ABZ89FT7604Mini-PCI Transmitter Card

i Mobile Laptop 900™ Model L3393, L3394 Motorola, Inc. Commercial, Government and Industrial Solutions Sector All rights reserved Owner’s Manual R02 Part No.: DDN 7415 TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice. Regulations Information Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: −Reorient or relocate the receiving antenna. −Increase the separation between the equipment and receiver. −Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. −Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Please note: The use of a non-shielded interface cable with this equipment is prohibited. Wireless LAN Module Statement FCC CAUTION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. To assure continued compliance (example – use only shielded interface cables when connecting to computer or peripheral devices), any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’ émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. SAFE USAGE NOTIFICATION: For reason of personal safety and optimal radio performance, Motorola has designed the ML900 with an intended purpose and position of use either in a secured vehicle docking station or on the top of an office desk. Motorola strongly recommends using this product in a vehicle only when it is physically-secured in a lock or assured-stationary location as failure to do so may cause the product to cause harm in accidents or other conditions. Similarly, Motorola strongly recommends that the unit not be situated for a prolonged period in an a position that places the antennas directly against the human body ( for example, by “tucking” an operational, radio-equipped unit under one’ s arm). NOTE: The radio modems in the ML900 may continue to transmit and receive signals even while the laptop is in a closed position. Failure to follow any part of this notification could cause degraded radio performance or harm to the user”. About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. SWEDISH VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. FINNISH VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste s…

Text truncated - open the document above for the full version.

3-10Managing Power CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. This chapter gives guidelines on installing and using these devices: l External monitor l USB device l Serial device l IR device l Bluetooth-capable device l IEEE 1394 device l Video capture device 4-2Expanding Your Computer Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor that supports the DVI interface to your computer. Follow this procedure to connect an external monitor: 1. Make sure that the computer is not turned on. 2. Plug the DVI adapter to the computer’s DVI-I port. 3. Plug the signal connector to the DVI adapter. 4. Plug the monitor’s power cord into an electrical outlet. 5. To use the monitor, turn on the monitor before turning on the computer. 6. The monitor should respond by default. If not, you can switch the display to the monitor or to both (simultaneous display), or to multi- display by pressing Fn + F9 . 7. You can change display settings through your operating system (Display Properties in Windows). See your operating system documentation or online help for specific information. CAUTION: Do not disconnect the external monitor while the computer is in Standby mode or Hibernation mode. If no external monitor is connected when the computer resumes, the LCD remains blank and the output is not displayed. Expanding Your Computer4-3 Connecting a USB Device NOTE: To take advantage of the USB 2.0 feature, the USB 2.0 driver supplied with your computer must be installed (see chapter 6). Your computer has four USB ports that supports transfer rates up to 12 MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as digital camera, scanner, printer, modem, and mouse. USB is specified to be an industry standard extension to the PC architecture. It supports “Plug-and-Play” technology so you can install and remove USB devices without turning off the computer. With its multiple connection capability, up to 127 devices can be connected in a daisy-chain configuration. In addition, you can use a USB hub that converts a single USB connector into multiple ports where USB devices can be connected. To connect a USB device, simply plug the device cable to one of the USB ports. 4-4Expanding Your Computer Connecting a Serial Device Your computer has a serial port for connecting a serial device such as an external modem. Follow this procedure to connect a serial device: 1. Make sure the “COM1 Ports” item is set properly in the SCU program. (See “Components Menu” in Chapter 5 for information.) 2. Make sure the computer is not turned on. 3. Plug the device cable to the serial port on the rear of the computer. 4. Turn on the computer. NOTE: Portable modems that derive power through the serial port cannot be used with the computer. Instead, use a modem that is powered by its own internal battery or external AC power. Expanding Your Computer4-5 Connecting an IR Device Your computer has an IR (infrared) port for connecting an infrared- equipped device wirelessly such as another computer, printer, or PDA (Personal Digital Assistant). Follow this procedure to connect an IR device: 1. Under Windows, make sure that the IrDA Fast Infrared Port is set to HP HSDL-2300/3600. (See “How to Use the Driver CD” in Chapter 6 for information.) 2. Make sure that the “COM Ports” and its “Mode Setting For COM2” items are set properly in the SCU program. (See “Components Menu” in Chapter 5 for information.) 3. When using the IR port: Place the transmitting device where its IR port faces the IR port of your computer within the effective range − within ±20-degrees vertical angle and within ±20-degrees horizontal angle at no greater than 0.8~1.0 meter distance. Place the receiving device where the IR port of your computer faces its IR port within the effective range − within ±15-degrees vertical angle and within ±15-degrees horizontal angle at no greater than 0.8~1.0 meter distance. 4. To take advantage of the IR communications, you need a third party software. NOTES: During infrared communication, take note of the following: l Do not move the computer and IR device. l Do not enter Standby mode. l Do not use a cell phone or another IR device near the computer. l Avoid strong light such as sunlight or fluorescent light. l Disable the screen saver. 4-6Expanding Your Computer Expanding Your Computer4-7 Connecting a Bluetooth-compliant Device (option) NOTE: To take advantage of the Bluetooth feature, the Bluetooth driver supplied with your computer must be installed (see chapter 6 for details). Your computer has a Bluetooth port for connecting a Bluetooth- compliant device wirelessly. Bluetooth is a short-range wireless communications technology. Devices with Bluetooth capabilities can exchange information over a distance of about 10 meters (30 feet) without requiring a physical connection. Unlike infrared, you do not need to line up the devices to beam information with Bluetooth. The devices only need to be within a range of about 10 meters. You can even beam information to a device in a different room, as long as it is within range. You may use Bluetooth in the following ways: • Beam Information – such as files, appointments, tasks, and contact cards, between devices that have Bluetooth capabilities. For example, if you and a co-worker each have a device with Bluetooth, you can beam items between your devices, such as files, contact cards, appointments, tasks, and so forth. • Create a dial-up modem connection – between your device and a Bluetooth phone. You can then use the Bluetooth phone as a modem. Bluetooth operates in three different modes: • On – the Bluetooth radio is turned on and you can use Bluetooth features. • Off – the Bluetooth radio is tu…

Text truncated - open the document above for the full version.

Installing Software Drivers6-5 PCI-952Shows you the instructions on installing the driver that allows you to use the optional wireless modem and GPS features to transmit information wirelessly. Upon clicking “Next Page,” the following screen appears: Drivers on the Third Page Mini-PCIShows you the instructions on installing the WLAN driver that allows you to use the internal Mini PCI WLAN card. USB-to-LANAllows you to use the network function of the computer when the optional docking station is connected. FingerprintShows you the instructions on installing the driver that allows you to use the fingerprint recognition system and its application software. 6-6Installing Software Drivers Video CaptureShows you the instructions on installing the driver that allows you to connect a video capture device through the AV input port. BluetoothAllows you to use the bluetooth port to connect to bluetooth-compliant devices. Touchscreen Driver To install the touch screen driver, perform the following: 1. Insert the driver CD into the drive. 2. Click on “Windows 2K”, then “Touchscreen” and follow the onscreen instructions to continue. 3. When finished installing, select “Yes” to reboot your system. The driver should now be loaded. 4. After the system has finished rebooting, click on the “PenMount Monitor” icon located on the taskbar to bring up the “PenMount Control Panel”. 5. Select the “Standard Calibration” folder and click on “OK.” 6. Click on “Advanced Calibration” button. 7. Click on the four sides (points) and the plus-sign “+” on the screen to calibrate your touchscreen for use on the computer. Installing Software Drivers6-7 Installing Drivers for Windows XP To set up the necessary drivers for Windows XP, click on “Windows XP” on the initial screen. The following screen appears: Drivers on the First Page To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. ApplicationInstalls the Intel® Application Accelerator to improve performance of the storage sub-system and overall system performance. This software delivers improved performance through several ingredient technologies (components). ChipsetEnsures the full function of the following drivers. Install this main chipset driver before installing the device drivers. 6-8Installing Software Drivers VGAAllows you to select high-resolution displays with richer colors. It can drive LCD displays as well as CRT displays. AudioAllows you to take full advantage of the audio subsystem. USB 2.0Allows your system to connect to USB 2.0 devices. Upon clicking “Next Page,” the following screen appears: Drivers on the Second Page TouchpadAllows you to take full advantage of the touchpad and the scroll button features. Mini-PCIShows you the instructions on installing the WLAN driver that allows you to use the internal Mini PCI WLAN card. PCI-952Shows you the instructions on installing the driver that allows you to use the optional wireless modem and GPS features to transmit information wirelessly. Installing Software Drivers6-9 TouchscreenAllows you to use your fingers as a pointing device on the LCD screen (refer to the next section for further instructions). Upon clicking “Next Page,” the following screen appears: Drivers on the Third Page USB-to-LANAllows you to use the network function of the computer when the optional docking station is connected. FingerprintShows you the instructions on installing the driver that allows you to use the fingerprint recognition system and its application software. Video CaptureShows you the instructions on installing the driver that allows you to connect a video capture device through the AV input port. BluetoothAllows you to use the bluetooth port to connect to bluetooth-compliant devices. 6-10Installing Software Drivers Touchscreen Driver To install the touchscreen driver, perform the following: 1. Insert the driver CD into the drive. 2. Click on “Windows XP”, then “Touchscreen” and follow the onscreen instructions to continue. 3. Click on ”Start,” then “Control Panel.” Installing Software Drivers6-11 4. Click on the “Performance and Maintenance” category. 5. Click on “System.” 6-12Installing Software Drivers 6. Click on “Hardware” folder, then click on “Device Manager.” Installing Software Drivers6-13 7. Click on “? Unknown device,” then click on the “Properties” icon. 6-14Installing Software Drivers 8. Click on “Reinstall Driver.” 9. When the “Hardware Update Wizard” appears, select “Install the software automatically [Recommended],” then click on “Next.” Installing Software Drivers6-15 10. Click on “Continue Anyway.” 11. Click on “Finish.” 6-16Installing Software Drivers 12. When the “PenMount DMC9000 and DMC9100 Properties” screen appears, click on “Close” to exit the driver installation. Touchscreen Utility To install the touchscreen utility, perform the following: 1. Insert the driver CD into the drive. Installing Software Drivers6-17 2. Click on “Start”, then “Run.” 3. Enter the following directory on the driver CD: \TSRC\Setup.exe, then click on “OK.” 4. Select “Yes” to the question if this is the first time to run this setup. 5. When the “InstallShield Wizard” appears, click on “Next” to continue. 6. Select “I accept the terms in the license agreement,” then click on “Next.” 7. When the “Ready to Install the Program” screen appears, click on “Next” to continue. 8. Reboot the system. 6-18Installing Software Drivers CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering these areas of maintenance: l How to protect the computer l What to note when using and storing the computer l How to clean the computer l What to note when using the battery pack l What to note when traveling with the computer 7-2Caring for the Computer Protecting the Computer To safeguard the integrity of your computer data…

Text truncated - open the document above for the full version.

May 10, 2004 Federal Communications Commission Equipment Approval Services 7435 Oakland Mills Road Columbia, MD 21046 Attn: Mr. Martin Perrine SUBJECT: Motorola, Inc. FCC ID: ABZ89FT7604 731 Confirmation No.: TC652525 Correspondence Reference No.: 12031 Request for Tech. Info.: 04/16/04 Dear Tim: Transmitted herewith, on behalf of Motorola Inc. is the answer to question #3 in response to the request for technical information dated April 14, 2004. Please find all other answers in Motorola’s Cover Letter. 1. To comply with Oct02 TCB Q/A Feb04 TCB training notes, the unit was tested with both simultaneous and single transmission and the worst case data was reported. We trust this information is sufficient to resolve FCC questions in this application. If you have any further questions, please do not hesitate to contact us. cc: Motorola, Inc.

To: Federal Communications Commission FCC Equipment Authorization Branch Attn: Tim Harrington From: Motorola Inc. Gary Moy Re: FCC ID ABZ89FT7604 / ABZ89FT7605 / ABZ89FT7606 Response to Audit Question 1: FCC ID label exhibit is wrong in Exhibit Types; Test Reports, ID Label, External Photos – Please Advise. Response: The issue was having both FCC ID and DOC on the labels. Motorola was informed that you can have one or the other, but not both on the same label. We have since made the corrections to the label by removing the DOC logo and keeping the FCC ID. Since labels have been pre-made, we will institute the running change once our current label stock is depleted. Question 2: Please submit antenna photo’s and location information. Response: Attachment of photo’s are enclosed. Question 4: Present FCC ID label refers to ABZ89FT7602. That ID is for one LAN and one Bluetooth in a laptop, with the LAN antenna in the handle. Does present filing use LAN antenna in the handle? Response: The LAN antenna is not in the handle. It is located on the top lid of the laptop. The manual has been updated to reflect this. Question 5: User manual page 2-23 discusses replacing the wireless LAN. How is compliance with 15.203 and 15.204 accomplished such that unauthorized LAN cards are not installed by the end-user? Response: Motorola’s intention was to certify multiple LAN cards as part of the release of the notebook computer. However, to this date, only one has been certified for use in the ML900. The plan is still to certify others, just not at this point. We’ve updated our manual to reflect this information, to only state that only one LAN card is certified. As for end-user replacement of the card, the card is not of the vintage PCMCIA type. It is a board that is attached to the main system board inside the computer. In order for it to be replaced by the end user, it would be near impossible. It requires taking apart the notebook computer to get to the main board. Question 6: User manual page 1-7 shows “Bluetooth port” – please describe. Is this a plug-in, internally installed, or what? Response: The Bluetooth Port is internally installed located in the left side of the notebook computer.

Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900 Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900 Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900 Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900 Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900 Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900

Digital Transmitter System (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC Measurement Report Reviewed by: Quality Manager Filename: 15. 240115110.ABZ Test Dates: Jan. 5-6, 2004 EUT Type: 2.4 GHz Wireless LAN Module FCC ID: ABZ89FT7604 Page 27 of 32 © 2004 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST EXHIBIT B – Labeling Requirements Sample Label & Location New Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The sample label shown below shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name, FCC ID, and the FCC logo must be displayed on the device per Section 15.19 (b)(2). Digital Transmitter System (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC Measurement Report Reviewed by: Quality Manager Filename: 15. 240115110.ABZ Test Dates: Jan. 5-6, 2004 EUT Type: 2.4 GHz Wireless LAN Module FCC ID: ABZ89FT7604 Page 28 of 32 © 2004 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST EXHIBIT B – Labeling Requirements (Cont.) Sample Label & Location FCC ID Label

Digital Transmitter System (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC Measurement Report Reviewed by: Quality Manager Filename: 15. 240115110.ABZ Test Dates: Jan. 5-6, 2004 EUT Type: 2.4 GHz Wireless LAN Module FCC ID: ABZ89FT7604 Page 27 of 32 © 2004 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST EXHIBIT B – Labeling Requirements Sample Label & Location New Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The sample label shown below shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name, FCC ID, and the FCC logo must be displayed on the device per Section 15.19 (b)(2). Digital Transmitter System (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC Measurement Report Reviewed by: Quality Manager Filename: 15. 240115110.ABZ Test Dates: Jan. 5-6, 2004 EUT Type: 2.4 GHz Wireless LAN Module FCC ID: ABZ89FT7604 Page 28 of 32 © 2004 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST EXHIBIT B – Labeling Requirements (Cont.) Sample Label & Location FCC ID Label

Motorola FCC ID: ABZ89FT7604 EUT Photographs © 2004 PCTEST Lab. 2.4 GHz Wireless LAN Module Model: ML900

© 2004 PCTEST Engineering Laboratory, Inc. PCTEST ENGINEERING LABORATORY, INC. 6660 – B Dobbin Road • Columbia, MD 21045 • USA Telephone 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com (email: [email protected]) CERTIFICATE OF COMPLIANCE MANUFACTURER NAME & ADDRESS: DATE & LOCATION OF TESTING: Motorola Inc. Date(s) of Tests: January 5-6, 2004 1301 East Algonquin, Room 1726 Test Report S/N: 15.240115110.ABZ Schaumburg, IL 60196 Test Site: PCTEST Lab, Columbia, MD FCC ID: ABZ89FT7604 APPLICANT: Motorola Inc. SUMMARY: Model No.: ML900 Equipment EUT Type: 2.4 GHz Wireless Lan Module Max. Output Power: 16.72 dBm Frequency Range: 2412 - 2462 MHz FCC Classification: FCC Part 15 Digital Transmission System (DTS) FCC Rule Part(s): Parts 15.247; ANSI C-63.4-2001 Test Device Serial No.: S/N: 1 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C-63.4-2001. This Wireless LAN is electrically identical to previously authorized FCC ID: PD9WM3B2100. RF conducted data is shown in that test report, included in this application. Grant Conditions: Limited Modular Approval. The output listed is conducted. This device is approved for use in the Motorola series ML-900 Notebooks. The antenna (s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter other than those approved for use in Motorola series ML- 900 Notebooks. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. I authorize and attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST certifies that no party to this application has been denied the FCC benefits pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C. 862. Digital Transmitter System (DTS), FCC Rule Part 15.247 PCTEST LAB TEST REPORT 15.247 FCC Measurement Report Reviewed by: Quality Manager Filename: 15. 240115110.ABZ Test Dates: Jan. 5-6, 2004 EUT Type: 2.4 GHz Wireless LAN Module FCC ID: ABZ89FT7604 Page i of i © 2004 PCTEST Engineering Laboratory, Inc. CONFIDENTIAL PROPERTY OF PCTEST TABLE OF CONTENTS ATTESTATION STATEMENTS.............................................................................................................................1 FCC PART 15.247 MEASUREMENT REPORT COVER PAGE............................................................................................2 1.0 INTRODUCTION.......................................................................................................................................................3 1.1 EVALUATION PROCEDURE........................................................................................................................................................................................................3 1.2 SCOPE.................................................................................................................................................................................................................................................3 1.3 PCTEST TEST LOCATION.............................................................................................................................................................................................................3 2.0 PRODUCT INFORMATION......................................................................................................................................4 2.1 EQUIPMENT DESCRIPTION........................................................................................................................................................................................................4 2.2 ENCLOSURE.....................................................................................................................................................................................................................................4 2.3 EMI SUPPRESSION DEVICE(S)/MODIFICATIONS.................................................................................................................................................................4 3.0 DESCRIPTION OF TEST.............................................................................................................................................5 3.1 CONDUCTED EMISSIONS..........................................................................................................................................................................................................5 3.2 RADIATED EMISSIONS.................................................................................................................................................................................................................6 4.0 ANTENNA REQUIREMENTS.....................................................................................................................................7 5.0 TEST EQUIPMENT CALIBRATION DATA...............................................................................................................8 EXHIBIT A. SUMMARY OF TE…

Text truncated - open the document above for the full version.