2AZUX-Y2U3Security Camera

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Shenzhen Anran Security Technology Co., Ltd Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: Dec. 8, 25 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2AZUX-Y2U3 Shenzhen Anran Security Technology Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Luxing Yan Title: Manager Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Tel.: 18028763698 Email: [email protected]

1 | P a g e Shenzhen Anran Security Technology Co., Ltd Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Attestation Statements To: Federal Communications Commission Date: Dec. 8, 25 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: [2AZUX-Y2U3] Product Name: [Security Camera] This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature Printed Name: Luxing Yan Title: Manager Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Tel.: 18028763698 Email: [email protected] 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. The MCU “ AK3918AV100N“, The RF chip “ AIC8800D40L“ don’t support the mentioned function. ☐ The Memory used is limited to run the Cybersecurity or anti-virus software. The memory size is XXX, so don’t support the mentioned function. ☐ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. The storage capacity is XXX, so don’t support the mentioned function. ☐ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. The Operating system “XXX“ don’t support the mentioned function. Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check

Shenzhen Anran Security Technology Co., Ltd Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: Dec. 8, 25 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2AZUX-Y2U3 Shenzhen Anran Security Technology Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, [Herland International Trading Inc] (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. [Herland International Trading Inc] ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: Herland International Trading Inc FRN: 0036324101 Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Signature: Contact Person: Jianfeng Gao Tel: 001-909-772-1888 Email: jianfenggao@hyunturlee- commerce.com Applicant Company Name: Shenzhen Anran Security Technology Co., Ltd FRN: 0030911440 Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Signature: Contact Person: Luxing Yan Tel: 18028763698 Email: [email protected]

Shenzhen Anran Security Technology Co., Ltd Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China 12/8/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for: FCC ID: 2AZUX-Y2U3 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request permanent confidential treatment of the exhibits accompanying this certification application as outlined below : ⎯ Block Diagram ⎯ Schematics ⎯ Operational Description The above exhibits contain trade secrets and/or proprietary information that are not publicly available and materials that the Applicant has spent considerable efforts in developing. Public disclosure of these may be harmful to the Applicant and give an unfair advantage to competitors on the market. Sincerely, (Signature) Printed Name: Luxing Yan Title:Manager Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Tel.: 18028763698 Email:[email protected]

Shenzhen Anran Security Technology Co., Ltd Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Date: Dec. 8, 25 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2AZUX-Y2U3 I, the undersigned, hereby authorize (Shenzhen DL Testing Technology Co., Ltd.) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Shenzhen DL Testing Technology Co., Ltd.) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with (Shenzhen Anran Security Technology Co., Ltd ). We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, Applicant Signature: Printed Name: Luxing Yan Title: Manager Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Tel.: 18028763698 Email:[email protected]

Shenzhen Anran Security Technology Co., Ltd Product Similarity Declaration FCC ID: 2AZUX-Y2U3 Applicant: Shenzhen Anran Security Technology Co., Ltd Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Manufacturer: Shenzhen Anran Security Technology Co., Ltd Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Product Name: Security Camera Trade Mark: N/A Model Number: Y2U3, Y2U4, Y2U5, Y2U8, Y2M3, Y2M4, Y2M5, Y2M8, Y3U2, Y3U3, Y3U4, Y3U5, Y3U8, Y3M2, Y3M3, Y3M4, Y3M5, Y3M8 We (Shenzhen Anran Security Technology Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), All models are the same as the samples except model name and appearance color. Applicant Signature Printed Name: Luxing Yan Title: Manager Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Tel.: 18028763698 Email: [email protected]

Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 ※※※※※ END OF REPORT ※※※※※

Size: 20*10mm M/N: Y2U3 FCC ID: 2AZUX-Y2U3 Label location

Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 EUT PHOTO(Internal Photos) Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 ANT Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 ※※※※※ END OF REPORT ※※※※※

FCC ID: 2AZUX-Y2U3 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in KDB 447498 D01 V06, 1.1307(b) and 2.1091. Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation wifi 2.4G mode Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 16.576 45.4569 0.01864 1.0 PASS 802.11g 13.451 22.1360 0.00907 1.0 PASS 802.11n HT20 14.426 27.7077 0.01136 1.0 PASS 802.11n HT40 13.554 22.6673 0.00929 1.0 PASS Remark: antenna gain=3.14 dBi

TengxiangTechnology.Inc ProductNumber:AN2450-FPC239BX ProductName:Antenna Page2 Index: 1.Specification 2.CharacteristicsandReliabilityTest 3.Antenna-SParameterTestData 4.Antenna-RadiationPatternTestData 5.MechanicalandPackingDrawing RevisionHistory RevisionDateChangeNotificationDescription 1.02025.8.291.0 TengxiangTechnology.Inc ProductNumber:AN2450-FPC239BX ProductName:Antenna Page 3 1. Specification SamplePhoto A. ElectricalCharacteristics Frequency2400 -2500MHz S.W.R.<= 2.0 AntennaGain3.14 dBi PolarizationLinear Impedance50 Ohm B. Material& MechanicalCharacteristics CableType OD 1.13 mm，BIack ConnectorTypeI-PEX C. Environmental StorageTemperature- 40 ̊C ~ +80 ̊C OperationTemperature- 40 ̊C ~ +80 ̊C TengxiangTechnology.Inc ProductNumber:AN2450-FPC239BX ProductName:Antenna Page4 2.CharacteristicsandReliabilityTest TestItemsTestConditionandProcedureRequirementsResult 结果 1V.S.W.R.SetDUTonNetworkAnalyzer;makeindividual calibrationtotest DirectiveDUTspecificationPASS 2Insertion Loss SetDUTonNetworkAnalyzer;makeindividual calibrationtotest DirectiveDUTspecificationPASS 3Antenna Gain SetDUTonAntennaChamber;makeindividual calibrationtotest DirectiveDUTspecificationPASS 4SolderabilityGB/T2423.28-2005 Temp:260±5°C;Duration:5seconds TinevenlyonfullPASS 5PullTestHoldingwithindividualspecification;force appliedtoaxisofterminal. 1.DirectiveDUTspecification 2.FrequencyTol.≤5% PASS 6DimensionInspectionofdimension,color,material,package, surfaceprocess. DirectiveDUTspecificationPASS 7SaltSprayGB/T2423.17-2008 Temp:35°C;RH:≥95%;NaClsolution:≥ 5%;Time:24H 1.NoVisualDamage 2.FrequencyTol.≤5% PASS 8RoHSWithReferencetoIEC62321:2008withflowchartDirectiveRoHS2015/863/EUPASS TengxiangTechnology.Inc ProductNumber:AN2450-FPC239BX ProductName:Antenna Page 5 3. Antenna- S ParameterTest Data 4. Antenna- RadiationPatternTest Data TengxiangTechnology.Inc ProductNumber:AN2450-FPC239BX ProductName:Antenna Page 6 XZYZXY 2400MHz 2450MHz 2500MHz B C D AN2450-FPC239BX / Antenna 1/1 ±0.3±0.1±1 OD1.13 Part Number Name CB-113BS Coaxial Cable 1 No. 2 1 1 Q'ty 1 Material Finish A SYY 2024.08.29 DES BY Note: 1.Mark is important dimension;"Cpk "Identify for process control(CpK 1.33). 2.Tolerance:Unmarked tolerance refer to the standard tolerance please. 3.Pay attention to the direction of the connector. APPROVER DATE SIGN DESCRIPTION SCALE: APP BY Tolerance X.XX X.X X° TITLE: PART NO.: CUSTOMER P/N: CHK BY RF BY UNITS: mm REVISION: HFREACHRoHS2.0 CONFIDENTIAL AN2450-FPC1132 FPC Black CR-113-ZP-A 3 Cu I-PEX Au Plated AN2450-FPC1132 Black 1 2 3 端子朝向如图所示 WJ 2024.08.29 HC 2024.08.29 YCX 2024.08.29 100pcs/ PE bag Revision : A Customer : ALL APPROVED BY CHECKED BY DESIGNED BY Name: Page: 1 of 1 Date: Part Number : PACKING CRITERION 8000pcs/Carton 3. SEALING 。 MEAS G W: KGS N W: KGS QTY: PCS ITEM NO: C/NO MADE IN CHINA SIDE FRONT 2.PACKING 1 . Enter PE bag。 2025.08.29 AN2450-FPC239BX Antenna AN2450-FPC1132

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251112041R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 49 FCC Part 15C Test Report FCC ID: 2AZUX-Y2U3 Applicant: Shenzhen Anran Security Technology Co., Ltd Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Manufacturer: Shenzhen Anran Security Technology Co., Ltd Address: Room 1711, Building 4, Tianan Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China Product Name: Security Camera Trade Mark: N/A Model Number: Y2U3, Y2U4, Y2U5, Y2U8, Y2M3, Y2M4, Y2M5, Y2M8, Y3U2, Y3U3, Y3U4, Y3U5, Y3U8, Y3M2, Y3M3, Y3M4, Y3M5, Y3M8 Date of Receipt: Nov. 12, 2025 Test Date: Nov. 12, 2025 - Nov. 25, 2025 Date of Report: Nov. 25, 2025 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-251112041R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251112041R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 49 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 MEASUREMENT UNCERTAINTY 4 2 . GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 DESCRIPTION OF TEST MODES 6 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3 . EMC EMISSION TEST 9 3.1 CONDUCTED EMISSION MEASUREMENT 9 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2 TEST PROCEDURE 9 3.1.3 DEVIATION FROM TEST STANDARD 9 3.1.4 TEST SETUP 10 3.1.5 EUT OPERATING CONDITIONS 10 3.1.6 TEST RESULTS 11 3.2 RADIATED EMISSION MEASUREMENT 13 3.2.1 RADIATED EMISSION LIMITS 13 3.2.2 TEST PROCEDURE 14 3.2.3 DEVIATION FROM TEST STANDARD 14 3.2.4 TEST SETUP 14 3.2.5 EUT OPERATING CONDITIONS 15 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8 TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 23 3.3.1 TEST REQUIREMENT: 23 3.3.2 TEST PROCEDURE 23 3.3.3 DEVIATION FROM TEST STANDARD 23 3.3.4 TEST SETUP 24 3.3.5 EUT OPERATING CONDITIONS 24 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 29 3.4.1 APPLICABLE STANDARD 29 3.4.2 TEST PROCEDURE 29 3.4.3 DEVIATION FROM STANDARD 29 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251112041R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 49 Table of Contents Page 3.4.4 TEST SETUP 29 3.4.5 EUT OPERATION CONDITIONS 30 3.4.6 TEST RESULTS 30 4 . AVERAGE OUTPUT POWER 35 4.1 APPLIED PROCEDURES / LIMIT 35 4.1.1 TEST PROCEDURE 35 4.1.2 DEVIATION FROM STANDARD 35 4.1.3 TEST SETUP 35 4.1.4 EUT OPERATION CONDITIONS 35 4.1.5 TEST RESULTS 36 5 . POWER SPECTRAL DENSITY TEST 39 5.1 APPLIED PROCEDURES / LIMIT 39 5.1.1 TEST PROCEDURE 39 5.1.2 DEVIATION FROM STANDARD 39 5.1.3 TEST SETUP 39 5.1.4 EUT OPERATION CONDITIONS 39 5.1.5 TEST RESULTS 40 6 . 6DB BANDWIDTH TEST 43 6.1 APPLIED PROCEDURES / LIMIT 43 6.1.1 TEST PROCEDURE 43 6.1.2 DEVIATION FROM STANDARD 43 6.1.3 TEST SETUP 43 6.1.4 EUT OPERATION CONDITIONS 43 6.1.5 TEST RESULTS 44 7 . ANTENNA REQUIREMENT 49 7.1 STANDARD REQUIREMENT 49 7.2 EUT ANTENNA 49 8 . TEST SETUP PHOTO 49 9 . EUT PHOTO 49 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251112041R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 49 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.205, 15.209, 15.247(d) Radiated Spurious Emission PASS 15.209, 15.205 Band Edge Emission PASS 15.247(d) Conducted Spurious Emissions PASS 15.247(b) Average Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2% 9 Power Spectral Density ±2.45dBm Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251112041R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 49 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product Name: Security Camera Trade Mark: N/A Model Number: Y2U3, Y2U4, Y2U5, Y2U8, Y2M3, Y2M4, Y2M5, Y2M8, Y3U2, Y3U3, Y3U4, Y3U5, Y3U8, Y3M2, Y3M3, Y3M4, Y3M5, Y3M8 Test Model: Y2U3 Model Difference All models are same as the samples except model name and appearance color, they have the same structure and circuit. Operation Frequency: 2412~24…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. FCC ID: 2AZUX-Y2U3 Conducted Measurement Photos ※※※※※ END OF REPORT ※※※※※