2AU8HSRP410-ALTE CPE

Use a cross screwdriver to remove the SIM card cover. Slide the SIM cards into the SIM card slots until they click into place. By default, the SIM card in slot 1 (the upper slot) is the Primary SIM card. When the SRP router is powered on or reboots, it automatically connects to the network associated with the Primary SIM card. Re-attach the cover. SRP Series Quick Start Guide Welcome to the SRP Series Smawave SRP series ruggedized outdoor CPE provides LTE service in a ruggedized form factor. With an operating temperature range of -40°C to +70°C endurance, they offer industrial-grade environmental qualifications while providing higher speeds data services for video and other bandwidth-intensive applications. SRP series industrial CPE has very strong anti-vibration ability and it is qualified for extreme industrial environments and ideally suited for rail, transportation, mining, oil and gas, manufacturing, and other outdoor applications. With the diverse self-developed LTE-A embedded modules integrated, SRP series industrial CPE can support multi-bands for Private LTE, even support uncommon frequencies. SRP series industrial CPE can provide accurate real-time location information. The built-in GNSS receiver supports GPS, GLONASS, BEIDOU and Galileo constella- tions. This document will serve as a quick start guide for SRP series ruggedized outdoor CPE. In this document, the SRP series ruggedized outdoor CPE will be replaced by the CPE. Carefully read the following safety symbols to help you use your CPE safely and correctly. Equipment Appearance The reset button is beside SIM interface, if press 1s, CPE will restart; if press above 10s, CPE will factory reset. There are two white ground screws also at behind of device. Note1 Step1 Step2 Step3 Note2 RS232/485 Cable Definition M12 RS232/485 cable definition NumberColorsRS485RS232+DIDO 8 7 6 5 4 3 2 1 BrownRS485_ARS232_RX RS232_TX RS_GND RS_GND DI1 DO1 DI2 DO2 RS485_B RS_GND RS_GND RS_GND RS_GND NC NC Brown&white Green Blue&white Blue Green&white Orange Orange&white Working Environment Power Supply 9~36VDC Power Consumption Water and Dustproof 12W IP67 Operating Storage Humidity -40°C~ 70°C -40°C~80°C 5%~95% Packing List M12 A-Code cable to RJ45 jack ADC2 Ethernet cable ItemsAccessoriesQty M12 A-Code 8Pin cable ADB1Data cable M12 A-Code 4Pin cable M12APower cable Mounting bolts (M5*20) Grounding cable M12 Protective cap TNC protective cap 1 2 3 4 5 6 7 1 1 1 4 1 5 3/5 Configure Hardware Install SIM Cards Connect and Turn on the Router 3.Connect the WIFI1 antennas and WIFI2 if applicable. 1.Connect the ANT1 and ANT2 Cellular antennas. 2.Connect the GPS antenna if applicable. 5.Connect a computer to the router with an Ethernet cable. 6.Connect 9-36 VDC power cable. 7.Connect devices to the RS232/RS485/DIDO ports. Connect to the Network When the router is powered on, a green PWR LED may occur. This indicates that the power input is good. Once the router’s radio module is configured for the SIMcard, it begins the activation/provisioning process and attempts to connect to the mobile network. This process typically takes several minutes. A successful connection is indicated by a solid green NET LED. And the strength of the RF signal can be indicated by the RSSI LED in different colors. 12345 6 4.Connect the protecting ground cable. Green Off Green Off Green Yellow Red Off Power on No power supply Register to network Not register to network Signal strong Signal good Signal weak No signal PWR NET RSSI Login to the Web Management Page Launch the web browser, enter http://192.168.0.1 in the address bar, and press Enter. Enter the user name and password, and click Log In. You can login to the web management page after the password is verified. Configure Software Step1 Step2 Step3 The default user name and password are both admin. If you want to view or configure the CPE more, you should use the super account to log in to the web management page. The default super user name is superadmin, and the password is admin. LTE Settings To set the LTE network, perform the following steps: Choose Network >LTE Settings; In the Settings area, you can set the configuration of LTE network; In the Status area, you can view the LTE network connect status, such as Frequency, RSSI, RSRP, RSRQ,CINR, SINR, Cell ID and so on. Step1 Step2 Step3 FAQs The POWER indicator does not turn on. Make sure that the power cable is connected proper- ly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Login the web management page. Make sure that the CPE is started. WLAN Settings Choose Settings Wi-Fi WLAN Settings. In the General Settings area, set Wi-Fi Enable or enable Wi-Fi. In the Setting area, change the SSID, such as "LTE-Router". To ensure data security, it is recommended that you change the Wi-Fi password . Click Submit to save the settings. Step1 Step2 Step3 Step4 Step5 Verify that the CPE is correctly connected to the computer through Wi-Fi or a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigera- tors, and satellite dishes. If the problem persists, contact authorized local service suppliers. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. The CPE do not support SIM card hot-plug, please confirm that the device has been powered off when the SIM card is inserted or removed. 7 8 91011 FCC Regulations: This dev…

Text truncated - open the document above for the full version.

Declaration Herebywe, Nameofmanufacturer:ShanghaiSmawaveTechnologyCo.,Ltd Address:3/F,Building8,1001NorthQinzhouRoad，XuhuiDistrict,Shanghai, China Zipcode&City:Shanghai Country:China Telephonenumber:/ declarebelowproduct: Productdescription:LTECPE Typedesignation(s):SRP410-a FCCID:2AU8HSRP410-A Trademark:Smawave Whichassemblesthebelowmodules Productdescription:LTEmodule Typedesignation(s):MGL6201A Trademark:Smawave FCCID:2AU8HMGL6201A CanquotedirectlytheRFconductedtestreportofFCCcertification，andtheoriginal testreportsaccuratelyrepresenttestresultsontheSRP410-a.Becausethemoduleis embeddedintheSRP410-a,thendirectlyconnecttoantennatosentRFsignalto communicationnetwork，SothisdesignwillnotimpactthemoduleRFconnectedperformance andcanensuretheRFconductedtestresultisaccordancewithoriginalreportonthe newproduct.Andthereferencedreportnumberasbelow. R2001A0002-R1 R2001A0002-R2 R2001A0002-R3 R2001A0002-R4 R2001A0002-R5 R2001A0002-R6 R2001A0002-R7 Signedforandonbehalfof: Date:6/5/2020 City:Shanghai PrintName:wangfei Signature: Company:ShanghaiSmawaveTechnologyCo.,Ltd

ShanghaiSmawaveTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 Subject;RequestforLongTermConfidentiality FCCID:2AU8HSRP410-A ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,weare requestingtheCommissiontowithholdthefollowingattachment(s)asconfidentialdocumentsfrom publicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure SoftwareSecurityDescription UNIIdeclarationletter Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatandcorrespondence duringthecertificationreviewprocesscannotbegrantedasconfidentialdocumentsandthis informationwillbeavailableforpublicreviewoncethegrantofequipmentauthorizationisissued. Sincerely, Date:2020-4-29 Signature: Name(inprint):wangfei Company:ShanghaiSmawaveTechnologyCo.,Ltd Adreess:3FBuilding81001NorthQinzhouRoadXuhuiDistrictShanghaiChina

ShanghaiSmawaveTechnologyCo.,Ltd POWEROFATTORNEY DATE:May7,2020 To: FederalCommunicationsCommission, Authorization&EvaluationDivision, 7435OaklandMillsRoad, Columbia,MD21046 We,theundersigned,herebyauthorizeTATechnology(Shanghai)Co.,Ltd./zhaojunllinonour behalf,toapplytoFCConourequipmentforFCCID:2AU8HSRP410-A.Anyandallactscarriedout byTATechnology(Shanghai)Co.,Ltd.onourbehalfshallhavethesameeffectasactsofourown forthiscertificate. Sincerely, Date:2020-4-29 Signature: Name(inprint):wangfei Company:ShanghaiSmawaveTechnologyCo.,Ltd Adreess:3FBuilding81001NorthQinzhouRoadXuhuiDistrictShanghaiChina

EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 1 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 2 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 3 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 4 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. a: EUT Picture 1: Constituents of EUT

EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 1 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 2 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 3 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. Page 4 of 4 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. a: EUT Picture 1: Constituents of EUT

LabelLocation Company: ShanghaiSmawaveTechnologyCo.,Ltd Model: SRP410-a LabelLocation Company: ShanghaiSmawaveTechnologyCo.,Ltd Model: SRP410-a Packagelabel

EUTAppearanceReportNo.:R2001A0002 TATechnology(Shanghai)Co.,Ltd.Page1of2 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. EUTAppearance EUTAppearanceReportNo.:R2001A0002 TATechnology(Shanghai)Co.,Ltd.Page2of2 Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofTATechnology(Shanghai)Co.,Ltd. a:EUT Picture1:ConstituentsofEUT

SRP410-a

MPE TEST REPORT Applicant Shanghai Smawave Technology Co. ,Ltd FCC ID 2AU8HSRP410-A Product LTE CPE Brand Smawave Model SRP410-a Report No. R2001A0014-M1V1 Issue Date May 7, 2020 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC 47 CFR Part 1 1.1310. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Yu Wang Approved by: Guangchang Fan TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000 MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 2 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Table of Contents 1 Test Laboratory ............................................................................................................................... 3 1.1 Notes of the Test Report ......................................................................................................... 3 1.2 Testing Location ...................................................................................................................... 3 1.3 Laboratory Environment .......................................................................................................... 4 2 Description of Equipment under Test .............................................................................................. 5 3 Maximum conducted output power (measured) and antenna Gain ................................................ 6 4 Test Result ..................................................................................................................................... 7 MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 3 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2. Test facility FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. 1.3. Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China City: Shanghai Post code: 201201 Country: P. R. China Contact: Fan Guangchang Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: [email protected] MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 4 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1.4. Laboratory Environment Temperature Min. = 18C, Max. = 25 C Relative humidity Min. = 30%, Max. = 70% Ground system resistance < 0.5  Ambient noise is checked and found very low and in compliance with requirement of standards. Reflection of surrounding objects is minimized and in compliance with requirement of standards. MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 5 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 2 Description of Equipment under Test Client Information Applicant Shanghai Smawave Technology Co. ,Ltd Applicant address 3/F, Building 8, 1001 North Qinzhou Road，Xuhui District, Shanghai, China Manufacturer Shanghai Smawave Technology Co. ,Ltd Manufacturer address 3/F, Building 8, 1001 North Qinzhou Road，Xuhui District, Shanghai, China General Technologies Model SRP410-a SN 6201A20010300144 Hardware Version SGL6010_V1.2 Software Version SG626_V1.0 Date of Testing: October 1, 2019~ November 7, 2019 Note: This revised report (Report No.: R2001A0014-M1V1) supersedes and replaces the previously issued report (Report No.: R2001A0014-M1). Please discard or destroy the previously issued report and dispose of it accordingly. MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 6 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 3 Maximum conducted output power (measured) and antenna Gain The numeric gain (G) of the antenna with a gain specified in dB is determined by Numeric gain (G)=10^(antenna gain/10) Band Maximum Conducted Output Power (dBm) Antenna Gain (dBi) Numeric gain (dBm) (mW) LTE Band 2 24.000 251.189 2.150 1.641 LTE Band 4 24.000 251.189 1.490 1.409 LTE Band 5 23.500 223.872 2.780 1.897 LTE Band 12 24.000 251.189 1.040 1.271 LTE Band 13 24.000 251.189 1.040 1.271 LTE Band 14 24.000 251.189 2.780 1.897 LTE Band 25 24.000 251.189 2.150 1.641 LTE Band 26 24.000 251.189 2.780 1.897 LTE Band 41 24.000 251.189 3.990 2.506 LTE Band 48 24.500 281.838 3.710 2.350 LTE Band 53 24.500 281.838 4.220 2.642 LTE Band 66 24.000 251.189 1.490 1.409 Wi-Fi 2.4G 18.250 66.834 5.000 3.162 Wi-Fi 5G 16.970 49.774 5.000 3.162 MPE Test Report Report No.: R2001A0014-M1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-013S Page 7 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 4 Test Result According to …

Text truncated - open the document above for the full version.

RF TEST REPORT Applicant Shanghai Smawave Technology Co. ,Ltd FCC ID 2AU8HSRP410-A Product LTE CPE Brand Smawave Model SRP410-a Report No. R2001A0014-R7V1 Issue Date May 7, 2020 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 2 (2019)/ FCC CFR 47 Part 25 (2019). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Peng Tao Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000 RF Test Report Report No.: R2001A0014-R7V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-014R Page 2 of 13 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. TABLE OF CONTENT 1. Test Laboratory ...................................................................................................................................... 4 1.1. Notes of the test report .................................................................................................................. 4 1.2. Testing Location ............................................................................................................................ 4 2. General Description of Equipment under Test ....................................................................................... 5 2.1. Applicant and Manufacturer Information ....................................................................................... 5 2.2. General information ....................................................................................................................... 5 3. Applied Standards .................................................................................................................................. 6 4. Test Configuration .................................................................................................................................. 7 5. Test Case Results .................................................................................................................................. 8 5.1. Radiates Spurious Emission ......................................................................................................... 8 6. Main Test Instruments ......................................................................................................................... 13 RF Test Report Report No.: R2001A0014-R7V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-014R Page 3 of 13 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Summary of measurement results No. Test Case Clause in FCC rules Verdict 1 Radiates Spurious Emission 2.1053 PASS Note: PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard. Date of Testing: November 30, 2019 ~ March 13, 2020 Only Radiates Spurious Emission are tested in this report, and other conducted items please refer to the MGL6201A module report(Report No.: R2001A0002-R7). Note: This revised report (Report No.: R2001A0014-R7V1) supersedes and replaces the previously issued report (Report No.: R2001A0014-R7). Please discard or destroy the previously issued report and dispose of it accordingly. RF Test Report Report No.: R2001A0014-R7V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-014R Page 4 of 13 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1. Test Laboratory 1.1. Notes of the test report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2. Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: [email protected] RF Test Report Report No.: R2001A0014-R7V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-014R Page 5 of 13 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 2. General Description of Equipment under Test 2.1. Applicant and Manufacturer Information Applicant Shanghai Smawave Technology Co. ,Ltd Applicant address 3/F, Building 8, 1001 North Qinzhou Road，Xuhui District, Shanghai, China Manufacturer Shanghai Smawave Technology Co. ,Ltd Manufacturer address 3/F, Building 8, 1001 North Qinzhou Road，Xuhui District, Shanghai, China 2.2. General information EUT Description Model SRP410-a IMEI 6201A20010300144 Hardware Version SGL6010_V1.2 Software Version SG626_V1.0 Power Supply DC Power Antenna Type External Antenna Antenna Gain 3.60 dBi Test Mode(s) LTE Band 53; Test Modulation (LTE)QPSK, 16QAM, 64QAM; LTE Category 12 Rated Power Supply Voltage 12V Extreme Voltage Minimum: 9V Maximum: 14V Extreme Temperature Lowest: -40°C Highest: +70°C Operating Frequency Range(s) Band Tx (MHz) Rx (MHz) LTE Band 53 2483.5 ~ 2495 2483.5 ~ 2495 Note: 1. The information of the EUT is declared by the manufacturer. RF Test Report Report No.: R2001A0014-R7V1 TA Technology (Shanghai) Co., Ltd. TA-MB-01-014R Page 6 of 13 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 3. Applied Standards According to the specifications of the manufacturer, it must…

Text truncated - open the document above for the full version.

RF Test Setup Report No.: R2001A0014 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 1 of 1 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Part22_24_25_27_90 Test Setup 30MHz-1GHz 1GHz-18GHz Picture 1: Radiated Spurious Emissions Test setup