2AV9UFZ105Android Media Player

Installation Guide ＿ 0 Connect your FORMULER to your TV with an HDMI cable. 行 8 Connect your FORMULER to power using the power cord 色 E) Turn on your TV and switch to the cor『ectHDMI input 巳0 Set-up your FORMULER and connect to your local network 艺气: ＿ 8 Install your favorite apps to enjoy streaming contents• ＿ What's in the Box? Q ｀ Media Receiver Remote Control ｀ ｀ Remote Control Extender 2x Batteries 文 ｀ TV Cable Power Adapter lnstallationsanleitung ＿ 0 Verbinden Sie lhre FORMULER und den Fernseher mil einem HDMI Kabel. 行8 SchlieBen Sie lhre FORMULER Ober das Netzkabel an die Stromversorgung an. 色 8 Schalten Sie 1hr Fernsehge闭tein und wechseln Sie zum richtigen HDMI-Eingang 巳0 Rich t e n Sie lhre FORMULER ein und s tellen Sie eine Verbindung zum lokalen Netzwerk her. 艺气: 8 lnstallieren Sie lhre gewiinschten Apps um die Streaming - Angebote geniel!en zu konnen• ＿ Was ist in der Box? Q Medienempfanger Fernbedienung 气 ｀ Fernbedienung Extender 2 x Batterien 文 气 TV-Kabel Netzteil RED Declaration FORMULER hereby declares that this wi『elessdevice complies with all material requirements and other『elevantprovisions of the 2014/53/EU Directive. A copy of the Declaration of Conformity may be obtained directly from COBOPLUS [C/ INDEPENDENCIA, N2 BAJO DERECHA A y 8, 28013, MADRID, SPAIN) For technical support, 『egulatorycompliance information, and use『guide,visit https;t /support. formuler.tv SAFETY INFORMATION FORMULER products a『e designed to operate safely when installed and used acco灿ngto the product instructions and general safety practices. The guidelines included in this document explain the potential『isksassociated with equipment operation and p『ovideimportant safety practices designed to min血izethese risks. By ca『efullyfollowing the information contained in this document, you can protect yourself from haza『dsand c『eatea safer environment. This product is designed and tested to meet JEC 62368-1, the Standard for Safety of Information Technology Equipment. This also cove『sthe implementation of IEC 62368-1 based safety standards around the wo『Id,e.g. UL 60950-1. Retain and follow all product safety and operating instructions. Always『efe『to the documentation supplied with your equipment. Observe all warnings on the product and in the operating instructions Note: Read all safety information below and ope『atinginstructions before using FORMULER to avoid injury. WARNING: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK OR OTHER INJURY OR DAMAGE. ELECTRICAL EQUIPMENT CAN BE H应ARDOUSIF MISUSED. OPERATION OF THIS PRODUCT, OR SIMILAR PRODUCTS, MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THE INTERIOR OF ANY ELECTRICAL PRODUCT AND DO NO PERMIT THEM TO HANDLE AND CABLES. SYMBOLS ON THE EQUIPMENT 宜This is a universal『ecyclingsymbol indicating that the battery cannot be disposed of in the t『 ash _ and must be recycled according to the『egulationsand/o『O咄nancesof the local commun灯 To reduce the『isk of personal injury, elect『ic shock, fire, o『damageto the equipment, observe the following precautions· Follow all cautions and Instructions marked on the equipment -Do not bend, drop, c『ush, puncture, incine『ate, or push objects into openings of FORMULER -Do not connect or disconnect any cables o『performmaintenance o『『econfigurationof this product du『ing an elect『ical sto『m -Do not use FORMULER in wet locations. In case FORMULER gets wet, unplug all cables and turn off befo『e cleaning, and allow it to dry thoroughly before turning it on again -Never turn on any equipment when there is evidence of fire, wate『,or structural damage -Place the product away from heat sou『ces. -Never force a connector into a port. Make sure the connecto『matchesthe port before inserting. -Always use a FORMULER approved powe『adapte『.Do not connect o顷sconnectthe AC Power Adapter with wet hands. The powe『adapte『is intended for indoor use only -Operate the AC adapte『in a ventilated a『ea -Do no make mechanical or electrical modifications to the equipment -Neve『attemptto repai『FORMULERyou『self.Do not attempt to open, disassemble the device You『un the risk of electric shock -Operate FORMULER in a place whe『ethe tempe『atu代is always between 5 and 30 deg『ees Celsius -Use this product only with approved equipment and/or accesso『ies POWER RA TING : 12 voe. 1.0A D缸laratlonRED FORMULER declare pa『la p『esenteque cet appareil sans fil『espectetoutes les exigences mate『ielles et autres dispositions pertinentes de la Directive 2014/53 / LIE. Une copie de la D的a『ationde Conformite peut知obteooedr出血玑au啦sde COBOPI..US (Cl INDEPENDENCIA, N2队IJERECHAAyB,2B013息OOID,SPAIN( Pour obteni『une assistance technique, des info『mationssu『la conformite aux『eglementationset un manuel d'utilisation, visitez le site https;//support. formuler ,tv INFORMATION SUR LA StCURITt Les produits FORMULER sont concus pou『fonctionneren toute securite lorsqu'ils sont installes et utilises confo『mementaux inst『uctionsdu produit et aux consignes de s的uritegenerales. Les di『ectivesincluses dans ce document expliquent les risques potentiels associes au fonctionnement de I'的uipementet fournissent des pratiques de secu『眙mportantesconcues pou『minimiserces『isques En suiYant attentiYement les informations contenues dans ce document, Yous pouYez Yous prot的erdes dange『Set C『ee『un enYironnement plus s山 Ce produit a ete concu et teste pour『epondrea la norme IEC 62368-1, norme su『la secu『ite des 的uipementsinfo『matiques.Cela couYre egalement la mise en teuYre des no『mesde securite basees sur la IEC 62368-1 dans le monde entier, pa『exemple.UL 60950-1. Conserve, et suiyez toutes les instructions de securite et d'utilisation du prodult. Consultez tou1ou『S a la documentation fournie aYec Yot『e equipement. Observe, tous les aYertissements sur le produit et dans les inst『uctionsd'utilisation. Remarque: lisez toutes les info『mationsde securite ci-dessous ainsi que les instructions d'utilisation aYant d'utilise『FORMULERafin d'eYite『Yousblesse『 AVERTISS…

Text truncated - open the document above for the full version.

ALOYS INC. Agent Authorization Company: ALOYS INC. Address: #6F, MARCUS Bldg., 4-5, Yanghyeon-ro405beon-gil, jungwon-gu, Seongnam-si, Gyeonggi-do, South Korea Product Name: Formuler Z11 Pro Max Trade Mark: FORMULER Model Number(s): Z11 Pro Max FCC ID: 2AV9UFZ105 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022-07-26 Name: martin Title: Manager Company: ALOYS INC.

ALOYS INC. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022-07-26 Subject; Request for Confidentiality FCC ID: 2AV9UFZ105 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Software Security Requirements For U-NII Devices Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: martin Title: Manager

Page 1 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Fig. 1 Fig. 2 Page 2 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 6 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 Fig. 12

Page 1 of 1 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L: 5.0cm x W: 5.0cm) Label Location Formuler Z11 Pro Max Model: Z11 Pro Max FCC ID: 2AV9UFZ105

Page 1 of 3 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 WIFI ANT 0 WIFI ANT 1 Page 2 of 3 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 BT ANT Page 3 of 3 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6

Page 1 of 15 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Maximum Permissible Exposure Report 1. Product Information FCC ID: 2AV9UFZ105 Product name Formuler Z11 Pro Max Test Model Z11 Pro Max Power supply For Adapter Input: 100-240V~, 50/60Hz For Adapter Output: 12V1.0A Hardware Version FZ105 Software Version 10.12.1-r811350428 Bluetooth Frequency Range 2402MHz ~ 2480MHz Channel Number 79 channels for Bluetooth V5.2(DSS) 40 channels for Bluetooth V5.2 (DTS) Channel Spacing 1MHz for Bluetooth V5.2 (DSS) 2MHz for Bluetooth V5.2 (DTS) Modulation Type GFSK, π/4-DQPSK, 8-DPSK for Bluetooth V5.2(DSS) GFSK for Bluetooth V5.2 (DTS) Bluetooth Version V5.2 Antenna Description Internal Antenna, 2.0dBi (max.) 2.4G WLAN Frequency Range 2412MHz ~ 2462MHz Channel Spacing 5MHz Channel Number 11 Channels for 20MHz bandwidth (2412~2462MHz) 7 Channels for 40MHz bandwidth (2422~2452MHz) Modulation Type IEEE 802.11b: DSSS (CCK, DQPSK, DBPSK) IEEE 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11n: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11ax: OFDM (64QAM, 16QAM, QPSK, BPSK) Antenna Description Antenna 0: Internal Antenna, 2.0dBi (max.) Antenna 1: Internal Antenna, 2.0dBi (max.) 5.2G WLAN Frequency Range 5180-5240MHz Channel Number 4 Channels for 20MHz bandwidth(5180MHz-5240MHz) 2 channels for 40MHz bandwidth(5190MHz~5230MHz) 1 channels for 80MHz bandwidth(5210MHz) Modulation Type IEEE 802.11a/n/ac/ax: OFDM (256QAM, 64QAM, 16QAM, QPSK, BPSK) Antenna Description Antenna 0: Internal Antenna, 2.0dBi (max.) Antenna 1: Internal Antenna, 2.0dBi (max.) 5.8G WLAN Frequency Range 5745MHz-5825MHz Page 2 of 15 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Channel Number 5 channels for 20MHz bandwidth(5745MHz-5825MHz) 2 channels for 40MHz bandwidth(5755MHz~5795MHz) 1 channels for 80MHz bandwidth(5775MHz) Modulation Type IEEE 802.11a/n/ac/ax: OFDM (256QAM, 64QAM, 16QAM, QPSK, BPSK) Antenna Description Antenna 0: Internal Antenna, 2.0dBi (max.) Antenna 1: Internal Antenna, 2.0dBi (max.) Exposure category General population/uncontrolled environment EUT Type Production Unit Device Type Mobile Devices 2. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. 3. Limit 3. 1 Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: Mobile Devices Page 3 of 15 FCC ID: 2AV9UFZ105 Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 3. 2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 4. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input t…

Text truncated - open the document above for the full version.

Page 1 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Appendix A RF Test Data for BT (Conducted Measurement) Product Name: Formuler Z11 Pro Max Test Model: Z11 Pro Max Environmental Conditions Temperature: 23.9  C Relative Humidity: 52.1% ATM Pressure: 100.0 kPa Test Engineer: Ling Zhu Supervised by: Li Huan Page 2 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.1 20dB Emission Bandwidth Test Result TestMode Antenna Channel 20db EBW[MHz] FL[MHz] FH[MHz] Verdict DH5 Ant 2402 0.915 2401.559 2402.474 --- 2441 1.098 2440.544 2441.486 --- 2480 0.927 2479.544 2480.471 --- 2DH5 Ant 2402 1.284 2401.361 2402.645 --- 2441 1.293 2440.361 2441.654 --- 2480 1.281 2479.361 2480.642 --- 3DH5 Ant 2402 1.299 2401.346 2402.645 --- 2441 1.314 2440.343 2441.657 --- 2480 1.311 2479.340 2480.651 --- Page 3 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs DH5_Ant_2402 DH5_Ant_2441 DH5_Ant_2480 Page 4 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2DH5_Ant_2402 2DH5_Ant_2441 Page 5 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2DH5_Ant_2480 3DH5_Ant_2402 Page 6 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 3DH5_Ant_2441 3DH5_Ant_2480 Page 7 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 8 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.2 Maximum peak conducted output power Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict DH5 Ant 2402 4.47 ≤20.97 PASS 2441 4.59 ≤20.97 PASS 2480 4.94 ≤20.97 PASS 2DH5 Ant 2402 3.35 ≤20.97 PASS 2441 5.96 ≤20.97 PASS 2480 4.9 ≤20.97 PASS 3DH5 Ant 2402 3.35 ≤20.97 PASS 2441 6.07 ≤20.97 PASS 2480 4.84 ≤20.97 PASS Page 9 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs DH5_Ant_2402 DH5_Ant_2441 DH5_Ant_2480 Page 10 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2DH5_Ant_2402 2DH5_Ant_2441 Page 11 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2DH5_Ant_2480 3DH5_Ant_2402 Page 12 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 3DH5_Ant_2441 3DH5_Ant_2480 Page 13 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 14 of 52 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Pa…

Text truncated - open the document above for the full version.

Page 1 of 37 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FOR ALOYS INC. Formuler Z11 Pro Max Test Model: Z11 Pro Max Prepared for : ALOYS INC. Address : #6F ,MARCUS Bldg.,4-5, Yanghyeon-ro405beon-gil,jungwon-gu, Seongnam-si,Gyeonggi-do,South Korea Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : July 01, 2022 Number of tested samples : 2 Sample No. : A062922027-1, A062922027-2 Serial number : Prototype Date of Test : July 01, 2022 ~ July 18, 2022 Date of Report : July 19, 2022 Page 2 of 37 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15 C (15.247) Report Reference No. ................. : LCSA062922027EA Date of Issue ................................... : July 19, 2022 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure ........... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name .......................... : ALOYS INC. Address ........................................... : #6F ,MARCUS Bldg.,4-5, Yanghyeon-ro405beon-gil,jungwon-gu, Seongnam-si,Gyeonggi-do,South Korea Test Specification Standard.......................................... : FCC CFR 47 PART 15 C (15.247) Test Report Form No. ..................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. .................. : Formuler Z11 Pro Max Trade Mark ...................................... : FORMULER Test Model ...................................... : Z11 Pro Max Ratings ............................................ : For Adapter Input: 100-240V~, 50/60Hz For Adapter Output: 12V1.0A Result ........................................... : Positive Compiled by: Supervised by: Approved by: Jack Liu/ Administrator Cary Luo/ Technique principal Gavin Liang / Manager Page 3 of 37 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC -- TEST REPORT Test Model............................... : Z11 Pro Max EUT......................................... : Formuler Z11 Pro Max Applicant............................... : ALOYS INC. Address.................................. : #6F ,MARCUS Bldg.,4-5, Yanghyeon-ro405beon-gil,jungwon-gu, Seongnam-si,Gyeonggi-do,South Korea Telephone............................... : / Fax.......................................... : / Manufacturer........................ : ALOYS INC. Address................................... : #6F ,MARCUS Bldg.,4-5, Yanghyeon-ro405beon-gil,jungwon-gu, Seongnam-si,Gyeonggi-do,South Korea Telephone............................... : / Fax.......................................... : / Factory................................... : Sichuan Changhong Network Technologies Co.,Ltd. Address................................... : G05 Factory Premises, Changhong Intelligent Display Terminal Industrial Park, 38, Xinping Avenue,High-tech District, Mianyang 621000, P. R. China Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCSA062922027EA July 19, 2022 Date of issue Page 4 of 37 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Revision History Report Version Issue Date Revision Content Revised By 000 July 19, 2022 Initial Issue -- Page 5 of 37 FCC ID: 2AV9UFZ105 Report No.: LCSA062922027EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, Chin…

Text truncated - open the document above for the full version.