2BAE5-S9PROWindow cleaning robot

USER MANUAL ULTRASONIC WATER SPRAY WINDOW CLEANING ROBOT BLUETOOTH CONNECTION (OPTIONAL APP CONTROL) 1.Bluetooth Reset (1) Turn off the robot, disconnect the DC power supply, and plug in the DC power supply again. (2) Press and hold the power/start button for more than 8 seconds. (3) When the reset is successful, the fan will stop rotating and then the buzzer will beep for 2 seconds Long press for more than 8 seconds 2.Turn on the Phone Network and Bluetooth 3.Download Tuya Smart App Register and Login 4.Adding Devices 5.Press“+” 6.Press“Done” 7.User Interface Thank you for choosing Ultrasonic Water Spray Window Cleaning Robot Please read this manual in detail before use to ensure your personal safety and the effective working of the product. 2 3 5 11 6 INDEX 12 13 13 14 15 15 16 17 18 18 ENGLISH Important safeguards Parts list Content of the box Installation intructions Instruction and cautions Path planning Spot cleaning route Meaningsofled indicator lamp andvoice Remote control Parameters Water tank maintenance Customer information Troubleshooting Safety Warranty Fault list Maintenance records 19 19 ENGLISH 2 PARTS LIST Box handle Front of base station Back of base station Side of base station Cover opening button Power-on indicator Retract wire button Suction plate deflation switch Base station sucker Power cord Safety rope port Floor tile alignment mark 3 PARTS LIST Water tank cover Press and hold for 3 seconds: Switch on/off Status Indicator Buzzer Sideview Cord installed Port Nozzle (normally not disassembled, )Direct load wipes Nozzle Power Cord Hole ON/OFF/Pause Button Mop Holder 4 Short press: start/continue/pause Remote Control x1 Safety Cable x1Water Bottle x1 Nozzle x1 User Manual x1 CONTENT OF THE BOX Window Cleaning Robot x1 Mops x10 PCS 5 Base station x1 INSTALLATION INTRUCTIONS 6 Put the base station on the surface of the fixed object with a clean and smooth surface (avoiding crevices),and turn the knob at the rear of the base station clockwise to the "O" to adsorb. Insert the safety rope buckle horizontally into the hole on the side of the base station, and rotate 90 ° clockwise to lock, fasten the safety rope and tie it to an indoor fixture before operating the device. Adsorption base station A B 90° INSTALLATION INTRUCTIONS 7 C Pull out the plug from the base station and insert it into the socket. The blue indicator is always on to indicate that the power is on. *It is recommended to fix the safety rope buckle on the protective railing. Connect the power Indicator INSTALLATION INTRUCTIONS 8 Pull power cord out to the appropriate length. When the device is working, do not disconnect the power. If the power is off during operation, the device must be retracted in time to prevent the device from falling. Pull out the wire Connected successfully Adsorption base station Fasten the safety rope Connect the power К Л М Pull out the wire Н Step 1 Step 3 Step 2 Step 4 *Do not disconnect the power when the device is running; If the power is off during operation, the device needs to be removed in time, otherwise there is a risk of falling. This product cannot be drenched, dry the surface residual moisture after filling with water. Fill the water tank and cover with the plug Using concentrated cleaning liquid in this product is strictly prohibited, so as not to block the spray hole and pump. If there are sand and dust on the glass surface, it is recommended to clean it manually first to avoid scratching the glass when the robot is working. If manual cleaning is not possible, it is recommended to turn off the water spray function and use dry mops to wipe off the sand and dust first. INSTALLATION INTRUCTIONS Cover each mop holder with a mop. 9 Please make sure the Mop Holder is installed inproper position before use o After the holder is installed, please observe from sideways 360 to ensure that each snap is stuck in place to avoid air leakage. Power/Start button Long-press the power button (more than 3 seconds), and the robot will turn on. After the fan is running, attach the robot on the glass at a location far away from the window frame. If the robot can't suck on glass, please check whether the holder has buckled up to cause air leakage. 10 INSTRUCTION AND CAUTIONS Safety Rope Working Environment Inspection Do not use on broken and cracked glass. If outside working at height is required, ground safety warnings must be set up to prevent accidental personal injury. Wet and Dry Wipe If there is slipping and twisting when the robot climbing, please install a dry wipe and turn on the water spray. If there are small areas of stubborn stains, you can use "spot cleaning" and turn on the water spray. Start Ensure the power cord and plug are completely connected. Remove Robot from Glass Power Outage Protection Ensure the glass surface is dry, please do not use it when it is raining or when the glass surface is foggy. If the robot has serious shaking or rattling, please install a dry wipe cloth. Long press the Start /Power button (morethan 3 seconds) the robot will turn on. After the fan is running, attach the robot on the glass to a location far away from the window frame. Check whether the safety rope is intact and is on a stable object. The robot cannot be used when there are stickers or oil on the glass surface, to avoid robot slipping and falling from glass. If there are sand and dust on the glass surface, it is recommended to clean it manua lly first to avoid scratching the glass when the robot is working. If manual cleaning is not possible, it is recommended to turn off the water spray function and use dry mops to wipe off the sand and dust first. If there are only dirt stains, it can be wiped directly with the water spray (default turn on water spray). Ensure the robot has been stuck to the glass and then let go. Short press the power button to start the robot. When the robot is running, hold the safety cable with one hand, short press to stop the robot and take it down with the o…

Text truncated - open the document above for the full version.

0033462797

Shanxi Jiashida Robot Technology Co., Ltd 17/f, huanneng tech block, no17,Gaoxin St.,Zonggai shifan dist. Taiyuan, China Letter of Authorization Company: Shanxi Jiashida Robot Technology Co., Ltd Address: 17/f, huanneng tech block, no17,Gaoxin St.,Zonggai shifan dist. Taiyuan, China Product Name: Window cleaning robot Model Number(s): SATUO S9 PRO Product Description: Window cleaning robot We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Sep. 18, 2024 Name: Baoliang Wang Title: General Manager Company: Shanxi Jiashida Robot Technology Co., Ltd

Report No.: AGC11532240802AP02 Page 1 of 7 EXTERNAL PHOTOS ALL VIEW OF EUT Window Cleaning Robot TOP VIEW OF EU Report No.: AGC11532240802AP02 Page 2 of 7 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC11532240802AP02 Page 3 of 7 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC11532240802AP02 Page 4 of 7 RIGHT VIEW OF EUT Base station TOP VIEW OF EUT Report No.: AGC11532240802AP02 Page 5 of 7 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC11532240802AP02 Page 6 of 7 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC11532240802AP02 Page 7 of 7 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 30mm*20mm FCC ID: 2BAE5-S9PRO This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Report No.: AGC11532240802AP02 Page 1 of 7 INTERNAL PHOTOS Window Cleaning Robot OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC11532240802AP02 Page 2 of 7 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC11532240802AP02 Page 3 of 7 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) Report No.: AGC11532240802AP02 Page 4 of 7 INTERNAL VIEW OF EUT (FIGURE 5) INTERNAL VIEW OF EUT (FIGURE 6) 2.4G RX Antenna Report No.: AGC11532240802AP02 Page 5 of 7 INTERNAL VIEW OF EUT (FIGURE 7) INTERNAL VIEW OF EUT (FIGURE 8) BT Antenna Report No.: AGC11532240802AP02 Page 6 of 7 INTERNAL VIEW OF EUT (FIGURE 9) INTERNAL VIEW OF EUT (FIGURE 10) Report No.: AGC11532240802AP02 Page 7 of 7 Base station INTERNAL VIEW OF EUT (FIGURE 1) ADAPTER OF EUT ****************************************End of Report*************************************

Page 1 of 10 RF Exposure Report Report No.: AGC11532240802FH01 FCC ID : 2BAE5-S9PRO APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Window cleaning robot BRAND NAME : N/A MODEL NAME : SATUO S9 PRO APPLICANT : Shanxi Jiashida Robot Technology Co., Ltd DATE OF ISSUE : Aug. 29, 2024 STANDARD(S) : FCC Part 2 Subpart J §2.1091 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC11532240802FH01 Page 2 of 10 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Aug. 29, 2024 Valid Initial Release Report No.: AGC11532240802FH01 Page 3 of 10 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 3. Test Environment ............................................................................................................................................ 6 3.1 Address Of The Test Laboratory ............................................................................................................... 6 3.2 Test Facility ................................................................................................................................................ 6 3.3 Environmental Conditions ......................................................................................................................... 7 4. Portable Device Evaluation Method and Limit ............................................................................................. 8 5. Mobile Device Evaluation Method and Limit ................................................................................................ 9 6. Measurement Results ................................................................................................................................... 10 7. Measurement Evaluation .............................................................................................................................. 10 Report No.: AGC11532240802FH01 Page 4 of 10 1. General Information Applicant Shanxi Jiashida Robot Technology Co., Ltd Address 17/f, huanneng tech block, no17,Gaoxin St.,Zonggai shifan dist. Taiyuan, China Manufacturer Shanxi Jiashida Robot Technology Co., Ltd Address 17/f, huanneng tech block, no17,Gaoxin St.,Zonggai shifan dist. Taiyuan, China Factory Shanxi Jiashida Robot Technology Co., Ltd Address 17/f, huanneng tech block, no17,Gaoxin St.,Zonggai shifan dist. Taiyuan, China Product Designation Window cleaning robot Brand Name N/A Test Model SATUO S9 PRO Series Model(s) N/A Difference Description N/A Date of receipt of test item Aug. 20, 2024 Date of Test Aug. 20, 2024~Aug. 29, 2024 Deviation from Standard No any deviation from the test method Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-RF Exposure-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Cici Li (Project Engineer) Aug. 29, 2024 Reviewed By Calvin Liu (Reviewer) Aug. 29, 2024 Approved By Max Zhang Authorized Officer Aug. 29, 2024 Report No.: AGC11532240802FH01 Page 5 of 10 2. Product Information 2.1 Product Technical Description Frequency Band (Operating) Bluetooth: 2.402GHz ~ 2.480GHz Other: Hardware Version V1.0 Software Version V1.0 Modulation Type BLE GFSK 1Mbps GFSK 2Mbps BT_BR_EDR GFSK, EDR π /4-DQPSK, 8DPSK Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Antenna Designation PCB Antenna Antenna Gain 2.5 dBi Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Report No.: AGC11532240802FH01 Page 6 of 10 3. Test Environment 3.1 Address Of The Test Laboratory Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to follow CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories.) A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to follow ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC-Registration No.: 975832 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the FCC (Federal Communications Commission). The acceptance letter from the FCC is maintained in our files with Registration 975832. IC-Registration No.: 24842(CAB identifier: CN0063) Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the Certification and Engineering Bureau of Industry Canada. The acceptance letter from the IC is maintained in our files with Registration 24842. Report No.: AGC11532240802FH01 Page 7 of 10 3.3 Environmental Conditions Normal Conditions Temperature range (°C) 15 - 35 Relative humidity range 20 % - 75 % Pressure range (kPa) 86 - 106 Power supply DC 24V by adapter…

Text truncated - open the document above for the full version.

BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China Product Name: BT3L Antenna Type: PCB antenna Writer: Yinhua Zhang Maximum Gain：2.5dBi Efficiency:62.86% BT3L Antenna test report Version 1.0.0 Date：2020-05-12 NO：0000000001 Antenna Test Report Global Intelligent Platform BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China Content 1. General Description ................................................................................ 3 2. Technical Information ............................................................................. 3 3. Test Standards ......................................................................................... 3 4. Test Item .................................................................................................. 4 5. Test Photo ................................................................................................ 4 Appendix A S11/VSWR ............................................................................. 5 Appendix B Gain and Efficiency ................................................................ 6 Appendix C Radiation Pattern(1D and 3D) ................................................ 7 Appendix D Test Setup Photo ..................................................................... 9 Appendix E EUT Photo .............................................. ...............................9 BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China 1.General Description EUT Name BT3L Antenna Wireless type Bluetooth Antenna Type PCB antenna Dimensions Appendix A 2.Technical Information Frequency Range 2402MHz~2480MHz Test Frequency 2400,2410......2500MHz 3.Test Standards Identity Document Title IEEE 149-1979 IEEE Standard Test Procedures for Antennas BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China 4. Test Item Report Section Description Appendix B S11/VSWR Appendix C Gain and Efficiency Appendix D Radiation Pattern（1D and 3D） 5. Test Photo Report Section Description Appendix E Test Setup Photo BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China Appendix A Antenna Dimension Appendix B S11/VSWR Frequency (MHz) 2400 2450 2500 Return Loss -8.73 -11.76 -11.21 BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China VSWR 2.16 1.71 1.77 Appendix C Gain and Efficiency Frequency (MHz) Efficiency(%) Gain（dBi） 2400 52.29% 1.62 2410 52.17% 1.71 2420 53.14% 1.93 2430 54.16% 1.98 2440 57.62% 2.00 2450 59.64% 2.17 2460 61.55% 2.45 2470 60.64% 2.38 BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China 2480 62.86% 2.50 2490 59.85% 2.30 2500 60.41% 2.49 Appendix D Radiation Pattern(1D and 3D) BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China BT3L Antenna test report Hangzhou Tuya Information Technology Co.,Ltd Room701,Building3,More Center,No.87 GuDun Road, Hangzhou,Zhejiang, China Appendix E Test Setup Photo

Page 1 of 71 FCC Test Report Report No.: AGC11532240802FR01 FCC ID : 2BAE5-S9PRO APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Window cleaning robot BRAND NAME : N/A MODEL NAME : SATUO S9 PRO APPLICANT : Shanxi Jiashida Robot Technology Co., Ltd DATE OF ISSUE : Aug. 29, 2024 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation Of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC11532240802FR01 Page 2 of 71 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Aug. 29, 2024 Valid Initial Release Report No.: AGC11532240802FR01 Page 3 of 71 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ..................................................................................................................... 6 2.2 Test Frequency List ..................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ................................................................................................................. 7 2.4 Test Methodology......................................................................................................................................... 7 2.5 Special Accessories ..................................................................................................................................... 7 2.6 Equipment Modifications ............................................................................................................................. 7 2.7 Antenna Requirement .................................................................................................................................. 7 3. Test Environment ............................................................................................................................................ 8 3.1 Address of the Test Laboratory .................................................................................................................... 8 3.2 Test Facility .................................................................................................................................................. 8 3.3 Environmental Conditions ........................................................................................................................... 9 3.4 Measurement Uncertainty ........................................................................................................................... 9 3.5 List of Equipment Use ............................................................................................................................... 10 4.System Test Configuration ............................................................................................................................ 12 4.1 EUT Configuration ..................................................................................................................................... 12 4.2 EUT Exercise ............................................................................................................................................. 12 4.3 Configuration of Tested System ................................................................................................................ 12 4.4 Equipment Used In Tested System ........................................................................................................... 12 4.5 Summary of Test Results ........................................................................................................................... 13 5. Description of Test Modes ........................................................................................................................... 14 6. Duty Cycle Measurement ............................................................................................................................. 15 7. RF Output Power Measurement .................................................................................................................. 16 7.1 Provisions Applicable ................................................................................................................................. 16 7.2 Measurement Procedure ........................................................................................................................... 16 7.3 Measurement Setup (Block Diagram of Configuration) ............................................................................ 16 7.4 Measurement Result ................................................................................................................................. 17 8. 6dB Bandwidth Measurement ...................................................................................................................... 21 8.1 Provisions Applicable ................................................................................................................................. 21 8.2 Measurement Procedure ........................................................................................................................... 21 8.3 Measurement Setup (Block Diagram of Configuration) ............................................................................ 21 8.4 Measurement Results ................................................................................................................................ 22 9. Power Spectral Density Measurement ........................................................................................................ 29 9.1 Provisions Applicable ..................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC11532240802AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC11532240802AP01 Page 2 of 2 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP ****************************************End of Report*************************************