ABZ89FC58045.7GHz Fixed Wireless (ISM)

AP_CMM2-UM-en May 2003 © 2003 Motorola, Inc. All rights reserved. Printed in the U.S.A. Canopy™ Access Point Cluster and Gen II Cluster Management Module USER MANUAL AP_CMM2 User ManualPage 2 of 49 NOTICES Important Note on Modifications Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. U.S. Federal Communication Commision (FCC) and Industry Canada (IC) Notification This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. In Canada, users should be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 – 5350 MHz and 5650 – 5850 MHz and these radars could cause interference and/or damage to license-exempt local area networks (LELAN). This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures:
Increase the separation between the affected equipment and the unit;
Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to;
Consult the dealer and/or experienced radio/TV technician for help. FCC ID: ABZ89FC3789IC: 109W-5200 FCC ID: ABZ89FC4816IC: 109W-5700 FCC ID: ABZ89FC5804 The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. European Community Notification Notification of Intended Purpose of Product Uses This product is a two-way radio transceiver suitable for use in Broadband RLAN systems. It uses operating frequencies which are not harmonized through the EC. All licenses must be obtained before using the product in any EC country. Declaration of conformity: Motorola declares the GHz radio types listed below comply with the essential requirements and other relevant provisions of Directive1999/5/EC. Relevant Specification EN 301 893 or similar - radio spectrum EN301489-17 - EMC EN60950 - safety AP_CMM2 User ManualPage 3 of 49 Product Details for Products Tested for Compliance with Relevant EC Directives (At this time, only the 5.7 GHz product has been tested for compliance with relevant EC directives.) Operating Frequency Range Maximum Transmitter Power Effective Isotropic Radiated Power (EIRP) Modulation Type Channel Spacing Access Point5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module 5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Backhaul5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 Mhz 20 MHz Backhaul with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Exposure Note The Canopy Subscriber Module (SM) must be installed to provide a separation distance of at least 20 cm (7.9 in) from all persons, when adding the Canopy reflector dish (in the 5.7 GHz band), the reflector dish must be installed to provide a separation distance of at least 1.5m (59.1 in) from all persons and does not emit a RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. In both configurations the maximum RMS power does not exceed 200mW. The applicable power density exposure limit is 10 Watt/m 2 , according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density ( S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is 2 4d GP S π ⋅ = In the case of the Canopy SM without reflector, the gain is 8 dBi (a factor of 6.3), so the peak power density equals the exposure limit at a distance of 10 cm. A four-fold additional compliance margin is artificially introduced by doubling the distance to 20 cm. In the case of the Canopy SM with reflector, the gain is 26 dBi (a factor of 400), so the peak power density equals the exposure limit at a distance of about 80 cm. An almost four-fold additional compliance margin is artificially introduced by defining the compliance distance of 1.5 m. The compliance distance is greatly overestimated in this case because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source. Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / AP_CMM2 User ManualPage 4 of 49 CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LE…

Text truncated - open the document above for the full version.

Canopy TM Backhaul Module USER MANUAL BH02-UM-en May 2003 © 2003 Motorola, Inc. All rights reserved. Printed in the U.S.A Backhaul User ManualPage 2 of 50 NOTICES Important Note on Modifications Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. U.S. Federal Communication Commision (FCC) and Industry Canada (IC) Notification This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. In Canada, users should be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 – 5350 MHz and 5650 – 5850 MHz and these radars could cause interference and/or damage to license-exempt local area networks (LELAN). This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures:
Increase the separation between the affected equipment and the unit;
Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to;
Consult the dealer and/or experienced radio/TV technician for help. FCC ID: ABZ89FC3789IC: 109W-5200 FCC ID: ABZ89FC4816IC: 109W-5700 FCC ID: ABZ89FC5804 The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. European Community Notification Notification of Intended Purpose of Product Uses This product is a two-way radio transceiver suitable for use in Broadband RLAN systems. It uses operating frequencies which are not harmonized through the EC. All licenses must be obtained before using the product in any EC country. Declaration of conformity: Motorola declares the GHz radio types listed below comply with the essential requirements and other relevant provisions of Directive1999/5/EC. Relevant Specification EN 301 893 or similar - radio spectrum EN301489-17 - EMC EN60950 - safety Backhaul User ManualPage 3 of 50 Product Details for Products Tested for Compliance with Relevant EC Directives (At this time, only the 5.725 to 5.825 GHz product has been tested for compliance with relevant EC directives.) Operating Frequency Range Maximum Transmitter Power Effective Isotropic Radiated Power (EIRP) Modulation Type Channel Spacing Access Point5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module 5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Backhaul5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 Mhz 20 MHz Backhaul with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Exposure Note The Canopy Subscriber Module (SM) must be installed to provide a separation distance of at least 20 cm (7.9 in) from all persons, when adding the Canopy reflector dish (in the 5.7 GHz band), the reflector dish must be installed to provide a separation distance of at least 1.5m (59.1 in) from all persons and does not emit a RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. In both configurations the maximum RMS power does not exceed 200mW. The applicable power density exposure limit is 10 Watt/m 2 , according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density ( S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is 2 4d GP S π ⋅ = In the case of the Canopy SM without reflector, the gain is 8 dBi (a factor of 6.3), so the peak power density equals the exposure limit at a distance of 10 cm. A four-fold additional compliance margin is artificially introduced by doubling the distance to 20 cm. In the case of the Canopy SM with reflector, the gain is 26 dBi (a factor of 400), so the peak power density equals the exposure limit at a distance of about 80 cm. An almost four-fold additional compliance margin is artificially introduced by defining the compliance distance of 1.5 m. The compliance distance is greatly overestimated in this case because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source. Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU Backhaul User ManualPage 4 of 50 ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EIT…

Text truncated - open the document above for the full version.

SPECIFICATIONS RF Operational Characteristics: Frequency range: 5.25 - 5.35 GHz and 5.75 - 5.85 GHz Modulation: High Index BFSK (optimized for interference rejection) Carrier to interference: 3 dB 10 -4 BER@-65 dbm Data rate: 10 Mbps Multipoint 10 Mbps Backhaul Operating range: Up to 2 Miles with integrated antenna in 5.2GHz Up to 10 miles with passive reflector in 5.7GHz Electrical: Power supply: Power over Ethernet (POE) 24 VDC @ 0.3AMP (Active State) Interface: RJ45 Auto Detect 10/100 BaseT— Half / Full Duplex Rate Auto Negotiated (802.3 Compliant) Environmental: Operating temperature: -30ºC to +55ºC (-40ºF to + 131ºF) Operating humidity: 100% condensing Wind survival: 190km/hour Dimensions: 11.75”H x 3.4”W x 1.1”D, 3.4”D (29.9cm x 8.6cm x 8.6cm) Weight: 0.5 Kg HARDWARE No FCC license is required for all components. 1008CK - Cluster Management Module Includes- GPS receiver Antenna for automatic AP synchronization Built-in Ethernet switch AC power supply for 6 Canopy AP Units and 2 Canopy BH Units 5200AP / 5700AP - Canopy AP Module Measures 11.75” x 3.4” x 3.4” 10/100baseT Ethernet connection UL-approved 5200SM / 5700SM - Canopy SM Module Measures 11.75” x 3.4” x 3.4” Single cable – standard RJ45, 8-pin Ethernet Simple indoor AC adapter UL-approved 5700BH - Canopy Backhaul Module BH Unit @ 5.8 GHz, non-interfering with 5200AP to 5200SM link 10/100baseT Ethernet connection UL-approved 300SS – Canopy Surge Supressor Optional surge suppressor for Ethernet cable connection. Outdoor mountable, and includes connection for a grounding tap. Rev/10/02 MOTOROLA, and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. All other productor service names are the property of their respective owners. © Motorola, Inc. 2002. www.motorola.com /canopy For more information please contact us : 1-866-515-5825 THE SHORTEST DISTANCE BETWEEN YOU AND HIGH-SPEED INTERNET DELIVERY Motorola Canopy ™ Broadband Wireless Internet Platform 5.2 GHz: FCC ID #: ABZ89FC3789 5.7 GHz: FCC ID #: ABZ89FC4816 MOTOROLA CANOPY WIRELESS BROADBAND INTERNET ACCESS Actual size of the Canopy Subscriber Module (SM) Unit A New Spectrum of Broadband Wireless Internet Service In today’s broadband communications environment, the demands on service providers can be overwhelming. From purchasing spectrum licenses to installing and operating cumbersome networks that sometimes fail to meet expectations to competing in an extremely challenging environment while striving to satisfy ever-demanding consumers, it’s enough to drive smaller entrepreneurs to other business opportunities. That is until now! Motorola’s new wireless broadband offering, the Canopy™ system makes delivering low-cost broadband wireless Internet to consumers and businesses alike faster and easier than ever before. That’s because the Motorola Canopy Broadband Wireless Internet Platform solution is easily deployed and extremely cost-effective, so service providers can focus on delivering high-speed, high-quality service to their customers. The Motorola Canopy solution delivers wireless broadband service, while also minimizing costs normally associated with large communications networks. With Canopy, Motorola brings radio technology to the Internet Service Provider market place. It’s simply the best solution for providing high-speed Internet to customers in the last mile. An Affordable Solution The Canopy wireless Internet solution operates in the Unlicensed National Information Infrastructure (U-NII) spectrum at 5.25-5.35 GHz and the Industrial, Scientific, and Medical (ISM) spectrum at 5.725 - 5.850 GHz. There is no need for spectrum acquisition or site licensing. Because the Canopy solution is wireless, start-up costs are more affordable than any other connectivity options. The Canopy system also eliminates the need to go through existing phone or cable networks. Simple Installation and Network Configurations A simple network design makes this solution easy to install. There is no need to run overhead or in-ground wire, install microwave or software – the equipment is streamlined, with built-in installation and deployment assistance, making it easier to get up and running faster. A single-site Motorola Canopy system can begin serving a surrounding two-mile community quickly in the 5.2 GHz band and up to 10-miles using a passive reflector in the 5.7 GHz band. What’s more, the Canopy Access Point Modules include all the network management, and diagnostic capabilities you’ll need to remotely control and monitor the network. Inherent Flexibility and Scalability The Canopy solution can be adapted to serve the needs of many customer communities. The Point-to-Multipoint application can serve households and small businesses. Or, use the Backhaul application as a dedicated data link for small business enterprises. Intelligent protocols make the deployment and operation of large wireless network easy and cost-effective. When your capacity needs increase, the Canopy solution is scalable to accommodate changing needs, wider geographic areas, larger populations, and higher traffic volumes. With its high tolerance for interference and directional antennas, adding new transmitters creates more capacity – not more interference. Your customers demand fast, dependable broadband service. Unlike the myriad of solutions available today, the Motorola Canopy solution can deliver with ease. With upload and download speeds as fast or faster than virtually every other service available today, the Canopy system can offer more than 6Mbps (aggregate data rates) to your customers now. Of course, upload and download speeds are affected by several factors so actual speeds may vary, but the potential to offer an incredible Internet experience is possible with the Motorola Canopy solution. The Motorola Canopy Subscriber Module (SM) is small and easy to install at the customer’s site, there’s no obtrusive equipment. The Canopy Access Point Module (AP) easily interfaces with your existin…

Text truncated - open the document above for the full version.

Canopy TM Subscriber Module USER MANUAL SM02-UG-en May 2003 © 2003 Motorola, Inc. All rights reserved. Printed in the U.S.A SM User ManualPage 2 of 34 NOTICES Important Note on Modifications Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. U.S. Federal Communication Commision (FCC) and Industry Canada (IC) Notification This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. In Canada, users should be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 – 5350 MHz and 5650 – 5850 MHz and these radars could cause interference and/or damage to license-exempt local area networks (LELAN). This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures:
Increase the separation between the affected equipment and the unit;
Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to;
Consult the dealer and/or experienced radio/TV technician for help. FCC ID: ABZ89FC3789IC: 109W-5200 FCC ID: ABZ89FC4816IC: 109W-5700 FCC ID: ABZ89FC5804 The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. European Community Notification Notification of Intended Purpose of Product Uses This product is a two-way radio transceiver suitable for use in Broadband RLAN systems. It uses operating frequencies which are not harmonized through the EC. All licenses must be obtained before using the product in any EC country. Declaration of conformity: Motorola declares the GHz radio types listed below comply with the essential requirements and other relevant provisions of Directive1999/5/EC. Relevant Specification EN 301 893 or similar - radio spectrum EN301489-17 - EMC EN60950 - safety SM User ManualPage 3 of 34 Product Details for Products Tested for Compliance with Relevant EC Directives (At this time, only the 5.725 to 5.825 GHz product has been tested for compliance with relevant EC directives.) Operating Frequency Range Maximum Transmitter Power Effective Isotropic Radiated Power (EIRP) Modulation Type Channel Spacing Access Point5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module 5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 MHz 20 MHz Subscriber Module with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Backhaul5.725 to 5.825 GHz 200mW RMS 1 Watt EIRPHigh Index BFSK 25 Mhz 20 MHz Backhaul with Reflector 5.725 to 5.825 GHz 200mW RMS 63 Watts EIRP High Index BFSK 25 MHz 20 MHz Exposure Note The Canopy Subscriber Module (SM) must be installed to provide a separation distance of at least 20 cm (7.9 in) from all persons, when adding the Canopy reflector dish (in the 5.7 GHz band), the reflector dish must be installed to provide a separation distance of at least 1.5m (59.1 in) from all persons and does not emit a RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. In both configurations the maximum RMS power does not exceed 200mW. The applicable power density exposure limit is 10 Watt/m 2 , according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density ( S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is 2 4d GP S π ⋅ = In the case of the Canopy SM without reflector, the gain is 8 dBi (a factor of 6.3), so the peak power density equals the exposure limit at a distance of 10 cm. A four-fold additional compliance margin is artificially introduced by doubling the distance to 20 cm. In the case of the Canopy SM with reflector, the gain is 26 dBi (a factor of 400), so the peak power density equals the exposure limit at a distance of about 80 cm. An almost four-fold additional compliance margin is artificially introduced by defining the compliance distance of 1.5 m. The compliance distance is greatly overestimated in this case because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source. Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU SM User ManualPage 4 of 34 ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUA…

Text truncated - open the document above for the full version.

FCC ID: ABZ89FC5804 Request for Confidentiality In accordance with 47 C.F.R. Section 0.459, we, Motorola Inc., hereby request confidentiality for the block diagram, schematic and product description presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. Motorola Inc.

Page 16 of 16 The fully assembled CANOPY Unit #0A003EF01D36

Page 15 of 16 CANOPY unit #0A003EF01D36, Radio Printe d Wiring Board (Component Side): CANOPY Unit #0A003EF01D36, Radio Prin ted Wiring Board (Solder Side):

Page 15 of 16 CANOPY unit #0A003EF01D36, Radio Printe d Wiring Board (Component Side): CANOPY Unit #0A003EF01D36, Radio Prin ted Wiring Board (Solder Side):

Page 1 of 16 CANOPY 5700ISM Radiated Test Testing for Compliance wi th FCC Part 15.247 when Op erated in the ISM Band 9 April 2003 Compliance testing with FCC rules part 15.247 was performed in radiated fashion since production CANOPY units have no RF connec tor. A test fixture was used to make power sp ectral density, maximum output power, and occ upied bandwidth measurements. A reference antenna replacing the UUT calibrate d the coupling factor for the test fixture. Measurements were made on CANOPY unit serial #0A003EF01D36. The test setup diagram is as follows: MEASURINGRECEIVER LO RF BB CANOPY TEST FIXTURE COMPUTER UUT POWER METER SPECTRUM ANALYZER GPIB INTERFACE SIGNAL GENERATOR SIGNAL GENERATOR COUPLER SCOPE 1234 DET SIGNAL GENERATOR POWERDIV POWER DIV POWERCOMB LOAD PAD PAD PAD PAD Page 2 of 16 Spectrum Analyzer Reference Level Calibration The silent carrier power at all test frequencies was normalized (via the RF attenua tor pads in the test station) to 0dBm in the analyzer plots. The dBm units in the plots can be translated to dBc. TX bit error test pattern wa s initiated at maximum transmit duty cycle an d data throughput for the radio under test. This will result in 97.7% duty cycle or an average power versus maximum power ratio of -0 .10dB. Page 3 of 16 15.247c. Band Edge Requirements The following plot shows that the CANOPY radio produces an acceptable out-of-band spect ral output when operated at the channel limits of 5735MHz at the lowest frequency, and 5840MHz at the highest frequency. The display line indicated the –20d B specification limi t for non- restricted out-of-ba nd spectral emissions. 2-Level FSK – 10Mb Signaling Page 4 of 16 4-Level FSK – 20Mb Signaling The test results indicated that the band-e dge spectral emissions were more than 20dB below the in-band power for both 2FSK and 4FSK modulation modes. The carrier freq uencies tested were 5735 and 5840MHz. Page 5 of 16 15.247d. Conducted Peak Power Spectral Density The plots showed below display the peak power spectral density results for the radi o operation in the frequency band 5725-5850M Hz. The carrier power (translated to a conducted measurement) at the antenna port was 22.6dBm maximum at 5735MHz. At 5785MHz the carri er power was 22.2dBm and 5840MHz the carrier power was 22.4dBm. The specification limit for this unit under test in the plots sho wn below was –14.6dBc (8dBm). 2-Level FSK – 10Mb Signaling 2FSK Modulation Results: The maximum peak power spectral density when measured in a 3kHz resolution bandwidth was –18.51dBc (3.89dBm) at the uppermost operating frequency of 5840MHz. At 5785MHz the maximum peak pow er spectral density was measured to be –18.58dBc (3.62dBm). Th e maximum peak power spectral density was measured to be -18.73dBc (3.87dBm) at the lowest operating frequency of 5735MHz. Page 6 of 16 4-Level FSK – 20Mb Signaling 4FSK Modulation Results: The maximum peak power spectral density when measured in a 3kHz resolution bandwidth was –18.81dBc (3.59dBm) at the uppermost operating frequency of 5840MHz. At 5785MHz the maximum peak pow er spectral density was measured to be –20.36dBc (1.84dBm). At the lowest operating frequency, 5735MHz the maximum peak pow er spectral density was meas ured to be –20.58dBc (2.02dBm). Page 7 of 16 CANOPY 5700ISM Radiated Test Testing for Compliance wi th FCC Part 15.209 when Op erated in the ISM Band 13 February 2003 A CANOPY 5700 ISM unit, serial #0A003EF01D36, was tested outdoors to check compliance with FCC requirement 15.209, restricted band emissions for ISM data-modulated radios. As the CANOPY ra dio is already type-approved fo r U-NII band operation, the tests performed here were limited to measurements of transmit harmonic energy and ISM transmit spectral mask. The testing was done using a model 3115 and a model 3116 calibrated dual-ridged waveguide-horn ante nnas manufactured by EMCO, I nc., an Agilent 8564EC 40GHz spectrum analyzer, an d a laptop to control the DUT and take data from the spectrum analyzer. The two a ntennas combined allowed a frequency measurement range of 1GHz to 40GHz . The spatial separation between the EMCO horn antennas and the DUT was maintained at 1 or 3 meters during the test. The FCC requirement for restricted band emi ssions is stated in terms of field strength at 500uV/m at a distance of 3 meters. U sing the free space impedance of 377 ohms, the equivalent power density is –61.78dBm/m 2 . This power density number was used as the pass/fail criteria for the test. Cable losses, antenna gains, and other correction factors were entered into an Excel spreadsheet along with the results of the testing. To calculate the power density at the horn antennas, the power level received by the an tenna is offset by the log ratio of the effective aperture of the antenna to one square meter. The calculation of the effective aperture is done using: A em = e cd ( λ 2 /4 π )D o, D o is the directivity of the antenna, e cd is the efficiency, a…

Text truncated - open the document above for the full version.