A4RG9N9NWireless Device

Safety, Warranty & Regulatory Guide This booklet provides important safety, regulatory, and warranty information that you should read before using your device. You can find an online version of this document at ​XXXX Basic safety WARNING: HEALTH AND SAFETY INFORMATION, READ BEFORE USE To avoid damaging your device, accessories, or any connected devices and to reduce the risk of personal injury, discomfort, property damage or other potential hazards, follow the precautions below and those found in the device Safety Information at ​XXXXX​: ●Handle your device with care. You may damage the device if you disassemble, drop, bend, burn, crush or puncture them. Be sure the power adapter and device are well ventilated when in use. Using a damaged device ​damaged cables or power adapter, or using when moisture or debris is present,​ may cause overheating, ​fire, electric shock, injury or damage to your device or other ​property​. Do not expose your device to liquids, which can cause a short circuit and overheating. Do not power the device when wet or in direct sunlight. ●Only power this device with the included power adapter and cable or compatible accessories available on the Google Store or at Google authorized resellers (look for Google’s “made for” badge). Failure to use compatible accessories can cause fire, electric shock, injury, or damage to the device and the accessories. ●Strangulation hazard. This device is not a toy. Children have strangled on cords. Keep the cords out of the reach of children (more than 3 feet / 1 meter away). Disposal & Recycling Dispose of your device, batteries and accessories according to local environmental regulations. Do not dispose of them in normal household waste. ​ ​For more information on recycling your device, batteries and accessories, visit XXXXX Service & Support [US Version & ROW Version] For online help and support, visit XXXXX. If you send your device in for service, you might receive a replacement. Repair or replacement may result in the loss of user-generated data. 1 DRAFT Regulatory information RADIO FREQUENCY EXPOSURE This device has been evaluated and meets the applicable regulatory requirements for radio frequency (RF) exposure​. Manufacturer address: Google LLC, 1600 Amphitheatre Parkway, Mountain View, CA 94043. [USE FOR UNITED STATES & CANADA] FCC & ISED CANADA REGULATORY COMPLIANCE U.S. contact information: Google LLC, 1600 Amphitheatre Parkway, Mountain View, CA 94043 Contact: XXXXX Model number: G9N9N Product name: Google Wireless Device Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver. ●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ●Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Google could void your authority to operate the equipment. 2 DRAFT This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions: 1. These devices may not cause harmful interference. 2. These devices must accept any interference received, including interference that may cause undesired operation. Industry Canada, Class B This Class B digital apparatus complies with ​CAN ICES-3(B)/NMB-3(B) Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Notice: The Industry Canada regulations provide that changes or modifications not expressly approved by Google could void your authority to operate this equipment. This device complies with ​ISED ​license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Specific Absorption Rate (SAR) Information The radiated output power of this device is below the Industry Canada (IC) radio frequency exposure limits. These devices have been evaluated for and shown compliant with the IC Radio Frequency (RF) Exposure limits. These devices should be used in a manner such that the potential for human contact during normal operation is minimized. This device has been certified for use in Canada. Status of the listing in the ISED’s (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do Additional Canadian information on RF exposure also can be found at the following web address: ​http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html EMC Compliance Statement Important: This device [and its power adapter] have demonstrated Electromagnetic Compatibility (EMC) compliance under conditions that included the use of compliant peripheral 3 DRAFT devices and shielded cables between system components. It is import…

Text truncated - open the document above for the full version.

Let’s get started 1.Plug in Chromecast Plug your Chomecast into a power outlet and an HDMI port on yout TV 2.Switch TV Input Turn on your TV and switch to the input/source your Chromecast is plugged into 3.Put batteries in your voice remote You will find batteries in the box 4.Get the Google Home App

1600 Amphitheatre Parkway Mountain View, CA 94043 USA April 29, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: A4RG9N9N To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 C.F.R. §§ 0.457, 0.459), we request that the Commission withhold the following attachments as confidential documents from public disclosure indefinitely. ●Schematic Diagram ●Block Diagram ●Theory of Operation (Operational and Technical Descriptions) ●Antenna Pattern In support of this request, we provide the following information: 1.Identification of the specific information for which confidential treatment is sought (§ 0.459(b)(1)): We request that all of the information contained in the above-referenced exhibits to the certification application be withheld from routine public disclosure. 2.Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission (§ 0.459(b)(2)): The material is being submitted in connection with our certification application for the above-captioned FCC ID . 3.Explanation of the degree to which the information is commercial, or financial or contains a trade secret or is privileged (§ 0.459(b)(3)): The market for the technology that is the subject of the certification application is highly competitive, with numerous companies competing for the business of potential customers. Were competitors to become aware of the facts set forth in the above-referenced exhibits to the application at this time, it could have an adverse impact on our competitive standing and deprive us of the marketplace benefit we otherwise might achieve by virtue of having the product available before other competitors. If any of the information for which confidential treatment is sought was made publicly available, competitors could reasonably determine the scope and status of our activities. 4.Explanation of the degree to which the information concerns a service that is competitive (§ 0.459(b)(4)): The technology that is the subject of the certification application is subject to intense competition from other manufacturers and service providers that are developing competing services and technology. 1 5.Explanation of how disclosure of the information could result in substantial competitive harm (§ 0.459(b)(5)): As noted above, were our competitors to become aware of the facts set forth in the above-referenced exhibits to the application, it could have an adverse impact on our competitive standing and deprive us of the marketplace benefit we otherwise would achieve by virtue of having the product available before other providers. 6.Identification of any measures taken by the requesting party to prevent unauthorized disclosure (§ 0.459(b)(6)): The information contained in the above-referenced exhibits to the certification application has been strictly controlled by us, with distribution limited to internal use only and for the specific purpose of conducting research, development, and testing of the technology. 7.Identification of whether the information is available to the public and the extent of any previous disclosures of the information to any third parties (§ 0.459(b)(7)): The information that we request be maintained as confidential is not available publicly. The information has been protected and kept confidential by limiting external contacts to privileged and confidential communications. 8.Justification of the period during which the submitting party asserts that material should not be available for public disclosure (§ 0.459(b)(8)): Given the competitive nature of the marketplace, any disclosure that we have developed the technology discussed in the above-referenced exhibits to the certification application would harm our competitive position. The information subject to this request for confidentiality should not be made available for public disclosure at any time. In addition, pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. §2.803 and the importation rules in 47 C.F.R. §2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we also request that the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until (180) days after the grant date. ●External Photos ●Internal Photos ●Test Setup Photos ●User Manual It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely yours, John McNulty Head of Safety and Compliance Engineering Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 T: 650-203-0646 E: [email protected] 2

1600 Amphitheatre Parkway Mountain View, CA 94043 USA Date: April 29, 2020 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: A4RG9N9N To Whom It May Concern: I, the undersigned, hereby authorize Sporton International Inc. (Sporton) to act on Google LLC’s (Google) behalf in all manners relating to the above-captioned application for equipment authorization, including signing of all documents relating to this matter. Any and all acts carried out by Sporton on Google’s behalf shall have the same effect as acts of Google’s own. I, the undersigned, hereby certify that Google is not subject to a denial of federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 853(a). In authorizing Sporton as Google’s representative, Google recognizes that it is still responsible for: a) complying with the relevant provisions of the certification program; b)making all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)making claims regarding certification only in respect of the scope for which certification has been granted; d)not using the product certification in such a manner as to bring Sporton into disrepute and not making any statement regarding the product certification that Sporton may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinuing the use of all advertising matter that contains any reference thereto and return any certification documents as required by Sporton; f) using the certification only to indicate that the products are certified as being in conformity with specified standards; g) endeavoring to ensure that no certificate or report or any part thereof is used in a misleading manner; h)ensuring that any reference to the product certification in communication media such as documents, brochures, or advertising, complies with Sporton’s requirements; i)keeping a record of all complaints made known to Google relating to the product’s compliance with the requirements of the relevant standard and making these records available to the applicable authorities when requested; j)taking appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; and k)documenting the actions taken. This authorization is valid until further written notice from Google. Sincerely Yours, John McNulty Head of Safety and Compliance Engineering Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 T: 650-203-0646 E: [email protected] 2

PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 1 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 External Photograph of EUT PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 2 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 3 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 4 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 5 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 6 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 ─────THE END──── 720510

Label Artwork: Location: under the power cover on a location that is user non-removable FCC ID: A4RG9N9N IC ID: 10395A-G9N9N

PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 1 of 2 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 Internal Photograph of EUT PHOTOGRAPHS OF EUT Report No.: EP971034-05 Model Name: G9N9N TEL : 886-3-327-3456 Page Number : 2 of 2 FAX : 886-3-328-4978 Issued Date : Jun. 05, 2020 Report Version : 01 ─────THE END──── 720510

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2020/6/1 System Check_Head_2450MHz DUT: D2450V2-929 Communication System: CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL_2450_200601 Medium parameters used: f = 2450 MHz; σ = 1.79 S/m; ε r = 39.004; ρ = 1000 3 kg/m Ambient Temperature：23.4 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: ES3DV3 - SN3184; ConvF(4.69, 4.69, 4.69) @ 2450 MHz; Calibrated: 2019/9/25 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE4 Sn916; Calibrated: 2019/12/17 - Phantom: SAM_Right; Type: QD000P40CD; Serial: TP:1683 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (71x71x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 17.6 W/kg Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 94.81 V/m; Power Drift = -0.08 dB Peak SAR (extrapolated) = 21.4 W/kg SAR(1 g) = 12.5 W/kg; SAR(10 g) = 6.15 W/kg Maximum value of SAR (measured) = 16.2 W/kg 0 dB = 16.2 W/kg = 12.10 dBW/kg

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2020/6/1 #01_Bluetooth_1Mbps_Front_0mm_Ch0 Communication System: Bluetooth; Frequency: 2402 MHz;Duty Cycle: 1:1 Medium: HSL_2450_200601 Medium parameters used: f = 2402 MHz; σ = 1.737 S/m; ε r = 39.132; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: ES3DV3 - SN3184; ConvF(4.69, 4.69, 4.69) @ 2402 MHz; Calibrated: 2019/9/25 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE4 Sn916; Calibrated: 2019/12/17 - Phantom: SAM_Right; Type: QD000P40CD; Serial: TP:1683 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7483) Area Scan (71x111x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.526 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 13.64 V/m; Power Drift = -0.14 dB Peak SAR (extrapolated) = 0.823 W/kg SAR(1 g) = 0.407 W/kg; SAR(10 g) = 0.181 W/kg Maximum value of SAR (measured) = 0.528 W/kg 0 dB = 0.528 W/kg = -2.77 dBW/kg

Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland Accredited by the Swiss Accreditation Service (SAS) The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates s Schweizerischer Kalibrierdienst C Service suisse d'etalonnage Servizio svizzero di taratura s Swiss Calibration Service Accreditation No.: SCS 0108 Client Sporton Certificate No: 02450V2-929 _Nov19 CALIBRATION CERTIFICATE Object D2450V2 - SN:929 Calibration procedure(s) QA CAL-05.v11 Calibration Procedure for SAR Validation Sources between 0.7-3 GHz Calibration date: November 21, 2019 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (SI). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 ± 3)°C and humidity< 70%. Calibration Equipment used (M& TE critical for calibration) Primary Standards ID# Power meter NRP SN: 104778 Power sensor NRP-Z91 SN: 103244 Power sensor NRP-Z91 SN: 103245 Reference 20 dB Attenuator SN: 5058 (20k) Type-N mismatch combination SN: 5047.2 / 06327 Reference Probe EX3DV4 SN: 7349 DAE4 SN: 601 Secondary Standards ID # Power meter E4419B SN: 8839512475 Power sensor HP 8481A SN: US37292783 Power sensor HP 8481A SN: MY41092317 RF generator R&S SMT-06 SN: 100972 Network Analyzer Agilent E8358A SN: US41080477 Name Calibrated by: Claudio Leubler Approved by: Katja Pokovic Cal Date (Certificate No.) 03-Apr-19 (No. 217-02892/02893) 03-Apr-19 (No. 217-02892) 03-Apr-19 (No. 217-02893) 04-Apr-19 (No. 217-02894) 04-Apr-19 (No. 217-02895) 29-May-19 (No. EX3-7349_May19) 30-Apr-19 (No. DAE4-601_Apr19) Check Date (in house) 30-0ct-14 (in house check Feb-19) 07-0ct-15 (in house check Oct-18) 07-0ct-15 (in house check Oct-18) 15-Jun-15 (in house check Oct-18) 31-Mar-14 (in house check Oct-19) Function Laboratory Technician Technical Manager This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2450V2-929_Nov19 Page 1 of 7 Scheduled Calibration Apr-20 Apr-20 Apr-20 Apr-20 Apr-20 May-20 Apr-20 Scheduled Check In house check: Oct-20 In house check: Oct-20 In house check: Oct-20 In house check: Oct-20 In house check: Oct-20 Issued: November 25, 2019 Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland Accredited by the Swiss Accreditation Service (SAS} The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL ConvF N/A tissue simulating liquid sensitivity in TSL / NORM x,y,z not applicable or not measured Calibration is Performed According to the Following Standards: S Schweizerischer Kalibrierdienst C s Service suisse d'etalonnage Servizio svizzero di taratura Swiss Calibration Service Accreditation No.: SCS 0108 a) IEEE Std 1528-2013, "IEEE Recommended Practice for Determining the Peak Spatial- Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209-1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand-held and body-mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209-2, 11 Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) 11 , March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY 4/5 System Handbook Methods Applied and Interpretation of Parameters: • Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. • Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. • Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. • Electrical Delay: One-way delay between the SMA connector and the antenna feed point. No uncertainty required. • SAR measured: SAR measured at the stated antenna input power. • SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. • SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: 02450V2-929_Nov19 Page 2 of 7 Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.3 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center -TSL 10mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 2450 MHz ± 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 ± 0.2) 0 c 38.2 ± 6 % 1 .84 mho/m ± 6 % Head TSL temperature change during test < 0.5 °C ---- ---- SAR result with Head TSL SAR averaged over 1 cm 3 (1 g) of Head TSL Condition SAR measured 250 mW input power 13.5 W/kg SAR for nominal He…

Text truncated - open the document above for the full version.

TEL : 886-3-327-3456 Page 1 of 20 FAX : 886-3-328-4978 Issued Date : Aug. 03, 2020 Template version: 200217 FCC SAR TEST REPORT Report No. : FA971034-05 FCC SAR TEST REPORT FCC ID : A4RG9N9N Equipment : Wireless Device Model Name : G9N9N Applicant : Google LLC 1600 Amphitheatre Parkway, Mountain View, California, 94043 USA Standard : FCC 47 CFR Part 2 (2.1093) ANSI/IEEE C95.1-1992 IEEE 1528-2013 The product was received on Jun. 01, 2020 and testing was on Jun. 01, 2020. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any agency of government. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page 2 of 20 FAX : 886-3-328-4978 Issued Date : Aug. 03, 2020 Template version: 200217 FCC SAR TEST REPORT Report No. : FA971034-05 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Guidance Applied .......................................................................................................................................................... 4 3. Equipment Under Test (EUT) Information ................................................................................................................... 4 3.1 General Information ............................................................................................................................................... 4 4. RF Exposure Limits....................................................................................................................................................... 5 4.1 Uncontrolled Environment ...................................................................................................................................... 5 4.2 Controlled Environment .......................................................................................................................................... 5 5. Specific Absorption Rate (SAR) ................................................................................................................................... 6 5.1 Introduction ............................................................................................................................................................ 6 5.2 SAR Definition ........................................................................................................................................................ 6 6. System Description and Setup .................................................................................................................................... 7 6.1 E-Field Probe ......................................................................................................................................................... 8 6.2 Data Acquisition Electronics (DAE) ........................................................................................................................ 8 6.3 Phantom ................................................................................................................................................................. 9 6.4 Device Holder........................................................................................................................................................10 7. Measurement Procedures ...........................................................................................................................................11 7.1 Spatial Peak SAR Evaluation ................................................................................................................................ 11 7.2 Power Reference Measurement............................................................................................................................12 7.3 Area Scan .............................................................................................................................................................12 7.4 Zoom Scan ............................................................................................................................................................13 7.5 Volume Scan Procedures ......................................................................................................................................13 7.6 Power Drift Monitoring ...........................................................................................................................................13 8. Test Equipment List .....................................................................................................................................................14 9. System Verification ......................................................................................................................................................15 9.1 Tissue Simulating Liquids ......................................................................................................................................15 9.2 Tissue Verification .................................................................................................................................................16 9.3 System Performance Check Results .....................................................................................................................17 10. Bluetooth Output Power (Unit:…

Text truncated - open the document above for the full version.

TEL : 886-3…

Text truncated - open the document above for the full version.