ABZ89FC5809900 MHz Fixed Wireless (ISM)

900-UG-en Issue 1, Draft 1 June 2004 Canopy TM 900 MHz Access Point (AP) and Subscriber Module (SM) User Guide Software Release Notes Canopy 900 MHz AP and SMUser Guide Issue 1, Draft 1 June, 2004Page 2 of 16 NOTICES Important Note on Modifications Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Notification This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures: • Increase the separation between the affected equipment and the unit; • Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to; • Consult the dealer and/or experienced radio/TV technician for help. FCC IDs and Industry Canada Certification Numbers are listed in the following table: NOTE: FCC and Industry Canada Testing is in Progress. The following table is provisional until certification. Module Types Operating Frequency Range Maximum Transmitter Power Reflector or AntennaFCC IDIndustry Canada Certification Number SM APISM 902 to 928 MHz1WMaxrad Model # Z1681, flat panel with 10 dBi gain Mars Model # MA-IS91-T2, flat panel with10 dBi gain MTI Model #MT-2630003/N, flat panel with 10 dBi gain ABZ89FC5809109W-9000ISM Exposure Note The antenna of a Canopy 900 MHz module must be installed to provide a separation distance of at least 80 cm (approx 32 in) from all persons. When so installed, the module’s RF field is within Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. The maximum RMS power does not exceed 1W. The applicable power density exposure limit is 10 Watt/m 2 , according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst- case scenarios. The peak power density (S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is 2 4d GP S π ⋅ = In the case of a 900 MHz Canopy SM or AP with an antenna gain of 10 dBi (a factor of 10) and correctly entered in the user interface as a 10 dBi gain antenna, the peak power density equals the exposure limit at a distance of 18 cm. A power compliance margin of over 20 is artificially introduced by setting the distance to 80 cm. Consider next the case of a 900 MHz Canopy SM or AP with a 12 dBi antenna (a factor of 15.85) set in error in the user interface as an 8 dBi gain antenna. In this case, the peak power density equals the exposure limit at a distance of 36 cm, still giving a power compliance margin of over 5. The compliance distance is greatly overestimated in these cases because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source. Software License Terms and Conditions ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO Canopy 900 MHz AP and SMUser Guide Issue 1, Draft 1 June, 2004Page 3 of 16 NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO USE THIS PRODUCT IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING TERMS. Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good and valuable consideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and Motorola agree as follows: Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal, revocable, non-assignable, non-transferable, non-exclusive and limited license to use on a single piece of equipment only one copy of the software contained on this disk (which may have been pre-loaded on the equipment)(Software). You may make two copies of the Software, but only for backup, archival, or disaster recovery purposes. On any copy you make of the Software, you must reproduce and include the copyright and other proprietary rights notice contained on the copy we have furnished you of the Software. Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the Software and any copies, including translations, compilations, derivative works (including images) partial copies and portions of updated works. The Software is Motorola’s (or its supplier's) conf…

Text truncated - open the document above for the full version.

900-UG-en Issue 2 August 2004 Canopy TM 900 MHz Access Point (AP) and Subscriber Module (SM) User Guide Software Release Notes Canopy 900 MHz AP and SMUser Guide Issue 2 August, 2004Page 2 of 16 NOTICES Important Note on Modifications Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority to operate the equipment and will void the manufacturer’s warranty. U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Notification This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures: • Increase the separation between the affected equipment and the unit; • Connect the affected equipment to a power outlet on a different circuit from that which the receiver is connected to; • Consult the dealer and/or experienced radio/TV technician for help. This device has been certifed with Industy Canada to operate with an antenna having a maximum gain of 10 dBi. Using an antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, Industry Canada requires the antenna type and its gain be chosen so that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. FCC IDs and Industry Canada Certification Numbers are listed in the following table: Module Types Operating Frequency Range RMS PowerReflector or AntennaFCC IDIndustry Canada Certification Number SM APISM 902 to 928 MHzUp to 0.4 W (26 dBm) Maxrad Model # Z1681, flat panel with 10 dBi gain Mars Model # MA-IS91-T2, flat panel with10 dBi gain MTI Model #MT-2630003/N, flat panel with 10 dBi gain ABZ89FC5809109W-9000ISM Exposure Note The antenna of a Canopy 900 MHz module must be installed to provide a separation distance of at least 60 cm (approx 24 inches) from all persons. When so installed, the module’s RF field is within Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. Per Health Canada Safety Code 6, the installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Currently certified 900 MHz antennas have an antenna gain of 10 dBi, which means they are limited to a maximum RMS power of 0.4 W (26 dBm) to remain within the regulatory limit of 4 W (36 dBm) for the 900 MHz frequency band. The applicable power density exposure limit for radios operating in the 900 MHz frequency band is 6 Watt/m 2 , according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density (S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is 2 4d GP S π ⋅ = In the case of a 900 MHz Canopy SM or AP with an antenna gain of 10 dBi (a factor of 10) and correctly entered in the user interface as a 10 dBi antenna, the peak power density equals the exposure limit at a distance of 23 cm. A power compliance margin of nearly 7 times is artificially introduced by setting the distance to 60 cm. The compliance distance is greatly overestimated in these cases because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source. Software License Terms and Conditions Canopy 900 MHz AP and SMUser Guide Issue 2 August, 2004Page 3 of 16 ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT / CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY), AND MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO USE THIS PRODUCT IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING TERMS. Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good and valuable consideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and Motorola agree as follows: Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal, revocable, non-assignable, non-transferable, non-exclusive and limited license to use on a single piece of equipment only one copy of the software contained on this disk (which may have been pre-loaded on the equipment)(Software). You may make two copies of the Software, but only for backu…

Text truncated - open the document above for the full version.

Page iii IC: 109W-9000 Model 9000 FCC:ABZ89FC5809 Request for Confidentiality We, Motorola Inc., hereby request confidentiality for the block diagram, schematic and product description presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. Motorola Inc.

Motorola, Inc., Canopy™Wireless Broadband Products 1299 E. Algonquin Road, Schaumburg, IL 60196 U.S.A. FCC ID: ABZ89FC5809 Product: Canopy Model 9000 (Canopy 900MHz) Justification for Professional Installation Professional Installation is required for the Canopy Model 9000 product because this product is not sold to the general public, requires “Aiming”, requires a link study, and requires radio configuration setup by an installer who is familiar with the installation process as defined by the Canopy User Manual. Motorola, Inc., Canopy™Wireless Broadband Products

57 MARS 58 MARS 59 MARS 60 MARS 61 MAXRAD 62 MAXRAD 63 MAXRAD 64 MAXRAD 65 MTI 66 MTI 67 MTI 68 MTI

900MHz Canopy Radio Mounted in Chassis – Component Side View 900MHz Canopy Radio Mounted in Chassis – RF Connector View 900MHz Canopy Radio Mounted in Chassis – Integrated Assembly 900MHz Canopy Radio Mounted in Chassis – Radio Label with FCC Identifier

49 CANOPY unit #0A003E9026, Radio Printed Wiring Board (Component Side with Shield): 50 CANOPY Unit #0A003E9026, Radio Printe d Wiring Board (Solder Side): 51 CANOPY unit #0A003E9031, Radio Printed Wiring Bo ard (Component Side without Shield): Shown for visual reference only 52 CANOPY unit #0A003E9031, Radio Printed Wiring Bo ard (Component Side without Shield): Shown for visual reference only

RF Exposure distance calculation The antenna of a Canopy 900 MHz module must be installed to provide a separation distance of at least 60 cm (approx 24 inches) from all persons. When so installed, the module’s RF field is within Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website http://www.hc-sc.gc.ca/rpb. Per Health Canada Safety Code 6, the installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Currently certified 900 MHz antennas have an antenna gain of 10 dBi, which means they are limited to a maximum RMS power of 0.4 W (26 dBm) to remain within the regulatory limit of 4 W (36 dBm) for the 900 MHz frequency band. The applicable power density exposure limit for radios operating in the 900 MHz frequency band is 6 Watt/m2, according to the FCC OET Bulletin 65, the ICNIRP guidelines, and the Health Canada Safety Code 6. The corresponding compliance distances referenced above have been determined by assuming worst-case scenarios. The peak power density (S) in the far-field of a radio-frequency source with rms transmit power P and antenna gain G at a distance d is S = P*G/4πd 2 In the case of a 900 MHz Canopy SM or AP with an antenna gain of 10 dBi (a factor of 10) and correctly entered in the user interface as a 10 dBi antenna, the peak power density equals the exposure limit at a distance of 23 cm. A power compliance margin of nearly 7 times is artificially introduced by setting the distance to 60 cm. The compliance distance is greatly overestimated in these cases because the far-field equation neglects the physical dimension of the antenna, which is modeled as a point-source.

1 Technical Brief CANOPY Model 9000 Radiated Test Testing for Compliance with FCC Pa rt 15.247 and RSS-210 Issue 5 Amendment when Operated in the ISM Band June 9th 2004 Compliance testing with FCC rules part 15.247 and RSS-210 Issue 5 Amendment of Industry Canada was performed in both radiated a nd conducted fashion since production CANOPY units have an external RF connector that conne cts to an external patch antenna array. Power spectral density, maximum output power, and occ upied bandwidth measurements were made in conducted fashion. Measurements were m ade on CANOPY unit serial #: 0A003E900026. The test setup diagram is as follows: MEASURINGRECEIVER LO RF BB CANOPY TEST FIXTURE COMPUTER UUT POWER METER SPECTRUM ANALYZER GPIB INTERFACE SIGNAL GENERATOR SIGNAL GENERATOR COUPLER SCOPE 1234 DET SIGNAL GENERATOR POWERDIV POWER DIV POWERCOMB LOAD PAD PAD PAD PAD 2 Spectrum Analyzer Calibration The silent carrier power at all test fre quencies was normalized (via the amplitude o ffset function in the spectrum analyzer) to maximum transmitted output power 28.0 dBm in the analyzer plots. The dBm units in the plots can be read directly fo r PSD. TX bit erro r test pattern was initiated at maximum transmit duty cycle and data throughput for the radio under test. This w ill result in 95.3% duty cycle or an average power versus maximum power ratio of -0.209dB. Note: The power out of the radio is controlled and limited based upon the dBi gain of the antenna. The canopy system is setup t o prevent exceeding 36dBm E.I.R.P. For every dB above 6dB our antenna is, th e output is reduced by one dB. This feature is set based on t he appropriate mating antenna. 15.247c. and RSS-210 Issue 5 6.2.2(o)(e1) Band Edge Requirements The following plot shows that the CANOPY radio produces an acceptable out-of-band spect ral output when operated at the channel limits of 906MHz at the lowest frequency, and 924MHz at the highest frequency. The display line indicated the –20dB from maximum in-band specification limit for non-restricted out-of-band spectral emissions. 2-Level FSK – 3.3Mb Signaling The test results indicated that the band-e dge spectral emissions were more than 20dB below the in-band power for both 2FSK and 4FSK modulation modes. The carrier frequenc ies tested were 906MHz 915MHz and 924MHz. 3 4-Level FSK – 6.6Mb Signaling The test results indicated that the band-e dge spectral emissions were more than 20dB below the in-band power for both 2FSK and 4FSK modulation modes. The carrier frequenc ies tested were 906MHz 915MHz and 924MHz. 4 Conducted data from 30MHz to 10 GHz, radio serial#OA003E900026 Carrier frequency is set to 906MHz. Note the display line is 20 dB below the carrier which is set for max power. 5 No spurious emissions were det ected that occurred w ithin the 20 dB window from 30MHz to 10GHz. 6 Carrier frequency is set to 915MHz. 7 No spurious emissions were det ected that occurred w ithin the 20 dB window from 30MHz to 10GHz. 8 Carrier frequency is set to 924MHz. 9 No spurious emissions were det ected that occurred w ithin the 20 dB window from 30MHz to 10GHz. 10 15.247d. and RSS-210 Issue 5 6.2.2(o) Amendment Conducted Peak Power Spectral Density The plots shown below display the peak pow er spectral density results for the radio operation in the fre quency band 902-928MHz. The carrier power (a conducted measurement) at the antenna connector was 27.974 dBm maximum at 915MHz. At 906MHz the carrier power was 27.923 dBm. At 924MHz the carrier power was 28.072 dBm 2-Level FSK – 3.3Mb Signaling PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 894E+6 896E+6 898E+6 900E+6 902E+6 904E+6 906E+6 908E+6 910E+6 912E+6 914E+6 916E+6 918E+6 Frequency (Hz) dBm PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 903E+6 905E+6 907E+6 909E+6 911E+6 913E+6 915E+6 917E+6 919E+6 921E+6 923E+6 925E+6 927E+6 Frequency (Hz) dBm PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 912E+6 914E+6 916E+6 918E+6 920E+6 922E+6 924E+6 926E+6 928E+6 930E+6 932E+6 934E+6 936E+6 Frequency (Hz) dBm 2FSK Modulation Results: The maximum peak power spectral densit y when measured in a 3kHz resolu tion bandwidth was measured to be 5.409dBm at the mid operating frequency of 915MHz. At the uppermos t operating frequency of 924MHz, the maximum peak power spec tral density was measured to be 4.973dBm. At the lowest operating frequency, 906MHz, the maximum peak power spectral density was measured to be 4.513dBm. The specification limit for this m easurement was 8dBm for the unit under test. The test results show we ha ve 2.591dB margin worst case. 11 4-Level FSK – 3.3Mb Signaling PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 894E+6 896E+6 898E+6 900E+6 902E+6 904E+6 906E+6 908E+6 910E+6 912E+6 914E+6 916E+6 918E+6 Frequency (Hz) dBm PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 903E+6 905E+6 907E+6 909E+6 911E+6 913E+6 915E+6 917E+6 919E+6 921E+6 923E+6 925E+6 927E+6 Frequency (Hz) dBm PSA/ESA Spectrum Analyzer (E4440A) -85-75-65-55-45-35-25-15 -5 5 912E+6 914E+6 916E+6 918E+6 920E+6 922E+6 924E+6 926E+6 928E+6 930E+6 932E+6 934E+6 936E+6 Frequency (Hz) dBm 4FSK Modulation Results: The maximum peak power spectral density when measured in a 3kHz resolution bandwidth was measured to be 2.775 dBm at the mid operating frequency of 915MHz. At the uppermost operating frequency of 924MHz , the maximum peak power spectral density was measured to b e 2.572 dBm. At the lowest operating frequency, 906MHz, the maximu m peak power spectral density was measured to be 2.524 dBm. The specification limit for this measurement was 8dBm for the unit under test. The test results show we ha ve 5.225dB margin worst case. 12 CANOPY Model 9000 Radiated Test Testing for Compliance with FCC Part 15.209 and RSS- 210 Issue 5 6.2.2(o) when Operated in the ISM Band June 9th 2004 CANOPY 9000 ISM units, serial #s: 0A003E00021, 0A003E900022, and 0A003E900026 were tested outdoors to check…

Text truncated - open the document above for the full version.

FCC Part 15 Class BVoltage Mains TestEUT: 9000 SM Manufacturer: Motorola Operating Condition: 73 deg. F, 70% R.H. Test Site: DLS OF Screen Room Operator: Craig Brandt Test Specification: 120 VAC, 60 Hz Comment: Line 1 transmit mode Date: 6/7/04 SCAN TABLE: "FCC ClassB Voltage" Short Description: FCC Class B Voltage Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 4.0 kHz MaxPeak 10.0 ms 9 kHz LISN DLS#128 Average 0 1020304050607080 Level [dBμV] 150k 300k 400k 600k 800k 1M 2M 3M 4M 5M 6M 8M 10M 20M 30M Frequency [Hz] + + + + + + + + + + + + x x x x x x x x x x x x x x x MES 6701_fin QP + + + MES 6701_fin AV MES 6701_pre PK MES 6701_pre AV LIM FCC ClassB V QP New Voltage Amplitude QP LimitLIM FCC ClassB V AV New Voltage Amplitude AVG Limit Page 1/2 6/7/2004 3:56PM 6701 MEASUREMENT RESULT: "6701_fin QP"6/7/2004 3:56PM Frequency Level Transd Limit Margin Line PE MHz dBμV dB dBμV dB 0.230000 51.20 10.8 62 11.3 1 --- 0.326000 49.40 10.5 60 10.2 1 --- 0.370000 46.40 10.4 59 12.1 1 --- 0.390000 44.20 10.4 58 13.9 1 --- 0.882000 19.70 10.3 56 36.3 1 --- 0.890000 19.70 10.3 56 36.3 1 --- 0.914000 19.30 10.3 56 36.7 1 --- 0.922000 19.30 10.3 56 36.7 1 --- 21.346000 53.70 11.6 60 6.3 1 --- 21.502000 50.00 11.7 60 10.0 1 --- 21.658000 49.50 11.7 60 10.5 1 --- 21.814000 47.70 11.7 60 12.3 1 --- MEASUREMENT RESULT: "6701_fin AV"6/7/2004 3:56PM Frequency Level Transd Limit Margin Line PE MHz dBμV dB dBμV dB 0.226000 23.90 10.8 53 28.7 1 --- 0.310000 24.20 10.5 50 25.8 1 --- 0.378000 21.80 10.4 48 26.5 1 --- 0.566000 8.40 10.4 46 37.6 1 --- 2.942000 13.30 10.1 46 32.7 1 --- 3.562000 12.70 10.2 46 33.3 1 --- 4.338000 9.90 10.4 46 36.1 1 --- 4.954000 14.10 10.6 46 31.9 1 --- 21.346000 41.50 11.6 50 8.5 1 --- 21.658000 40.10 11.7 50 9.9 1 --- 21.810000 42.00 11.7 50 8.0 1 --- 21.966000 40.10 11.7 50 9.9 1 --- Page 2/2 6/7/2004 3:56PM 6701

FCC Part 15 Class BVoltage Mains TestEUT: 9000 SM Manufacturer: Motorola Operating Condition: 73 deg. F, 70% R.H. Test Site: DLS OF Screen Room Operator: Craig Brandt Test Specification: 120 VAC, 60 Hz Comment: Line 2 transmit mode Date: 6/7/04 SCAN TABLE: "FCC ClassB Voltage" Short Description: FCC Class B Voltage Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 4.0 kHz MaxPeak 10.0 ms 9 kHz LISN DLS#128 Average 0 1020304050607080 Level [dBμV] 150k 300k 400k 600k 800k 1M 2M 3M 4M 5M 6M 8M 10M 20M 30M Frequency [Hz] + + + + + + + + + + + + x x x x x x x x x x x x x x x MES 6702_fin QP + + + MES 6702_fin AV MES 6702_pre PK MES 6702_pre AV LIM FCC ClassB V QP New Voltage Amplitude QP LimitLIM FCC ClassB V AV New Voltage Amplitude AVG Limit Page 1/2 6/7/2004 4:02PM 6702 MEASUREMENT RESULT: "6702_fin QP"6/7/2004 4:02PM Frequency Level Transd Limit Margin Line PE MHz dBμV dB dBμV dB 0.290000 51.80 10.6 61 8.7 1 --- 0.302000 51.60 10.6 60 8.6 1 --- 0.310000 51.40 10.5 60 8.6 1 --- 0.318000 51.00 10.5 60 8.7 1 --- 0.878000 17.80 10.3 56 38.2 1 --- 0.886000 17.20 10.3 56 38.8 1 --- 0.898000 16.10 10.3 56 39.9 1 --- 0.918000 14.00 10.3 56 42.0 1 --- 21.146000 55.00 11.6 60 5.0 1 --- 21.302000 50.60 11.6 60 9.4 1 --- 21.610000 54.60 11.7 60 5.4 1 --- 21.766000 50.50 11.7 60 9.5 1 --- MEASUREMENT RESULT: "6702_fin AV"6/7/2004 4:02PM Frequency Level Transd Limit Margin Line PE MHz dBμV dB dBμV dB 0.218000 24.20 10.8 53 28.7 1 --- 0.286000 24.60 10.6 51 26.1 1 --- 0.370000 21.50 10.4 49 27.0 1 --- 0.774000 10.00 10.3 46 36.0 1 --- 2.934000 14.80 10.1 46 31.2 1 --- 3.706000 15.50 10.3 46 30.5 1 --- 4.326000 13.00 10.4 46 33.0 1 --- 4.942000 15.10 10.6 46 30.9 1 --- 21.146000 44.40 11.6 50 5.6 1 --- 21.610000 43.10 11.7 50 6.9 1 --- 21.762000 46.70 11.7 50 3.3 1 --- 21.918000 42.40 11.7 50 7.6 1 --- Page 2/2 6/7/2004 4:02PM 6702

53 54 55 56