2AVD2-MH22261BLUETOOTH HEADPHONE

Charge Before using "Monster Airclip AC200" , please connect the USB-C cable to a power adapter to begin charging. Fully charge the earphones and the charging case before the first use. Power On/Off Open the cover of the charging case ,the earphones will turn on automatically. If you want to turn off the earphones, please put the earphones into the charging case and close the cover,the earphones will power off and charge at the same time. Pairing Open the cover of the charging case ,the earphones will turn on automatically.For new device connection, turn on the Bluetooth Model No.: MH22261 封面 Please read this Quick Start Guide carefully and keep it for future use. QUICK START GUIDE in your device and choose "Monster Airclip AC200" from the Bluetooth list to connect. You will hear system prompts aer the earphones are connected to the device. If the earphones have been paired before, they will automatically reconnect to the previous device when turned on. Wearing Put the "Monster Airclip AC200" onto your ears and rotate to fit comfortably to get the best wearing and sound quality experience. 充电 在使用"Monster Airclip AC200" 之前，请在使用此设备前先给耳 机和充电仓充满电，此设备可以通过USB-C接口进行充电。 电源开、关 打开充电盒盖，耳机将自动开机。如果想要关闭耳机，请将耳机放入充电 盒合盖，耳机会关机同时进行充电。 配对 打开充电盒，耳机将自动开机。对于新设备连接，请打开蓝牙设备并搜索 "Monster Airclip AC200" 进行连接，配对成功后，您会听到系统提 示音。 如果耳机之前已配对过，开机自动回连上一次的设备。 佩戴 拿出耳机，将"Monster Airclip AC200" 顺着耳后佩戴，并轻轻旋 转至舒适位置，以确保获得最佳的佩戴效果和音质体验。 恢复出厂设置 开机状态下连续5击耳机触控键（双耳同时），耳机自动关机复位；耳 机入仓合盖，当仓盖再次打开时耳机会重新开机，进入配对模式。 产品概述 注意 *不建议未经许可私下更换电池。 *电池[电池组或电池组合]不得暴露在照明，烘烤或类似过热的环境中。 *耳机充电仓在外接电源充电时，输入电压电流标准≤ 5V/1A； Attention *Private replacement of batteries without permission is not recommended. *Batteries [battery packs or battery combinations] should not be exposed to lighting, baking or similar overheating environments. *The input voltage and current standard ≤ 5V/1A when charging the headset charging compartment from an external power source; 更多操作 按键操作 接听 挂断 拒接 LED 指示灯（耳机） 开机 关机 配对成功 配对超时 连接超距 断开手机连接 低电提醒 低电关机 LED 指示灯（充电盒） 充电 放电 低电提醒 双击左或右耳 双击左或右耳 长按左或右耳 白灯闪 红灯长亮2s熄灭 白灯长亮1s熄灭 红灯长亮2s熄灭 白灯快闪 白灯快闪 红灯慢闪 红灯长亮2s熄灭 红灯持续慢闪,充满红灯长亮 仓给耳机充电时白灯长亮，充满熄灭 红灯闪烁 Additional Operation 请仔细阅读本快速指南并妥善保存以备将来使用。 快速指南 耳机x2 (左&右耳）充电盒x1 USB-C充电线 x1 快速指南/保修卡 USB-C Port Reset In the power on state, touch the MFB of the earphones 5 times (two earphones at the same time),the earphones will automatically shut down and put the earphones into the charging case. When the cover is opened again, the earphone will turn on again and enter the pairing mode. MFB OperationProduct Overview Open earphones x2 (L & R） Charging case x1 USB-C cable x1 Quick start guide and warranty card AIRCLIP AC200 Answer call End call Reject call LED indicator (earphone) Power on Power off Pairing is successful Pairing timed out Connection is over distance Disconnect the phone Low battery Low power off LED indicator (charging case) Charging Discharge Low battery Press L or R twice Press L or R twice Long press le or right ear White light flashing The red light on 2s and then turn off The white light on 1s and then turn off The red light on 2s and then turn off White flashes White flashes Red light flashes slowly The red light on 2s and then turn off The red light continues to flash slowly, and the red light is full and on When the charging case charges the earphones, the white light stays on and turns off when it is full Red flashes 本产品由中国平安保险公司承保 Model No.: MH22261 1 2 3 4 L/R L R L/RL/R L/R L R 2 11 33 2s 2s 2 75X95MM 105G双胶+4C+186C印刷+风琴折 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio / TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: 2AVD2-MH22261 FCC STATEMENT USB-C 接口处 1 2 3 4 L/R L R L/RL/R L/R L R 2 11 33 2s 2s 2 X:表示该有害物质至少 在该部件的某一均质材料中的含量超出G B/T�� ���规定的限量要求。 本表格依据SJ /T�����- ����的规定来编制 O: 表示该有害物质在该部件所有均质材料中的含量均在G B/T�� ���规定的限量要求以 下。 产品有毒有害物质或元素表 有害物质 铅 (Pb) 汞 (Hg) 镉 (Cd) 六格铬 (Cr(VI)) 多溴联笨 (PBBs) 多溴二笨醚 (PBDEs) 部件名称 外壳线材喇叭主板 ○○○○ ○○○○ ○○○○ ○○○○ ○○ ○ ○ ○○○○ 电池 X ○ ○ ○ ○ ○ 保修信息卡 信息填写 产品名称： 产品型号： 产品SN号： 购机日期： 用户信息 用户姓名： 联系电话： 地 址： IC CAUTION Radio Standards Specification RSS-Gen, issue 5 - English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interfer…

Text truncated - open the document above for the full version.

* theapplicantmustdesignateacontactlocatedintheUnitedStatesforpurposesofactingasthe applicant’sagentforserviceofprocess,regardlessofwhethertheapplicantisadomesticorforeign entity.AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforserviceofprocess. SC5084775 U.S.AgentDesignationforServiceofProcess- CertificationAttestationLetter 9/4/2025 TO:FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 ATTN.:ReviewingEngineer FCCID:2AVD2-MH22261 FRNofapplicant:0036280543 Persection2.911(d)(7)oftheFCCrules,[ShenzhenMonsterCreativeTechnologyCo.,Ltd.] (“theapplicant”)certifiesthattheequipmentforwhichauthorizationissoughtisdesignatedto thefollowingU.S.agent*forserviceofprocess: CompanyName:GlobalProductServicesandConsultationLLC FCCRegistrationNumber(FRN):0033406703 PhysicalU.S.CompanyAddress:328WPalmAve.,Monrovia,CA91016,UnitedStates ContactPerson:MichaelChan AgentEmailAddress:[email protected] Theabovecontactpersonacceptstheobligationforserviceofprocess. Theapplicantacceptstomaintainanagentfornolessthanoneyearafterthegranteehas terminatedallmarketingandimportationortheconclusionofanyCommission-related proceedinginvolvingtheequipment. ApplicantSigned:AgentSigned(ifdifferentfromApplicant): Signed: Printedname:runlongwang Title:R&DManager CompanyName:ShenzhenMonsterCreative TechnologyCo.,Ltd. Address:Room1602,BuildingA,Fencheng ZhiguBuilding,XixiangStreet,Bao'anDistrict, Shenzhen,Guangdong,518126,China Signed: Printedname:MichaelChan Title:TechnicalDirector CompanyName:GlobalProductServicesand ConsultationLLC Date:9/4/2025 Date:9/2/2025

Shenzhen Monster Creative Technology Co., Ltd. (2025-09-02) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2AVD2-MH22261) [Shenzhen Monster Creative Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, run long wang R & D Manager Shenzhen Monster Creative Technology Co., Ltd. Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Shenzhen Monster Creative Technology Co., Ltd. (2025-09-02) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2AVD2-MH22261) [Shenzhen Monster Creative Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, run long wang R & D Manager Shenzhen Monster Creative Technology Co., Ltd. Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China

External Photographs View of EUT-1 View of EUT-2 Page 2 of 10 View of EUT-3 View of EUT-4 Page 3 of 10 View of EUT-5 View of EUT-6 Page 4 of 10 View of EUT-7 View of EUT-8 Page 5 of 10 View of EUT-9 View of EUT-10 Page 6 of 10 View of EUT-11 View of EUT-12 Page 7 of 10 View of EUT-13 View of EUT-14 Page 8 of 10 View of EUT-15 View of EUT-16 Page 9 of 10 View of EUT-17 View of EUT-18 Page 10 of 10 View of EUT-19

丝印金色 丝印银色 丝印金色 丝印银色 30.00 mm 2.69 mm 30.00 mm 2.69 mm 5.00 mm 3.49 mm 5.00 mm 3.49 mm 位置:上盖反面 镭雕信息 镭雕动态SN号码 颜色：本色 尺寸：41.3x11.8mm SN:生产自行更新， 以生产日期为准 产品必须三码合一， 机身彩盒外箱一一对应 序列号以交货时间 来控制丝印的数量跟印刷日期 八月交货 801 九月交货 901 十月交货 A01 十一月交货 B01 十二月交货 C01 请勿跨月 序列号 SN: MH22261 25401 00001 DESIGNED IN CALIFORNIA MADE IN CHINA Shenzhen Monster Creative Technology Co., Ltd SN: MH222612540100001 BLUETOOTH HEADPHONE Model: MH22261 Input: 5V 0.5A CMIIT ID:25J44T9X9833 FCC ID: 2AVD2-MH22261 IC: 28087-MH22261 5.3mm6mm 41.3mm 11.8mm 3mm 位置:上盖反面 镭雕信息 镭雕动态SN号码 颜色：本色 尺寸：41.3x11.8mm SN:生产自行更新， 以生产日期为准 产品必须三码合一， 机身彩盒外箱一一对应 序列号以交货时间 来控制丝印的数量跟印刷日期 八月交货 801 九月交货 901 十月交货 A01 十一月交货 B01 十二月交货 C01 请勿跨月 序列号 SN: MH22261 25401 00001 DESIGNED IN CALIFORNIA MADE IN CHINA Shenzhen Monster Creative Technology Co., Ltd SN: MH222612540100001 BLUETOOTH HEADPHONE Model: MH22261 Input: 5V 0.5A CMIIT ID:25J44T9X9833 FCC ID: 2AVD2-MH22261 IC: 28087-MH22261 5.3mm6mm 41.3mm 11.8mm 3mm IC IC 28087-MH22261 28087-MH22261

Internal Photographs Internal View of EUT-1 Internal View of EUT-2 Page 2 of 12 Internal View of EUT-3 Internal View of EUT-4 Page 3 of 12 Internal View of EUT-5 Internal View of EUT-6 Page 4 of 12 Internal View of EUT-7 Internal View of EUT-8 Page 5 of 12 Internal View of EUT-9 Internal View of EUT-10 Page 6 of 12 Internal View of EUT-11 Internal View of EUT-12 Antenna Page 7 of 12 Internal View of EUT-13 Internal View of EUT-14 Page 8 of 12 Internal View of EUT-15 Internal View of EUT-16 Page 9 of 12 Internal View of EUT-17 Internal View of EUT-18 Page 10 of 12 Internal View of EUT-19 Internal View of EUT-20 Page 11 of 12 Internal View of EUT-21 Internal View of EUT-22 Page 12 of 12 Internal View of EUT-23

RF EXPOSURE EVALUATION EUT Specification FCC ID 2AVD2-MH22261 EUT Name BLUETOOTH HEADPHONE Model MH22261 Series Model E1116, MH22269 Model Difference Note: Only the model names are different. Antenna gain (Max) 2.7 dBi Operation Frequency 2402-2480MHz Classification Per Stipulated Test Standard §15.247(i), §2.1093 Modulation GFSK, π/4-DQPSK, 8DPSK Max. output power -2.27 dBm(0.593mW) Test Requirement: According to ß15.247(i) and ß1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Routine SAR evaluation refers to that specifically required by ß2.1093, using measurements or computer simulation. When routine SAR evaluation is not required, portable transmitters with output power greater than the applicable low threshold require SAR evaluation to quality for TCB approval. One antenna is available for the EUT. The minimum separation distance is 5mm. Transmit Frequency (MHz) Mode Measured Power (dBm) Tune up Power (dBm) Max tune up power(dBm) Calculation Result 1-g SAR Verdict 2480 3DH5 -2.27 -2±1 -1 0.250182 3 PASS Note: No need for SAR test Signature: Shawn Wen Date: 2025-07-05

2.4GHz 3216 Chip Antenna: RANT3216F245X07 _ Application: WLAN,802.11b/g,Bluetooth,WLAN,etc... Features SMD,highreliability,ultraImpact,Omni-directional... PartnumberInformation RANT3216F24507 (A)(B)(C)(D)(F X (E)) ElectricalSpecification DimensionandTerminalConfiguration No.TerminalName 1Feeding/GNG 2GND/Feeding (A)ProductTypeChipAntenna (B)SizeCode 3.2x1.6mm( ± 0.2mm) (C)MaterialHighKmaterial (D)Frequency2.4~2.5GHz (E)FeedingmodePIFA&SingleFeeding (F)AntennatypeType=07 WorkingFrequencyRange2400~2500MHz Bandwidth120MHz(Min.) PeakGain2.7 dBi (Typ.) Impedance50Ohm Returnloss10dB(Min) PolarizationLinear AzimuthBeamwidthOmni-directional OperationTemperature( °C )-40~85 °C ResistancetoSolderingHeats 10sec.(@280 °C ) TerminationNi/Au(Leadless) Dimension(mm) L 3.20±0.20 W 1.60±0.20 T 0.85±0.20 Room 707, Building F, Tongan Zhichuangyuan, xixiang street, Baoan District, Shenzhen. 2.4GHz 3216 Chip Antenna: RANT3216F245X07 _ 1 EvaluationBoardReference PCBDimensionAntennaLayoutReference Unit:mm ElectricalCharacteristics ReturnLoss&Radiation ReturnLoss Frequency(MHz) S11(dB) 2400-10.50 2450-30.62 2500-11.47 Radiation 2400MHz2450MHz2500MHz Efficiency82.52%85.26%83.01% X Y Z Room 707, Building F, Tongan Zhichuangyuan, xixiang street, Baoan District, Shenzhen. 2.4GHz 3216 Chip Antenna: RANT3216F245X07 _ TapingSpecifications ReelandTapingSpecification ReelSpecification TYPESIZEABCD 32167”4K/Reel 9.0±0.5 60±213.5±0.5178±2 TappingSpecification PackagingTypeABWEFGHTψDP PaperType3216 1.90±0.203.50±0.208.0±0.201.75±0.103.5±0.054.0±0.102.0±0.050.75±0.10 1.50±0.10 4.0±0.1 Room 707, Building F, Tongan Zhichuangyuan, xixiang street, Baoan District, Shenzhen. _ 2.4GHz 3216 Chip Antenna: RANT3216F245X07 Reliability Table TestItemProcedure Requirements CeramicType Remark (Reference) Electrical Characterization Fulfilltheelectrical specification UserSpec. Thermal Shock 1.Preconditioning: 50±10°C/1hr,thenkeepfor24±1hrsatroomtemp. 2.Initialmeasure:Spec:referInitialspec. 3.Rapidchangeoftemperaturetest: -30°Cto+85°C;100cycles; 15minutesatLowercategorytemperature; 15minutesatUppercategorytemperature. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 107 Temperature Cycling 1.Initialmeasure:Spec:referInitialspec. 2.100Cycles(-30°Cto+85°C),SoakMode=1(2Cycle/hours). 3.Measurementat24±2Hoursaftertestcondition. NoVisibleDamage. Fulfilltheelectrical specification. JESD22 JA104 HighTemperature Exposure 1.Initialmeasure:Spec:referInitialspec. 2.Unpowered;500hours@T=+85°C. 3.Measurementat24±2hoursaftertest. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 108 LowTemperature Storage 1.Initialmeasure:Spec:referInitialspec. 2.Unpowered:500hours@T=-30°C. 3.Measurementat24±2hoursaftertest. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 108 Solderability (SMDBottomSide) Dippingmethod: a.Temperature:235±5°C b.Dippingtime:3±0.5s Thesoldershouldcover over95%ofthecritical areaofbottomside. IEC60384-21/22 4.10 SolderingHeat Resistance (RSH) Preheatingtemperature:150±10°C. Preheatingtime:1~2min. Soldertemperature:260±5°C. Dippingtime:5±0.5s NoVisibleDamage.IEC60384-21/22 4.10 Vibration5g'sfor20min.,12cycleseachof3orientations Note:Use8"X5"PCB.031"thick7securepointson,onelong sideand2securepointsatcornersofoppositesides.Parts mountedwithin2"fromanysecurepoint.Testfrom10-2000 Hz. NoVisibleDamage.MIL-STD-202 Method204 Mechanical Shock Threeshocksineachdirectionshallbeappliedalongthethree mutuallyperpendicularaxesofthetestspecimen(18shocks) Peakvalue:1,500g’s Duration:0.5ms Velocitychange:15.4ft/s Waveform:Half-sine NoVisibleDamage.MIL-STD-202 Method213 Humidity Bias 1.Humidity:85%R.H.,Temperature:85±2°C. 2.Time:500±24hours. 3.Measurementat24±2hrsaftertestcondition. NoVisibleDamage. Fulfilltheelectrical specification. MIL-STD-202 Method106 Room 707, Building F, Tongan Zhichuangyuan, xixiang street, Baoan District, Shenzhen. 2.4GHz 3216 Chip Antenna: RANT3216F245X07 _ Board Flex (SMD) 1.Mountingmethod: IR-Reflow.PCBSize(L:100×W:40×T:1.6mm) 2.Applytheloadindirectionofthearrowuntilbendingreaches 2mm. NoVisibleDamage.AEC-Q200 005 AdhesionForceof1.8Kgfor60seconds.NoVisibleDamage Magnificationof20Xor greatermaybeemployed forinspectionofthe mechanicalintegrityofthe devicebodyterminalsand body/terminaljunction. AEC-Q200 006 Physical Dimension Anyapplicablemethodusingx10magnification,micrometers, calipers,gauges,contourprojectors,orothermeasuring equipment,capableofdeterminingtheactualspecimen dimensions. Inaccordancewith specification. JESD22 JB100 RevisionHistory RevisionDateContent 12019/03/01NewDatasheet 2Add2Dradiationcharacteristi2022/02/22c Room 707, Building F, Tongan Zhichuangyuan, xixiang street, Baoan District, Shenzhen.

TRF No.: 04-E001-0B TRF Originator: GTG TRF Date: 2023-12-13 Web: www.gtggroup.com E-mail: [email protected] Tel.: 86-400 755 8988 CFR 47 FCC PART 15 SUBPART C TEST REPORT For BLUETOOTH HEADPHONE MODEL NUMBER: MH22261, E1116, MH22269 REPORT NUMBER: E04A25061461F00101 ISSUE DATE: July 4, 2025 FCC ID: 2AVD2-MH22261 Prepared for Shenzhen Monster Creative Technology Co., Ltd. Room 1602, Building A, Fencheng Zhigu Building, Xixiang Street, Bao 'an District, Shenzhen, Guangdong, 518126, China Prepared by Guangdong Global Testing Technology Co., Ltd. Room 101-105, 203-210, Building 1, No.2, Keji 8 Road, Songshan Lake Park, Dongguan city, Guangdong, People’s Republic of China, 523808 This report is based on a single evaluation of the submitted sample(s) of the above mentioned product, it does not imply an assessment of the production of the products. This report shall not be reproduced, except in full, without the written approval of Guangdong Global Testing Technology Co., Ltd. REPORT NO.: E04A25061461F00101 Page 2 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Revision History Rev. Issue Date Revisions Revised By V0 July 4, 2025 Initial Issue REPORT NO.: E04A25061461F00101 Page 3 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Summary of Test Results Test Item Clause Limit/Requirement Result Antenna Requirement N/A FCC Part 15.203/15.247 (c) Pass AC Power Line Conducted Emission ANSI C63.10-2013 Clause 6.2 FCC Part 15.207 Pass Conducted Output Power ANSI C63.10-2013 Clause 7.8.5 FCC Part 15.247 (b)(1) Pass 20 dB Bandwidth ANSI C63.10-2013 Clause 6.9.2 FCC Part 15.247 (a)(1) Pass Carrier Hopping Channel Separation ANSI C63.10-2013 Clause 7.8.2 FCC Part 15.247 (a)(1) Pass Number of Hopping Frequency ANSI C63.10-2013 Clause 7.8.3 FCC Part 15.247 (b)(1) Pass Time of Occupancy (Dwell Time) ANSI C63.10-2013 Clause 7.8.4 FCC Part 15.247 (a)(1) Pass Conducted Bandedge and Spurious Emission ANSI C63.10-2013 Clause 6.10.4 & Clause 7.8.8 FCC Part 15.247(d) Pass Radiated Band edge and Spurious Emission ANSI C63.10-2013 Clause 6.3 & 6.5 & 6.6 FCC Part 15.205/15.209 Pass Duty Cycle ANSI C63.10-2013, Clause 11.6 None; for reporting purposes only. Pass *This test report is only published to and used by the applicant, and it is not for evidence purpose in China. *The measurement result for the sample received is <Pass> according to <CFR 47 FCC PART 15 SUBPART C)> when <Accuracy Method> decision rule is applied. REPORT NO.: E04A25061461F00101 Page 4 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................... 5 2. TEST METHODOLOGY ......................................................................................................... 6 3. FACILITIES AND ACCREDITATION ..................................................................................... 6 4. CALIBRATION AND UNCERTAINTY ................................................................................... 7 4.1. MEASURING INSTRUMENT CALIBRATION ........................................................... 7 4.2. MEASUREMENT UNCERTAINTY ............................................................................ 7 5. EQUIPMENT UNDER TEST .................................................................................................. 8 5.1. DESCRIPTION OF EUT ........................................................................................... 8 5.2. CHANNEL LIST ........................................................................................................ 8 5.3. MAXIMUM PEAK OUTPUT POWER ........................................................................ 9 5.4. TEST CHANNEL CONFIGURATION ........................................................................ 9 5.5. THE WORSE CASE POWER SETTING PARAMETER ............................................ 9 5.6. DESCRIPTION OF AVAILABLE ANTENNAS ......................................................... 10 5.7. SUPPORT UNITS FOR SYSTEM TEST ................................................................. 10 5.8. SETUP DIAGRAM .................................................................................................. 11 6. MEASURING EQUIPMENT AND SOFTWARE USED......................................................... 12 7. ANTENNA PORT TEST RESULTS ..................................................................................... 14 7.1. Conducted Output Power ........................................................................................ 14 7.2. 20 dB Bandwidth ..................................................................................................... 15 7.3. Carrier Hopping Channel Separation ...................................................................... 16 7.4. Number of Hopping Frequency ............................................................................... 18 7.5. Time of Occupancy (Dwell Time) ............................................................................ 19 7.6. Conducted Bandedge and Spurious Emission ........................................................ 21 7.7. Duty Cycle .............................................................................................................. 23 8. RADIATED TEST RESULTS ............................................................................................... 24 8.1. Radiated Band edge and Spurious Emission .......................................................... 30 9. ANTENNA REQUIREMENT ................................................................................................ 42 10. AC POWER LINE CONDUCTED EMISSION ......................................................... 43 11. TEST DATA - Appendix A ..................................................................................... 46 REPORT NO.: E04A25061461F00101 Page 5 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. 1. ATTESTATION OF TEST RESULTS Applic…

Text truncated - open the document above for the full version.

REPORT NO.: E04A25061461F00101 Page 61 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. CFS NVNT 2-DH5 2441MHz Ant1 CFS NVNT 2-DH5 2480MHz Ant1 REPORT NO.: E04A25061461F00101 Page 62 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. CFS NVNT 3-DH5 2402MHz Ant1 CFS NVNT 3-DH5 2441MHz Ant1 REPORT NO.: E04A25061461F00101 Page 63 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. CFS NVNT 3-DH5 2480MHz Ant1 REPORT NO.: E04A25061461F00101 Page 64 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Number of Hopping Channel Condition Mode Antenna Hopping Number Limit Verdict NVNT 1-DH5 Ant1 79 15 Pass NVNT 2-DH5 Ant1 79 15 Pass NVNT 3-DH5 Ant1 79 15 Pass REPORT NO.: E04A25061461F00101 Page 65 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Test Graphs Hopping No. NVNT 1-DH5 2402MHz Ant1 Hopping No. NVNT 2-DH5 2402MHz Ant1 REPORT NO.: E04A25061461F00101 Page 66 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Hopping No. NVNT 3-DH5 2402MHz Ant1 REPORT NO.: E04A25061461F00101 Page 67 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell Time Condition Mode Frequency (MHz) Antenna Pulse Time (ms) Total Dwell Time (ms) Burst Count Period Time (ms) Limit (ms) Verdict NVNT 1-DH5 2402 Ant1 2.907 305.235 105 31600 400 Pass NVNT 1-DH5 2441 Ant1 2.905 299.215 103 31600 400 Pass NVNT 1-DH5 2480 Ant1 2.905 316.645 109 31600 400 Pass NVNT 2-DH5 2402 Ant1 2.907 311.049 107 31600 400 Pass NVNT 2-DH5 2441 Ant1 2.911 317.299 109 31600 400 Pass NVNT 2-DH5 2480 Ant1 2.91 314.28 108 31600 400 Pass NVNT 3-DH5 2402 Ant1 2.917 338.372 116 31600 400 Pass NVNT 3-DH5 2441 Ant1 2.913 352.473 121 31600 400 Pass NVNT 3-DH5 2480 Ant1 2.914 335.11 115 31600 400 Pass REPORT NO.: E04A25061461F00101 Page 68 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Test Graphs Dwell NVNT 1-DH5 2402MHz Ant1 One Burst Dwell NVNT 1-DH5 2402MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 69 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 1-DH5 2441MHz Ant1 One Burst Dwell NVNT 1-DH5 2441MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 70 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 1-DH5 2480MHz Ant1 One Burst Dwell NVNT 1-DH5 2480MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 71 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 2-DH5 2402MHz Ant1 One Burst Dwell NVNT 2-DH5 2402MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 72 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 2-DH5 2441MHz Ant1 One Burst Dwell NVNT 2-DH5 2441MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 73 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 2-DH5 2480MHz Ant1 One Burst Dwell NVNT 2-DH5 2480MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 74 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 3-DH5 2402MHz Ant1 One Burst Dwell NVNT 3-DH5 2402MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 75 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 3-DH5 2441MHz Ant1 One Burst Dwell NVNT 3-DH5 2441MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 76 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Dwell NVNT 3-DH5 2480MHz Ant1 One Burst Dwell NVNT 3-DH5 2480MHz Ant1 Accumulated REPORT NO.: E04A25061461F00101 Page 77 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge Condition Mode Frequency (MHz) Antenna Hopping Mode Max Value (dBc) Limit (dBc) Verdict NVNT 1-DH5 2402 Ant1 No-Hopping -51.12 -20 Pass NVNT 1-DH5 2480 Ant1 No-Hopping -52.44 -20 Pass NVNT 2-DH5 2402 Ant1 No-Hopping -51.74 -20 Pass NVNT 2-DH5 2480 Ant1 No-Hopping -52.16 -20 Pass NVNT 3-DH5 2402 Ant1 No-Hopping -51.11 -20 Pass NVNT 3-DH5 2480 Ant1 No-Hopping -51.96 -20 Pass REPORT NO.: E04A25061461F00101 Page 78 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Test Graphs Band Edge NVNT 1-DH5 2402MHz Ant1 No-Hopping Ref Band Edge NVNT 1-DH5 2402MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 79 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge NVNT 1-DH5 2480MHz Ant1 No-Hopping Ref Band Edge NVNT 1-DH5 2480MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 80 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge NVNT 2-DH5 2402MHz Ant1 No-Hopping Ref Band Edge NVNT 2-DH5 2402MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 81 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge NVNT 2-DH5 2480MHz Ant1 No-Hopping Ref Band Edge NVNT 2-DH5 2480MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 82 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge NVNT 3-DH5 2402MHz Ant1 No-Hopping Ref Band Edge NVNT 3-DH5 2402MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 83 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge NVNT 3-DH5 2480MHz Ant1 No-Hopping Ref Band Edge NVNT 3-DH5 2480MHz Ant1 No-Hopping Emission REPORT NO.: E04A25061461F00101 Page 84 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge(Hopping) Condition Mode Frequency (MHz) Antenna Hopping Mode Max Value (dBc) Limit (dBc) Verdict NVNT 1-DH5 2402 Ant1 Hopping -49.78 -20 Pass NVNT 1-DH5 2480 Ant1 Hopping -51.51 -20 Pass NVNT 2-DH5 2402 Ant1 Hopping -50.36 -20 Pass NVNT 2-DH5 2480 Ant1 Hopping -51.61 -20 Pass NVNT 3-DH5 2402 Ant1 Hopping -49.34 -20 Pass NVNT 3-DH5 2480 Ant1 Hopping -49.89 -20 Pass REPORT NO.: E04A25061461F00101 Page 85 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Test Graphs Band Edge(Hopping) NVNT 1-DH5 2402MHz Ant1 Hopping Ref Band Edge(Hopping) NVNT 1-DH5 2402MHz Ant1 Hopping Emission REPORT NO.: E04A25061461F00101 Page 86 of 100 TRF No.: 04-E001-0B Global Testing , Great Quality. Band Edge(Hopping) NVNT 1-DH5 2480MHz Ant1 Hopping Ref Band Edge(Hopping) NVNT 1-DH5 2480MHz Ant1 Hopping Emission REPORT NO.: E04A25061461F0010…

Text truncated - open the document above for the full version.

Setup Photographs AC Power Line Conducted Emission Radiated Band edge and Spurious Emission Page 2 of 3 Page 3 of 3