2AZUX-S02IP Camera with Battery

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Shenzhen Anran Security Technology Co., Ltd Model Difference Product Name: IP Camera with Battery Model Number: S02, S01, S02J, S03, S06, N01, N02, N03, M01, M02, Q01, Q02 FCC Identifier: 2AZUX-S02 All the models are the same circuit and RF module, except the mode names and outlook color. Regards Sincerely Client’s signature Client’s name / title: Hans Yi / Manager Contact information: No.290, Jihua Road, Jihua street, Longgang District, Shenzhen, No.112

Shenzhen Anran Security Technology Co., Ltd 1/1 Letter of Authorization Company: Shenzhen Anran Security Technology Co., Ltd Address: No.290, Jihua Road, Jihua street, Longgang District, Shenzhen, No.112 Product Name: IP Camera with Battery Model Number: S02, S01, S02J, S03, S06, N01, N02, N03, M01, M02, Q01, Q02 FCC Identifier: 2AZUX-S02 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Hans Yi Date: 2021-05-11 Title: Manager Signature of applicant:

Shenzhen Anran Security Technology Co., Ltd 1/1 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2021-05-11 Subject: Request for Confidentiality FCC ID: 2AZUX-S02 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual No ☐ Internal Photos No ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Hans Yi Title: Manager

EUT PHOTO(External Photos) ANT 1 Photo s

Size:10.5*7.5mm M/N: S02 FCC ID: 2AZUX-S02 Label location

EUT PHOTO(Internal Photos) ※※※※※ END OF REPORT ※※※※※

FCC ID: 2AZUX-S02 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation wifi mode Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result Lowest 8.351 6.841 0.0048 1.0 PASS Middle 7.863 6.114 0.0043 1.0 PASS Highest 7.788 6.009 0.0042 1.0 PASS Remark: antenna gain=3.5dBi

Project No.: ZKT-210427L1534E Page 1 of 55 FCC TEST REPORT FCC ID: 2AZUX-S02 Report Number. .............................. : ZKT-210427L1534E Date of Test .................................................:Apr. 25, 2021 to May. 10, 2021 Date of issue .................................... : May. 10, 2021 Total number of pages ...................... 55 Test Result ....................................... : PASS Testing Laboratory. ........................ : Shenzhen ZKT Technology Co., Ltd. Address .......................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name ......................... : Shenzhen Anran Security Technology Co., Ltd Address .......................................... : No.290, Jihua Road, Jihua street, Longgang District, Shenzhen, No.112 Manufacturer's name ................... : Shenzhen Anran Security Technology Co., Ltd Address .......................................... : No.290, Jihua Road, Jihua street, Longgang District, Shenzhen, No.112 Test specification: Standard .......................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 ANSI C63.10:2013 Test procedure ................................. : / Non-standard test method ............. : N/A Test Report Form No. .................... : TRF-EL-110_V0 Test Report Form(s) Originator .... : ZKT Testing Master TRF .................................... : Dated: 2020-01-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name ................................. : IP Camera with Battery Trademark ...................................... : N/A Model/Type reference ...................... : S02 S01, S02J, S03, S06, N01, N02, N03, M01, M02, Q01, Q02 Ratings ............................................. : DC 3.7V from battery DC 5V from charger Project No.: ZKT-210427L1534E Page 2 of 55 Testing procedure and testing location: Testing Laboratory ................................... : Shenzhen ZKT Technology Co., Ltd. Address ...................................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Alen He Tested by (name + signature) .................... : Joe Liu Reviewer (name + signature) ..................... : Lake Xie Approved (name + signature) .................... : Project No.: ZKT-210427L1534E Page 3 of 55 Table of Contents Page 1. VERSION ..................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................. 6 2.1 TEST FACILITY ............................................................................................................... 7 2.2 MEASUREMENT UNCERTAINTY ................................................................................... 7 3. GENERAL INFORMATION .......................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT................................................................................. 8 3.2 DESCRIPTION OF TEST MODES ................................................................................... 9 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED ................ 9 3.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) ......................................... 9 3.5EQUIPMENTS LIST FOR ALL TEST ITEMS .................................................................. 10 4. EMC EMISSION TEST ............................................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT ................................................................. 11 4.1.1 POWER LINE CONDUCTED EMISSION Limits ................................................... 11 4.1.2 TEST PROCEDURE .............................................................................................. 11 4.1.3 DEVIATION FROM TEST STANDARD .................................................................. 11 4.1.4 TEST SETUP ......................................................................................................... 11 4.1.5 EUT OPERATING CONDITIONS ........................................................................... 11 4.1.6 TEST RESULT ....................................................................................................... 12 4.2 RADIATED EMISSION MEASUREMENT ...................................................................... 14 4.2.1 RADIATED EMISSION LIMITS .............................................................................. 14 4.2.2 TEST PROCEDURE .............................................................................................. 14 4.2.3 DEVIATION FROM TEST STANDARD .................................................................. 15 4.2.4 TEST SETUP ......................................................................................................... 15 4.2.5 EUT OPERATING CONDITIONS ........................................................................... 16 4.2.6 TEST RESULTS .................................................................................................... 17 5.RADIATED BAND EMISSIONMEASUREMENT ........................................................ 28 5.1 TEST REQUIREMENT: ................................ .................................................................. 28 5.2 TEST PROCEDURE ........................................................................…

Text truncated - open the document above for the full version.

EUT TEST PHOTO