A2HRS2867B5 Disc Audio System

RS2867B User Manual Manual del usuario It's important to read this instruction prior to using your new product for the fi rst time. Es importante que lea este libro de instrucciones antes de usar su nuevo producto por primera vez. It's important to read this instruction prior to using your new product for the fi rst time. Es importante que lea este libro de instrucciones antes de usar su nuevo producto por primera vez. EN-2 SAFETY PRECAUTIONS CLASS 1 LASER PRODUCT This product contains a low power laser device. THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT. Caution: This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. Do not open covers and do not repair yourself. Refer servicing to qualified personnel. WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. WARNING : MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SHOULD REMAIN READILY OPERABLE DURING INTENDED USE. IN ORDER TO DISCONNECT THE MAINS PLUG FROM MAINS COMPLETELY, THE MAINS PLUG SHOULD BE DISCONNECTED FROM THE MAINS SOCKET OUTLET COMPLETELY. SEE MARKING ON BOTTOM / BACK OF PRODUCT CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAN ICES-3(B) / NMB-3(B) This device complies with Industry Canada Licence-exempt RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. EN-3 Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat. • Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet. • Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. • Only use attachments / accessories specifi ed by the manufacturer. • Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. • Unplug this apparatus during lightning storms or when unused for long periods of time. • Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. ADDITIONAL SAFETY INFORMATION • Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE For Your Safety The AC power plug is polarized (one blade is wider than the other) and only fits into AC power outlets one way. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the o…

Text truncated - open the document above for the full version.

(IC602) (IC401) (IC301) (X1) USB charger (Q702) ME2325 (U602) (X601) 16MHz (X1) (U1, U2) 32.768kHz 2402MHz - 2480MHzPCB Trace Antenna Power Amplifier TAS5611 IC4 MCU NE2532 IC3 IC1 SC9258 Driver IC7 SC9640 CD Servo IC13 SA9614 8.4672MHz X3 32.768kHz (X4) FM Tuner RDA5807M IC12 DC 33V Volume Control IC TDA7440D IC9 DC 9V WLIS04 FM Tuner Antenna &U\VW 2402-2480MHz U1 X1 U2 WLIS04 Block Diagram              !    "                       !      "#  $ %"    %! #&'  $   ## ! 2402MHz - 2480MHz PCB trace Abtenna 16MHz

INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model : CD2767BE (External)

CD2767BE (RS2867B) back cover Printing: BLACK Date: 2014-01-20 CLASS 1 LASER PRODUCT APPAREIL À LASER DE CLASSE 1 PRODUCTO LASER DE CLASE 1 SPEAKERS WARNING: CONNECTING SPEAKERS OTHER THAN THE SPEAKERS SUPPLIED WITH THE UNIT, MAY DAMAGE THE UNIT. AVERTISSEMENT: LE RACCORDEMENT D’ENCEINTES AUTRES QUE CELLES FOURNIES AVEC L’APPAREIL PEUT L’ENDOMMAGER. WARNING: DANGEROUS HIGH VOLTAGE INSIDE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. AVERTISSEMENT: HAUTE TENSION DANGEREUSE À L'INTÉRIEUR. POUR RÉDUIRE LE RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ. NE RETIREZ PAS LE COUVERCLE. AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR À L’INTÉRIEUR. CONFIEZ LES RÉPARATIONS À UN TECHNICIEN QUALIFIÉ. CAUTION: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE TO BEAM. ATTENTION: RADIATION INVISIBLES DU LASER EN CAS D'OUVERTURE ET DE DÉFAILLANCE OU DE MISE HORS SERVICE DU DISPOSITIF DE VERROUILLAGE. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU. THIS PRODUCT COMPLIES WITH DHHS RULES 21 SUBCHAPTER J PARTS 1040-10 AND 1040-11 AT DATE OF MANUFACTURED. CAN ICES-3(B) / NMB-3(B) THIS PRODUCT COMPLIES WITH DHHS RULES 21 SUBCHAPTER J PARTS 1040-10 AND 1040-11 AT DATE OF MANUFACTURED. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-3(B) / NMB-3(B) AVC Multimedia Markham, Ontario L3R 1E3 MADE IN CHINA / FABRIQUÉ EN CHINE / FABRICADO EN CHINA Model: RS2867B Model: RS2867B AC 120V 60Hz 38W USB terminal: 5V 500mA FCC ID: A2HRS2867B IC: 9903A-RS2867B THIS PRODUCT COMPLIES WITH DHHS RULES 21 SUBCHAPTER J PARTS 1040-10 AND 1040-11 AT DATE OF MANUFACTURED. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-3(B) / NMB-3(B) AVC Multimedia Markham, Ontario L3R 1E3 MADE IN CHINA / FABRIQUÉ EN CHINE / FABRICADO EN CHINA AC 120V 60Hz 38W USB terminal: 5V 500mA FCC ID: A2HRS2867B IC: 9903A-RS2867B AC 120V 60Hz 38W USB terminal: 5V 500mA FCC ID: A2HRS2867B IC: 9903A-RS2867B THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. MADE IN CHINA / FABRIQUÉ EN CHINE / FABRICADO EN CHINA SERIAL NO./DATE CODE/CARB LABEL(COMPUTER LABEL) Size: 48x28mm (combined CARB label and SN/date code label, for reference only) AVC Multimedia 01/2014 CARB 93120 Compliant for Formaldehyde ------------------------------------- MANUFACTURED: January 2014 .S/N: JA151DRW0001 Model: CD2767BE Venturer Electronics Inc. Markham, Ontario L3R 1B8

INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal) INTERTEK TESTING SERVICE Report No.: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Equipment Photographs Model: CD2767BE (Internal)

CD2767BE TECHNICAL DESCRIPTION This unit is powered by an AC-DC converter with 120V AC input. After some necessary regulator circuits, then distribute the power supply to MCU (IC3 NF2532), CD system (IC1, IC7, IC13), Bluetooth Module (WLIS04), FM tuner (IC12 RDA5807M), Volume control IC (IC9 TDA7440D), Power amplifier (IC4 TAS5611), and USB charger (Q702 ME2325) respectively. 8.4672MHz crystal (X3) is clock for digital audio while two 32.768kHz crystals (X1, X4) are for MCU (IC3) and FM tunerr (IC12). CD mode: When starting up the unit, the software defaults to CD function. MCU issues a Command to start up CD and go into CD mode, also enables the Volume Control IC to work in CD Channel, through CD Mechanism to read and get the data of CD R/RW Disc, and after data processing by MCU, output L&R channel audio signals, and performing volume and EQ control by Volume Control IC, then output to Power Amplifier for amplifying the audio signal and drive the external Speakers. Radio mode: Input MCU command by Keyboard and turn to Radio Receiver, and turn on the power supply of Radio Receiver, also enables the Volume Control IC to work in Radio Channel. The clock frequency of Radio Receiver is 32.768kHz. It will convert the radio high frequency signals was received into audio signals, and output through the Radio channel of Volume Control IC, then via Power Amplifier to the external Speakers. Bluetooth mode: (WLIS04) 16MHz crystal (X1) provides clock for Bluetooth RF IC (U1 IS1681S). U2 (24C32) is serial EEPROM for parameter backup of Bluetooth RF IC (U1 IS1681S). Input MCU command by Keyboard, switch to Bluetooth mode, and enables MCU to issue a Command to start up the Bluetooth Module, Volume control IC, power supply of the Power amplifier, and make Volume control IC turn to work in Bluetooth Channel. The Bluetooth Module use a PCB antenna, the clock frequency is 16MHz, and works in the band of 2.4GHz, within the frequency range of 2.402GHz ～ 2.480GHz, Modulation type is GFSK, Modulation type is GFSK. The Bluetooth Module will demodulate the Bluetooth RF signals into to Audio signals, and output to the Power Amplifier for amplifying through the Bluetooth Channel of Volume Control IC, and then drives the Speakers by the Amplifier. Aux mode: Input the command into the MCU by keyboard, and switch to AUX mode. External Audio signal input to Volume Control IC via 3.5MM Jack for volume and EQ control, and output Audio Signal to Power Amplifier for amplifying, and then drives the Speakers by the Amplifier. USB Changer: Supply 5V from AC/DC converter, and charge to the external device through USB 2.0 Jack. BlueTooth Module Modulation Type: GFSK Antenna Type: Integral, Internal (PCB Trace) Frequency Range: 2402MHz - 2480MHz, 1MHz channel spacing, 79 channels Antenna Gain: 0dBi Nominal rated field strength: 100.6dBμV/m at 3m Maximum allowed field strength of production tolerance: +/- 3dB Channel Frequency Table of Bluetooth Module WLINK TECHNOLOGY LTD. Product Specification __________________________________________________________________________________ ___________________________________________________________________________________________ Page 1 of 7 Taiwan H/Q Add.: No.46, Aly. 108-3 , Ln. 445 , Sec. 2, Meishi Rd., Yangmei City, Taoyuan County 326, Taiwan (R.O.C.) Tel: +886-3-4811534 Features： Bluetooth 3.0+EDR Stereo Audio module ● Bluetooth 3.0+EDR compliant ● Typical +2dBm Class 2 output power Version: 1.0 ● Receiver Sensitivity: GFSK typical -91dBm, π/4 PSK typical Jan 2013 -92dBm, 8DPSK typical -84dBm ● Audio DAC: 94dB SNR ● Build in Max. 250mAH Li-ion battery charging circuit ● HSP, A2DP, AVRCP profile support ● SBC decode for Bluetooth audio streaming ● Voice prompt ● Build in Line in interface ● NFC support ● EQ control ● Size: 23mm x 14mm Product Description: The WLIS04-ST is a highly integrated Bluetooth 3.0+EDR stereo module, des igned for high data rate, short-range wireless communication in the 2.4 GHz ISM band. With ISSC Bluetooth stack and profile, the WLIS04-ST provides a low power and ultra-low cost Bluetooth 3.0+EDRsolution for wi reless voice/audio applications. Applications: ●High quality stereo speaker and HiFi ●High quality wireless stereo audio receiver WLINK TECHNOLOGY LTD. Product Specification __________________________________________________________________________________ ___________________________________________________________________________________________ Page 2 of 7 Taiwan H/Q Add.: No.46, Aly. 108-3 , Ln. 445 , Sec. 2, Meishi Rd., Yangmei City, Taoyuan County 326, Taiwan (R.O.C.) Tel: +886-3-4811534 Outline Dimension & Pin Definition: Pin No. I/O Name Description 1 P P30 GPIO, default pull-high input Line-in detection, 1: no line-in detected; 0: line-in detected 2 I/O P20 GPIO, default pull-high input System Configuration, H: Application; L: Baseband(IBDK Mode) 3 I/O P00 GPIO, default , pull-low input. Slide Switch Detector 4 I/O P04 GPIO, default pull-high input Audio AMP Enable/NFC detect 5 AO SPKR R-channel analog headphone output, single-ended application only 6 AO AOHPM Headphone common mode output/sense input 7 AO SPKL L-channel analog headphone output, single-ended application only 8 P VDDAO Positive power supply dedicated to CODEC output amplifiers 9 P GND Ground 10 NC 11 NC 12 NC 13 AI AIR Stereo analog line in, R-channel 14 AI AIL Stereo analog line in, L-channel 15 I/O RST_N System Reset Pin 16 P GND Ground 17 P ADAP_IN Power adaptor input 18 P BAT_IN Battery input 19 P SYS_PW System Power Output 20 I/O SK1/P35 Default SAR input for battery detection This pin can be re-defined as GPIO3_5 21 P BK_OUT Buck feedback sense pin 22 P GND Ground 23 P MFB Multi-Function Push Button key Combined Play/Panse key when A2DP enabled. 24 P LED1 LED Driver 1 25 P LED2 LED Driver 2 26 I/O P02 GPIO, default pull-high input PLAY/PAUSE button WLINK TECHNOLOGY LTD. Product Specification __________________________________________________________________________________ __…

Text truncated - open the document above for the full version.

Analysis Report Report No.: 14010277HKG-002 The Equipment Under Test (EUT) is a 5 Disc Audio System that can accept audio sources including 5 CD changer, FM Tuner, analog line-in and Bluetooth devices. The Bluetooth module in the EUT is operating in the frequency range from 2402MHz to 2480MHz (79 channels with 1MHz channel spacing). The audio signal is amplified and fed to the supplied passive external stereo loudspeakers. The EUT contains a headphone output and a USB port (for 5V DC changing purpose only). The EUT is powered by 100-120VAC. Antenna Type: Internal integral antenna Antenna Gain: 0dBi Nominal rated field strength: 100.6dBμV/m at 3m Maximum allowed field strength of production tolerance: +/- 3dB According to the KDB 447498: Based on the Maximum allowed field strength of production tolerance was 103.6dBμV/m at 3m in frequency 2.4GHz, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 6.87mW Conducted power = Radiated Power (EIRP) – Antenna Gain So; Conducted Power = 6.87mW. The conducted source-based time-averaged output power = (6.87 *5/6 ) mW = 5.725 mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the above conducted source-based time-averaged output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing.

Audio Amplifier Portion Bluetooth2402MHz - 2480MHz 16MHz Key and Display Portion MODEL: VER: DESIGN: APPROVED: TITLE: PAGE: SHENZHEN ACT INDUSTARIAL CO.,LTDDATESIGNATUREBYREASONVER #22 L=200mm +5.1V -25V STBY-CT GND GND GND +12V -25V GND GND +33V +33V +33V F+3.3V F-3.3V 5.1V 5.1V GND GND +5.1V F+3.3V F-3.3V A/0㄀ϔ⃵ϟথ ⃻䰇ᬜᯢ ⃻䰇ᬜᯢ2013-12-31CD2767BE V1.0 CD2767BE V1.0 SCH-1 A/01 OF 1 L N CN1 AC IN:100-132V DIP2 CY5102 250VCY4102 250V THR1 1.3D-13 CX1 NC CY1NCCY2NC LF1 1.0mH CX2 0.47uF/275VAC LF2 30mH BD1 KBL406 C1 180UF200V C2 180UF200V C66 680uF/50V C69 680uF/50V D17 1N4148 D39 1N4007 D20 FR207 D43 FR107 D22 RL207 D401N4007 D42 FR207 D45 FR207 D48 NC D47 SR5100 D33 NC D54 SR360 D34 FR103 D55 1N4148 D49 NC D50 SR560 D58 1N4148 U12 TL431A U13 TL431A C36 104/50V C44 104/50V C72 122/100V C75 681/50V C60 222/1KV C62 102/1KV C70 104/50V C61 222/1KV C43 104/50V C64 102/1KV CY3 222/400V C59 56/1KV C54 101P/1KV C63 102/1KV U1 EL817 U2 EL817 U3 EL817 R111 18K 1% R112 22R R151 10K R114 270R R23 1.3R R123 10R R117 1K R124 2.7K R125 3.6K R127 15K R129 1K R131 10K R45 82K R13430K R141 100K R169 18K R157 1.2R R158 100R R160 NC R159 220R R162 10K R170 22R R130 5.1K R74 NC R163 15K R103 NC R104 NC R13 NC R31 NC R113 0R R171 22R R172 47R R173 47R R101 NC R98 NC R174 330R R75 10K R126 10K R119 30K R43 NC R144 100K R143 100K R142 100K R102 82K R177 5.1K R176 NC R179 330R R138 10K R122 1K R148 2.4R R149 4.7R R147A 4.7R R147 NC R9 NC JP2 D0.6MM 1 FB 2 SS 3 IS 4 RT/CT 5 GND 6 OUT 7 VCC 8 VREF U8 FAN7554 C53 22uF/50V C48 1uF/50V C87 10uF/50V C86 10uF/50V C79 820uF/10V C78 10uF/50V C77 100uF/35V C91 680uF/16V C90 680uF/16V C83 680uF/10V C92 680uF/16V C73 10uF/50V C18 NC ZD10 5.6V ZD8 20V ZD12 15V ZD11 5.1V ZD9 18V ZD1 22V L4 CORE L12 CORE L13 CORE L7 CORE 31 2 Q18 2N5551 3 1 2 Q19 2N5551 3 1 2 Q20 2N5551 31 2 Q16 2N5551 L18 2uH L15 2uH D46 1N4148 D35 FR103 D38 1N4007 D59 1N4148 C84 472/50V C88 104/50V C89 104/50V C67 104/50V C68 104/50V ZD13 NC C98 104/50V C99 104/50V C100C 104/50V 1 2 3 4 5 6 7 8 9 T1 C80 680uF/16V C93 680uF/16V L16 2uH C3 10uF/50V R6 68K Q1 7N65 R7 10K 1 2 3 4 5 6 7 8 9 10 11 12 T2 EEL22-T015 1 2 3 4 5 6 2.5mm 1 2 3 4 5 6 7 CN2 1 2 3 4 5 6 7 8 9 CN4 R8 1K R10 10K 3 1 2 Q2 2N5551 C5 104/50V R11 1K C4 NC F1 T5AL 250V R1 1.5M R2 1.5M R3 1.5M R4 1.5M C6 104/50V 3 1 2 Q4 NC ZD3 NC R12 NC R14 NC R15 NC C7 NC D31 8A/400V MOV1 NC ZD4 NC 1234 8 76 5 U4 DIP8 PN8149 R16 2R R17 2R R18 1.5R R19 1.5R Q5 2SB649 C8 100uF/35V C9 NC ZD5 NC ZD6 27V C10 NC C65 NC R21 1.3R R20 1.3R R22 1.3R GND GND GND GND GND GND GND GND PGND PGND PGND PGND PGND PGND PGND Power Supply Portion

lntertek Valued Qualìty. Dslivered. lssuing Laboratory: lntertek Testing Services Hong Kong Limited Hong Kong Accroditation Servicê (HKAS) has accredited th¡s lsboratory under th€ Hong Kong Laboratory Accreditat¡on Scheme (HOKLAS) for spec¡lic laboratory activit¡es ss l¡stod in the HOKLAS directory of accredited laboratories. The rssultl shown in this report were detemined by this laboratory in accordance with its terms of accr€ditat¡on. TEST REPORT Report No. : 1 401 0277HKG-002 ALCO Electronics Ltd. Application For Certification (Original Grant) (FCC lD: A2HRS2867B) (lC: 9903A-RS28678) Transceiver tEsl Prepared and Checked by: Th€ losl r6pol only sllows to be rev¡sgd wilhin lhe r€lont¡on period unless iudhgr slandard or the requiremgnt ms nol¡ced. This rôport ¡s for lh6 exclus¡ve uso ol lntertek'g Cl¡enl and ¡s providgd pursusnt to the agreomeni belwen lnl6rtek ond ¡lr Cl¡€nl. lnl€rt€k,s responsibil¡ty snd liãbility ãre lim¡t€d lo th6 têrms and condil¡ons of lh6 egreemonl. lnterlek assumôs no iabil¡ty to Eny party, othêr then to thô cliont ¡n sccordânce wiíh lh6 agreement, for any loss, expenso or damage.occâsioned by th6,us6 of lh¡s ropoñ, Only the Cli6nl ie autiorizeï to pemit copy¡ng or d¡slribulion ot ffris repòrt ano then only in ilg enl¡r€ty. Any usg of lh€ lntertek nam or one of ¡ts marke foi ths sal; or sdvort¡sement ol lho lsiled matåriallprocuct or gery¡"ã musi nr"i6" approvod in wiling by lntertek. Th6 obserysl¡ons snd test ßsulls in th¡s reporl sre r€levant only lo the semplê test€d This r6porl by ¡ts€ll doss not ¡mply thal th€ male¡ial, producl, or s6ry¡æ ¡9 or has ovgr b€6n undor an lnlertek ærtifcaliôn progmm lntertek Testing Services Hong Kong Ltd. 2/F., Gsrment Centro, 576 Caslle peak Road, Kowloon, Hong Kong. Tel:(852)21738888 Fax:(852127855487 Website:\¡vw.hk.intertek-etlsemko.com Approved by: Supervisor Date: March 03,2014 Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 14010277HKG-002 i FCC ID: A2HRS2867B IC: 9903A-RS2867B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com GENERAL INFORMATION ALCO Electronics Ltd. BRAND NAME: VENTURER, MODEL: CD2767BE BRAND NAME: RCA, MODEL: RS2867B FCC ID: A2HRS2867B IC: 9903A-RS2867B Grantee: ALCO Electronics Ltd. Grantee Address: 11/F., Zung Fu Industrial Building, 1067 King’s Road, Quarry Bay, Hong Kong. Contact Person: Peggy Suen Tel: 852-2562 6121 Fax: 852-2597 5201 e-mail: [email protected] Manufacturer: Dongguan Houjie Alco Electronics General Factory Manufacturer Address: Gong Ye Xi Road, Houjie Technology Industrial Park, Houjie, Dongguan, Guangdong P.R.C. 523960 China Brand Name: VENTURER / RCA Model: CD2767BE / RS2867B Type of EUT: Transceiver Description of EUT: 5 Disc Audio System Serial Number: N/A FCC ID / IC: A2HRS2867B / 9903A-RS2867B Date of Sample Submitted: January 07, 2014 Date of Test: January 07, 2014 to February 27, 2014 Report No.: 14010277HKG-002 Report Date: March 03, 2014 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 14010277HKG-002 ii FCC ID: A2HRS2867B IC: 9903A-RS2867B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com SUMMARY OF TEST RESULT ALCO Electronics Ltd. BRAND NAME: VENTURER, MODEL: CD2767BE BRAND NAME: RCA, MODEL: RS2867B FCC ID: A2HRS2867B IC: 9903A-RS2867B TEST SPECIFICATION REFERENCE RESULTS Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.4 Pass Transmitter Field Strength and Bandedge Requirement 15.249 / RSS-210 A2.9 Pass Radiated Emission in Restricted Bands 15.205 / RSS-210 2.2 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2012 Edition RSS-210 Issue 8, December 2010 RSS-Gen Issue 3, December 2010 Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Issuing Laboratory: Intertek Testing Services Hong Kong Limited Hong Kong Accreditation Service (HKAS) has accredited this laboratory under the Hong Kong Laboratory Accreditation Scheme (HOKLAS) for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. The results shown in this report were determined by this laboratory in accordance with its terms of accreditation. Report No.: 14010277HKG-002 iii FCC ID: A2HRS2867B IC: 9903A-RS2867B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Table of Contents 1.0 General Description...................................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Configuration Photographs Worst-Case Radiated Emissions (Front View) Model: CD2767BE 14010277HKG-002 CD2767BE Side A INTERTEK TESTING SERVICE Report No: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B Configuration Photographs Worst-Case Radiated Emissions (Rear View) Model: CD2767BE 14010277HKG-002 CD2767BE Side B

INTERTEK TESTING SERVICE Report No: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B i Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) Model: CD2767BE INTERTEK TESTING SERVICE Report No: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B ii Configuration Photographs Worst-Case Line-Conducted Emissions (Rear View) Model: CD2767BE INTERTEK TESTING SERVICE Report No: 14010277HKG-002 FCC ID: A2HRS2867B IC: 9903A-RS2867B iii Configuration Photographs Worst-Case Line-Conducted Emissions (Side View) Model: CD2767BE