AB6OUD850S8000Broadband GSM Base Station

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 July 16, 2002 RE: FCC ID: AB6OUD850S8000 Attention: Glen Moore I have a few comments on this Application. 1 While not changing the actual spurious limits at the terminal, the report should still use the highest conducted power measured. This would be 44.32dBm not 43.9dBm as stated in the report. As you are aware the number still comes out to –13dBm, but the report should be correct. This does not affect the issuance of the grant and is FYI. 2 Licensed devices require a tune up procedure as part of the submittal. Please provide this tune up procedure. 3 Several channels are listed in the report and in the technical report that their power level must be reduced by 2dB in order to pass. Please provide the steps taken in the tune up procedure for setting the reduced power of these channels. 4 Please note that radiated substitution measurements are done using the measured power of the fundamental not the power listed in the brochure or advertisements. The measured power of this system according to the test report was 44.32dBm or 27Watts. Thus the formula on page 7 of exhibit 2B should use 27W not 30 watts. While this is not a significant difference from using 30watts (and while the limit of 93.9dBuV is still the actual limit), since this is a submittal for certification, the report still must be accurate and must still reference the proper values. Please recalculate the limits and compare the results to this measured Power as specified in the rules. 5 Substitution measurements have not been required when the measured OATS data is greater than 20dB under the limit. Please note however, that page 16 of exhibit 2c clearly show margins of less than 10dB, thus requiring substitution measurements. Please provide substitution measurements for those radiated signals that are no greater than 20dB under the limit to support your statement on page 10 of exhibit 2B. Also please note that the 20dB under the limit exemption is no longer in the latest TIA EIA 603-A-2001. 6 Conducted data needs to be provided to support your Pass statement to 15.109 on page 10 of exhibit 2B. Please provide evidence of compliance to conducted limits other than by statement. 7 No conducted setup photos have been provided. Please provide these setup photos. 8 No Installation manual was provided. Please provide the users/installation manual. 9 Please separate the block diagrams from the technical data and provide as a separate file. They can still be confidential under the technical description request in the request for confidentiality. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. l Page 2July 16, 2002 Any questions about the content of this correspondence should be directed to the sender.

July 22, 2002 RE: FCC ID: AB6OUD850S8000 Attention: Denis Ward Responses to your comments: 1. Incorrect power used for spurious limits at terminals: Taken under advisement. 2. Tune up procedure: The tune up procedure is in ‘Exhibit 10 – Factory Test Specifications’. For this system all tune up checks are done on the system at the time of manufacture. 3. 2 dB power reduction requirement: See ‘Exhibit 1 – Application for Certification and Letters’ Page 9 – “Edge Channels 850 MHz Band Management” (also not that this problem is not present when the H2D is in place, which is the normal configuration) 4. Radiated substitution limits: Corrections page for Exhibit 2B is attached to this e-mail. 5. Substitution measurements: Exhibit 2C contains Part 24 data for 1900MHz radios that were also present in the system due to the fact that the system was tested in a mixed configuration of 850 and 1900MHz radios (see page 8 for configuration information). The emissions shown on page 16 are the 1900 MHz transmitter emissions, not spurious emissions from the system. The table on page 16 labels these results as “Measurements at transmitters frequencies for indicative level transmitter output connected to resistive 50 ohms loads”, thus indicating that these are transmitter, not spurious emissions. 6. Conducted Emissions Data – We are submitting this producted for certification to FCC Part 22/2 of the Rules, it is only required that Part 15 verification be performed. As the Part 22 spurious emissions were done in conjunction with the Part 15 emissions, the report contains info on both. I do not believe point 6 is valid 7. Conducted Emissions Photos: see item 6 8. No Installation/User Manual: See Exhibit 4A for Reference Manual. 9. Separate file for block diagrams: This has not been requested before by Bill, why is it necessary now? Please do not hesitate to call me to discuss any of the items above. Sincerely Glen Moore Technical Manager, EMC Design Services Sanmina-SCI 403-295-5144 (Ph) 403-295-4094 (Fax) 403-803-3794 (Cell) [email protected]

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 5 External Photographs Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 1 – S8000 Indoor with Front Panel Open This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 2 – S8000 Indoor Front View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 3 – S8000 Indoor Side View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 4 – S8000 Outdoor with Front Panel Open This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 5 – S8000 Outdoor Front View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 6 – S8000 Outdoor Side View

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 3 Transmit Label Photo Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 DRAWN APPD STREAM ISSUE SCALE B (V2 -FRAMEBUILDER 9511) A 2 3 4 5 6 BCD 1 2 3 4 5 6 ABCD DRAWING NUMBER SIZE TITLEINITIAL APPLICATION PROPRIETARY INFORMATION: THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF NORTHERN TELECOM LIMITED. EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY NORTHERN TELECOM LIMITED, THE HOLDER OF THIS DOCUMENT: (1) SHALL KEEP ALL INFORMATION CONTAINED HEREIN CONFIDENTIAL AND SHALL PROTECT SAME IN WHOLE OR IN PART FROM DISCLOSURE AND DISSEMINATION TO ALL THIRD PARTIES AND (2) SHALL USE SAME FOR OPERATING AND MAINTENANCE PURPOSES ONLY. 1/1 1 NORTEL NETWORKS SHEET1 of 2 LABEL : FCC Class B CSA P0986217 NTQA30FA EC 103-9737 25-07-2001 PHE ADE 01 01 NO TES: 1. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE EXPRESSED IN MILLIMETERS. TOLERANCESSHALL BE: 2 DECIMAL PLACES = +.25 3 DECIMAL PLACES = +.125 ALL LABEL CORNERS SHALL HAVE A .75 RADIUS. 2. TO CONVERT MILLIMETERS TO INCHES: 25.40 MILLIMETERS = 1 INCH. 3. THIS DESIGN FILE WAS CREATED IN ACCORDANCE WITH NT STD 1517.20. LABEL/ARTWORKS MUST BE MANUFACTURED IN ACCORDANCE WITH NPS90942. 4. THE ARTWORK (SEE SHEET 2) SHALL BE PLOTTED AT A MINIMUM OF 1200 DPI. THE TEXT FONT(S) SHALLBE: UNIVERS 67 CONDENSED BOLD PER NPS90942. TEXTABOVE AND BELOW UL SYMBOLS SHALL BE UNIVERS 57CONDENSED PER NPS90942. 5. MATERIAL: .25 CLEAR POLYCARBONATE PER R0115902 FINISH: VELVET/MATTE ADHESIVE: .05 PRESSURE SENSITIVE WITH PEEL OFF LINER PER R0113138 6. COLOURS SHALL CONFORM TO NORTHERN TELECOM OBSERVATIONAL STANDARD 2701.01. BACKGROUND: BTS LIGHT GREY PER NORTHERNTELECOM STANDARD S-33470TEXT AND GRAPHICS: NORTEL DARK GRAY PER NORTHERN TELECOM STANDARD S-33310BACKGROUND AT TOP OF LABEL: NORTEL LIGHTGRAY PER NORTHERN TELECOM STANDARD S-33310 7. LABEL TO BE REVERSE SCREEN PRINTED PER NPS90942-2. S8000 Outdoor BTSThis device complies with Part 15 of theFCC rules.Operation is subject to the condition that thisdevice does not cause harmful interference.This Class B digital apparatus meets allrequirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numérique de la classe B respectetoutes les exigences du Règlement Canadiensur le matériel causant des interferences.FCC Registration number: AB6USA-24176-WC-NComplies with Part 68, FCC RulesEnclosure Type:NEMA 3R IEC 529, IP55 208-240 V: 2W+N+PE40 A60 Hz 76.6 167.0 INFORMATION TECHNOLOGY EQUIPMENT 13.0 13.0 KISS-CUT Made in the U.S.A./Fabriqué aux E.-U. Remove this section, replacewith appropriate label below. 38.3 KISS-CUT Made in France/Fabriqué en France KISS-CUT IC: 332OUD850S8000TX FCC ID: AB6OUD850S8000 SHEET 2 o f 2 P0986217 STREAM 01/ ISSUE 01 FULL SCALE S8000 Outdoor BTSThis device complies with Part 15 of theFCC rules.Operation is subject to the condition that thisdevice does not cause harmful interference.This Class B digital apparatus meets allrequirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numérique de la classe B respectetoutes les exigences du Règlement Canadiensur le matériel causant des interferences.FCC Registration number: AB6USA-24176-WC-NComplies with Part 68, FCC RulesEnclosure Type:NEMA 3R IEC 529, IP55 208-240 V: 2W+N+PE40 A60 Hz INFORMATION TECHNOLOGY EQUIPMENT Made in the U.S.A./Fabriqué aux E.-U. Remove this section, replacewith appropriate label below. Made in France/Fabriqué en France TX FCC ID: AB6OUD850S8000 IC: 332OUD850S8000

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 6 Internal Photographs Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 1 – E-LDRX (Logic Board) Top View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 2 – E-LDRX (Logic Board) Bottom View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 3 – E-RDRX (Radio Board) Top View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 4 – E-RDRX (Radio Board) Bottom View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 5 – RX Splitter Top View This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. Figure 6 – RX Splitter Bottom View

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 9 RF Exposure Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 RF Exposure Calculation for the S8000 850 MHz GSM System Minimum Safe Distance: Uncontrolled mPGr td 62.1560*19.45300.0300.0=== Controlled mPGr td 03.760*19.45135.0135.0=== For a trisectored antenna G i = 18.7 dBi -> G d = 18.7-2.15 = 16.55 -> In linear units G d = 45.19 P t = 30 W * 2 transmitters = 60 W Where G d is the antenna gain related to a half wave dipole [dBi], and P t is the total power at the antenna terminals [Watts] (see page 6 of ‘RF Exposure Guidelines for Cellular, PCS and LMDS Antenna Sites’ for further details). Power Density Calculation: 22 222 /354.0/54.3 20 60*19.45*64.1*64.1 cmmWmW r ERP r EIRP S===== πππ The maximum permissible exposure is 0.58mW/cm 2 , therefore the system is below the limit. r = 20m for an antenna placed on a 20m tower. Where EIRP is Effective Isotropic Radiated Power, and ERP is Effective Radiated Power [Watts], and r is the closest distance accessible to public or trained personnel (see page 11 of ‘RF Exposure Guidelines for Cellular, PCS and LMDS Antenna Sites’ for further details). RF Exposure Guidelines for Cellular, PCS and LMDS Antenna Sites Document no: SI-EMR-R01.5 Authors: Product Integrity BWA – RF Engineering Microwave Radio Design Proprietary The information disclosed herein is proprietary to Nortel Networks or others and is not to be used by or disclosed to unauthorized persons without the written consent of Nortel. The recipient of this document shall respect the security status of the information. 1.0 Executive Summary This document serves as a guideline for the deployment and installation of Nortel Networks’ wireless base station equipment with respect to the control of electromagnetic radiation (EMR) exposure. The objective is to provide guidance on where antennas can be deployed, how to calculate power densities and safe distances and how to protect users from excessive exposure to electromagnetic radiation. This guideline is in response to recent regulatory requirements originating in the US aimed at controlling human exposure to EMR. Safe distance formulae for base stations: Limits Application Uncontrolled r [ meters ] Controlled r [ meters ] Cellular r0.300ERP= r0.135ERP= PCS r0.228ERP= r=0.102ERP DCS r0.228ERP= r = 0.102ERP LMDS r = 1 r = 0.4 P-to-P Microwave Radio r = 1 r = 0.4 Uncontrolled refers to situations where individuals are either unaware or not in control of their exposure to the electromagnetic fields in question. This typically pertains to the general public. Controlled refers to situations where individuals are both aware of and in control of their exposure to the electromagnetic fields in question. This typically pertains to trained staff that is in contact with these fields as a result of their employment and have authority to limit their exposure. Note: This document includes DCS in its examples. If the EU adopts ENV50166, or any other EMR standard, then that document will replace this as the guideline for DCS products. Until that happens, these limits can be used to ensure due diligence on Nortel Networks’ behalf. Northern Telecom Antenna Siting Guideline iii Table of Contents 1.0 Executive Summary ................................................................................. ii 2.0 Introduction ............................................................................................. 1 3.0 Guideline ............................................................................................. 2 3.1 MPE Limits ............................................................................................. 3 3.2 Safe Distance and Power Density Calculations ................................. 5 3.2.1 Minimum Safe Distance ............................................................ 6 3.2.2 Power Density Calculation ........................................................ 8 3.3 Site Planning ............................................................................................ 9 4.0 Other Components ................................................................................. 10 5.0 Assumptions ........................................................................................... 11 6.0 References .............................................................................................. 12 7.0 Acronyms ............................................................................................... 12 Northern Telecom Antenna Siting Guideline 1 2.0 Introduction Regulatory bodies in the US, Federal Communications Commission (FCC), and Canada, Health Canada, are imposing Maximum Permissible Exposure (MPE) limits. FCC’s OET Bulletin #65 (versions in progress) addresses calculation and measurement procedures to determine compliance with the FCC limits which includes the 800 MHz cellular and 1.9 GHz PCS bands. The equipment and its associated deployment must comply with FCC Guidelines, ET Docket No. 93-62, Released August 1, 1996, (FCC 96-326). This standard is largely based on the limits and test methods outlined in IEEE C95.1-1982, NCRP Report No. 86 and C95.3-1982 respectively. The applicable portions of both are summarized in this document to assist in the antenna site planning to ensure compliance. The exposure limits are currently in effect. The requirement for installers to evaluate the exposure at an installation takes effect on Sept. 1/97. The exposure limits should apply now to all known sites since existing facilities are not exempt or grand fathered from the new rules. The FCC has determined that certain sites will require “Environmental Evaluations” in order to show compliance to the standards. Adhering to these guidelines can ensure compliance to the standard, and therefore can be the basis for the Environmental Evaluation. Please n…

Text truncated - open the document above for the full version.

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 2 Test Report List Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. 850 MHz S8000 Test Reports 1. Exhibit 2A S8000 Radio Report 2. Exhibit 2B S8000 EMC Report 3. Exhibit 2C S8000 EMC Lab Report

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 2A S8000 Radio Report Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 S8000 Outdoor and Indoor BTS e-GSM 850 : FCC Part 22 exhibit document PE/BTS/DJD/263001.01 / ENApproved24/APR/2002Page 2/30 PUBLICATION HISTORY 24/APR/2002 Issue 01.01 / EN, Status Approved Creation S8000 Outdoor and Indoor BTS e-GSM 850 : FCC Part 22 exhibit document PE/BTS/DJD/263001.01 / ENApproved24/APR/2002Page 3/30 CONTENTS 1.INTRODUCTION........................................................................................................................... 5 1.1.OBJECT ................................................................................................................................. 5 1.2.S COPE OF THIS DOCUMENT ....................................................................................................... 6 2.RELATED DOCUMENTS.............................................................................................................. 6 2.1.A PPLICABLE DOCUMENTS .......................................................................................................... 6 2.2.R EFERENCE DOCUMENTS ......................................................................................................... 6 3.EXHIBIT 1: TEST REPORT .......................................................................................................... 7 3.1. INTRODUCTION ......................................................................................................................... 7 3.2. MEASUREMENTS RESULTS ......................................................................................................... 7 3.3. NAME OF TEST: 2.1046 RF POWER OUTPUT............................................................................... 8 3.3.1fcc requirements ............................................................................................................. 8 3.3.2test results...................................................................................................................... 8 3.3.3test procedure ................................................................................................................. 9 3.4. NAME OF TEST: 2.1049 OCCUPIED BANDWIDTH........................................................................ 10 3.4.1fcc requirements ...........................................................................................................10 3.4.2test results.................................................................................................................... 10 3.4.3test procedure ............................................................................................................... 11 3.5. NAME OF TEST: 2.1051 SPURIOUS EMISSIONS AT ANTENNA TERMINALS..................................... 12 3.5.1fcc requirements ...........................................................................................................12 3.5.2test results.................................................................................................................... 13 3.5.3test procedure ............................................................................................................... 21 3.6. NAME OF TEST: 2.1055 FREQUENCY STABILITY........................................................................ 23 3.6.1fcc requirements ...........................................................................................................23 3.6.2test results.................................................................................................................... 23 3.6.3test procedure ............................................................................................................... 24 3.7.M EASUREMENTEQUIPMENTLIST............................................................................................ 25 4.EXHIBIT 2 : UPDATED EQUIPMENT LIST................................................................................ 26 S8000 Outdoor and Indoor BTS e-GSM 850 : FCC Part 22 exhibit document PE/BTS/DJD/263001.01 / ENApproved24/APR/2002Page 4/30 5.EXHIBIT 3 : SCHEMATICS....................................................................................................... 28 5.1. E -DRX ASSEMBLY .................................................................................................................. 28 5.2. E-RDRX (RADIO BOARD)........................................................................................................ 28 5.3. E -LDRX (L OGIC BOARD )......................................................................................................... 28 5.4. E -SCPA ASSEMBLY ................................................................................................................. 28 5.5.R X SPLITTER ........................................................................................................................... 28 5.6. DUPLEXER .............................................................................................................................. 28 5.7. H 2 D ....................................................................................................................................... 28 6.ABBREVIATIONS AND DEFINITIONS...................................................................................... 29 6.1.A BBREVIATIONS ..................................................................................................................... 29 6.2. DEFINITIONS ........................................................................................................................... 29 S8000 Outdoor and Indoor BTS e-GSM 850 : FCC Part 22 exhibit document PE/BTS/DJD/263001.01 / ENApproved24/APR/2002Page 5/30 1.INTRODUCTION 1.1.OBJECT In complement with PCS/BTS/DJD/0743, this repor…

Text truncated - open the document above for the full version.

This document contains Proprietary Information of Northern Telecom Limited. This information is considered to be CONFIDENTIAL and should be treated appropriately. EXHIBIT 2B S8000 EMC Report Applicant: Northern Telecom Ltd. For Certification on: AB6OUD850S8000 This confidential document is the property of SANMINA-SCI, it must not be copied or circulated except in its entirety form. A SANMINA-SCI formal written agreement is required for any partial copy of this document. S8000 850 MHz : EMC Test Report Reference: Version: Status: Date: Nortel-STR-00297 03-en Approved 05/07/2002 Product Name: Frequency: Discipline: S8000 Indoor & Outdoor BTS 850 / 1900 MHz EMC Author: Verified by: Approved by: Y. BRUNETIERE T. LUCHINI C. CHANSARD Copyright  2002 SANMINA-SCI, All Rights Reserved S8000 850 MHz : EMC Test Report This confidential document is the property of SANMINA-SCI, it must not be copied or circulated except in its entirety form. A SANMINA-SCI formal written agreement is required for any partial copy of this document. Nortel-STR-00297 03-en Approved 05/07/2002 Page 2/12 PUBLICATION HISTORY VERSION DATE AUTHOR MODIFICATION 01-en 17/04/2002 Y. BRUNETIERE Creation of the document 02-en 02/07/2002 Y. BRUNETIERE Modification of the document 03-en 05/07/2002 Y. BRUNETIERE Modification of the document S8000 850 MHz : EMC Test Report This confidential document is the property of SANMINA-SCI, it must not be copied or circulated except in its entirety form. A SANMINA-SCI formal written agreement is required for any partial copy of this document. Nortel-STR-00297 03-en Approved 05/07/2002 Page 3/12 CONTENTS 1. INTRODUCTION ........................................................................................................................... 4 2. RELATED DOCUMENTS ............................................................................................................. 4 2.1. APPLICABLES DOCUMENTS ............................................................................................. 4 2.2. REFERENCE DOCUMENTS ................................................................................................ 4 3. TESTS RESULTS ......................................................................................................................... 5 3.1. TEST CONFIGURATION ...................................................................................................... 5 3.2. INSTALLATION DIAGRAM .................................................................................................. 8 3.3. MATRIX RESULTS ............................................................................................................... 9 4. CONCLUSION ............................................................................................................................ 10 5. ABBREVIATIONS AND DEFINITIONS ...................................................................................... 10 5.1. ABBREVIATIONS............................................................................................................... 10 5.2. DEFINITIONS ...................................................................................................................... 10 6. ANNEX 1 : HARDWARE TECHNICAL STATUS....................................................................... 11 6.1. S8000 INDOOR BTS........................................................................................................... 11 6.2. S8000 OUTDOOR BTS....................................................................................................... 12 S8000 850 MHz : EMC Test Report This confidential document is the property of SANMINA-SCI, it must not be copied or circulated except in its entirety form. A SANMINA-SCI formal written agreement is required for any partial copy of this document. Nortel-STR-00297 03-en Approved 05/07/2002 Page 4/12 1. INTRODUCTION The objective of this document is to present the tests report of the EMC testing on the S8000 850 MHz Indoor and Outdoor BTS. The qualification phase on the BTS has been done according to the FCC Part 15; 22 & 24 as defined by Nortel Networks. This document applies to : • Product : S8000 Indoor & Outdoor BTS • Manufacturer : Nortel Networks • Frequencies : 850 / 1900 MHz • Configuration : S4_4 (for Indoor BTS) and S44 (for Outdoor BTS) • Ancillary : No • Options : No 2. RELATED DOCUMENTS 2.1. APPLICABLES DOCUMENTS [A1] CFR 47 Part 2 Code of Federal Regulations - Part 2 - Frequency Allocations and Radio Treaty Matters. General Rules and Regulations. Date : June 1996. [A2] CFR 47 Part 15 Code of Federal Regulations - Part 15 - Radio Frequency Devices. [A3] CFR 47 Part 22 Code of Federal Regulations - Part 22 – Public Mobile Services [A4] CFR 47 Part 24 Code of Federal Regulations - Part 24 - Personal Communications Services. Date : June 1996. 2.2. REFERENCE DOCUMENTS [R1] Nortel-STP-00282 V01-en S8000 850 MHz : EMC Test Plan [R2] PE/BTS/DJD/2592 V03.01 Avis de livraison matériel d’une BTS S8000 850 GSM (Indoor BTS) [R3] PE/BTS/DJD/2592 V05.01 Avis de livraison matériel d’une BTS S8000 850 GSM (Outdoor BTS) [R4] 149 014 DK External report from GYL Technologies laboratory [R5] 149 015 DK External report from GYL Technologies laboratory S8000 850 MHz : EMC Test Report This confidential document is the property of SANMINA-SCI, it must not b…

Text truncated - open the document above for the full version.