A2HCN6Q15ENotebook Computer

EN - 1 EN Laptop O rdenador portátil User manual Manual del usuario CN6Q15 / CN6QF5 / NS15A6 avita-americas.com EN - 2 IMPORTANT SAFETY INSTRUCTIONS Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat. • Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. • Only use attachments / accessories specifi ed by the manufacturer. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. ADDITIONAL SAFETY INFORMATION • The AC adapter and apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be placed on the apparatus. • Always leave suffi cient space around the product for ventilation. Do not place product in or on a bed, rug, in a bookcase or cabinet that may prevent air fl ow through vent openings. • Do not place lighted candles, cigarettes, cigars, etc. on the product. • Care should be taken so that objects do not fall into the product. • Do not attempt to disassemble the cabinet. This product does not contain customer serviceable components. • To prevent the risk of fi re or electric shock, do not expose this apparatus to rain or moisture. • Do not play your headset at high volume. Hearing experts warn against extended high-volume play. • Warning: The mains plug is used as disconnect device, the disconnect device shall remain readily operable. • Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualifi ed personnel. EN - 3 EN • WARNING: Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus. Use the device where the ambient temperature is between 0 and 35°C (32 to 95°F). Low or high temperature conditions might cause the device to change its behavior to regulate its temperature. Using this device in very cold conditions outside of its operating range might temporarily shorten battery life and could cause temperatures. Using the devices in very hot conditions can permanently shorten battery life. Battery safety This device contains a built-in battery, improper use of which may result in explosion. Do not heat, open, puncture, mutilate, or dispose of the product in fi re. Do not leave the device in direct sunlight for an extended period of time, which could cause melting or battery damage. The battery in this device is not user replaceable and should only be replaced by AVITA or a AVITA Authorized Service Provider. • Low air pressure at high altitude. • Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types). • Disposal of the battery into fi re or a hot oven, or mechanically crushing or cutting of the battery can result in an explosion. • Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of fl ammable liquid of gas. • A battery subjected to extremely low air pressure may result in an explosion or the leakage of fl ammable liquid or gas. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. SAR The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/Kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. To avoid the possibility of exceeding the FCC radio frequency exposure limits, hu man proximity to the antenna should be minimized. For body worn operation, this device has been tested and meets the FCC RF exposure. This device was tested for typical body-worn operations with the back of the tablet pc kert 0mm from the body. EN - 4 FCC information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference …

Text truncated - open the document above for the full version.

Electronics Ltd A member of the ALCO group 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong Tel: (852) 2562 6121, Fax: (852) 2811 1056 16 Oct. 2020 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows: √ Electronics/electrical designs, including software & firmware √Construction design/Physical design/Enclosure √PCB layout □ (Others, please specify) T he only differences between these models are the follows for marketing purpose: □ Color □ Cosmetic details √Trade name √Model Number □ (Others, please specify) Item No. New model Model Number Trade Name Remarks 1 √ YES CN6Q15 VENTURER / AVITA 2 √ YES NS15A6 AVITA 3 √ YESCN6QF5 VENTURER / AVITA 4 5 6 The sample being submitted for conformity assessment is CN6Q15 (tested model) of the above list. Best Regards, Alco Electronics Ltd PEGGY SUEN Secretary, Engineering Dept.

2020-11-23 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen Huatongwei International Inspection Co., Ltd./ 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China / Hans Hu,. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Alco Electronics Ltd / 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong. Dated this Nov.23, 2020 Agency agreement expiration date: Nov.23, 2021 By: Peggy Suen Signature Printed Title: Secretary, E/G Dept. On behalf of : Alco Electronics Ltd Telephone: +852 25626121

2020-11-23 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: A2HCN6Q15E Product Name: Notebook Computer Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this Nov.23, 2020 By: Peggy Suen Signature Printed Title: Secretary, E/G Dept. On behalf of : Alco Electronics Ltd Telephone: +852 25626121

FCC Software Configuration Control Declaration Rev1.1 Alco Electronics Ltd FCC Software Configuration Control Declaration Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: Notebook Computer / CN6Q15, NS15A6, CN6QF5 Regarding FCC Country Code Selection guidelines identified in KDB 594280v02r01. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Peggy Suen Date: 2020-11-23 Title: Secretary, E/G Dept. Signature of applicant

External Photos

ALCO MODEL # : CN6QF5 T56E1US-XX LABELS ON UNIT (UL VERSION) 22-10-2020 REVISED DATE: SPEC LABEL (P/N 809-6Q1596W010) 34mm 3 mm 3 mm Model : CN6QF5 SAMPLE DC / C.C. 19V 2.1A FCC ID: A2HCN6Q15E Made in China / Fabriqué en Chine PURA LAPTOP Model : CN6Q15 SAMPLE DC / C.C. 19V 2.1A FCC ID: A2HCN6Q15E Made in China / Fabriqué en Chine PURA LAPTOP Model : CN6QF5 SAMPLE DC / C.C. 19V 2.1A FCC ID: A2HCN6Q15E Made in China / Fabriqué en Chine PURA LAPTOP Model : CN6Q15 SAMPLE DC / C.C. 19V 2.1A FCC ID: A2HCN6Q15E Made in China / Fabriqué en Chine PURA LAPTOP 7.3 mm 1.6 mm 1.2 mm 2.7 mm 1.2 mm Model : NS15A6 SAMPLE DC / C.C. 19V 2.1A FCC ID: A2HCN6Q15E Made in China / Fabriqué en Chine PURA LAPTOP CONFORMS TO UL STD. UL62368-1 CERTIFIED TO CSA STD. C22.2 No. 62368-1 CONFORMS TO UL STD. UL62368-1 CERTIFIED TO CSA STD. C22.2 No. 62368-1 CONFORMS TO UL STD. UL62368-1 CERTIFIED TO CSA STD. C22.2 No. 62368-1 CONFORMS TO UL STD. UL62368-1 CERTIFIED TO CSA STD. C22.2 No. 62368-1 CONFORMS TO UL STD. UL62368-1 CERTIFIED TO CSA STD. C22.2 No. 62368-1 i3 (10th) LABEL (P/N 809-000INTW120)

Internal Photos

Page: 1 of 39 TEST REPORT Report No. ...................................... : CHTEW20110039 Report verificaiton: Project No. ...................................... : SHT2010078803EW FCC ID ............................................. : A2HCN6Q15E Applicant’s name ........................... : Alco Electronics Ltd Address ............................................. : 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong Test item description .................... : Notebook Computer Trade Mark ....................................... : Venturer / AVITA Model/Type reference ....................... : CN6Q15 Listed Model(s) ................................. : NS15A6, CN6QF5 Standard ......................................... : FCC 47 CFR Part2.1093 IEEE Std C95.1, 1999 Edition IEEE 1528: 2013 Date of receipt of test sample..........: Oct.29, 2020 Date of testing..............................: Oct.30, 2020- Nov.05, 2020 Date of issue...............................: Nov.06, 2020 Result .................. ........................: PASS Compiled by ( position+printedname+signature) ... : File administrators: Fanghui Zhu Supervised by ( position+printedname+signature) ... : Test Engineer: Patrick Qiu Approved by ( position+printedname+signature) ... : Manager: Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW20110039 Page: 2 of 39 Issued: 2020-11-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V02 (2020-06) Contents 1. Statement of Compliance 3 2. Test Standards and Report version 4 2.1. Test Standards 4 2.2. Report version 4 3. Summary 5 3.1. Client Information 5 3.2. Product Description 5 3.3. RF Specification Description 6 3.4. Testing Laboratory Information 7 3.5. Environmental conditions 7 4. Equipments Used during the Test 8 5. Measurement Uncertainty 9 6. SAR Measurements System Configuration 10 6.1. SAR Measurement Set-up 10 6.2. DASY5 E-field Probe System 11 6.3. Phantoms 12 6.4. Device Holder 12 7. SAR Test Procedure 13 7.1. Scanning Procedure 13 7.2. Data Storage and Evaluation 15 8. Position of the wireless device in relation to the phantom 17 8.1. Body Exposure conditions 17 9. Dielectric Property Measurements & System Check 18 9.1. Tissue Dielectric Parameters 18 9.2. System Check 19 10. SAR Exposure Limits 26 11. Conducted Power Measurement Results 27 11.1. Wi-Fi 27 11.2. Bluetooth 29 12. Maximum Tune-up Limit 30 13. Antenna Location 34 14. Measured and Reported SAR Results 35 15. SAR Measurement Variability 37 16. Simultaneous Transmission analysis 38 17. TestSetup Photos 39 18. External and Internal Photos of the EUT 39 Report No.: CHTEW20110039 Page: 3 of 39 Issued: 2020-11-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V02 (2020-06) 1. Statement of Compliance Maximum Reported SAR (W/kg @1g) RF Exposure Conditions DTS NII Simultaneous TX Body-worn(Dist.= 0mm) 0.488 0.266 0.695 This device is in compliance with Specific Absorption Rate (SAR) for general population/uncontrolled exposure limits (1.6 W/kg) specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEE C95.1-1992, and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528-2013 and FCC KDB publications. Report No.: CHTEW20110039 Page: 4 of 39 Issued: 2020-11-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V02 (2020-06) 2. Test Standards and Report version 2.1. Test Standards The tests were performed according to following standards: FCC 47 Part 2.1093: Radiofrequency radiation exposure evaluation: portable devices. IEEE Std C95.1, 1999 Edition: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE Std 1528™-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. FCC published RF exposure KDB procedures: 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04: SAR Measurement Requirements for 100 MHz to 6 GHz 865664 D02 RF Exposure Reporting v01r02: RF Exposure Compliance Reporting and Documentation Considerations 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies 248227 D01 802 11 Wi-Fi SAR v02r02: SAR Measurement Proceduresfor802.11 a/b/g Transmitters 616217 D04 SAR for laptop and tablets v01r02: describes the SAR evaluation requirements for laptop, notebook, netbook and tablet computers TCB workshop April, 2019; Page 19, Tissue Simulating Liquids (TSL) 2.2. Report version Revision No. Date of issue Description N/A 2020-11-06 Original Report No.: CHTEW20110039 Page: 5 of 39 Issued: 2020-11-06 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V02 (2020-06) 3. Summary 3.1. Client Information Applicant: Alco Electronics Ltd Address: 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong Manufacturer: Alco Electronics Ltd Address: 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong 3.2. Product Description Main unit Name of EUT: Notebook Co…

Text truncated - open the document above for the full version.

Test Laboratory: Huatongwei International Inspection Co., Ltd.,SAR LabDate: 11/5/2020 Wifi 2.4G-Body Communication System: UID 0, Generic WIFI (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2412 MHz; σ = 1.805 S/m; ε r = 40.516; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature:22.6°C;Liquid Temperature:22.4°C; DASY Configuration: lProbe: EX3DV4 - SN7494; ConvF(7.91, 7.91, 7.91) @ 2412 MHz; Calibrated: 4/1/2020 lSensor-Surface: 1.4mm (Mechanical Surface Detection) lElectronics: DAE4 Sn1549; Calibrated: 4/4/2020 lPhantom: ELI V8.0 ; Type: QD OVA 004 AA ; Serial: 2078 lDASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) Bottom/CH 1/Area Scan (201x71x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.776 W/kg Bottom/CH 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 21.07 V/m; Power Drift = -0.12 dB Peak SAR (extrapolated) = 0.997 W/kg SAR(1 g) = 0.440 W/kg; SAR(10 g) = 0.183 W/kg Maximum value of SAR (measured) = 0.771 W/kg 0 dB = 0.771 W/kg = -1.13 dBW/kg Appendix A: SAR Test Data Plots Plot No.1 Test Laboratory: Huatongwei International Inspection Co., Ltd.,SAR LabDate: 11/5/2020 Wifi 5G U-NII-1-Body Communication System: UID 0, Generic WIFI (0); Frequency: 5180 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5180 MHz; σ = 4.472 S/m; ε r = 35.928; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature:22.5°C;Liquid Temperature:22.3°C; DASY Configuration: lProbe: EX3DV4 - SN7494; ConvF(5.58, 5.58, 5.58) @ 5180 MHz; Calibrated: 4/1/2020 lSensor-Surface: 1.4mm (Mechanical Surface Detection) lElectronics: DAE4 Sn1549; Calibrated: 4/4/2020 lPhantom: ELI V8.0 ; Type: QD OVA 004 AA ; Serial: 2078 lDASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) Bottom/CH 36/Area Scan (241x81x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.455 W/kg Bottom/CH 36/Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 9.176 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 0.733 W/kg SAR(1 g) = 0.183 W/kg; SAR(10 g) = 0.067 W/kg Maximum value of SAR (measured) = 0.397 W/kg 0 dB = 0.397 W/kg = -4.01 dBW/kg Appendix A: SAR Test Data Plots Plot No.2 Test Laboratory: Huatongwei International Inspection Co., Ltd.,SAR LabDate: 11/5/2020 Wifi 5G U-NII-2A-Body Communication System: UID 0, Generic WIFI (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5280 MHz; σ = 4.542 S/m; ε r = 35.747; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature:22.4°C;Liquid Temperature:22.2°C; DASY Configuration: lProbe: EX3DV4 - SN7494; ConvF(5.58, 5.58, 5.58) @ 5280 MHz; Calibrated: 4/1/2020 lSensor-Surface: 1.4mm (Mechanical Surface Detection) lElectronics: DAE4 Sn1549; Calibrated: 4/4/2020 lPhantom: ELI V8.0 ; Type: QD OVA 004 AA ; Serial: 2078 lDASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) Bottom/CH 56/Area Scan (181x81x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.423 W/kg Bottom/CH 56/Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 8.435 V/m; Power Drift = -0.19 dB Peak SAR (extrapolated) = 0.674 W/kg SAR(1 g) = 0.166 W/kg; SAR(10 g) = 0.064 W/kg Maximum value of SAR (measured) = 0.371 W/kg 0 dB = 0.371 W/kg = -4.31 dBW/kg Appendix A: SAR Test Data Plots Plot No.3 Test Laboratory: Huatongwei International Inspection Co., Ltd.,SAR Lab Date: 11/6/2020 Wifi 5G U-NII-2C-Body Communication System: UID 0, Generic WIFI (0); Frequency: 5500 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5500 MHz; σ = 4.822 S/m; ε r = 35.377; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature:22.3°C;Liquid Temperature:22.1°C; DASY Configuration: lProbe: EX3DV4 - SN7494; ConvF(4.95, 4.95, 4.95) @ 5500 MHz; Calibrated: 4/1/2020 lSensor-Surface: 1.4mm (Mechanical Surface Detection) lElectronics: DAE4 Sn1549; Calibrated: 4/4/2020 lPhantom: ELI V8.0 ; Type: QD OVA 004 AA ; Serial: 2078 lDASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) Bottom/CH 100/Area Scan (181x81x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.577 W/kg Bottom/CH 100/Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 11.66 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 1.01 W/kg SAR(1 g) = 0.243 W/kg; SAR(10 g) = 0.089 W/kg Maximum value of SAR (measured) = 0.542 W/kg 0 dB = 0.542 W/kg = -2.66 dBW/kg Appendix A: SAR Test Data Plots Plot No.4 Test Laboratory: Huatongwei International Inspection Co., Ltd.,SAR Lab Date: 11/6/2020 Wifi 5G U-NII-3-Body Communication System: UID 0, Generic WIFI (0); Frequency: 5745 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 5745 MHz; σ = 5.048 S/m; ε r = 34.941; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient Temperature:22.2°C;Liquid Temperature:22.0°C; DASY Configuration: lProbe: EX3DV4 - SN7494; ConvF(4.76, 4.76, 4.76) @ 5745 MHz; Calibrated: 4/1/2020 lSensor-Surface: 1.4mm (Mechanical Surface Detection) lElectronics: DAE4 Sn1549; Calibrated: 4/4/2020 lPhantom: ELI V8.0 ; Type: QD OVA 004 AA ; Serial: 2078 lDASY52 52.10.2(1495); SEMCAD X 14.6.12(7450) Bottom/CH 149/Area Scan (181x81x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 0.411 W/kg Bottom/CH 149/Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 10.03 V/m; Power Drift = -0.18 dB Peak SAR (extrapolated) = 0.761 W/kg SAR(1 g) = 0.175 W/kg; SAR(10 g) = 0.064 W/kg Maximum value of SAR (measured) = 0.401 W/kg 0 dB = 0.401 W/kg = -3.97 dBW/kg Appendix A: SAR Test Data Plots Plot No.5

Appendix B: DAE and Probe Calibration Certificate 1 of 12 1.1. DAE4 Calibration Certificate Appendix B: DAE and Probe Calibration Certificate 2 of 12 Appendix B: DAE and Probe Calibration Certificate 3 of 12 Appendix B: DAE and Probe Calibration Certificate 4 of 12 1.2. Probe Calibration Certificate Appendix B: DAE and Probe Calibration Certificate 5 of 12 Appendix B: DAE and Probe Calibration Certificate 6 of 12 Appendix B: DAE and Probe Calibration Certificate 7 of 12 Appendix B: DAE and Probe Calibration Certificate 8 of 12 Appendix B: DAE and Probe Calibration Certificate 9 of 12 Appendix B: DAE and Probe Calibration Certificate 10 of 12 Appendix B: DAE and Probe Calibration Certificate 11 of 12 Appendix B: DAE and Probe Calibration Certificate 12 of 12

Appendix C: Dipole Calibration Certificate 1 of 26 1.1. D2450V2 Dipole Calibration Certificate Appendix C: Dipole Calibration Certificate 2 of 26 Appendix C: Dipole Calibration Certificate 3 of 26 Appendix C: Dipole Calibration Certificate 4 of 26 Appendix C: Dipole Calibration Certificate 5 of 26 Appendix C: Dipole Calibration Certificate 6 of 26 Appendix C: Dipole Calibration Certificate 7 of 26 Appendix C: Dipole Calibration Certificate 8 of 26 Appendix C: Dipole Calibration Certificate 9 of 26 Extended Dipole Calibrations Referring to KDB865664 D01, if dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Head-2450 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-05 -27.4 53.8 2.2 2019-02-03 -26.8 2.19% 52.9 0.9 1.9 0.3 2020-01-22 -27.1 1.09% 53.1 0.7 1.8 0.4 The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5ohm of prior calibration. Therefore the verification result should support extended calibration. Appendix C: Dipole Calibration Certificate 10 of 26 1.2. D5GHzV2 Dipole Calibration Certificate Appendix C: Dipole Calibration Certificate 11 of 26 Appendix C: Dipole Calibration Certificate 12 of 26 Appendix C: Dipole Calibration Certificate 13 of 26 Appendix C: Dipole Calibration Certificate 14 of 26 Appendix C: Dipole Calibration Certificate 15 of 26 Appendix C: Dipole Calibration Certificate 16 of 26 Appendix C: Dipole Calibration Certificate 17 of 26 Appendix C: Dipole Calibration Certificate 18 of 26 Appendix C: Dipole Calibration Certificate 19 of 26 Appendix C: Dipole Calibration Certificate 20 of 26 Appendix C: Dipole Calibration Certificate 21 of 26 Appendix C: Dipole Calibration Certificate 22 of 26 Appendix C: Dipole Calibration Certificate 23 of 26 Appendix C: Dipole Calibration Certificate 24 of 26 Appendix C: Dipole Calibration Certificate 25 of 26 Appendix C: Dipole Calibration Certificate 26 of 26 Extended Dipole Calibrations Referring to KDB865664 D01, if dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Head-5200 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-21 -27.9 47.8 -3.3 2019-02-20 -28.5 -2.15% 48.3 0.5 -2.9 0.4 2020-01-22 -28.3 -1.43% 47.5 0.3 -3.1 0.2 Head-5300 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-21 -34.3 48.3 0.8 2019-02-20 -33.9 1.17% 47.7 0.6 0.1 0.7 2020-01-22 -33.7 1.75% 47.5 0.8 0.5 0.3 Head-5500 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-21 -31.2 47.8 1.6 2019-02-20 -31.9 -2.24% 48.2 0.4 2.5 0.9 2020-01-22 -30.7 1.60% 47.5 0.2 2.1 0.5 Head-5600 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-21 -28.7 53.2 2.1 2019-02-20 -28.1 2.09% 52.5 0.7 2.6 0.5 2020-01-22 -27.9 2.79% 52.3 0.9 1.9 0.2 Head-5800 Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-21 -27.8 52.5 3.4 2019-02-20 -27.1 2.52% 52.1 0.4 2.9 0.5 2020-01-22 -27.2 2.16% 51.9 0.6 2.7 0.7 The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5ohm of prior calibration. Therefore the verification result should support extended calibration.

Page: 1 of 30 TEST REPORT Report No. ..................................... : CHTEW20110098 Report Verification: Project No.................................： SHT2010078801EW FCC ID ........................................... : A2HCN6Q15E Applicant’s name .......................... : Alco Electronics Ltd Address .......................................... : 11/F Metropole Square, 2 On Yiu Street, Sha Tin, New Territories, Hong Kong Test item description .................... : Notebook Computer Trade Mark ..................................... : Venturer / AVITA Model/Type reference ..................... : CN6Q15 Listed Model(s) ............................... : NS15A6, CN6QF5 Standard ........................................ : FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of receipt of test sample..........: Oct.29, 2020 Date of testing.............................: Oct.29, 2020- Nov.17, 2020 Date of issue...............................: Nov.18, 2020 Result ................. ........................: PASS Compiled by ( Position+Printed name+Signature): File administrator Echo Wei Supervised by (Position+Printed name+Signature): Project Engineer Kiki Kong Approved by (Position+Printed name+Signature): RF Manager Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address .......................................... : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW20110098 Page: 2 of 30 Issued: 2020-11-18 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V02 (2019-10) Contents 1. TEST ST AN D AR D S AND R E P O R T V E R S IO N 3 1.1. Test Standards 3 1.2. Report version 3 2. TEST DESCRIPTION 4 3. SUMMARY 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 5 3.4. Testing Laboratory Information 6 4. TEST CONFIGURATION 7 4.1. Test frequency list 7 4.2. Test mode 7 4.…

Text truncated - open the document above for the full version.