2AVD2-MH22215Bluetooth headset

Model No.: MH22215 Please read this Quick Start Guide carefully and keep it for future use. QUICK START GUIDE Volume control Turn down the volume: While the music is playing, short press the MFB on the le earphone. Turn up the volume: While the music is playing, short press the MFB on the right earphone. Call Answer/end a call: Double press the MFB . Rejecting a call: Long press 2 seconds the MFB . Music Play/Pause music: Double press the MFB. Previous: While the music is playing, le earphone quickly press 3 times. Next: While the music is playing, right earphone quickly press 3 times. Voice Assistant When the phone is connected, long press the MFB for 2 seconds to wake up the voice assistant. Cautions * Aer removing the earphone from the charging case, there is no need to press any buttons, the le and right earphone will automatically connect and Automatically enter pairing mode. *Please place the earphones in the correct position for charging. *It is not recommended to replace the battery privately without permission. *Batteries [battery packs or cell combinations] must not be exposed to lighting, baking, or similar excessive heat. Indicator/Voice Prompt Guide N-LITE 209 Product Overview In-ear Earphones x 2 (le & right) Charging Case USB-C Charging Cable Quick Start Guide and Warranty Letter Power On/Off Open the cover of the charging case and it will turn on automatically. Put the earphones into the charging case, close the cover, and the earphones will automatically turn off and charge. Charging Use the USB-C charging cable provided with the product to charge. When charging the charging case, the red indicator light on the charging case flashes, and it will stay on aer being fully charged. Pairing Open the charging case cover and the charging case will open automatically. To connect a new device, turn on your phone's Bluetooth and search for "Monster N-Lite 209" to pair.You will hear system prompts aer the earphones are connected to the device. If the earphones have been connected before, they will connect to the last connected device automatically aer being turned on. ModeDescription System tone LED indicator (charging case) - LED indicator (earphone) Reset In the power on state, press the MFB of the earphones 5 times (two earphones at the same time), and the earphones will automatically shut down to reset. Put the earphones in the charging case and then take them out, the earphones will turn on automatically, and enter the pairing mode. Voice prompt Power onThe white light flashes quicklySystem tone Power off The red light is on for 2 secondsSystem tone Connected The white indicator light stays on for 1s and turns off System tone Disconnect The white light flashes quickly Charging The red light flashes slowly when charging, and the red light stays on when it is full -Discharge When the charging case charges the earphones, the white light stays on and turns off when it is full Low battery When open the charging case cover, the red light stays on 1 second and turns off - L/RL/RL/R L/R 1 R LR 1 L 33 2 22 Key operation 1.Multi-function touch button (MFB) 2.USB-C charging interface 3.Charging case indicator light 1 2 3 FCC ID:2AVD2-MH22215

AOGES CO., LIMITED 1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: AOGES CO., LIMITED Contact Name: XIAOYAN LAI Address: Address: 1624 Market St., Ste 226, #30327 Denver CO, 80202 US Telephone No: +1 303 623 1940 Email: [email protected] FRN: 0033947847 Applicant: Company name: Shenzhen Monster Creative Technology Co., Ltd. Product Description: Bluetooth headset FRN: 0036280543 Grantee code: 2AVD2 FCC ID: 2AVD2-MH22215 Contact Name: Wang run long Address: Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, China Telephone No: 86-0755-27364448 Email: [email protected] [Shenzhen Monster Creative Technology Co., Ltd.] certifies that, as of the date of this filing of the application with the TCB, [AOGES CO., LIMITED] is our designated US agent for service of process for the above referenced FCC ID. [Shenzhen Monster Creative Technology Co., Ltd.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [AOGES CO., LIMITED] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 2024.11.25 Applicant’s Name: Shenzhen Monster Creative Technology Co., Ltd. US Agent’s Name: AOGES CO., LIMITED Title: R & D Manager Title: General Manager Signature Signature XIAOYAN LAI

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Shenzhen Monster Creative Technology Co., Ltd. Grantee code: 2AVD2 FRN: 0036280543 FCC ID: 2AVD2-MH22215 Contact Name: Wang run long Address: Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, China Telephone No: 86-0755-27364448 Fax No: Email: [email protected] i. [Shenzhen Monster Creative Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [Shenzhen Monster Creative Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [Shenzhen Monster Creative Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing “covered” equipment. Date: 2024.11.25 Applicant’s Name: Shenzhen Monster Creative Technology Co., Ltd. Title: R & D Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

Shenzhen Monster Creative Technology Co., Ltd Product Similarity Declaration Product name: Bluetooth headset Model name: MH22215, W35 FCC ID: 2AVD2-MH22215 We (Shenzhen Monster Creative Technology Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name Signature: Name: Wang run long Title: Manager China, 2024.11.25

C5266091_X8_Ed.1 1/1 < Shenzhen Monster Creative Technology Co., Ltd. > Letter of Authorization Company: Shenzhen Monster Creative Technology Co., Ltd. Address: Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, China Product Name: Bluetooth headset Model Number: MH22215, W35 FCC Identifier: 2AVD2-MH22215 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Wang run long Date: 2024.11.25 Title: R & D Manager Signature of applicant:

C5266091_X10_Ed.2 1/1 < Shenzhen Monster Creative Technology Co., Ltd. > Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024.11.25 Subject: Request for Confidentiality FCC ID: 2AVD2-MH22215 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, C5266091_X10_Ed.2 1/1 Signature: Name: Wang run long Title: R & D Manager

Page 1 of 7 Report No.: STS2410054 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: MH22215 Photo 1 Photo 2 Page 2 of 7 Report No.: STS2410054 Photo 3 Photo 4 Page 3 of 7 Report No.: STS2410054 Photo 5 Photo 6 Page 4 of 7 Report No.: STS2410054 Photo 7 Photo 8 Page 5 of 7 Report No.: STS2410054 Photo 9 Photo 10 Page 6 of 7 Report No.: STS2410054 Photo 11 Photo 12 Page 7 of 7 Report No.: STS2410054 Photo 13

FCC ID Label Location The product does not have enough space to place the label, and FCC ID label is reflected in the user manual and package, as below: User Manual: Package:

Page 1 of 4 Report No.: STS2410054 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: MH22215 Photo 1 Photo 2 BT ANT Page 2 of 4 Report No.: STS2410054 Photo 3 Photo 4 Page 3 of 4 Report No.: STS2410054 Photo 5 Photo 6 Page 4 of 4 Report No.: STS2410054 Photo 7

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2410054H02 Issued for Shenzhen Monster Creative Technology Co., Ltd. Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Product Name: Bluetooth headset Brand Name: MONSTER Model Name: MH22215 Series Model(s): W35 FCC ID: 2AVD2-MH22215 Test Standards: FCC 47CFR §2.1093 Page 2 of 9 Report No.: STS2410054H02 TEST REPORT Applicant’s Name ................. : Shenzhen Monster Creative Technology Co., Ltd. Address ................................. : Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Manufacturer's Name ........... : Shenzhen Monster Creative Technology Co., Ltd. Address ................................. : Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Product Description Product Name ........................ : Bluetooth headset Brand Name .......................... : MONSTER Model Name .......................... : MH22215 Series Model(s) ...................... : W35 Test Standards ..................... : FCC 47CFR §2.1093 447498 D04 Interim General RF Exposure Guidance v01 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 15 Oct. 2024 Date (s) of performance of tests ............. : 15 Oct. 2024~16 Oct. 2024 Date of Issue .......................................... : 16 Oct. 2024 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Tony Liu) Authorized Signatory : (Bovey Yang) Page 3 of 9 Report No.: STS2410054H02 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 9 Page 4 of 9 Report No.: STS2410054H02 Revision History Rev. Issue Date Report No. Effect Page Contents 00 16 Oct. 2024 STS2410054H02 ALL Initial Issue Page 5 of 9 Report No.: STS2410054H02 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name Bluetooth headset Brand Name MONSTER Model Name MH22215 Series Model(s) W35 Model Difference Only the model name is different Product Description The EUT is Bluetooth headset Operation Frequency: 2402~2480 MHz Modulation Type: BT BR(1Mbps): GFSK BT EDR(2Mbps): π/4-DQPSK BT EDR(3Mbps): 8DPSK Antenna gain: 3dBi Antenna Designation: Ceramic Rating Input: DC 5V 0.5A Battery Rated Voltage:3.7V Charge Limit Voltage:4.2V Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 9 Report No.: STS2410054H02 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS Follow the maximum permissible exposure (MPE) limits specified in 447498 D04 Interim General Radio Frequency Exposure Guidelines v01. The gain of the antenna used in the product was extracted from the supplied antenna data sheet and the maximum total power input to the antenna was also measured. Calculate the distance from the product to the MPE limit by the formula. 2.2 LIMIT For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of Part 1.1307. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: Page 7 of 9 Report No.: STS2410054H02 (C) Or using below table and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). RF Source frequency (MHz) Threshold ERP(watts) 0.3-1.34 1,920 R 2 . 1.34-30 3,450 R 2 /f 2 . 30-300 3.83 R 2 . 300-1,500 0.0128 R 2 f. 1,500-100,000 19.2R 2 . Page 8 of 9 Report No.: STS2410054H02 For multiple RF sources: Multiple RF sources are exempt if: (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging peri…

Text truncated - open the document above for the full version.

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2410054W02 Issued for Shenzhen Monster Creative Technology Co., Ltd. Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Product Name: Bluetooth headset Brand Name: MONSTER Model Name: MH22215 Series Model(s): W35 FCC ID: 2AVD2-MH22215 Test Standards: FCC Part15.247 S T L A B S Page 2 of 95 Report No.: STS2410054W02 TEST REPORT Applicant’s Name ................. : Shenzhen Monster Creative Technology Co., Ltd. Address .................................. : Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Manufacturer's Name ........... : Shenzhen Monster Creative Technology Co., Ltd. Address .................................. : Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Product Description Product Name ........................ : Bluetooth headset Brand Name ........................... : MONSTER Model Name ........................... : MH22215 Series Model(s) .................... : W35 Test Standards...................... : FCC Part15.247 Test Procedure ....................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ............................... : Date of receipt of test item ......... : 15 Oct. 2024 Date (s) of performance of tests : 15 Oct. 2024~16 Oct. 2024 Date of Issue ............................. : 16 Oct. 2024 Test Result ................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Tony Liu) Authorized Signatory : (Bovey Yang) Page 3 of 95 Report No.: STS2410054W02 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 FREQUENCY HOPPING SYSTEM REQUIREMENTS 10 2.4 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 12 2.5 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 2.6 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 13 2.7 EQUIPMENTS LIST 14 3. EMC EMISSION TEST 15 3.1 CONDUCTED EMISSION MEASUREMENT 15 3.2 RADIATED EMISSION MEASUREMENT 19 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 31 4.1 LIMIT 31 4.2 TEST PROCEDURE 31 4.3 TEST SETUP 32 4.4 EUT OPERATION CONDITIONS 32 4.5 TEST RESULTS 32 5. NUMBER OF HOPPING CHANNEL 33 5.1 LIMIT 33 5.2 TEST PROCEDURE 33 5.3 TEST SETUP 33 5.4 EUT OPERATION CONDITIONS 33 5.5 TEST RESULTS 33 6. AVERAGE TIME OF OCCUPANCY 34 6.1 LIMIT 34 6.2 TEST PROCEDURE 34 6.3 TEST SETUP 34 6.4 EUT OPERATION CONDITIONS 34 6.5 TEST RESULTS 34 7. HOPPING CHANNEL SEPARATION MEASUREMEN 35 Page 4 of 95 Report No.: STS2410054W02 Table of Contents Page 7.1 LIMIT 35 7.2 TEST PROCEDURE 35 7.3 TEST SETUP 35 7.4 EUT OPERATION CONDITIONS 35 7.5 TEST RESULTS 35 8. BANDWIDTH TEST 36 8.1 LIMIT 36 8.2 TEST PROCEDURE 36 8.3 TEST SETUP 36 8.4 EUT OPERATION CONDITIONS 36 8.5 TEST RESULTS 36 9. OUTPUT POWER TEST 37 9.1 LIMIT 37 9.2 TEST PROCEDURE 37 9.3 TEST SETUP 38 9.4 EUT OPERATION CONDITIONS 38 9.5 TEST RESULTS 38 10. ANTENNA REQUIREMENT 39 10.1 STANDARD REQUIREMENT 39 10.2 EUT ANTENNA 39 APPENDIX 1-TEST DATA 40 1. DWELL TIME 40 2. MAXIMUM PEAK CONDUCTED OUTPUT POWER 50 3. -20DB BANDWIDTH 56 4. CARRIER FREQUENCIES SEPARATION 62 5. NUMBER OF HOPPING CHANNEL 68 6. BAND EDGE 71 7. BAND EDGE(HOPPING) 78 8. CONDUCTED RF SPURIOUS EMISSION 85 APPENDIX 2-PHOTOS OF TEST SETUP 95 Page 5 of 95 Report No.: STS2410054W02 Revision History Rev. Issue Date Report No. Effect Page Contents 00 16 Oct. 2024 STS2410054W02 ALL Initial Issue Page 6 of 95 Report No.: STS2410054W02 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247(a)(1) Hopping Channel Separation PASS -- 15.247(a)(1)&(b)(1) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247(d) Conducted Spurious & Band Edge Emission PASS -- 15.247(a)(1)(iii) Number of Hopping Frequency PASS -- 15.247(a)(1)(iii) Dwell Time PASS -- 15.247(a)(1) Bandwidth PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Page 7 of 95 Report No.: STS2410054W02 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.755dB 2 Unwanted Emissions, conducted ±2.874dB 3 All emissions, radiated 9K-30MHz ±3.80dB 4 All emissions, radiated 30M-1GHz ±4.18dB 5 All emissions, radiated 1G-6GHz ±4.90dB 6 All emissions, radiated>6G ±5.24dB 7 Conducted Emission (9KHz-150KHz) ±2.19dB 8 Conducted Emission (150KHz-30MHz…

Text truncated - open the document above for the full version.

SymbolsLWTA Dimensions 1.60±0.200.80±0.200.80±0.200.30±0.10 NumberTerminalName ① INPUT ② NC Dimensions(Unit: mm) w ①② ( Side View) ( Bottom View) ( Top View) A T L HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page1 HanyangAntenna Design Co. Ltd. Applications 1.Bluetooth 2.WirelessLAN 3.ISM band 2.4GHz wirelessapplications Features 1.Surfacemounteddeviceswithasmalldimensionof1.6×0.8×0.8mmmeetfutureminiaturization trend. 2.EmbeddedandLTCC(lowtemperatureco-firedceramic)technologyisabletointegratewith systemdesignaswellasbeatifyingthehousingoffinalproduct. 3.Highstabilityandlowtolerance. P/N:HY160808 SRF07 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City MatchingCircuits P/N:HY160808 SRF07 HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page2 1 W=2 1 W2=2 1.5 Feeding line 2 5 0201/0402 footprint 0603 footprint 0201/0402 footprint 0.5 Unit:mm 2 L=4 W1 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City Application example-1 P/N:HY160808 SRF07 HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page3 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City Application example-2 P/N:HY160808 SRF07 HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page4 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City ElectricalCharacteristics CharacteristicCurves FeatureSpecification 1 Centralfrequency 2.45GHz 2 Bandwidth100MHz 3 Peak gain3dBi 4 VSWR<2 5 PolarizationLinear 6 AzimuthbeamwidthOmnidirectional 7 Impedance50Ω P/N:HY160808 SRF07 HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page5 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City RadiationPattern Y-ZPlane X-ZPlane coordinates： HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page6 P/N:HY160808 SRF07 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City Unit: dBi Unit: dBi 2450 MHZ 2450 MHZ 3D RadiationPattern Frequency 2450MHz Avg.gain-0.85dBi Peakgain3.0dBi Efficiency82% HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page7 P/N:HY160808 SRF07 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City Unit: dBi 2450 MHZ 2450 MHZ Temperature：40±2°C Humidity：90~95%RH Duration：500h Recovery conditions：Room temperature Recovery Time：24h (Class1) or 48h (Class2) Test Temperature Operating Temperature Temperature RelativeHumidity 25°C±3°C -25°C~+85°C 5~40°C 20~70% Notenoughsolder Weak holding forcemay cause bad connection between the chipandPCB. RecommendedSolderingAmounts The optimal solder fillet amounts forre-flowsoldering 天线厚度 以下 The optimal solder fillet amounts for wavesoldering DependabilityTest Too much solder Cracks tend to occur due to large stress. MoistureProof OptimumSolderAmount forReflowSoldering Solderability At least 95% of the terminal electrode is covered by newsolder. Preheating conditions:80 to 120°C;10~30s. Solder Tem p e r at u r e :2 3 5 ±5°C Duration:2 ±0.5s , Solder Tempe r ature:24 5±5°C Du rat ion:2±0.5s HanyangAntennaDesignCo.Ltd.haspossessionofproprietaryinformationprovidedinthisreportand thisproprietaryinformationshallbekeptinstrictconfidenceandnotdisclosedtoanypersonorfirm withoutthepriorwrittenconsentofHanyangAntennaDesignCo.Ltd. Page8 P/N:HY160808 SRF07 HanyangAntenna Design Co. Ltd. 12A11 Baoyunda Logistics Information Building, Qianjin 2nd Road, Bao'an District, Shenzhen Room 606, Building A1, Hisense Industrial Park, No. 399 Songling Road, Laoshan District, Qingdao City 10±1S AppliedForce:5NDuration:10±1S Preheating conditions: up-category temperature, 1h Recovery time:24±…

Text truncated - open the document above for the full version.