2AS9T-SB12-SOMUSE-R

Model : SB12 Quick Start Guide MUSE-RService Call Button Version 1.0 Appearance Offer personal assistance services to your customers •A stationary button for service call with desk/wall mounting bracket •Simple & user-friendly design for a wide range of applications •Equipped with a rechargeable battery with micro-USB connector •Great convenience for customer service orders (consumer goods, office supplies, food, taxi, staff call, call back service, parcel pickup) •Preventive security and maintenance solutions for your business Feature LED Indicator Button Micro-USB 5-pin connector Mounting bracket Double-sided adhesive tape Magnet Screws Activate NFC on your phone and tag it on to the bottom of your device. The indicator light will flash red when the device is powered on. Turning the power on Charging the battery When the battery level is low, the red LED blinks twice every 5 seconds. To charge : (1)Plug the small end of the USB charging cable into the micro-B USB connector on your device. (2)Plug the other end into a USB wall charger or computer that is powered on. The indicator light blinks every second while charging and turns red when fully charged. Sending message When the button is pressed, the indicator light flashes red and the device sends a message. IMPORTANT: Please read and comply with all of the instructions provided in this manual before using the device. Failure to comply with the instructions given in this manual and/or using the device in ways other than the ones mentioned in this manual may result in serious injury and/or damage the product. - Do not use while it is charging. - Do not drop, knock, or shake the device. - Do not disassemble as it may cause malfunctions. - Do not use the device in corrosive liquid or excessive heat environment. - Keep the device more than 20cm away from the human body during use. - Long time (more than 3 months) storage: If the device is stored for a long time, the battery's storage voltage should be 3.6~3.9V and the battery is to be stored in a condition as Temperature 15~35 °C, Relative Humidity 45~85% RH, Atmospheric Pressure 86~106 KPa. Also, it is recommended to charge the battery every six months. Safety Instruction Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Copyright ©2019 AMOSENSE Co.,Ltd. All rights reserved. No copying, distribution, publication, modification, or incorporation of this document, in whole or part, it is permitted for commercial purposes without the express written permission of AMOSENSE. The contents of this document may be changed without prior notice. Device Specifications Customer Support Address : 165 North Archer Avenue Mundelein, IL 60060, USA Mobile : 1-224-619-6579 Email: [email protected] Web: www.amosenseiot.com SB12 32-bit Arm® based Cortex®-M0, 256KB Flash Sigfox RC 2 Uplink Class0u (>20dBm EIRP) / Bluetooth LE 5.0, NFC Sigfox geolocation -20 ~ 50 °C LED indicator & Push Button IPX4, PC/ABS Housing Rechargeable 3.7V Lithium Ion Cell Mounting Bracket R 43 x H 14.5 mm, 21.2g Model Number MCU Connectivity Positioning Operation Temp User Interface Mechanical Casing Battery Accessories Dimensions FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

AMOSENSE Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: April 08, 2021 Subject; Request for Confidentiality FCC ID: 2AS9T-SB12-SO To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. • Schematic Diagram • Block Diagram • Part List • Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission' s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. • External Photos • Internal Photos • Test Setup Photos • User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Taik Jin, Yang Title: Principal engineer

Letter of Authorization Company : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Product Name : MUSE-R Model Number : SB12 FCC Identifier : 2AS9T-SB12-SO We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Taik Jin, Yang Date: April 08, 2021 Title: Principal engineer Signature of applicant:

Page 1 of 6 Page 2 of 6 Page 3 of 6 Page 4 of 6 Page 5 of 6 Page 6 of 6

Page 1 of 1

Page 1 of 8 Page 2 of 8 Page 3 of 8 Page 4 of 8 Page 5 of 8 Page 6 of 8 Bluetooth LE Chip Antenna Page 7 of 8 Sig Fox Chip Antenna Metal Antenna Page 8 of 8 NFC Simple tag function

Page 1 of 7 Report No.: OT-214-RWD-021 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) ELECTROMAGNETIC EMISSION C OMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : OT-214-RWD-021 Reception No. : 2103001384 Applicant : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Manufacturer : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Type of Equipment : MUSE-R FCC ID. : 2AS9T-SB12-SO Model Name : SB12 Multiple Model Name : N/A Serial number : N/A Total page of Report : 7 pages (including this page) Date of Incoming : April 01, 2021 Date of issue : April 08, 2021 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Tested by Hyung-Kwon, Oh / Manager ONETECH Corp. Reviewed by Tae-Ho, Kim / Senior Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 7 Report No.: OT-214-RWD-021 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 5 3. EUT MODIFICATIONS .................................................................................................................................................... 5 4. MAXIMUM PERMISSIBLE EXPOSURE ...................................................................................................................... 6 4.1 APPLICABLE STANDARD ................................................................................................................................................ 6 4.2 TEST RESULT ................................................................................................................................................................. 7 Page 3 of 7 Report No.: OT-214-RWD-021 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) Revision History Rev. No. Issue Report No. Issued Date Revisions Section Affected 0 OT-214-RWD-021 April 08, 2021 Initial Release All Page 4 of 7 Report No.: OT-214-RWD-021 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 1. VERIFICATION OF COMPLIANCE Applicant : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Manufacturer : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Contact Person : Taik Jin, Yang / Principal engineer Telephone No. : +82-10-3795-4037 FCC ID : 2AS9T-SB12-SO Model Name : SB12 Brand Name : - Serial Number : N/A Date : April 08, 2021 EQUIPMENT CLASS DSS – PART 15 SPREAD SPECTRUM TRANSMITTER DTS – DIGITAL TRNSMISSION SYSTEM E.U.T. DESCRIPTION MUSE-R THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES ANSI C63.10: 2020 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) FCC PART 15 SUBPART C Section 15.247 558074 D01 15.247 Meas Guidance v05r02 Modifications on the Equipment to Achieve Compliance None Final Test was Conducted On 3 m, Semi Anechoic Chamber -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 7 Report No.: OT-214-RWD-021 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 2. GENERAL INFORMATION 2.1 Product Description The AMOSENSE, Model SB12 (referred to as the EUT in this report) is an MUSE-R, Product specification information described herein was obtained from product data sheet or user’s manual. DEVICE TYPE MUSE-R Temperature Range -20 °C ~ 50 °C OPERATING FREQUENCY Sig Fox 902.137 5 MHz ~ 904.662 5 MHz Bluetooth LE 2 402 MHz ~ 2 480 MHz MODULATION TYPE Sig Fox DBPSK Bluetooth LE GFSK RF OUTPUT POWER’ Sig Fox 22.55 dBm Bluetooth LE -1.01 dBm ANTENNA TYPE Sig Fox: Chip + Metal Antenna Bluetooth LE: Chip Antenna ANTENNA GAIN Sig Fox: 0.57 dBi Bluetooth LE: -0.02 dBi List of each Osc. or crystal Freq.(Freq. >= 1 MHz) 32.768 kHz, 32 MHz, 50 MHz 2.2 Alternative type(s)/model(s); also covered by this test report. -. None 3. EUT MODIFICATIONS -. None Page 6 of 7 Report No.: OT-214-RWD…

Text truncated - open the document above for the full version.

Page 1 of 38 Report No.: OT-214-RWD-020 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) ELECTROMAGNETIC EMISSION C OMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : OT-214-RWD-020 Reception No. : 2103001384 Applicant : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Manufacturer : AMOSENSE Address : 19-1BL, 90, 4Sandan 5 gil, Jiksan-eup, Cheonan-Si, Chungcheongnam-Do, South Korea Type of Equipment : MUSE-R FCC ID. : 2AS9T-SB12-SO Model Name : SB12 Multiple Model Name : N/A Serial number : N/A Total page of Report : 38 pages (including this page) Date of Incoming : April 01, 2021 Date of issue : April 08, 2021 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Tested by Hyung-Kwon, Oh / Manager ONETECH Corp. Reviewed by Tae-Ho, Kim / Senior Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 38 Report No.: OT-214-RWD-020 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 5 2. TEST SUMMARY .............................................................................................................................................................. 6 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 6 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 6 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 6 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 6 2.5 TEST METHODOLOGY .................................................................................................................................................... 6 2.6 TEST FACILITY ............................................................................................................................................................... 6 3. GENERAL INFORMATION ............................................................................................................................................ 7 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 7 4. EUT MODIFICATIONS .................................................................................................................................................... 7 5.1 JUSTIFICATION ............................................................................................................................................................... 8 5.2 PERIPHERAL EQUIPMENT .............................................................................................................................................. 8 5.3 MODE OF OPERATION DURING THE TEST ...................................................................................................................... 8 -. CHANNEL LIST .................................................................................................................................................................. 10 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................. 12 6. PRELIMINARY TEST .................................................................................................................................................... 12 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ....................................................................................................... 12 6.2 GENERAL RADIATED EMISSIONS TESTS ..................................................................................................................... 12 7. MINIMUM 6 DB BANDWIDTH .................................................................................................................................... 13 7.1 OPERATING ENVIRONMENT ......................................................................................................................................... 13 7.2 TEST SET-UP ................................................................................................................................................................. 13 7.3 TEST DATE ................................................................................................................................................................... 13 7.4 TEST DATA .................................................................................................................................................................... 14 8. MAXIMUM PEAK OUTPUT POWER ......................................................................................................................... 16 8.1 OPERATING EN…

Text truncated - open the document above for the full version.

Page 1 of 3 - CONDUCTED EMISSION TEST Page 2 of 3 - RADIATED EMISSION TEST Page 3 of 3