A4RGLU0GPhone

Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 650 253-0000 main Google.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 November 12, 2022 Subject:KDB 987594 D01 U-NII 6GHz General Requirements To Whom It May Concern: We, Google LLC, attest the following for our device FCC ID: A4RGLU0G . a. This device does not support 6PP (subordinate device). b. This device will only associate and connect with a low-power indoor Access Point, subordinate device, or standard access point and never directly link to any other client devices c. This device will always initiate transmission under the control of a low power indoor AP or subordinate or standard client except access point for brief communications before joining a network. These quick messages will only occur if the 987594 D01 U-NII 6GHz General Requirements v01r02 20 client has detected an indoor AP, subordinate, or standard access point operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. d. This device, when associated and connected with a low-power indoor access point, subordinate or standard access point device, will operate at a power lower as advertised by the indoor access point, subordinate, or standard access point: i. Lower than or equal to the power advertised by the low-power indoor access point or subordinate and never above the maximum output power allowed by the FCC grant for clients associated with indoor clients or subordinates. ii. Lower than or 6 dB below the power advertised by the standard access point. e. We acknowledge the device is prohibited for control of or communications with unmanned aircraft systems, including drones. Sincerely yours, ___________________________ Clarence Ip Regulatory Compliance Program Manager Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043

GoogleLLC 1600AmphitheatreParkway MountainView,CA94043 650253-0000main Google.com FederalCommunicationsCommission 7435OaklandMillsRoad ColumbiaMD21046 February22,2023 Subject:Certificationsconcerning“covered”equipmentpursuanttoPart2.911(d)(5)(i)and(ii) FCCID:A4RGLU0G Towhomitmayconcern, GoogleLLC(“theapplicant”)certifiesthattheequipmentforwhichauthorizationissoughtisnot “covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuanttosection2.903 oftheFCCrules.Theapplicantalsocertifiesthat,asofthedateofthefilingoftheapplication,the applicantisnotidentifiedontheCoveredListasanentityproducing“covered”equipment,andis notanaffiliateorsubsidiaryofanentityidentifiedontheCoveredList. Sincerelyyours, ______________________________ ClarenceIp RegulatoryComplianceProgramManager GoogleLLC 1600AmphitheatreParkway MountainView,CA94043USA

Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 650 253-0000 main Google.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 February 22, 2023 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) FCC ID: A4RGLU0G FRN: 0020499539 To whom it may concern, Google LLC (“the applicant”) designates itself as the agent for service of process. Hereby we acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process; also acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Sincerely yours, ______________________________ Clarence Ip Regulatory Compliance Program Manager Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 USA Email: [email protected]

Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 650 253-0000 main Google.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 November 12, 2022 Subject:Request for Confidentiality FCC ID:A4RGLU0G To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 C.F.R. §§ 0.457, 0.459), we request that the Commission withhold the following attachments as confidential documents from public disclosure indefinitely. ● Schematic Diagram ● Block Diagram ● Theory of Operation (Operational and Technical Descriptions) ● Tune Up Procedure In support of this request, we provide the following information: 1.Identificationofthespecificinformationforwhichconfidentialtreatmentissought(§0.459(b)(1)):We requestthatalloftheinformationcontainedintheabove-referencedexhibitstothecertificationapplicationbe withheld from routine public disclosure. 2.IdentificationoftheCommissionproceedinginwhichtheinformationwassubmittedoradescriptionofthe circumstancesgivingrisetothesubmission(§0.459(b)(2)):Thematerialisbeingsubmittedinconnectionwith our certification application for the above-captioned FCC ID. 3.Explanationofthedegreetowhichtheinformationiscommercial,orfinancialorcontainsatradesecretor isprivileged(§0.459(b)(3)):Themarketforthetechnologythatisthesubjectofthecertificationapplicationis highlycompetitive,withnumerouscompaniescompetingforthebusinessofpotentialcustomers.Were competitorstobecomeawareofthefactssetforthintheabove-referencedexhibitstotheapplicationatthistime, itcouldhaveanadverseimpactonourcompetitivestandinganddepriveusofthemarketplacebenefitwe otherwisemightachievebyvirtueofhavingtheproductavailablebeforeothercompetitors.Ifanyofthe informationforwhichconfidentialtreatmentissoughtwasmadepubliclyavailable,competitorscouldreasonably determine the scope and status of our activities. 4.Explanationofthedegreetowhichtheinformationconcernsaservicethatiscompetitive(§0.459(b)(4)): Thetechnologythatisthesubjectofthecertificationapplicationissubjecttointensecompetitionfromother manufacturers and service providers that are developing competing services and technology. 5.Explanationofhowdisclosureoftheinformationcouldresultinsubstantialcompetitiveharm(§ 0.459(b)(5)):Asnotedabove,wereourcompetitorstobecomeawareofthefactssetforthinthe above-referencedexhibitstotheapplication,itcouldhaveanadverseimpactonourcompetitivestandingand depriveusofthemarketplacebenefitweotherwisewouldachievebyvirtueofhavingtheproductavailablebefore other providers. 6.Identificationofanymeasurestakenbytherequestingpartytopreventunauthorizeddisclosure(§ 0.459(b)(6)):Theinformationcontainedintheabove-referencedexhibitstothecertificationapplicationhasbeen strictlycontrolledbyus,withdistributionlimitedtointernaluseonlyandforthespecificpurposeofconducting research, development, and testing of the technology. 7.Identificationofwhethertheinformationisavailabletothepublicandtheextentofanyprevious disclosuresoftheinformationtoanythirdparties(§0.459(b)(7)):Theinformationthatwerequestbe maintainedasconfidentialisnotavailablepublicly.Theinformationhasbeenprotectedandkeptconfidentialby limiting external contacts to privileged and confidential communications. 8.Justificationoftheperiodduringwhichthesubmittingpartyassertsthatmaterialshouldnotbeavailable forpublicdisclosure(§0.459(b)(8)):Giventhecompetitivenatureofthemarketplace,anydisclosurethatwe havedevelopedthetechnologydiscussedintheabove-referencedexhibitstothecertificationapplicationwould harmourcompetitiveposition.Theinformationsubjecttothisrequestforconfidentialityshouldnotbemade available for public disclosure at any time. In addition, pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. §2.803 and the importation rules in 47 C.F.R. §2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we also request that the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until 180days after the grant date. ● External Photos ● Internal Photos ● Test Setup Photos ● User Manual It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely yours, ___________________________ Clarence Ip Regulatory Compliance Program Manager Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 2

Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 650 253-0000 main Google.com Date: November 12, 2022 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: A4RGLU0G To Whom It May Concern: I, the undersigned, hereby authorize Sporton International Inc. (Sporton) to act on Google LLC’s (Google) behalf in all manners relating to the above-captioned application for equipment authorization, including signing of all documents relating to this matter. Any and all acts carried out by Sporton on Google’s behalf shall have the same effect as acts of Google’s own. I,theundersigned,herebycertifythatGoogleisnotsubjecttoadenialoffederalbenefits, includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuseActof1988,21 U.S.C.§853(a). InauthorizingSportonasGoogle’srepresentative,Googlerecognizesthatitisstillresponsible for: a)complying with the relevant provisions of the certification program; b)making all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)making claims regarding certification only in respect of the scope for which certification has been granted; d)not using the product certification in such a manner as to bring Sporton into disrepute and not making any statement regarding the product certification that Sporton may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinuing the use of all advertising matter that contains any reference thereto and returning any certification documents as required by Sporton; f)using the certification only to indicate that the products are certified as being in conformity with specified standards; g)endeavoring to ensure that no certificate or report or any part thereof is used in a misleading manner; h)ensuring that any reference to the product certification in communication media such as documents, brochures, or advertising, complies with Sporton’s requirements; i)keeping a record of all complaints made known to Google relating to the product’s compliance with the requirements of the relevant standard and making these records available to the applicable authorities when requested; j)taking appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; and k)documenting the actions taken. This authorization is valid until further written notice from Google. Sincerely yours, ___________________________ Clarence Ip Regulatory Compliance Program Manager Google LLC 1600 Amphitheatre Parkway Mountain View, CA 94043 2

E-label Declaration FCC ID: A4RGLU0G FCC §2.935 Electronic labeling of radiofrequency devices. (a) Any radiofrequency device equipped with an integratedelectronic display screen, or a radiofrequency device without an integrated screenthat can only operate in conjunction with a device that has an electronic display screen,may display on the electronic display the FCC Identifier, any warning statements, or otherinformation that the Commission’s rules would otherwise require to be shown on a physicallabel attached to the device. InformationOn e-labelIn Manual FCC ID numberYesNo 15.19 Statement(“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.”) NoYes Class B Digital Device user manual statementNoYes Caution to the user that changes or modificationsnot expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment NoYes Image of the e-label screen is provided below: (b) Devices displaying their FCC Identifier, warningstatements, or other information electronically must make this information readilyaccessible on the electronic display. Users must be provided with prominent instructionson how to access the information in the operating instructions, inserts in packaging material,or other easily accessible format at the time of purchase. The access instructions mayalso be provided via the product-related website, if such a web site exists;the packaging material must provide specific instructions on how to locate the websiteinformation, and a copy of these instructions must be included in the application forequipment certification. The instruction on how to access the information is in the box in the Safety/Warranty/Regulatory booklet, and in the onlineversion of the Safety/Warranty/Regulatory booklet: “ Regulatory information, certification, and compliancemarks can be found with the following steps from the Home screen:Settings > Aboutphone > Regulatory labels.” (c) Devices displaying their FCC Identifier, warningstatements, or other information electronically must permit access to the informationwithout requiring special codes, accessories or permissions and the access to thisinformation must not require more than three steps from the device setting menu. The numberof steps does not include those steps for use of screen locks, passcodes or similarsecurity protection designed to control overall device access. No special accessories or supplemental plug-ins arerequired to access the information. To access the e-label information, in the device fromthe Home screen: Select: Settings > About phone > Regulatory labels (d) The electronically displayed FCC Identifier, warningstatements, or other information must be displayed electronically in a manner thatis clearly legible without the aid of magnification; Yes (e) The necessary label information must be programmedby the responsible party and must be secured in such a manner that third-partiescannot modify it. The e-label information is pre-programmed by the grantee.The user cannot modify the e-label information. (f) Devices displaying their FCC Identifier, warningstatements, or other information electronically must also be labeled, either on thedevice or its packaging, with the FCC Identifier or other information (such as a model numberand identification of a webpage that hosts the relevant regulatory information) thatpermits the devices to be identified at the time of importation, marketing, and sales as complyingwith the FCC’s equipment authorization requirements. Devices can be labeledwith a stick-on label, printing on the packaging, a label on a protective bag, or by similarmeans. Any removable label shall be of a type intended to survive normal shipping andhandling and must only be removed by the customer after purchase. The FCC ID is present on the product packaging.

Internal Photos

TEL : 886-3-327-3456 Page : 1 of 16 FAX : 886-3-328-4978 Issued Date : Nov. 29, 2022 Form version: 180516 FCC RF EXPOSURE REPORT Report No. : FA121931-25A RF Exposure Evaluation (Mobile Condition) FCC ID : A4RGLU0G Equipment : Phone Applicant : Google LLC 1600 Amphitheatre Parkway, Mountain View, California, 94043 USA Standard : 47 CFR Part 2.1091 We, SPORTON INTERNATIONAL INC has been evaluated in accordance with 47 CFR Part 2.1091 for the device and pass the limit. The results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page : 2 of 16 FAX : 886-3-328-4978 Issued Date : Nov. 29, 2022 Form version: 180516 FCC RF EXPOSURE REPORT Report No. : FA121931-25A Table of Contents 1. DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ............................................................................. 4 2. MAXIMUM TUNE-UP LIMIT (UNIT: DBM) .................................................................................................. 5 3. RF EXPOSURE LIMIT INTRODUCTION .................................................................................................. 14 4. RADIO FREQUENCY RADIATION EXPOSURE EVALUATION ............................................................. 15 4.1. Power Density Calculation ............................................................................................................... 15 TEL : 886-3-327-3456 Page : 3 of 16 FAX : 886-3-328-4978 Issued Date : Nov. 29, 2022 Form version: 180516 FCC RF EXPOSURE REPORT Report No. : FA121931-25A History of this test report Report No. Version Description Issued Date FA121931-25A Rev. 01 Initial issue of report Nov. 29, 2022 TEL : 886-3-327-3456 Page : 4 of 16 FAX : 886-3-328-4978 Issued Date : Nov. 29, 2022 Form version: 180516 FCC RF EXPOSURE REPORT Report No. : FA121931-25A 1. Description of Equipment Under Test (EUT) Product Feature & Specification Equipment Name Phone FCC ID A4RGLU0G Wireless Technology and Frequency Range GSM850: 824.2 MHz ~ 848.8 MHz GSM1900: 1850.2 MHz ~ 1909.8 MHz WCDMA Band II: 1850 MHz ~ 1910 MHz WCDMA Band IV: 1710 MHz ~ 1755 MHz WCDMA Band V: 824 MHz ~ 849 MHz LTE Band 2: 1850 MHz ~ 1910 MHz LTE Band 4: 1710 MHz ~ 1755 MHz LTE Band 5: 824 MHz ~ 849 MHz LTE Band 7: 2500 MHz ~ 2570 MHz LTE Band 12: 699 MHz ~ 716 MHz LTE Band 13: 777 MHz ~ 787 MHz LTE Band 14: 788 MHz ~ 798 MHz LTE Band 17: 704 MHz ~ 716 MHz LTE Band 25: 1850 MHz ~ 1915 MHz LTE Band 26: 814 MHz ~ 849 MHz LTE Band 30: 2305 MHz ~ 2315 MHz LTE Band 38: 2570 MHz ~ 2620 MHz LTE Band 41: 2496 MHz ~ 2690 MHz LTE Band 48: 3550 MHz ~ 3700 MHz LTE Band 66: 1710 MHz ~ 1780 MHz LTE Band 71: 663 MHz ~ 698 MHz 5G NR n2 : 1850 MHz ~ 1910 MHz 5G NR n5 : 824 MHz ~ 849 MHz 5G NR n7 : 2500 MHz ~ 2570 MHz 5G NR n12 : 699 MHz ~ 716 MHz 5G NR n25 : 1850 MHz ~ 1915 MHz 5G NR n30 : 2305 MHz ~ 2315 MHz 5G NR n38 : 2570 MHz ~ 2620 MHz 5G NR n41 : 2496 MHz ~ 2690 MHz 5G NR n66 : 1710 MHz ~ 1780 MHz 5G NR n71: 663 MHz ~ 698 MHz 5G NR n77 : 3450MHz ~ 3550MHz, 3700 MHz ~ 3980 MHz WLAN 2.4 GHz Band: 2400 MHz ~ 2483.5 MHz WLAN 5.2 GHz Band: 5150 MHz ~ 5250 MHz WLAN 5.3 GHz Band: 5250 MHz ~ 5350 MHz WLAN 5.6 GHz Band: 5470 MHz ~ 5725 MHz WLAN 5.8 GHz Band: 5725 MHz ~ 5850 MHz WLAN 5.8G UNII4 Band: 5850 MHz ~ 5895 MHz WLAN 6E: 5925 MHz ~ 6425 MHz, 6425 MHz ~ 6525 MHz, 6525 MHz ~ 6875 MHz, 6875 MHz ~ 7125 MHz Bluetooth: 2400 MHz ~ 2483.5 MHz NFC : 13.56 MHz WPT: 110KHz ~ 148.5KHz UWB: 6489.6 MHz, 7987.2 MHz Mode GSM/GPRS/EGPRS RMC/AMR 12.2Kbps HSDPA HSUPA LTE: QPSK, 16QAM, 64QAM, 256QAM 5G NR: DFT-s-OFDM/CP-OFDM, Pi/2 BPSK/QPSK/16QAM/64QAM/256QAM WLAN: 802.11a/b/g/n/ac/ax HT20/HT40/VHT20/VHT40/VHT80/VHT160/HE20/HE40/HE80/HE160 Bluetooth BR/EDR/LE NFC:ASK WPT: ASK UWB: BPM-BPSK Remark: 1. Enable SP mode for UNII-5 and UNII-7. Reviewed by: Jason Wang Report Producer: Paula Chen TEL : 886-3-327-3456 Page : 5 of 16 FAX : 886-3-328-4978 Issued Date : Nov. 29, 2022 Form version: 180516 FCC RF EXPOSURE REPORT Report No. : FA121931-25A 2. Maximum Tune-up Limit (unit: dBm) General Note: 1. For each cellular band, the device has 5 antennas, the antenna selection is based on the connection quality condition, and only one antenna will transmit at a time. 2. The maximum power of the WWAN antenna will be selected to evaluate the power density 3. For MPE calculation is using the highest output among 2Tx switching antennas for each frequency band. <WWAN Maximum Power> Maximum Transmit Power Level (dBm) Band Config Antenna duty cycle Default Index 1 GSM850 GPRS 1TX TX0 0 12.50% 34.0 GSM850 GPRS 2TX TX0 0 25.00% 32.5 GSM850 GPRS 3TX TX0 0 37.50% 31.5 GSM850 GPRS 4TX TX0 0 50.00% 30.5 GSM850 EDGE 1TX TX0 0 12.50% 28.0 GSM850 EDGE 2TX TX0 0 25.00% 27.5 GSM850 EDGE 3TX TX0 0 37.50% 27.5 GSM850 EDGE 4TX TX0 0 50.00% 25.5 GSM1900 GPRS 1TX TX0 2 12.50% 31.0 GSM1900 GPRS 2TX TX0 2 25.00% 29.5 GSM1900 GPRS 3TX TX0 2 37.50% 29.0 GSM1900 GPRS 4TX TX0 2 50.00% 28.0 GSM1900 EDGE 1TX TX0 2 12.50% 26.0 GSM1900 EDGE 2TX TX0 2 25.00% 25.0 GSM1900 EDGE 3TX TX0 2 37.50% 25.0 GSM1900 EDGE 4TX TX0 2 50.00% 24.0 WCDMA B2 TX0 2 100.00% 25.25 WCDMA B4 TX0 2 100.00% 25.25 WCDMA B5 TX0 0 100.00% 25.4 LTE B7 TX0 2 100.00% 25.5 LTE B12/17 TX0 0 100.00% 25.5 LTE B13 TX0 0 100.00% 25.5 LTE B14 TX0 0 100.00% 25.5 LTE B25/2 TX0 2 100.00% 25.5 LTE B26/5 TX0 0 100.00% 25.5 LTE B30 TX0 2 100.00% 25.5 LTE B41/B38 PC3 TX0 2 63.30% 25.5 LTE B38 PC2 TX0 2 43.30% 27 LTE B41 PC2 TX0 2 43.30% 27.5 LTE B48 TX0 6 63.30% 25.5 LTE B66/4 TX0 2 100.00% 25.5 LTE B71 TX0 0 100.00% 25.5 FR1 n25/2 TX0 2 100.00% 25.5 FR1 n5 TX0 0 100.00% 25.5 FR1 n7 TX0 2 100.00% 25.5 FR1 n12 TX0 0 100.00% 25.5 FR1 n30 TX0 2 100.00% 25.5 FR1 n41/38 PC3 TX0 5 100.00% 25.5 FR1 n41/…

Text truncated - open the document above for the full version.

0 dB = 2.44 W/kg = 3.87 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/4 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW ; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210704 Medium parameters used: f = 750 MHz; σ = 0.898 S/m; ε r = 42.686; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration - Probe: ES3DV3 - SN3124; ConvF(6.36, 6.36, 6.36) @ 750 MHz; Calibrated: 2020/11/23 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1311; Calibrated: 2020/8/25 - Phantom: SAM_Left; Type: QD 000 P40 CD; Serial: TP:1801 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.47 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 53.87 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 2.90 W/kg SAR(1 g) = 2.13 W/kg; SAR(10 g) = 1.46 W/kg Maximum value of SAR (measured) = 2.44 W/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/9 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW ; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210709 Medium parameters used: f = 750 MHz; σ = 0.883 S/m; ε r = 43.146; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration - Probe: ES3DV3 - SN3124; ConvF(6.36, 6.36, 6.36) @ 750 MHz; Calibrated: 2020/11/23 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1311; Calibrated: 2020/8/25 - Phantom: SAM_Left; Type: QD 000 P40 CD; Serial: TP:1801 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.17 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 50.55 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 2.75 W/kg SAR(1 g) = 1.92 W/kg; SAR(10 g) = 1.29 W/kg Maximum value of SAR (measured) = 2.21 W/kg 0 dB = 2.17 W/kg = 3.36 dBW/kg 0 dB = 2.46 W/kg = 3.91 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/11 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW ; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210711 Medium parameters used: f = 750 MHz; σ = 0.908 S/m; ε r = 42.996; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration - Probe: ES3DV3 - SN3124; ConvF(6.36, 6.36, 6.36) @ 750 MHz; Calibrated: 2020/11/23 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn393; Calibrated: 2021/4/9 - Phantom: SAM_Left; Type: QD 000 P40 CD; Serial: TP:1801 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.49 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 53.78 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 2.92 W/kg SAR(1 g) = 2.15 W/kg; SAR(10 g) = 1.47 W/kg Maximum value of SAR (measured) = 2.46 W/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/12 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW ; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210712 Medium parameters used: f = 750 MHz; σ = 0.902 S/m; ε r = 42.656; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.6 °C DASY5 Configuration - Probe: ES3DV3 - SN3124; ConvF(6.36, 6.36, 6.36) @ 750 MHz; Calibrated: 2020/11/23 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn393; Calibrated: 2021/4/9 - Phantom: SAM_Left; Type: QD 000 P40 CD; Serial: TP:1801 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.48 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 53.78 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 2.90 W/kg SAR(1 g) = 2.13 W/kg; SAR(10 g) = 1.47 W/kg Maximum value of SAR (measured) = 2.44 W/kg 0 dB = 2.44 W/kg = 3.87 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/12 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210712 Medium parameters used: f = 750 MHz; σ = 0.89 S/m; ε r = 42.563; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.6 °C DASY5 Configuration - Probe: EX3DV4 - SN3642;ConvF(9.09, 9.09, 9.09) @ 750 MHz;Calibrated: 2021/4/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn917; Calibrated: 2020/12/22 - Phantom: Twin-SAM V5.0_LEFT; Type: QD 000 P40 CD; Serial: 1718 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.81 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 58.51 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 3.22 W/kg SAR(1 g) = 2.08 W/kg; SAR(10 g) = 1.34 W/kg Maximum value of SAR (measured) = 2.83 W/kg 0 dB = 2.83 W/kg = 4.52 dBW/kg 0 dB = 0.526 W/kg = -2.79 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/12 System Check_Head_750MHz DUT: D750V3-1107 Communication System: CW; Frequency: 750 MHz;Duty Cycle: 1:1 Medium: HSL_750_210712 Medium parameters used: f = 750 MHz; σ = 0.89 S/m; ε r = 42.563; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.6 °C DASY5 Configuration - Probe: EX3DV4 - SN3976;ConvF(10.6, 10.6, 10.6) @ 750 MHz;Calibrated: 2021/1/27 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) …

Text truncated - open the document above for the full version.

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/16 #01_GSM850_GPRS (4 Tx slots)_Right Cheek_Ch251;Ant 1 Communication System: GSM850; Frequency: 848.8 MHz;Duty Cycle: 1:2.08 Medium: HSL_850_210716 Medium parameters used: f = 849 MHz; σ = 0.928 S/m; ε r = 43.189; ρ = 1000 kg/m 3 Ambient Temperature：23.3 °C; Liquid Temperature：22.3 °C DASY5 Configuration - Probe: EX3DV4 - SN3642;ConvF(8.92, 8.92, 8.92) @ 848.8 MHz;Calibrated: 2021/4/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn656; Calibrated: 2021/1/22 - Phantom: Twin-SAM V5.0_LEFT; Type: QD 000 P40 CD; Serial: 1718 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Area Scan (81x101x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.19 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 24.50 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 1.64 W/kg SAR(1 g) = 0.717 W/kg; SAR(10 g) = 0.418 W/kg Maximum value of SAR (measured) = 1.22 W/kg 0 dB = 1.22 W/kg = 0.86 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/16 #02_GSM1900_GPRS (3 Tx slots)_Left Cheek_Ch512;Ant 0 Communication System: PCS; Frequency: 1850.2 MHz;Duty Cycle: 1:2.77 Medium: HSL_1900_210716 Medium parameters used : f = 1850.2 MHz; σ = 1.393 S/m; ε r = 38.391; ρ = 1000 kg/m 3 Ambient Temperature：23.3 °C; Liquid Temperature：22.3 °C DASY5 Configuration - Probe: EX3DV4 - SN3642;ConvF(7.97, 7.97, 7.97) @ 1850.2 MHz;Calibrated: 2021/4/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn656; Calibrated: 2021/1/22 - Phantom: Twin-SAM V5.0_LEFT; Type: QD 000 P40 CD; Serial: 1718 - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Area Scan (71x121x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 0.211 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 10.14 V/m; Power Drift = -0.18 dB Peak SAR (extrapolated) = 0.257 W/kg SAR(1 g) = 0.156 W/kg; SAR(10 g) = 0.095 W/kg Maximum value of SAR (measured) = 0.216 W/kg 0 dB = 0.216 W/kg = -6.66 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2021/7/9 #03_WCDMA II_RMC 12.2Kbps_Left Cheek_0mm_Ch9538;Ant 0 Communication System: WCDMA; Frequency: 1907.6 MHz;Duty Cycle: 1:1 Medium: HSL_1900_210709 Medium parameters used: f = 1908 MHz; σ = 1.438 S/m; ε r = 38.836; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.6 °C DASY5 Configuration - Probe: EX3DV4 - SN3642;ConvF(7.97, 7.97, 7.97) @ 1907.6 MHz;C…

Text truncated - open the document above for the full version.