 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 103 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 104 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 105 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 106 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 107 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 108 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 109 of 115 No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 110 of 115 ANNEX I Sensor Triggering Data Summary No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 111 of 115 According to the above description, this device was tested by the manufacturer to determine the SAR sensor triggering distances for the front, rear and top edge of the device. The measured power state within ±5mm of the triggering points (or until touching the phantom) is included for rear and each applicable edge. To ensure all production units are compliant it is necessary to test SAR at a distance 1mm less than the smallest distance from the device and SAR phantom with the device at maximum output power without power reduction. We tested the power and got the different proximity sensor triggering distances for front, rear, and top edge. But the manufacturer has declared 14mm (Front) / 16mm (Rear) / 16mm (Top) are the most conservative triggering distance for wifi antenna .Therefore base on the most conservative triggering distances as above, additional SAR measurements were required at 13mm (Front) / 15mm (Rear) / 15mm (Top) for wifi antenna. No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 112 of 115 Front of Wifi antenna Moving device toward the phantom: The power state Distance [mm] 19 18 17 16 15 14 13 12 11 10 9 Main antenna Normal Normal Normal Normal Normal Low Low Low Low Low Low Moving device away from the phantom: The power state Distance [mm] 9 10 11 12 13 14 15 16 17 18 19 Main antenna Low Low Low Low Low Low Normal Normal Normal Normal Normal Rear of Wifi antenna Moving device toward the phantom: The power state Distance [mm] 20 19 18 17 16 15 14 13 12 11 10 Main antenna Normal Normal Normal Normal Normal Low Low Low Low Low Low Moving device away from the phantom: The power state Distance [mm] 10 11 12 13 14 15 16 17 18 19 20 Main antenna Low Low Low Low Low Low Normal Normal Normal Normal Normal Top of Wifi antenna Moving device toward the phantom: The power state Distance [mm] 20 19 18 17 16 15 14 13 12 11 10 Main antenna Normal Normal Normal Normal Normal Low Low Low Low Low Low Moving device away from the phantom: The power state Distance [mm] 10 11 12 13 14 15 16 17 18 19 20 Main antenna Low Low Low Low Low Low Normal Normal Normal Normal Normal No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 113 of 115 The influence of table tilt angles to proximity sensor triggering is determined by positioning each edge that contains a transmitting antenna, perpendicular to the flat phantom, at the smallest sensor triggering test distance by rotating the device around the edge next to the phantom in ≤ 10° increments until the tablet is ±45° or more from the vertical position at 0°. The rear edge evaluation The rear edge evaluation No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 114 of 115 The top edge evaluation Based on the above evaluation, we come to the conclusion that the sensor triggering is not released and normal maximum output power is not restored within the ±45°range at the smallest sensor triggering test distance declared by manufacturer. No.I23Z70001-SEM01 ©Copyright. All rights reserved by CTTL. Page 115 of 115 ANNEX J Accreditation Certificate

D01天线增益 (dbi) Test band Gain (Ant0) Gain (Ant1) Gain (BT) WIFI2.4G 2.4G -1.9 -1.7 WIFI5.8G 5G -3.1 -2.8 WIFI5.8G 5.8G -2.9 -3.0 BT BT -2.1 Length: mm

Type and shape of antenna IFA Antenna Directional characteristics Omni-directional Deflection Characteristics of Antenna Linear Type of connection with transmitter antenna shrapnel Manufacturer Zhongtianxun Communication Technology Co., LTD Measuring Organization Zhongtianxun Communication Technology Co., LTD 1.EUT Reference Setup Tester Chenzhiqiang Actual date of testing 2023-02-10 Test description Use an anechoic chamber to measure the radiation pattern and antenna gain. The GTS laboratory operates at 0.6-5.9GHz. The chamber's reflection level in the range of 0.6GHz to 5.9 GHz is typically ≤ 25 dB. Standard dipoles are used to calibrate for path loss and magnetic ring lines are used to suppress feeder emissions, so we can measure antenna gain. Test Equipment List Name of test equipment Model Manufacturer Cal.Due Date Calibtation Interval Pattern Measurement Software General Test Ray Zone 1800 NA NA Network Analyzer Agilent E5071B 2023-12-25 One year 2.Antenna distribution 3.Antenna Pattern ANT0 Front Back ANT1 Front Back BT Front Back 4.Antenna Gain ANT0.Antenna Gain： Frequency （MHz） Gain （dBi） 2400 -1.7 2450 -1.9 2500 -2.0 5150 -3.1 5550 -3.2 5850 -2.9 ANT1.Antenna Gain： Frequency （MHz） Gain （dBi） 2400 -1.4 2450 -1.7 2500 -1.9 5150 -2.8 5550 -3.1 5850 -3.0 BT.Antenna Gain： Frequency （MHz） Gain （dBi） 2400 -1.8 2450 -2.1 2500 -1.6 5.3D map ANT0 2400MHz 2450MHz 2500MHz 5150MHz 5550MHz 5850MHz ANT1 2400MHz 2450MHz 2500MHz 5150MH 5550MHz 5850MHz BT 2400MHz 2450MH 2500MHz

©Copyright. All rights reserved by CTTL. FCC PART 15C TEST REPORT BLUETOOTH LOW ENERGY (BLE) PART No. I23Z70001-IOT01 for Wingtech Group (Hong Kong) Limited Flex Mirror Model Name: ODP-R133 FCC ID: 2APXWODPR133 with Hardware Version: REV1.0 Software Version: R133.001 Issued Date: 2023-3-8 Note: The test results in this test report relate only to the devices specified in this report.This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory: CTTL, Telecommunication Technology Labs, CAICT No.52, HuayuanNorth Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512,Fax:+86(0)10-62304633-2504 Email:[email protected], website: www.chinattl.com No. I23Z70001-IOT01 ©Copyright. All rights reserved by CTTL. Page 2 of 44. REPORT HISTORY Report Number Revision Description Issue Date I23Z70001-IOT01 Rev.0 1st edition 2023-3-8 No. I23Z70001-IOT01 ©Copyright. All rights reserved by CTTL. Page 3 of 44. CONTENTS 1. TEST LABORATORY ......................................................................................................................... 5 1.1. INTRODUCTION &ACCREDITATION .................................................................................................. 5 1.2. TESTING LOCATION ......................................................................................................................... 5 1.3. TESTING ENVIRONMENT .................................................................................................................. 6 1.4. PROJECT DATA ................................................................................................................................. 6 1.5. SIGNATURE ...................................................................................................................................... 6 2. CLIENT INFORMATION ................................................................................................................... 7 2.1. APPLICANT INFORMATION ............................................................................................................... 7 2.2. MANUFACTURER INFORMATION ...................................................................................................... 7 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................. 8 3.1. ABOUT EUT .................................................................................................................................... 8 3.2. INTERNAL IDENTIFICATION OF EUT ................................................................................................ 8 3.3. INTERNAL IDENTIFICATION OF AE ................................................................................................... 8 3.4. NORMAL ACCESSORY SETTING .....................................................................................…

Text truncated - open the document above for the full version.