2AYYSZEAW01BApple Watch USB-Stick Wireless Charger

- 2 - NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC radiated Exposure Statement: This devices complies with FCC radiated exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located operating in conjunction with any other antenna or transmitter. During operation the user must keep a minimum separation distance of 10 cm with RF devices. - 3 - GB In the packaging • ZENS Apple Watch USB-stick • User manual • Extended warranty registration card Quick start in 2 steps Compatibility The ZENS Apple Watch USB-stick is made for the Apple Watch (all series) and works with all USB-A ports. It can be plugged in to any USB-A port (e.g. in a laptop, powerbank, adapter, etc.) in order to charge the Apple Watch. ZENS Wireless Charging Important safety notices • Keep the product away from water. • Do not place or store the product near water or any other liquid. • After cleaning, make sure the product is completely dry before you connect it to an electrical socket - 4 - Warning notifications • Check if the voltage indicated on the power adaptor or power plug corresponds to the local voltage before you connect the adapter to a power outlet. • Never use the charger, power adapter, power plug or USB cable if any of them is damaged in any way. • Only use the official power adapter, power plug or USB cable (supplied together with the charger). When an unofficial power adapter is used or an incorrect voltage us used for the charger, the light with blink rapidly and no charging will occur. • Do not place any metallic labels or any objects onto the charger. • Do not use the charger outdoors or near heated surfaces. • If you have a pacemaker or other implanted device, consult your doctor or the manufacturer of the implanted device before using the charger. • Do not use with an extension cord or overload electrical outlets. • Supervision is needed when used by or near children, disabled persons or those with mental disabilities. Return policy / ZENS warranty Dear customer, All ZENS products are designed and manufactured to meet the highest standards and deliver high-quality performance. In case you encounter any difficulties when using your product, we recommend that you first consult the user manual or the information in the support section of www.makezens.com. In the unlikely event of failure during the warranty period ZENS will arrange for your product to be serviced. - 5 - Warranty terms The warranty begins on the date of purchase and expires after 24 months. If any defect due to faulty materials and/or workmanship occurs within the warranty period, ZENS will make arrangements for service. Where a repair is not possible or is deemed uneconomical ZENS may agree to replace the product. Replacement will be offered at ZENS discretion and the warranty will continue from the date of original purchase. The ZENS warranty applies provided the product has been handled properly for its intended use and in accordance with the operating instructions. The warranty does not cover for the losses consequent in nature, including but not limited to loss of data or loss of business. The ZENS Warranty does not apply if: • The purchase documents have been altered in any way or made illegible. • The model- and/or serial number on the product has been altered, removed or made illegible. • Repairs or product modifications and alterations have been carried out by unauthorized service organizations or persons. • The product is being used for commercial purpose. • The defect is caused by abuse or misuse of the product or by environmental conditions that are not in conformance with the recommended operations of the product. • The unit has been damaged - including but not limited to damage by pets, lightning, abnormal voltage, water or fire, natural disaster or transport accident. • The product is defective due to wear of parts, which can be considered as consumable parts by their nature • The product does not function properly because it was not originally designed, manufactured, approved and/or authorized for the country where you use the product, which might occur in instances where the product has been - 6 - purchased in another country other than that of its intended use. This warranty gives you specific legal rights. As this might vary from country to country some of above might not apply to you. This warranty is only valid in the country were the product is purchased and is not transferable and does not extend to users other than the original purchaser. Service needed? In order to avoid unnecessary inconvenience, we advise you to read the user manual or consult the support section on www.makezens.com before contacting ZENS. If service is required do not return the product without first contacting ZENS. To get this product repaired or replaced, please contact ZENS during the warranty period by email ([email protected]) and include the following details: email address, name, address, te…

Text truncated - open the document above for the full version.

Date: 2020-12-1 1 TUY Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern: Authority to Act as A�ent I oint TUV Rheinland (Shenzhen) Co., Ltd. to act app as our agent m the preparation of this app � ication for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also ce巾fy that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canada's regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUY Rheinland Group, still resides with Luxshare Precision Industry Co., Ltd. / Fl9or 2, Block A Sanvo New Industrial Area We t Hao i Communit I Sha"in Subdistrict ffice Bao'an District Shenzhen P.R. China For TCB applications, We certify that we are not subject to denial offederal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: 12 months By Title On behalf of QF094234 趴＼ 灼 (Signature) Product Design Telephone Engineer Luxshare Precision Industry Co., Ltd (Company Name) Page 1 of 1 Bin Lin (Print Name) 15197269372 Revision 0

Stick on the back of product

Produkte Products Prüfbericht - Nr.: Test Report No. CN208N8X 001 Seite 21 von 23 Page 21 of 23 6 Safety Human Exposure 6.1 Radio Frequency Exposure Compliance 6.1.1 Electromagnetic Fields RESULT: Pass Test Specification Test standard : CFR47 FCC Part 2: Subpart J Section 1.1310 FCC CFR 47 Part 1(1.1310) KDB 680106 D01 v03 According to the table 1 of FCC Part 2.1310, the reference limit as below: Test Setup: Produkte Products Prüfbericht - Nr.: Test Report No. CN208N8X 001 Seite 22 von 23 Page 22 of 23 Test Result: Table: H-Field Strength at 15 cm from the edges surrounding the EUT and 20cm from the top surface of the EUT EUT Test Mode Measured H-Field Strength Values (A/m) 50% Limit (A/m) Limit (A/m)Result Test Position Top Test Position front Test Position rear Test Position left Test Position right 1% Battery Level 0.815 1.63 Pass 50% Battery Level 0.815 1.63 Pass 99% Battery Level 0.815 1.63 Pass

Produkte Products Prüfbericht-Nr.: Test report no.: CN208N8X 001 Auftrags-Nr.: Order no.: 168287068 Seite 1 von 23 Page 1 of 23 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2020-11-06 Auftraggeber: Client: Luxshare Precision Industry Co., Ltd. Floor 2, Block A, Sanyo New Industrial Area, West Haoyi Community, Shajing Subdistrict Office, Bao'an District, Shenzhen, P. R. China Prüfgegenstand: Test item: Apple Watch USB-Stick Wireless Charger Bezeichnung / Typ-Nr.: Identification / Type no.: ZEAW01B/00 (Trademark: ZENS) Auftrags-Inhalt: Order content: Type Test Prüfgrundlage: Test specification: CFR47 FCC Part 15: Subpart C Section 15.207 CFR47 FCC Part 15: Subpart C Section 15.209 CFR47 FCC Part 15: Subpart C Section 15.215 CFR47 FCC Part 2: Subpart J Section 1.1310 Wareneingangsdatum: Date of sample receipt: 2020-11-07 Refer to photos document Prüfmuster-Nr.: Test sample no: A002934917-001 Prüfzeitraum: Testing period: 2020-11-17 – 2020-12-03 Ort der Prüfung: Place of testing: TÜV Rheinland (Shenzhen) Co., Ltd. Prüflaboratorium: Testing laboratory: TÜV Rheinland (Shenzhen) Co., Ltd. Prüfergebnis*: Test result*: Pass geprüft von: tested by: X Signed by: Alex Lan genehmigt von: authorized by: X Signed by: Winnie Hou Datum: Date: 2020-12-21 Ausstellungsdatum: Issue date: 2020-12-21 Stellung / Position Senior Project Engineer Stellung / Position Department Manager Sonstiges / Other: FCC ID: 2AYYSZEAW01B Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be V05 duplicated in extracts. This test report does not entitle to carry any test mark. TÜV Rheinland (Shenzhen) Co., Ltd. 1601 R&D Room, 1602-1604, 17-18F, Building 7 Site C, Vanke Cloud City Phase I, Xingke First Street, Xili Street, Xili Community, Nanshan District, Shenzhen 518052, P.R. China Mail: [email protected] · Web: www.tuv.com Produkte Products Prüfbericht - Nr.: Test Report No. CN208N8X 001 Seite 2 von 23 Page 2 of 23 Test Summary 5.1.1 ANTENNA REQUIREMENT RESULT: Pass 5.1.2 20DB BANDWIDTH RESULT: Pass 5.1.3 RADIATED SPURIOUS EMISSION RESULT: Pass 5.1.4 CONDUCTED EMISSIONS RESULT: Pass 6.1.1 ELECTROMAGNETIC FIELDS RESULT: Pass Produkte Products Prüfbericht - Nr.: Test Report No. CN208N8X 001 Seite 3 von 23 Page 3 of 23 Contents 1 GENERAL REMARKS ........................................................................................................................... 4 1.1 COMPLEMENTARY MATERIALS ............................................................................................................ 4 2 TEST SITES ........................................................................................................................................ 5 2.1 TEST FACILITIES ................................................................................................................................. 5 2.2 LIST OF TEST AND MEASUREMENT INSTRUMENTS................................................................................. 5 2.3 TRACEABILITY .................................................................................................................................... 6 2.4 CALIBRATION ..................................................................................................................................... 6 2.5 MEASUREMENT UNCERTAINTY............................................................................................................. 6 2.6 LOCATION OF ORIGINAL DATA ............................................................................................................. 6 2.7 STATUS OF FACILITY USED FOR TESTING ............................................................................................. 6 3 GENERAL PRODUCT INFORMATION ...................................................................................................... 7 3.1 PRODUCT FUNCTION AND INTENDED USE ............................................................................................. 7 3.2 RATINGS AND SYSTEM DETAILS .......................................................................................................... 7 3.3 INDEPENDENT OPERATION MODES ...................................................................................................... 7 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ......................................................................... 7 3.5 SUBMITTED DOCUMENTS..................................................................................................................... 7 4 TEST SET-UP AND OPERATION MODES ................................................................................................ 8 4.1 PRINCIPLE OF CONFIGURATION SELECTION ......................................................................................... 8 4.2 TEST OPERATION AND TEST SOFTWARE .............................................................................................. 8 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................................................ 8 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE ..............................................................…

Text truncated - open the document above for the full version.

Produkte Products Appendix A CN208N8X 001 Page 1 of 3 Appendix A: Photographs of the Test Set-Up APPENDIX A: PHOTOGRAPHS OF THE TEST SET-UP ....................................................................................................... 1 PHOTOGRAPH 1: SET-UP PHOTO FOR RADIATED SPURIOUS EMISSION, 9KHZ - 30MHZ ...................................................................... 2 PHOTOGRAPH 2: SET-UP PHOTO FOR RADIATED SPURIOUS EMISSION, 30MHZ - 1GHZ ...................................................................... 2 PHOTOGRAPH 3: SET-UP PHOTO FOR CONDUCTED EMISSION ON AC MAINS ..................................................................................... 3 PHOTOGRAPH 4: SET-UP PHOTO FOR RF EXPOSURE ..................................................................................................................... 3 Produkte Products Appendix A CN208N8X 001 Page 2 of 3 Photograph 1: Set-up photo for Radiated Spurious Emission, 9KHz - 30MHz Photograph 2: Set-up photo for Radiated Spurious Emission, 30MHz - 1GHz Produkte Products Appendix A CN208N8X 001 Page 3 of 3 Photograph 3: Set-up photo for Conducted Emission on AC Mains Photograph 4: Set-up photo for RF Exposure