A4R-G1Bluetooth Accessory

Part 15 Warning Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-­‐located or operating in conjunction with any other antenna or transmitter. 15B Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -­‐ Reorient or relocate the receiving antenna. -­‐ Increase the separation between the equipment and receiver. -­‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -­‐ Consult the dealer or an experienced radio/TV technician for help. MPE or SAR Warning Statement FOR PORTABLE DEVICE USAGE (<20m from body/SAR needed) Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. 4000-00136-06 Copyright © 2014 All rights reserved. Let’s get started. 48.419 mm48.419 mm48.419 mm48.419 mm48.419 mm48.419 mm 290.512 mm 99.219 mm THE INFORMATION CONTAINED HEREIN IS DEEMED TO BE CONFIDENTIAL INFORMATION AND PROPERTY OF GOOGLE, INC. ("GOOGLE"). THIS INFORMATION MAY NOT BE USED, REPRODUCED, OR DISCLOSED BY THE RECIPIENT IN ANY MANNER, WHETHER FOR DEVELOPMENT, MANUFACTURE OR SALE OF PROCESSES OR PRODUCTS, WITHOUT THE EXPRESS PRIOR WRITTEN CONSENT OF GOOGLE. Product:Pa rt : Pa rt Numbe r: File Name:Ve rsion: Date:Op\Station: Process CyanProcess Magent a Process Ye llo w Process Black Stock: Stock Source:Size: Di e NotesFinishingGraphics “Molly Dev Bundle”Molly Dev QSG [Front]4000-00136-06193025_E8_4000-00136-06_Dev_Molly_Wlcm_QSG.inddAdobe InDesign CS605.02.14HWWoodfree paper ( uncoated ) equiv to approx 100# Text/150gsm Matte Aqueous Overall coating6-panel accordian fold N/A trim supplied per Google Printed: 290.512 mm x 99.219 mm, Finished: 48.419 mm x 9.219 mm Pantone 376 UPantone 424 U Let ’s get star ted . 193025_E8_4000-00136-06_Dev_Molly_Wlcm_QSG.indd 15/2/14 5:28 PM 1 2 34 For the latest information, visit: developer.android.com/tv THE INFORMATION CONTAINED HEREIN IS DEEMED TO BE CONFIDENTIAL INFORMATION AND PROPERTY OF GOOGLE, INC. ("GOOGLE"). THIS INFORMATION MAY NOT BE USED, REPRODUCED, OR DISCLOSED BY THE RECIPIENT IN ANY MANNER, WHETHER FOR DEVELOPMENT, MANUFACTURE OR SALE OF PROCESSES OR PRODUCTS, WITHOUT THE EXPRESS PRIOR WRITTEN CONSENT OF GOOGLE. Product:Pa rt : Pa rt Numbe r: File Name:Ve rsion: Date:Op\Station: Process CyanProcess Magent a Process Ye llo w Process Black Stock: Stock Source:Size: Di e NotesFinishingGraphics “Molly Dev Bundle”Molly Dev QSG [Back]4000-00136-06193025_E8_4000-00136-06_Dev_Molly_Wlcm_QSG.inddAdobe InDesign CS605.02.14HWWoodfree paper ( uncoated ) equiv to approx 100# Text/150gsm Matte Aqueous Overall coating6-panel accordian fold N/A trim supplied per Google Printed: 290.512 mm x 99.219 mm, Finished: 48.419 mm x 9.219 mm Pantone 376 UPantone 424 U 48.419 mm48.419 mm48.419 mm48.419 mm48.419 mm48.419 mm 290.512 mm 99.219 mm 193025_E8_4000-00136-06_Dev_Molly_Wlcm_QSG.indd 25/2/14 5:28 PM Safety Information + Power Adapter / Batteries For the latest information, visit: developer.android.com/tv Copyright © 2014 All rights reserved. 4000-00151-05 67.5 mm67.5 mm67.5 mm67.5 mm67.5 mm67.5 mm 405 mm 121.5 mm THE INFORMATION CONTAINED HEREIN IS DEEMED TO BE CONFIDENTIAL INFORMATION AND PROPERTY OF GOOGLE, INC. ("GOOGLE"). THIS INFORMATION MAY NOT BE USED, REPRODUCED, OR DISCLOSED BY THE RECIPIENT IN ANY MANNER, WHETHER FOR DEVELOPMENT, MANUFACTURE OR SALE OF PROCESSES OR PRODUCTS, WITHOUT THE EXPRESS PRIOR WRITTEN CONSENT OF GOOGLE. Product:Pa rt : Pa rt Numbe r: File Name:Ve rsion: Date:Op\Station: Process CyanProcess Magent a Process Ye llo w Stock: Stock Source:Size: Di e NotesFinishingGraphics “Molly Dev Bundle”Molly Dev Saftey Guide [Front]4000-00151-05193025_F5_4000-00151-05_Safety_Guide_Dev_Molly_Bundle.inddAdobe InDesign CS605.02.14HWLightweight offset woodfree/uncoated (bible paper) Matte Aqueous Varnish Change Request.docx (specs from Gordon Chan 2/3 10:39pm)email confirmation from Tim Guy on 4/01Printed: 405mm x 121.5mm, Finished: 67.5mm x 121.5mm Pantone 424 U Saf ety I nformation + Power A dapter / Batteries 193025_F5_4000-00151-05_Safety_Guide_Dev_Molly_Bundle.indd 15/2/14 6:08 PM Important Safety Instructions WARNING: Read all safety information below before using this device to avoid injury. · Do not install near heat sources, such as heaters and other devices. · Use in a well-ventilated area and plug power adapter into an easily accessible outlet. · Only use this device with the provided power adapter. · The device has no on/off switch. To disconnect from power, you must unplug the power adapter. · Only use indoors and do not exp…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

5 5 18 Popo Zhu Apr. 24mm 33mm Odi Design ChangeStickerNote 1: Eliminate recessed perimeter around contact pin through-hole.Note 2: New debossed footprint for sticker meant to conceal contact pin through-hole.Google Android 2014 / Confidential and Proprietary

Page 2 Page 3 Page 4 Page 5 Page 6 Page 7

Report No.: SA140401C08 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140401C08 MODEL NO.: G1 FCC ID: A4R-G1 RECEIVED: Apr. 01, 2014 TESTED: Apr. 01 ~ Apr. 02, 2014 ISSUED: Apr. 07, 2014 APPLICANT: Google Inc. ADDRESS: 1600 Amphitheatre Parkway, Mountain View, CA 94043, United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140401C08 2 of 6 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA140401C08 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140401C08 Original release. Apr. 07, 2014 Report No.: SA140401C08 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION MODEL NO.:G1 BRAND:Google Inc. APPLICANT:Google Inc. TESTED:Apr. 01 ~ Apr. 02, 2014 TEST SAMPLE:ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: G1) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Apr. 07, 2014 Suntee Liu / Specialist APPROVED BY: , DATE :Apr. 07, 2014 Ken Liu / Senior Manager Report No.: SA140401C08 5 of 6 Report Format Version 5.0.0 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [(Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [(Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140401C08 6 of 6 Report Format Version 5.0.0 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g SAR test exclusion thresholds Result 2.402 ~ 2.480 0.643 5 0.199 3 Pass NOTE: 1. The antenna type is PIFA antenna with 2.36dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, t…

Text truncated - open the document above for the full version.

Report No.: RF140401C08 1 of 35 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF140401C08 MODEL NO.: G1 FCC ID: A4R-G1 RECEIVED: Apr. 01, 2014 TESTED: Apr. 01 ~ Apr. 02, 2014 ISSUED: Apr. 07, 2014 APPLICANT: Google Inc. ADDRESS: 1600 Amphitheatre Parkway, Mountain View, CA 94043, United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140401C08 2 of 35 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 4 1. CERTIFICATION ........................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................. 6 3. GENERAL INFORMATION ......................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................. 9 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................... 12 4. TEST TYPES AND RESULTS .................................................................................. 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................. 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................ 13 4.1.2 TEST INSTRUMENTS ............................................................................................. 14 4.1.3 TEST PROCEDURES .............................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD .................................................................... 15 4.1.5 TEST SETUP ........................................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ............................................................................. 16 4.1.7 TEST RESULTS ....................................................................................................... 17 4.2 NUMBER OF HOPPING FREQUENCY USED ........................................................ 21 4.2.1 LIMIT OF HOPPING FREQUENCY USED .............................................................. 21 4.2.2 TEST SETUP ........................................................................................................... 21 4.2.3 TEST INSTRUMENTS ............................................................................................. 21 4.2.4 TEST PROCEDURES .............................................................................................. 21 4.2.5 DEVIATION FROM TEST STANDARD .................................................................... 21 4.2.6 TEST RESULTS ....................................................................................................... 21 4.3 DWELL TIME ON EACH CHANNEL ........................................................................ 23 4.3.1 LIMIT OF DWELL TIME USED ................................................................................. 23 4.3.2 TEST SETUP ........................................................................................................... 23 4.3.3 TEST INSTRUMENTS ............................................................................................. 23 4.3.4 TEST PROCEDURES .............................................................................................. 23 4.3.5 DEVIATION FROM TEST STANDARD .................................................................... 23 4.3.6 TEST RESULTS ....................................................................................................... 24 4.4 CHANNEL BANDWIDTH .......................................................................................... 25 4.4.1 LIMITS OF CHANN…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST