A2HSPS3688BKitchen Radio

KLR33688B EN - FR User manual Manuel de l’utilisateur It is important to read this instruction book prior to using your new product for the first time. Il est important de lire ce manuel d’utilisation avant l’utilisation initiale de ce nouveau produit. EN - FR - 2 Safety Precautions FCC InFormatIon This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING: • Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • The AC adapter is used as disconnect device and it should remain readily operable during intended used. In order to disconnect the unit from the mains completely, the AC adapter should be disconnected from the mains socket outlet completely. • The AC adapter of unit should not be obstructed OR should be easily accessed during intended use. • Minimum 10 cm (4 inches) distances around the unit for sufficient ventilations. • The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains, etc. • No naked flame sources such as lighted candles should be placed on the unit. on SaFety • Disconnect the AC adapter immediately if liquid spills into or onto the unit, or if an object falls into the unit. The unit should not be used until service by a qualified service personnel is completed. • The unit shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall be placed on the unit. on USe Never use the unit where it would be subject to: - Heat sources such as radiators or air ducts. - Direct sunlight. For CUStomerS In Canada This apparatus complies with the Class B limits for radio noise emission set out in radio interference regulations. CAN ICES-3 (B) / NMB-3 (B) CaUtIon TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY HEATING OR COOKING APPARATUS BENEATH THIS UNIT. This device complies with Industry Canada Licence-exempt RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. EN - FR - 3 tooLS needed: 1) Electric drill with 1/4” bit; 2) Phillips-head (cross style) screwdriver. SteP 1 If your cabinet does not have an overhang: a) Place the Mounting Template in the desired location inside or underneath the cabinet (whichever has less obstructions, and will be easier for you to reach to drill holes), flush with the front edge of the cabinet and tape it down. Go to STEP 2. If your cabinet doeS have an overhang: a) Measure the thickness “T” of the cabinet overhang (see Figure 1). b) Fold the Mounting Template along the guideline that is closest to the thickness of your cabinet overhang. c) Tape Mounting Template to the underside of the cabinet with the folded portion of the Mounting Template flush up against the cabinet overhang (see Figure 2). Go to STEP 2. SteP 2 Use an electric drill with a ¼” drill bit (not included) to drill all three holes marked on the Mounting Template (see Figure 3). To reduce splintering, place a small piece of masking tape over each hole location before drilling. Go to STEP 3. SteP 3 If your cabinet does not have an overhang: a) SIX screws are included with this unit, but you will only need three of them. Select the screw length which will go completely through your cabinet bottom, and provide at least 3/8” of thread to screw into the unit. b) Insert the three selected screws through each hole from the inside of the cabinet going down (see Figure 4). Warning: Please follow the steps below for proper mounting: 1. We recommend you install the 3 screws using hand tools. Do not use power tools because high torque can damage the threads on the main unit. 2. Please hold and support the unit before you insert any of the screws. 3. First mount 2 screws on opposite corners of the unit. c) Hold the unit up against the bottom of the cabinet, and align the three holes on the top of the unit with the screws. Partially tighten each screw, but do not fully tighten the screws until all of them have been started. d) Gently tighten each screw until they are firmly holding the unit in place. mounting Instructions EN - FR - 4 If your cabinet doeS have an overhang: a) SIX screws are included with this unit, but you will only need three of them. Select the screw length which will go completely through your cabinet bottom, and extend at least 3/8” past the bottom of your cabinet overhang. b) This unit includes two sets of three spacers of various lengths. The spacers can be put together to form longer spacers to accommodate var…

Text truncated - open the document above for the full version.

SPS3688B User manual Manual del Usuario Manuel de l’utilisateur It is important to read this instruction book prior to using your new product for the first time. Es importante que lea este libro de instrucciones antes de comenzar a usar su nuevo producto. Il est important de lire ce manuel d’utilisation avant l’utilisation initiale de ce nouveau produit. Scan for more user manual details or visit www.RCAav.com Consulte para obtener más detalles del manual del usuario o visite www.RCAav.com Scanner pour détails supplémentaires indiqués dans le manuel d’utilisation ou visiter www.RCAav.com EN - ES - FR EN - ES - FR - 2 Safety Precautions FCC InFormatIon This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING: • Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • The AC adapter is used as disconnect device and it should remain readily operable during intended used. In order to disconnect the unit from the mains completely, the AC adapter should be disconnected from the mains socket outlet completely. • The AC adapter of unit should not be obstructed OR should be easily accessed during intended use. • Minimum 10 cm (4 inches) distances around the unit for sufficient ventilations. • The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains, etc. • No naked flame sources such as lighted candles should be placed on the unit. on SaFety • Disconnect the AC adapter immediately if liquid spills into or onto the unit, or if an object falls into the unit. The unit should not be used until service by a qualified service personnel is completed. • The unit shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall be placed on the unit. on USe Never use the unit where it would be subject to: - Heat sources such as radiators or air ducts. - Direct sunlight. For CUStomerS In Canada This apparatus complies with the Class B limits for radio noise emission set out in radio interference regulations. CAN ICES-3 (B) / NMB-3 (B) CaUtIon TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY HEATING OR COOKING APPARATUS BENEATH THIS UNIT. This device complies with Industry Canada Licence-exempt RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. EN - ES - FR - 3 tooLS needed: 1) Electric drill with 1/4” bit; 2) Phillips-head (cross style) screwdriver. SteP 1 If your cabinet does not have an overhang: a) Place the Mounting Template in the desired location inside or underneath the cabinet (whichever has less obstructions, and will be easier for you to reach to drill holes), flush with the front edge of the cabinet and tape it down. Go to STEP 2. If your cabinet doeS have an overhang: a) Measure the thickness “T” of the cabinet overhang (see Figure 1). b) Fold the Mounting Template along the guideline that is closest to the thickness of your cabinet overhang. c) Tape Mounting Template to the underside of the cabinet with the folded portion of the Mounting Template flush up against the cabinet overhang (see Figure 2). Go to STEP 2. SteP 2 Use an electric drill with a ¼” drill bit (not included) to drill all three holes marked on the Mounting Template (see Figure 3). To reduce splintering, place a small piece of masking tape over each hole location before drilling. Go to STEP 3. SteP 3 If your cabinet does not have an overhang: a) SIX screws are included with this unit, but you will only need three of them. Select the screw length which will go completely through your cabinet bottom, and provide at least 3/8” of thread to screw into the unit. b) Insert the three selected screws through each hole from the inside of the cabinet going down (see Figure 4). Warning: Please follow the steps below for proper mounting: 1. We recommend you install the 3 screws using hand tools. Do not use power tools because high torque can damage the threads on the main unit. 2. Please hold and support the unit before you insert any of the screws. 3. First mount 2 screws on opposite corners of the unit. c) Hold the unit up against the bottom of the cabinet, and align the three holes on the top of the unit with the screws. Partially tighten each screw, but do not fully tighten the screws until all of them have been started. d) Gently tighten each screw until they are firmly holding the unit in place. mounting Instructions EN - ES - FR - 4 If your cabinet doeS have an overhan…

Text truncated - open the document above for the full version.

          !" FM Antenna Bluetooth2402MHz to2480MHz HC180230A CMD2022B 5VDC R L MUTE Y20232.768kHz MC4863 Y226MHz X30232.768kHz

Date: 16 May, 2014

INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model : KLR33688B (External) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model : KLR33688B (External)

Model: KLR33688B Venturer Electronics Inc.Markham, Ontario L3R 1B8Made in China/Fabriqué en Chine/Fabricado en China Model: Letter size 2mm Letter size 2mm Brand name Letter size 5mm

INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal) INTERTEK TESTING SERVICE Report No.: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Equipment Photographs Model: KLR33688B (Internal)

Technical Description The Equipment Under Test (EUT) is a Kitchen Radio with Bluetooth audio feature. The Bluetooth portion is operating between 2402MHz and 2480MHz (79 channels with 1MHz channel spacing). When the EUT is switched ON in Bluetooth mode, the display will show “BT” and a LED flashing. The Bluetooth enabled device would be searched and connected the EUT before playing audio. After pairing, the “BT” LED will stay lit. The audio signal will be amplified and fed to internal stereo loudspeaker. The EUT also have FM radio and timer clock function. A LED display acts as the visual interface. The EUT is powered by 5V DC from an AC/DC adaptor. The AC/DC adaptor can accept 100-240VAC. 2.4GHz Bluetooth Module: Modulation Type: GFSK Antenna Type: Integral, Internal Frequency Range: 2402MHz - 2480MHz, 1MHz channel spacing, 79 channels Nominal field strength is 98.6dB μV/m @ 3m Production Tolerance of field strength is +/- 3dB Antenna gain is 0dBi The functions of main ICs are mentioned below. 1. BlueTooth module CMD2022B (BT1): 1) IC3 (CW6638M) acts as the 2.4GHz radio core of Bluetooth module 2) IC2 (AX2225) is MCU integrating with audio DSP and CODEC. 3) IC4 (24C08) is 8k serial EEPROM for parameter storage. 4) Y2 (26MHz) crystal provides system clock for IC3. 5) X302 (32.768kHz) crystal provides system clock for IC2. 2. AM/FM Radio Portion: 1) U3 (BK1080) acts as digital FM radio demodulator. 3. MCU module: 1) U2 (HC180230A) acts as MCU core for the product. 2) Y202 (32.768kHz) acts as clock for the MCU core (U2). 4. Audio portion: 1)U1(MC4863)is stereo 2W power amplifiers driving built-inloudspeakers. 5. Power Supply portion: 1) IC1 (JZ6206) is 3.3V voltage regulator. Channel Frequency Table of Bluetooth Module CMD2022B CW6638M Rev 1.0 Mar 2013 Bluetooth Module Table of Contents Chapter 1Description.............................................................................................................. 1 Chapter 2CMD2022B CW6638+AX2225A Features.............................................................. 1 Chapter 3Deminsion................................................................................................................ 2 Chapter 4Pin Assignment ..................................................................................................... 3 4.1 CMD2022B CW6638+AX2225A Pin Assignment ................................................................ 4 Chapter 5 Application.............................................................................................................. 4 Chapter 6Application Schematic .......................................................................................... 5 6.1 CMD2022B CW6638+AX2225A Application Schematic ..................................................... 5 Rev 1.0 CMD2022B -CW6638%OXHWRRWK0RGXOH 'HVFULSWLRQ CMD2022B-CW6638+AX2225A1 0 RGXOH'HVFULSWLRQ &:$;$LVUREXVW%OXHWRRWK$XGLR0RGXOHZKLFKKDVULFKIXQFWLRQVWDUJHWHG WRVPDOOVL]HSRUWDEOH$XGLR%RRPER[PDUNHW,QFRUSRUDWHGZLWK$SSRWHFKMP3GHFRGH IC CW6638+AX222ALVDKLJKO\FRPSHWLWLYHVROXWLRQCW6638MLV%OXHWRRWK2.1+EDR DQGDOVR%OXHWRRWK3.0FRPSDWLEOH  CMD2022B CW6638+AX222A0RGXOH3KRWRJUDSK CMD2022BCW66380RGXOH CMD2022 B-CW6638+AX2225A Module Characteristics xSupportU6%SD/TFFDUG xAux in with Volume Control˗˄WKUHH$8X_IN&KDQQHOV˅ x Support external FMUDGLRFKLS xSupport IR remote function˗ xSupport buzz tone˗ xSupportUSBFDUGUHDGHUIXQFWLRQˈDFFHVVSDTFDXGLRILOHV˗ xSupport power ON/OFF function˗ Rev 1.0 CMD2022BW6638%OXHWRWK0RGXOH ' HVFULSWLRQ CMD2022B-CW6638+AX2225A2 xSupport$8',2(Q8$/,=$7,21˗ xSupportUSB Host˗ xSupportL2CAP/A2DP(AVCTP/AVDTP/AVRCP) $XGLRILOHV xSupportMCUUART; 0 RGXOH'HPLQVLRQ 0RGXOH'HPDLQVLRQ CMD2022B CW6638 /×:×+=27.6mm × 15.6mm × 2mm Rev 1.0 CMD2022B -CW6638%OXHWRRWK0RGXOH 'HVFULSWLRQ CMD2022B-CW6638+AX2225A3 3 LQ$VVLJQPHQW CMD2022B-CW66383LQ$VVLJQPHQW 3LQ1DPH)XQFWLRQ'HVFULSWLRQ 1RF_ANTRF_ANT([WHUQDO$QWHQQD3RUW1&LILQWHUQDO3&%DQWHQQDLVXVHG; 23.3VPOWER3.3VRXWSXW 3PLAY/PAUSEDigital Input 3/$<3$86( 4BT_LEDDigital Input 3RZHU2Q,QGLFDWRU $FWLYH+LJK 5TEST1Digital I/O NC 6TEST2Digital I/O NC 7IIC_SDADigital I/O IICBSDA 8IIC_SCLDigital I/O IICBSCL 9NEXTDigital I/O 1H[W7UDFN 10PREVDigital I/O 3UHYLRXV7UDFN Rev 1.0 CMD2022BW6638%OXHWRRWK0RGXOH ' HVFULSWLRQ CMD2022B-CW6638+AX2225A4 11RTCPOWER5HDO7LPH&ORFN;(POWER) 1232KINDigital Input 32.768kHFORFN˗ 1332KOUTDigital out 32.768kHzFORFNRXWSXW 14GNDPOWER3RZHU*URXQG; 15USBDPDigital I/O USB'3 16USBDMDigital I/O USB'0 17BT_VDDPOWER0RGXOH3RZHU,QSXW 18SD_DATDigital I/O SD/TFGDWD; 19SD_CLKDigital I/O SD/TF&ORFN; 20SD_CMDDigital I/O SD/TF&0'; 21NCDigital I/O NC 22DACRDigital OUT '$&$XGLRRXW5; 23DACLDigital OUT '$&$XGLRRXW/; 24AGNDPOWER$QDORJ*URXQG; 25AUXR/P37Digital Input AUXR_input;RUM&8UART SURJUDPPDEOH ; 26AUXL/P36Digital Input $8;/BLQSXWRU0&88$57 SURJUDPPDEOH  27AUXR/P03Digital Input $8;5BLQSXWRU,2 SURJUDPPDEOH  28AUXL/P02Digital Input $8;/BLQSXWRU,2 SURJUDPPDEOH  29AUXR/P01Digital Input $8;5BLQSXWRU,2 SURJUDPPDEOH ; 30AUXL/P00Digital Input $8;/BLQSXWRU,2 SURJUDPPDEOH  31MUTE/P35Digital OUT MUTERU,2 SURJUDPPDEOH 32TESR3Digital I/O WHVWSRUW 1RWH0RGXOHIO is for 3.3V systemˈ'RQ WH[FHHG3.3V in application to avoid damage. $ SSOLFDWLRQ z Portable luetooth Audio zBluetooth MP3 Boombox zBluetooth Speaker zBluetooth Home Audio zHi-Fi Bluetooth Stereo Rev 1.0 CMD2022B -CW6638%OXHWRRWK0RGXOH 'HVFULSWLRQ CMD2022B-CW6638+AX2225A5 z Bluetooth Car Audio CMD2022B CW6638 Application Schematic MCU Schematic: .H\3DGDQG/('6FKHPDWLF: ˄а˅˖CMD2022BCW6638$SSOLFDWLRQ6FKHPDWLF Test Port C W 6 6 3 8 M Doc.NO:DS6638M Ver. 1.0 June/28/2012 Bluetooth 3.0 Single Chip for A2DP/AVRCP Solution CONWISE Technology Limited Tel: 886-3-5719960 8F, No.47, Lane 2, Kwang-Fu Rd. Sec. 2, Hsin-Chu City, Taiwan, 30071 Fax: 886-3-5719969 ˣ˴˺˸ˍʳ˄ʳ˂ʳ˄ˉ General Description The CONWISE CW6638M is a monolithic, s…

Text truncated - open the document above for the full version.

Analysis Report Report No.: 14090268HKG-002 The Equipment Under Test (EUT) is a Kitchen Radio with Bluetooth Audio feature. The Bluetooth portion is operating between 2402MHz and 2480MHz (79 channels with 1MHz channel spacing). When the EUT is switched ON in Bluetooth mode, the display will show “BT” and a LED flashing. The Bluetooth enabled device would be searched and connected the EUT before playing audio. After pairing, the “BT” LED will stay lit. The audio signal will be amplified and fed to internal stereo loudspeaker. The EUT also have FM radio and alarm clock function. A LED display acts as the visual interface. The EUT is powered by 5V DC from an AC/DC adaptor. The AC/DC adaptor can accept 100-240VAC. Antenna Type: Internal, Integral Antenna Gain: 0dBi Nominal rated field strength: 98.6dBμV/m at 3m Maximum allowed field strength of production tolerance: +/- 3dB According to the KDB 447498: Based on the Maximum allowed field strength of production tolerance was 101.6dBμV/m at 3m in frequency 2.4GHz, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 4.336mW Conducted power = Radiated Power (EIRP) – Antenna Gain So; Conducted Power = 4.336mW. The conducted source-based time-averaged output power = (4.336 *5/6 ) mW = 3.61 mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the above conducted source-based time-averaged output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: A2HSPS3688B

      !    !" 1uF 1uF0R 0R 104 BT1 NC 104 0RX3 10pX2 NC 32.768kHz Y202 HC180230A COM0 XIN 104 X2 10uH X4 104 X2 22R X4 10 2 X 4 L-INR-IN L-INR-IN VDD VDD GND 104 1K 1K 1 04 1 04 X2 0R X2 M UTE M UTE D C U1 1N4148 104 PNP 1K 1K I /O 0-12 S CLK S DIO M CLK VD D G ND R ST Bluetooth2402MHz to 2480MHz 2 6MHz 3 2.768kHz p air IC1 MC4863 FILE NAME : CMD2022BSHEET NAME :DRAWN BY : VERSION : V01 DATE : DATE : DATE : 105 475 475 475 475 1P IC2 IC424C08 475 L2 NC 0R NC 1.2NH IC5 SD_CMD(MODE)SD_CLK/(NEXT) SD_DAT(PREV) SPI_CLK/P05(VL+) SPI_DAT/P04(VOL-) SPI_CS/P23(P/P) RTC OSCO OSCI MD_RF IRDA/VPP/P07 2225-RX 2225-TX RTC SD_DAT(PREV) SD_CLK/(NEXT) SD_CMD(MODE) SPI_CS/P23(P/P) P33 AGND P13 SPI_DAT/P04(VOL-) SPI_CLK/P05(VL+) OSCO OSCI P13 P33 Bluetooth2402MHz to2480MHz CW6638M AX2225 IC2 IC3 CMD2022B Bluetooth Module Schematic X30232.768kHz
         !" 10K PNP 100R 10K

Issuing Laboratory: Intertek Testing Services Hong Kong Limited HKAS has accredited this laboratory (HOKLAS 005 – TEST) under HOKLAS for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. Report No.: 14090268HKG-002 i FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com GENERAL INFORMATION Grantee: Alco Electronics Ltd. Grantee Address: 11/F., Zung Fu Industrial Building, 1067 King’s Road, Quarry Bay, Hong Kong. Contact Person: Peggy Suen Tel: (852) 2562 6121 Fax: (852) 2597 5201 e-mail: [email protected] Manufacturer: Alco Electronics (Dongguan) Limited Manufacturer Address: Gong Ye Xi Road, Houjie Technology Industrial Park, Houjie, Dongguan, Guangdong P.R.C. 523960 China Brand Name: VENTURER / RCA Model: KLR33688B / SPS3688B Type of EUT: Transceiver Description of EUT: Kitchen Radio Serial Number: N/A FCC ID / IC: A2HSPS3688B / 9903A-SPS3688B Date of Sample Submitted: September 05, 2014 Date of Test: September 05, 2014 to September 16, 2014 Report No.: 14090268HKG-002 Report Date: September 24, 2014 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% Issuing Laboratory: Intertek Testing Services Hong Kong Limited HKAS has accredited this laboratory (HOKLAS 005 – TEST) under HOKLAS for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. Report No.: 14090268HKG-002 ii FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com SUMMARY OF TEST RESULT TEST SPECIFICATION REFERENCE RESULTS Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.4 Pass Radiated Emission Radiated Emission on the Bandedge 15.249 / RSS-210 A2.9 Pass Digital Device Radiated Emissions 15.109 / RSS-210 2.5 Pass Radiated Emission in Restricted Bands 15.205 / RSS-210 2.2 Pass The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2012 Edition RSS-210 Issue 8, December 2010 RSS-Gen Issue 3, December 2010 Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Issuing Laboratory: Intertek Testing Services Hong Kong Limited HKAS has accredited this laboratory (HOKLAS 005 – TEST) under HOKLAS for specific laboratory activities as listed in the HOKLAS directory of accredited laboratories. Report No.: 14090268HKG-002 iii FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com Table of Contents 1.0 General Description ....................................................................................... 1 1.1 Product Description ...................................................................................... 1 1.2 Related Submittal(s) Grants .......................................................................... 1 1.3 Test Methodology ......................................................................................... 2 1.4 Test Facility .................................................................................................. 2 2.0 System Test Configuration ............................................................................ 3 2.1 Justification................................................................................................... 3 2.2 EUT Exercising Software .............................................................................. 4 2.3 Special Accessories...................................................................................... 4 2.4 Measurement Uncertainty ............................................................................. 4 2.5 Support Equipment List and Description........................................................ 4 3.0 Emission Results ........................................................................................... 5 3.1 Field Strength Calculation ............................................................................. 5 3.2 Radiated Emission Configuration Photograph ............................................... 6 3.3 Radiated Emission Data ............................................................................... 6 3.4 Conducted Emission Configuration Photograph ............................................ 6 3.5 Conducted Emission Data............................................................................. 6 4.0 Equipment Photographs .............................................................................. 12 5.0 Product Labelling ......................................................................................... 12 6.0 Technical Specifications .............................................................................. 12 7.0 Instruction Manual ....................................................................................... 12 8.0 Miscellaneous Information .......................................................................... 13 8.1 Radiated Emission on the Bandedge .......................................................... 13 8.2 Discussion of Pulse Desensitization ............................................................ 15 8.3 Calculation of Average Factor .…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Configuration Photographs Worst-Case Radiated Emissions (Front View) Model: KLR33688B 14090268HKG-002 KLR33688B Side A INTERTEK TESTING SERVICE Report No: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Configuration Photographs Worst-Case Radiated Emissions (Rear View) Model: KLR33688B 14090268HKG-002 KLR33688B Side B

INTERTEK TESTING SERVICE Report No: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) Model: KLR33688B INTERTEK TESTING SERVICE Report No: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Configuration Photographs Worst-Case Line-Conducted Emissions (Rear View) Model: KLR33688B INTERTEK TESTING SERVICE Report No: 14090268HKG-002 FCC ID: A2HSPS3688B IC: 9903A-SPS3688B Configuration Photographs Worst-Case Line-Conducted Emissions (Side View) Model: KLR33688B