ABZ89FC5827Non Broadcast Transmitter

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT D User Information User Information Tune-up and user / operational manual information are provided in the following exhibits. EXHIBIT DESCRIPTION D1 Tune-Up Procedure D2 User / Operational Manual APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT D1 User Information Tune-Up Procedure Aside from the 3 rd party cavity combiners, there is no field tune-up procedure. All adjustments are software controlled and are pre-set at the factory. Certain station operating parameters can be changed via man-machine interface (MMI) commands, within predetermined limits. Examples include transmit / receive operating frequencies and transmitter power level. For information on tuning the cavity combiners, which is required only if replaced in the field, please refer to the User / Operational Manual. APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT D2 User Information Operational or User’s Manual The manual should include instruction, installation, operator, or technical manuals with required ‘information to the users’. This manual should include a statement that cautions the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manual shall include RF Hazard warning statements, if applicable. This product is installed in restricted access locations only, thus only authorized service personnel have access to the product. As such, a high level User’s Installation / Operating instruction manual for the product is not published. Content from the document “MTS LITE, MTS 2 AND MTS 4 INSTALLATION, CONFIGURATION AND BASIC SERVICE MANUAL” (part number 6802800U74-AD, September 2014) has been included as part of this filing package. Due to space constraints, the full electronic version of this manual is not included in its entirety. The following chapters have been removed from the full document as these chapters are not intended for the general ‘user’: Chapter 3: Site Preparation Chapter 4: Hardware Installation Chapter 5: Interconnection and Internal Cabling Chapter 6: Configuration and Testing Chapter 13: MTS Troubleshooting Upon request, published manuals will be sent to the commission and/or telecommunication certification body (TCB). All of the descriptions, block diagrams, and schematics that are included in this filing package are current as of the package submittal date. MTS LITE, MTS 2 AND MTS 4 INSTALLATION, CONFIGURATION AND BASIC SERVICE MANUAL DIMETRA ™ Dimetra IP Scalable (DIPS) Dimetra IP Compact (DIPC)/Scalable Dimetra IP (SDIP) Dimetra IP Micro/Dimetra IP LiTE September 2014 *6802800U74* 6802800U74-AD © 2014 Motorola Solutions, Inc. All rights reserved Copyrights The Motorola products described in this document may include copyrighted Motorola computer programs. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola. © 2014 Motorola Solutions, Inc. All Rights Reserved No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Disclaimer Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a particular system, or may be dependent upon the characteristics of a particular mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola contact for further information. Trademarks MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. 3 | Copyrights 6802800U74-AD | September 2014 | Send Feedback CMM Labeling and Disclosure Table The People’s Republic of China requires that our products comply with China Management Methods (CMM) environmental regulations. (China Management Methods refers to the Regulation Management Methods for Controlling Pollution by Electronic Information Products.) Two items are used to demonstrate compliance; the Label and the Disclosure Table. The label is placed in a customer visible position on the product. The first of the following examples means that the product contains no hazardous substances; the second means that the product contains hazardous substances, and has an Environmental Friendly Use Period (EFUP) of fifty years. The Environmental Friendly Use Period (EFUP) is the period (in years) during which the Toxic and Hazardous Substances (…

Text truncated - open the document above for the full version.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C Photographs of the Device Photographs – Index EXHIBIT DESCRIPTION C1-1 External Front View of MTS 4 Cabinet and MTS 2 Cabinet C1-2 External Front View of MTS 4 C1-3 External Back / Top View Showing Location of Identification Label C1-4 FCC / IC Identification Label C2-1 Internal View – Site Controller Module C2-2 Internal View – Site Controller Circuit Board, Top View C2-3 Internal View – Site Controller Circuit Board, Bottom View C2-4 Internal View – Base Radio C2-5 Internal View – Transceiver Circuit Board, Top View C2-6 Internal View – Transceiver Circuit Board, Bottom View C2-7 Internal View – Power Amplifier Circuit Board, Top View C2-8 Internal View – Power Amplifier Circuit Board, Bottom View C2-9 Internal View – Power Supply Module APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C1-1 Photographs of the Device External Front View of MTS 4 Cabinet and MTS 2 Cabinet MTS 4 Base Radio Cabinet MTS 2 Base Radio Cabinet APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C1-2 Photographs of the Device External Front View of MTS 4

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT A1 Equipment Label FCC / IC Identification Numbers The FCC Identifier (FCC ID) is made up of the Grantee Code, supplied by the FCC, and an Equipment Product Code. This equipment product code may be to 14 characters in length, and is assigned by the grantee (applicant). The Grantee Code for this product is ABZ The Equipment Product Code for this product is 89FC5827 The entire FCC ID number is ABZ89FC5827 The Industry Canada (IC) identification consists of the certification / registration number as well as the IC model number. The certification / registration number is made up of Company Number (CN) assigned by Industry Canada, and the Unique Product Number (UPN) assigned by Motorola. The IC model number is the unique model number of the radio assigned by Motorola. The Company Number is 109AB The Certification / Registration Number for this product is 109AB-5827 The IC Model Number is MTS-800 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT A2-1 Equipment Label Details of FCC / IC Identification Label A representative image of the FCC / IC Identification label is shown below. This label is generated as part of the standard manufacturing process and is printed in the factory. Much of the information that is on the label, such as serial number, model number, etc. is driven by the ordering process and is unique per customer order. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received including interference that may cause undesired operation. Serial No: 895GJX0444 Model No: SQM07SUM0010A Type No: F957C TX FCC ID: ABZ89FC5827 IC: 109AB-5827 IC Model No: MTS-800 2x Input AC: 100-240V ; 11-5A ; 50-60 Hz 2x Input DC: -40.5 - -60V ; 20A 2x Batt. Output: -40.5 - -57V ; 6A Made by Motorola / Made in EC FCC / IC Identification Label, MTS 4 T h i s d e v ic e c om pl ie s w i th Pa rt 15 of t h e F C C R u l e s. Op e rat i on is subject to the following two conditions: (1) T h i s d e v ic e m ay no t ca us e h arm f u l interference and (2) this device must accept any interference received including interference that may cause undesired operation. Serial No: 895GJX0222 Model No: SQM07SUM0010A Type No: F957C TX FCC ID: ABZ89FC5827 IC: 109AB-5827 IC Model No: MTS-800 Input AC: 100-240V ; 11-5A ; 50-60 Hz Input DC: -40.5 - -60V ; 20A Batt. Output: -40.5 - -57V ; 6A Made by Motorola / Made in EC FCC / IC Identification Label, MTS 2 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT A2-2 Equipment Label Location of FCC / IC Identification Label The location of the identification label on both the MTS 4 and MTS 2 is placed on the top of the rack on the junction panel and is not covered by any doors, panels, etc. Location of FCC / IC Identification Label

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-1 Photographs of the Device Internal View – Site Controller Module APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-2 Photographs of the Device Internal View – Site Controller Circuit Board, Top View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-3 Photographs of the Device Internal View – Site Controller Circuit Board, Bottom View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-4 Photographs of the Device Internal View – Integrated Base Radio APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-5 Photographs of the Device Internal View – Transceiver Circuit Board, Top View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-6 Photographs of the Device Internal View – Transceiver Circuit Board, Bottom View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-7 Photographs of the Device Internal View – Power Amplifier Circuit Board, Top View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-8 Photographs of the Device Internal Back View – Power Amplifier Circuit Board, Bottom View APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT C2-9 Photographs of the Device Internal View – Power Supply Module

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT D1 User Information Tune-Up Procedure Aside from the 3 rd party cavity combiners, there is no field tune-up procedure. All adjustments are software controlled and are pre-set at the factory. Certain station operating parameters can be changed via man-machine interface (MMI) commands, within predetermined limits. Examples include transmit / receive operating frequencies and transmitter power level. For information on tuning the cavity combiners, which is required only if replaced in the field, please refer to the User / Operational Manual.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT E Report on Test Measurements Measurements Report The measurement report shows compliance information against the pertinent technical standards. Each parameter is measured generally at the low end, middle, and at the high end of the applicable frequency band. Each section of the report contains either verbiage or graphs which show compliance to applicable standards as required, explains testing method used, and indicates what the applicable specification is. A list of test equipment for and a certification signoff page are included at the end of the measurement report. SUBMITTED MEASURED DATA – INDEX EXHIBIT DESCRIPTION E1-1 RF Output-Data E1-2 Occupied Bandwidth, Digital Emissions: Setup, Specifications, and Index E1-2.1, 2, 3 DQPSK Modulation (TETRA) E1-2.4, 5, 6 64-QAM Modulation (TEDS) E1-3 Adjacent Channel Power, Digital Emissions: Setup, Specifications, and Index E1-3.1 MTS 4 ACP, DQPSK Modulation (TETRA) E1-3.2 MTS 4 ACP, 64-QAM Modulation (TEDS) E1-3.3 MTS 2 ACP, DQPSK Modulation (TETRA) E1-3.4 MTS 2 ACP, 64-QAM Modulation (TEDS) E1-4 Conducted Spurious Emissions: Setup, Specifications, and Index E1-4.1 MTS 4 Conducted Spurious Harmonic Emissions, Power 25 Watts (Average), DQPSK E1-4.2 MTS 4 Conducted Spurious Harmonic Emissions, Power 4 Watts (Average), DQPSK E1-4.3 MTS 4 Conducted Spurious Harmonic Emissions, Power 10 Watts (Average), 64-QAM E1-4.4 MTS 4 Conducted Spurious Harmonic Emissions, Power 2.5 Watts (Average), 64-QAM E1-4.5 MTS 2 Conducted Spurious Harmonic Emissions, Power 25 Watts (Average), DQPSK E1-4.6 MTS 2 Conducted Spurious Harmonic Emissions, Power 4 Watts (Average), DQPSK E1-4.7 MTS 2 Conducted Spurious Harmonic Emissions, Power 10 Watts (Average), 64-QAM E1-4.8 MTS 2 Conducted Spurious Harmonic Emissions, Power 2.5 Watts (Average), 64-QAM E1-4.9, 10, 11 MTS 4 Conducted Spurious Emission Spectrum, 200 MHz Span, Power 25 Watts, DQPSK E1-4.12, 13, 14 MTS 4 Conducted Spurious Emission Spectrum, 200 MHz Span, Power 10 Watts, 64-QAM E1-4.15, 16, 17 MTS 2 Conducted Spurious Emission Spectrum, 200 MHz Span, Power 25 Watts, DQPSK E1-4.18, 19, 20 MTS 2 Conducted Spurious Emission Spectrum, 200 MHz Span, Power 10 Watts, 64-QAM E1-5 Radiated Spurious Emissions: Setup, Specifications, and Index E1-5.1 Radiated Spurious Harmonic Emissions, Power 25 Watts (Average), DQPSK E1-5.2 Radiated Spurious Harmonic Emissions, Power 4 Watts (Average), DQPSK E1-5.3 Radiated Spurious Harmonic Emissions, Power 10 Watts (Average), 64-QAM E1-5.4 Radiated Spurious Harmonic Emissions, Power 2.5 Watts (Average), 64-QAM E1-6 Frequency Stability: Setup, Specifications, and Index E1-6.1 Frequency Stability Vs Temperature E1-6.2 Frequency Stability Vs Voltage E1-11 Test Equipment Used E1-12 Statement of Certification APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT E1-1 Report on Test Measurements RF Power Output Data The RF power output was measured with the indicated voltage applied to and current into the final RF amplifying device. The DC current indicated is the total for the final RF amplifier stage, consisting of three parallel power transistors. MTS 4 - DQPSK (TETRA) Modulation Mode: 851 MHz 860 MHz 869 MHz Measured RF output 24.3 25.1 25.4 Watts, Average DC Voltage, final RF amplifier stage/stages 28.0 28.0 28.0 Volts DC Current, final RF amplifier stage/stages 8.3 8.3 8.0 Amperes Input power for final RF amplifying device(s) 232 232 224 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC Minimum Measured RF output 3.9 4.0 3.9 Watts, Average DC Voltage, final RF amplifier stage/stages 28.0 28.0 28.0 Volts DC Current, final RF amplifier stage/stages 3.7 3.7 3.6 Amperes Input power for final RF amplifying device(s) 104 104 101 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC MTS 4 - 64-QAM (TEDS) Modulation Mode: 851 MHz 860 MHz 869 MHz Measured RF output 9.7 10.0 9.9 Watts, Average DC Voltage, final RF amplifier stage/stages 28.0 28.0 28.0 Volts DC Current, final RF amplifier stage/stages 5.5 5.3 5.3 Amperes Input power for final RF amplifying device(s) 154 148 148 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC Minimum Measured RF output 2.5 2.5 2.5 Watts, Average DC Voltage, final RF amplifier stage/stages 28.0 28.0 28.0 Volts Normal DC Current 3.2 3.2 3.2 Amperes Input power for final RF amplifying device(s) 90 90 90 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC MTS 2 - DQPSK (TETRA) Modulation Mode: 851 MHz 860 MHz 869 MHz Measured RF output 25.6 25.0 26.1 Watts, Average DC Voltage, final RF amplifier stage/stages 28.5 28.5 28.5 Volts DC Current, final RF amplifier stage/stages 7.9 7.9 7.9 Amperes Input power for final RF amplifying device(s) 225 225 225 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC Minimum Measured RF output 4.0 4.0 4.1 Watts, Average DC Voltage, final RF amplifier stage/stages 28.5 28.5 28.5 Volts DC Current, final RF amplifier stage/stages 3.6 3.6 3.5 Amperes Input power for final RF amplifying device(s) 103 103 100 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC MTS 2 - 64-QAM (TEDS) Modulation Mode: 851 MHz 860 MHz 869 MHz Measured RF output 10.9 10.0 11.2 Watts, Average DC Voltage, final RF amplifier stage/stages 28.5 28.5 28.5 Volts DC Current, final RF amplifier stage/stages 5.2 5.2 5.2 Amperes Input power for final RF amplifying device(s) 148 148 148 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC Minimum Measured RF output 2.8 2.5 3.0 Watts, Average DC Voltage, final RF amplifier stage/stages 28.6 28.6 28.6 Volts Normal DC Current 2.9 2.9 2.9 Amperes Input power for final RF amplifying device(s) 83 83 83 Watts Primary Radio Input Supply Voltage 48.0 48.0 48.0 Volts AC APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ89FC5827 109AB-5827 EXHIBIT E1-2 Report on Test Measurements Occupied Bandwidth –DQPSK (TETRA) Modulation and 64-QAM (TEDS) M…

Text truncated - open the document above for the full version.