A2HRCT6378W27 inch Tablet

CT9378W2 User Manual It's important to read this instruction prior to using your new product for the first time. 7” Tablet Scan for more user manual details EN - 1 SafeTy PReCaUTionS CT9378W2 Equipment tested for compliance as a complete unit This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance (MLB International Inc., P.O. Box 1535, Buffalo, NY 14226, Tel: 516- 236-4556) could void the user’s authority to operate the equipment. Caution: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. Warning: The AC/DC adaptor is used as disconnect device. The AC/ DC adaptor of apparatus should not be obstructed OR should be easily accessed during intended used. To be completely disconnect the power input, the AC/DC adaptor of apparatus shall be disconnected from the mains. Trademark information Google Play, YouTube and other marks are trademarks of Google Inc. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance. for your Safety The AC power plug is polarized and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. Service information This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this guide. EN - 2 Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • The AC power plug is polarized and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. • Protect the power cord from being walked on or pinched par ticularly at plugs, convenience receptacles, and the point where they exit from the apparatus. • Only use attachments / accessories specified by the manufacturer. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. aDDiTionaL SafeTy infoRMaTion • The AC/DC adaptor and apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. • Always leave sufficient space around the product for ventilation. Do not place product in or on a bed, rug, in a bookcase or cabinet that may prevent air flow through vent openings. • Do not place lighted candles, cigarettes, cigars, etc. on the product. • Connect power cord only to AC power source as marked on the product. • Care should be taken so that objects do not fall into the product. • D o n o t a t t e m p t t o d i s a s s e m bl e t h e c a b i n e t . T h i s p r o d u c t d o e s n o t c o n t a i n customer serviceable components. • To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. • Do not play your headset at high volume. Hearing experts warn against extended high-volume play. iMPoRTanT SafeTy inSTRUCTionS PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE EN - 3 Switch on/Unlock Switch on and unlock: when the device is in the OFF mode, press and hold “POwER” key to enter the startup screen, then the screen is in locked mode. And press and pull the icon to the unlocke…

Text truncated - open the document above for the full version.

RCT6378W2 User Manual It's important to read this instruction prior to using your new product for the first time. 7” Tablet Scan for more user manual details EN - 1 SafeTy PReCaUTionS RCT6378W2 Equipment tested for compliance as a complete unit This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance (MLB International Inc., P.O. Box 1535, Buffalo, NY 14226, Tel: 516- 236-4556) could void the user’s authority to operate the equipment. Caution: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. Warning: The AC/DC adaptor is used as disconnect device. The AC/ DC adaptor of apparatus should not be obstructed OR should be easily accessed during intended used. To be completely disconnect the power input, the AC/DC adaptor of apparatus shall be disconnected from the mains. Trademark information Google Play, YouTube and other marks are trademarks of Google Inc. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance. for your Safety The AC power plug is polarized and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. Service information This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty included in this guide. EN - 2 Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. • The AC power plug is polarized and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. • Protect the power cord from being walked on or pinched par ticularly at plugs, convenience receptacles, and the point where they exit from the apparatus. • Only use attachments / accessories specified by the manufacturer. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. aDDiTionaL SafeTy infoRMaTion • The AC/DC adaptor and apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. • Always leave sufficient space around the product for ventilation. Do not place product in or on a bed, rug, in a bookcase or cabinet that may prevent air flow through vent openings. • Do not place lighted candles, cigarettes, cigars, etc. on the product. • Connect power cord only to AC power source as marked on the product. • Care should be taken so that objects do not fall into the product. • D o n o t a t t e m p t t o d i s a s s e m bl e t h e c a b i n e t . T h i s p r o d u c t d o e s n o t c o n t a i n customer serviceable components. • To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. • Do not play your headset at high volume. Hearing experts warn against extended high-volume play. iMPoRTanT SafeTy inSTRUCTionS PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE EN - 3 Switch on/Unlock Switch on and unlock: when the device is in the OFF mode, press and hold “POwER” key to enter the startup screen, then the screen is in locked mode. And press and pull the icon to the unloc…

Text truncated - open the document above for the full version.

55 44 33 22 11 D D C C B B A A REV: Create Date: Title:File: Page Num: Page Total: Modify Date: Block Diagram Saturday, October 23, 2010Thursday, June 20, 2013 15 3 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: Block Diagram Saturday, October 23, 2010Thursday, June 20, 2013 15 3 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: Block Diagram Saturday, October 23, 2010Thursday, June 20, 2013 15 3 1.1 SDIO1 PWR Supply UART2 I2C3 I2C2 I2S LCDC1RGB888 NAND FLASH and iNAND select one DDR3 *2512M*8Bit RK3168 32768Hz 24MHz OSC 24M 32KCLKIN DDR3 *2512M*8Bit UART0 USBOTG2.0 iNAND RESET USBHOST2.0 NANDFLASH PMIC HSIC DDRInterface CHARGE&POWERSWITCH SDIO0 HSADC USB WiFi MODULE CIF FRONT/REARCAMERA ALC5616/ES8323 LCD PANEL I2C0 I2C DEVICE DEBUG I2C1 DC JACK5V/2A BATTERY 3.7V RTC 32K CLKOUT RESET GPS Demod KEY BOARD GPIO&SARADC BATTRY DETECTOR NC Coulomb IC TOUCH PANEL&LIGHT SENSOR Audio output LCDC0RGB888 ALCO ELECTRONICS LIMITED CT9378W2 RTL8188EUS Datasheet Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller with USB Interface 5 Track ID: JATR-2265-11 Rev. 0.3 3. Application Diagram 3.1. Single-Band 11n (1x1) Solution with Single Antenna Antenna A . PA Receiver RX I/Q DAC ADC SWR/LDO Regulators 40 MHz Crystal MAC Configuration Control and Memory Ext Interface Baseband (PHY) USB2.0 Host Interface 3.3V TX I/Q 2.4 GHz Transmitter NV Memory RTL8188EUS Balun/ Filter Circuit matching Figure 1. Single-Band 11n (1x1) Solution

INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model : CT9378W2 (External) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model : CT9378W2 (External)

INTERTEK TESTING SERVICE Report No.: 13067963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal) INTERTEK TESTING SERVICE Report No.: 13070963HKG-001 FCC ID: A2HRCT6378W2 IC: 9903A-RCT6378W2 Equipment Photographs Model: CT9378W2 (Internal)

Technical Description: The Equipment Under Test (EUT) is a 7-inch Tablet with Android Operating System. The EUT equipped with a 7-inch LCD display (with touch screen), camera, USB, SD interface, loudspeaker and headphone output. The EUT contains a WiFi module complying with IEEE 802.11b/g/n(HT20)/n(HT40) standards that operating in 2.4GHz ISM frequency band (2400MHz – 2483.5MHz). The EUT is powered by an external AC/DC adaptor with 5VDC output. The adaptor accepts 100-240VAC. The applicant declared that the EUT does not contain Bluetooth RF module. An internal, integral antenna has been used. 1. WiFi module (CP318) CP318 is a WLAN USB module which fully supports the features and functional compliance of IEEE 802.11b/g/n(HT20)/n(HT40) standards. This module operates in 2.4GHz frequency bands. CP318 consists of: 1) U6 (RTL8188CUS) is a single-chip IEEE802.11b/g/n 1T1R WLAN controller with PCI (USB) interface. XTAL1 is 40MHz (crystal) clock for U6. 2. Main Processor Portion 1) U1 (RK3618) is main processor. 2) Y1 is 24MHz crystal oscillator for U1. 3. Memory Portion 1) U14 and U15 (H5TQ4G63MFR) are 4Gbit DDR3 memories. 2) U5 (TC58TEG5DCJTA00) is 4GB flash memory. Channel Occupation of CP318 WiFi Module in 802.11b/g/n standard Channel (b/g/n20) Frequency (MHz) 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457 11 2462 n20 = 802.11n HT20 (20MHz Bandwidth) Channel (n40) Frequency (MHz) 1 N/A 2 N/A 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 N/A 11 N/A n40 = 802.11n HT40 (40MHz Bandwidth) 802.11n HT40 (40MHz Bandwidth) The WiFi modules was tested in according with the following power output and in actual application the below limit shall not be exceeded. Operating Mode Nominal Radiated Field Strength Production Tolerance 802.11b 101.8dBμV/m at 3m ±3dB 802.11g 93.5dBμV/m at 3m ±3dB 802.11n (HT20) 93.4dBμV/m at 3m ±3dB 802.11n (HT40) 92.8dBμV/m at 3m ±3dB An internal, integral antenna has been used. Antenna Gain: 0dBi

RTL8188CUS-GR SINGLE-CHIP IEEE 802.11b/g/n 1T1R WLAN CONTROLLER WITH USB2.0 INTERFACE (QFN-46) DATASHEET (CONFIDENTIAL: Development Partners Only) Rev. 1.0 28 May 2010 Track ID: JATR-2265-11 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com RTL8188CUS Datasheet Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller with USB2.0 Interface (QFN-46) ii Track ID: JATR-2265-11 Rev. 1.0 COPYRIGHT ©2010 Realtek Semiconductor Corp. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of Realtek Semiconductor Corp. DISCLAIMER Realtek provides this document “as is”, without warranty of any kind. Realtek may make improvements and/or changes in this document or in the product described in this document at any time. This document could include technical inaccuracies or typographical errors. TRADEMARKS Realtek is a trademark of Realtek Semiconductor Corporation. Other names mentioned in this document are trademarks/registered trademarks of their respective owners. USING THIS DOCUMENT This document is intended for the software engineer’s reference and provides detailed programming information. Though every effort has been made to ensure that this document is current and accurate, more information may have become available subsequent to the production of this guide. REVISION HISTORY Revision Release Date Summary 1.0 2010/05/28 First release. RTL8188CUS Datasheet Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller with USB2.0 Interface (QFN-46) iii Track ID: JATR-2265-11 Rev. 1.0 Table of Contents 1. GENERAL DESCRIPTION ...............................................................................................................................................1 2. FEATURES ..........................................................................................................................................................................2 3. APPLICATION DIAGRAM ...............................................................................................................................................4 3.1. SINGLE-BAND 11N (1X1) SOLUTION (11N 1X1 MAC/BB/RF+PA) .................................................................................4 4. PIN ASSIGNMENTS ...........................................................................................................................................................5 4.1. PACKAGE IDENTIFICATION..............................................................................................................................................5 5. PIN DESCRIPTIONS ..........................................................................................................................................................6 5.1. USB TRANSCEIVER INTERFACE......................................................................................................................................6 5.2. POWER PINS....................................................................................................................................................................6 5.3. RF INTERFACE................................................................................................................................................................6 5.4. LED INTERFACE..............................................................................................................................................................7 5.5. CLOCK AND OTHER PINS.................................................................................................................................................7 6. ELECTRICAL AND THERMAL CHARACTERISTICS...............................................................................................9 6.1. TEMPERATURE LIMIT RATINGS.......................................................................................................................................9 6.2. DC CHARACTERISTICS....................................................................................................................................................9 7. MECHANICAL DIMENSIONS .......................................................................................................................................10 7.1. MECHANICAL DIMENSIONS NOTES...............................................................................................................................10 8. ORDERING INFORMATION .........................................................................................................................................11 RTL8188CUS Datasheet Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller with USB2.0 Interface (QFN-46) iv Track ID: JATR-2265-11 Rev. 1.0 List of Tables TABLE 1. USB TRANSCEIVER INTERFACE..................................................................................................................................6 TABLE 2. POWER PINS................................................................................................................................................................6 TABLE 3. RF INTERFACE............................................................................................................................................................6 TABLE 4. LED INTERFACE..........................................................................................................................................................7 TABLE 5. CLOCK AND OTHER PINS.............................................................................................................................................7 TABLE 6. TEMPERATURE LIMIT RATINGS...................................................................................................................................9 TABLE 7. DC C…

Text truncated - open the document above for the full version.

Analysis Report Report No.: 13070963HKG-001 The Equipment Under Test (EUT) is a 7-inch Tablet with Android Operating System. The EUT equipped with a 7-inch LCD display (with touch screen), camera, USB, SD interface, loudspeaker and headphone output. The EUT contains a WiFi module complying with IEEE 802.11b/g/n(HT20)/n(HT40) standards that operating in 2.4GHz ISM frequency band (2400MHz – 2483.5MHz). The EUT is powered by an external AC/DC adaptor with 5VDC output. The adaptor accepts 100-240VAC. The applicant declared that the EUT does not contain Bluetooth RF module. WiFi Antenna Type: Internal, Integral (single antenna) 802.11b, 802.11g, 802.11n (HT20): 2412MHz – 2462MHz, 11 channels, 5MHz spacing 802.11n (HT40): 2422MHz – 2452MHz, 7 channels, 5MHz spacing The WiFi modules was tested in according with the following power output and in actual application the below limit shall not be exceeded. Operating Mode Nominal Radiated Field Strength Production Tolerance Antenna Gain 802.11b 101.8dBμV/m at 3m ±3dB 0dBi 802.11g 93.5dBμV/m at 3m ±3dB 0dBi 802.11n (HT20) 93.4dBμV/m at 3m ±3dB 0dBi 802.11n (HT40) 92.8dBμV/m at 3m ±3dB 0dBi According to the KDB 447498: Based on the Maximum allowed field strength of production tolerance was 104.8dBμV/m at 3m in frequency 2.412GHz at 802.11b mode, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 9.1mW Conducted power = Radiated Power (EIRP) – Antenna Gain So; Conducted Power = 9.1mW. The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.462) mW = 9.56 mW Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

55 44 33 22 11 D D C C B B A A DCIN I2C0_SDAI2C0_SCL LED IS IS DC5V VSYS VBUS0 DC5V DC5V VBATT VSYS VBATT CHR-EN CHR-EN VBUS0 VBATT DC5V VCC_IO VBUS0 VBUS0 VBUS0 DC_DET 7 PWR_KEY 7 PWR_EN 6 PWR_HOLD 7 PMIC_PWRON 6 I2C0_SCL 10,14 I2C0_SDA 10,14 BAT_DET 7 CHG_DET 7 LCD_EN 7,12 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: DC/Charge Thursday, November 24, 2011Thursday, June 20, 2013 15 5 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: DC/Charge Thursday, November 24, 2011Thursday, June 20, 2013 15 5 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: DC/Charge Thursday, November 24, 2011Thursday, June 20, 2013 15 5 1.1 DC IN Note:Please use a 5V DC. POWER CONTROL BATTERY CHARGE No indicate Under needs above 12 milesabove 50 milesabove 30 miles PCB POWER WIRE WIDTH INDICATE above 80 miles BATTERY 2013.02.15 充电管理 R14547kR0402R14547kR0402 Q433904Q433904 1 32 Q8WPM2341SOT23Q8WPM2341SOT23 1 2 3 R1147K R0402 R1147K R0402 D4BAT54CSOT23D4BAT54CSOT23 1 3 2 D7 BAT54C/NCSOT23 D7 BAT54C/NCSOT23 1 3 2 R1062KR1062K C171uFC0402C171uFC0402 R96 8.2K%1 R96 8.2K%1 Q5SI2307SOT23Q5SI2307SOT23 1 2 3 BT13.7VBT13.7V R5 150K R0402 R5 150K R0402 D28 IN5819/NC D28 IN5819/NC 2 1 D10 SS32 SG-D1206 D10 SS32 SG-D1206 R13150K R0402 R13150K R0402 R8 1K R0402R8 1K R0402 C14 106 C0805 C14 106 C0805 D31N4148 SOD323 D31N4148 SOD323 U26 IA8056-SOP8 U26 IA8056-SOP8 TEMP 1 PROG 2 GND 3 VCC 4 BAT 5 CE 8 STDBY 6 CHRG 7 GND 9 R105 0R R0402 R105 0R R0402 J3 2DC-A245-J03 J3 2DC-A245-J03 132 4 5 C180.1uFC0402C180.1uFC0402 R1461kR0402R1461kR0402 R3150KR0402R3150KR0402 R29 0R R0402 R29 0R R0402 D5BAT54C/NCSOT23D5BAT54C/NCSOT23 1 3 2 D27 IN5819/NC D27 IN5819/NC 2 1 R715KR0402R715KR0402 R7910KR7910K R98 2.2K R98 2.2K R28200K%1R0402R28200K%1R0402 R170 10K R170 10K R4 10K R0402 R4 10K R0402 R10 51K/NC R10 51K/NC R95 910%1 R95 910%1 C62.2uFC0603C62.2uFC0603 D8 1N4148 SOD323 D8 1N4148 SOD323 C11uFC0402C11uFC0402 D20 IN5819 D20 IN5819 2 1 D6 SS32 SMD_1N4001/N D6 SS32 SMD_1N4001/N R30120K%1R0402R30120K%1R0402 R2 47K R0402 R2 47K R0402 PWR SW6 TS-1100E PWR SW6 TS-1100E 1 1 2 2 3 3 4 4 Q423904Q423904 1 32 D37 IN4148SOD323 D37 IN4148SOD323 Q11 3904 Q11 3904 1 32 Q28050/NCSOT23Q28050/NCSOT23 1 32 R610KR0402R610KR0402 ED39NC/ESD9B5VE0402NED39NC/ESD9B5VE0402N R99 10K R99 10K C49 105 C0402 C49 105 C0402 R12 1K R0402 R12 1K R0402 ALCO ELECTRONICS LIMITED CT9378W2 55 44 33 22 11 D D C C B B A A RESET VDD_FB PWR_EN AVDD_COM VCC_IO VCC_18VCC28_CIF VSYS VCC_IO VSYS VCC_IO VCC_SD VSYS VDD_11 VCC_TP VCC18_CIFVCC_RTC VCCA_30 VSYSVSYS VCC_RTC VCC_IO VSYSVSYS VCC_IO VSYS VDD_LOG VDD_LOG VCC_DDR VDD_ARM PMIC_PWRON 5 RTC_CLKOUT 7 RESET 7 DVS0_CTL 10 PMIC_SLEEP 7 PMIC_INT 7 I2C1_SCL 10 I2C1_SDA 10 PWR_EN 5 AVDD_COM 10 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: System power Tuesday, November 29, 2011Thursday, June 20, 2013 15 6 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: System power Tuesday, November 29, 2011Thursday, June 20, 2013 15 6 1.1 REV: Create Date: Title:File: Page Num: Page Total: Modify Date: System power Tuesday, November 29, 2011Thursday, June 20, 2013 15 6 1.1 SYSTEM POWER above 30 milesabove 50 milesabove 12 miles Under needs No indicate above 80 miles PCB POWER WIRE WIDTH INDICATE 2013.02.15 2013.02.15 SHIELD5CON5SHIELD-3PSHIELD5CON5SHIELD-3P 1 2 3 32.768K32.768K C62 NC C0402 C62 NC C0402 C121 10uF C0805 C121 10uF C0805 U12 SY8008/PT3406SOT26 U12 SY8008/PT3406SOT26 EN 1 GND 2 LX 3 VIN 4 FB/OUT 6 NC 5 R166100RR0402R166100RR0402 SHIELD6CON5SHIELD-3PSHIELD6CON5SHIELD-3P 1 2 3 C78 4.7uF C0603 C78 4.7uF C0603 C63 12pF C0402 C63 12pF C0402 C5910uFC0805C5910uFC0805 C30.1uFC0402C30.1uFC0402 L62.2uH/2AIND-4X4L62.2uH/2AIND-4X4 Y3 32.768K CRY-MC146 Y3 32.768K CRY-MC146 T1MARKT1MARK 1 SHIELD7CON5SHIELD-3PSHIELD7CON5SHIELD-3P 1 2 3 C125 4.7uF C0603 C125 4.7uF C0603 C182NCC0402C182NCC0402 T2MARKT2MARK 1 C155 4.7uF C0402 C155 4.7uF C0402 SHIELD8CON5SHIELD-3PSHIELD8CON5SHIELD-3P 1 2 3 C7622uFC0805C7622uFC0805 C65 4.7uF C0805 C65 4.7uF C0805 T3MARKT3MARK 1 SHIELD9CON5SHIELD-3PSHIELD9CON5SHIELD-3P 1 2 3 C126 4.7uF C0603 C126 4.7uF C0603 C12810uF C0805 C12810uF C0805 T4MARKT4MARK 1 ED40 NC/ESD9B5V E0402n ED40 NC/ESD9B5V E0402n L103.3uH/1AIND_3X3L103.3uH/1AIND_3X3 R391KR0402R391KR0402 SHIELD10CON5SHIELD-3PSHIELD10CON5SHIELD-3P 1 2 3 SHIELD2 CON5 SHIELD-3PSHIELD2 CON5 SHIELD-3P 1 2 3 T5MARKT5MARK 1 R38 100R R0402 R38 100R R0402 C113 4.7uF C0603 C113 4.7uF C0603 C60 2.2uF C0402 C60 2.2uF C0402 C64 12pF C0402 C64 12pF C0402 C8022uFC0805C8022uFC0805 T9MARKT9MARK 1 RESETSW2TS-1187RESETSW2TS-1187 1 1 3 3 2 2 4 4 C199100pFC0402C199100pFC0402 SHIELD3CON5SHIELD-3PSHIELD3CON5SHIELD-3P 1 2 3 R17 100K%1 R0402R17 100K%1 R0402 L42.2uH/1AIND_3X3L42.2uH/1AIND_3X3 C77 1uF C0402 C77 1uF C0402 C51 1uF C0402 C51 1uF C0402 U11 TPS659102 PMUTPS6591001 U11 TPS659102 PMUTPS6591001 PWRHOLD 1 VAUX33 4 VDIG2 5 VDIG1 7 SCL 9 VCC6 6 SDASR/EN2 10 VCC3 3 SCLSR/EN1 11 VMMC 2 SDA 8 VDDIO 12 VCCIO 13 SWIO 14 GNDIO 15 VFBIO 16 REFGND 17 VREF 18 BOOT1 19 OSC32KIN 20 OSC32KOUT 21 VDAC 22 VCC5 23 VPLL 24 TESTV 25 BOOT0 26 VBACKUP 27 VCC7 28 VRRTC 29 VFB3 30 SW3 31 VFB1 32 PWRON 33 GND1 34 SW1 35 VCC1 36 SLEEP 37 CLK32KOUT 38 GPIO/CKSYN 39 NRESPWRON 40 VCC2 41 SW2 42 GND2 43 VFB2 44 INT1 45 VAUX1 46 VCC4 47 VAUX2 48 PowerPAD 49 C70 4.7uF C0402 C70 4.7uF C0402 R14 4K7 R0402 R14 4K7 R0402 R42150K%1R0402R42150K%1R0402 C2 1uF C0402 C2 1uF C0402 C107 1uFC0402 C107 1uFC0402 C61 0.1uF C0402 C61 0.1uF C0402 C115 4.7uF C0603 C115 4.7uF C0603 C5NCC0402C5NCC0402 C4 4.7uFC0603 C4 4.7uFC0603 C71nFC0402C71nFC0402 SHIELD4CON5SHIELD-3PSHIELD4CON5SHIELD-3P 1 2 3 C181 NC C0402 C181 NC C0402 C4010uFC0805C4010uFC0…

Text truncated - open the document above for the full version.