ABZ99FT3089VHF Portable Radio

M MOTOTRBO XPR TM 7550 Ex Color Display Portable User Guide 68009585001 68009585001-A Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: XPR 7550 Ex conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Contents English i ContentsThis User Guide contains all th e information yo u need to use the MOTOTRBO XPR Series Digital Portable Radios.Important Safety Info rmation . . . . . . . . . . . . . . . . . . 7 Product Safety and RF Exposure Compliance . . . 7 Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Computer Software Copyrights . . . . . . . . . . . . . . . . 8Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . . 9Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/Sys tem Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 4Attaching the Universal Connector Cover (Dust Cover) 4 Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5 Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6 Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7 Assignable Radio Functions . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . 9 Using the 4-Way Navigation Button . . . . . . . . . . . . . 9Accessing the Programmed Functions . . . . . . . . . . 10Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 11Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . 12Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 14 Identifying Status Indicators . . . . . . . . . . . . . . . . . . 15 Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Advanced Menu Icons . . . . . . . . . . . . . . . . . . . . . . 17Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 18LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Making and Receiving Calls . . . . . . . . . . . . . . . . . . 21 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contents English ii Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 22Receiving and Responding to a Radio Call . . . . . . 23 Receiving and Responding to a Group Call . . . . 23Receiving and Responding to a Private Call . . . 24Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 24Receiving and Responding to a Selective Call . . 25 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 26 Making a Call with the Chann el Selector Knob . . 26 Making a Group Call . . . . . . . . . . . . . . . . . . . . 26Making a Private Call . . . . . . . . . . . . . . . . . . . 27Making an All Call . . . . . . . . . . . . . . . . . . . . . . 28Making a Selective Call . . . . . . . . . . . . . . . . . 28 Making a Group, Private or All Call with the Programmable Number Key . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

English m XPR 7550 Ex Digital Portable Radios Quick Reference Guide *68009584001* 68009584001 -A 1 English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS ATTENTION! BEFORE USING THIS RADIO, READ THIS GUIDE WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL FOR COMPLIANCE WITH APPLICABLE STANDARDS AND REGULATIONS. 2 English RF Energy Exposu re Awareness and Control Informatio n and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for exam ple, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection.All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific 3 English operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it.Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) RegulationsWhen two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure StandardsYour Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at 4 English operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:• United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • FCC, OET Bulletin 65• Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 &• Industry Canada RSS-102• Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. 5 English RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposur e and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures.• DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. Two-Way Radio Operation• Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • In front of the face. Hold the radio in a vertical position with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips. Keeping the radio at a proper distance is important to ensure compliance. NOTE: RF exposures decrease with increasing distance from the antenna. • Body Worn Operation. When worn on the body, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. Using approved body-worn accessories is important because the use of non-Motorola-approved accessories ma y result in exposure 6 English levels, which exceed the occupational/controlled environment RF exposure limits. • Use only Motorola-approved …

Text truncated - open the document above for the full version.

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 2 SHEET 1 OF 1 EXHIBIT 2 STATEMENT OF CERTIFICATION - Pursuant to 47 CFR 2.907 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received an Electrical and Electronic Engineering degree from National University Malaysia (UKM). 2) I have 8 years experience in developing, testing, and certifying Portable Communications Products. NAME: Yap Soon Leng SIGNATURE: DATE: November 5, 2012 POSITION: Electrical Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Lee Szu See SIGNATURE: DATE: November 5, 2012 POSITION: Engineering Section Manager

FCC ID: ABZ99FT3089 EXHIBIT 13C __________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 April 2 nd , 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification. Gentlemen: The XPR7550 Ex VHF, 1.05 W Rated Power, Portable 2-Way radio is designed to operate in the frequency band 136-174 MHz. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola Solutions is requesting that the FCC lists the frequencies 136-174 MHz on the FCC Grant. For the FCC’s Rule Parts 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCC’s KDB 634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that it is a violation of the FCC Rules if this device operates on unauthorized frequencies. Sincerely, Mike Ramnath (signed above) Manager, Regulatory Compliance Email: [email protected]

FCC ID: ABZ99FT3089 __________________________________________________________ 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322. May 29 th , 2013 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Att: JC Chen Subject: Response to third Correspondence 42860 for Certification of Transmitter with FCC ID: ABZ99FT3089, Correspondence Number 146332, Confirmation Number TC592292 Hello Mr. Chen, Please see below for our responses to your April 23, 2013 email: 1. According to your 4/3 reply to my 3/28 inquiry the grantee appears to have compared test results against some specific rule sections in Part 22 and Part 80. Please revise the test report to incorporate this information and completely show how compliance with all applicable rule section is achieved for Part 22 Subpart E, Part 74 Subpart D and Part 80. The TCB (and FCC in the case of PBA or audit) would then review accordingly and ask for additional information if necessary. Response: We have amended our test report in the prior correspondence as requested to further show that we have complied to FCC Rule Parts 22, 74, and 80. If you require any additional information, please contact me. Sincerely, /s/ Larry D. Larsen Larry D. Larsen Regulatory Coordinator Email: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3 SHEET 1 OF 8 EXHIBIT 3 The following photographs are attached. Exhibit 1. Back View with Battery 3A 2. Front View with Display and Keypad. 3B 3. Back View (FCC label location). 3C 4. Side view (Right). 3D 5. Side view (Left). 3E 6. Top view (Controls). 3F 7. Antennas 3G Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3A SHEET 2 OF 8 BACK VIEW WITH BATTERY Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3B SHEET 3 OF 8 FRONT VIEW WITH DISPLAY AND KEYPAD Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3C SHEET 4 OF 8 BACK VIEW (FCC LABELS) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3D SHEET 5 OF 8 SIDE VIEW (RIGHT) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3E SHEET 6 OF 8 SIDE VIEW (LEFT) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3F SHEET 7 OF 8 TOP VIEW Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 3G SHEET 8 OF 8 VHF Antenna No. Antenna Type Kit No. Length (cm) 1 VHF Double Helical (136-174 MHz) PMAD4132A 21 2 VHF GPS Helical (136-147 MHz) PMAD4126A 17 3 VHF GPS Helical (147-160 MHz) PMAD4127A 17 4 VHF GPS Helical (160-174 MHz) PMAD4128A 17 5 VHF GPS Stubby (136-147 MHz) PMAD4129A 11 6 VHF GPS Stubby (147-160 MHz) PMAD4130A 11 7 VHF GPS Stubby (160-174 MHz) PMAD4131A 11

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or Sketch X Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure Sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing. FCC IC Label

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 9 SHEET 1 OF 5 EXHIBIT 9 Internal Photographs The following photographs are attached. Exhibit 1. Mainboard without & with Shields (Top). 9A 2. Mainboard without & with Shields (Bottom). 9B 3. Chassis and housing (front side). 9C 4. Chassis and housing (back side). 9D Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 9A SHEET 2 OF 5 RF board without & with Shields (Top) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 9B SHEET 3 OF 5 RF board without & with Shields (Bottom) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 9C SHEET 4 OF 5 Chassis and housing ( front side) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT3089 EXHIBIT 9D SHEET 5 OF 5 Chassis and Housing (back side)

FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 Motorola Solutions EME Form-SAR-Rpt-Rev. 12.01 Page 1 of 65 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn. Bhd. (455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D. (CSC) 11900 Bayan Lepas, Penang, Malaysia. Date of Report: 9/26/2012 Report Revision: O Report ID: SR10806_PMUD3214A Rev O 120926 Responsible Engineer: Veeramani Veerapan (Sr.EME Engineer) Report Author: Veeramani Veerapan (Sr.EME Engineer) Date/s Tested: 08/14/12-09/10/12 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 08/03/12 DUT Description: Full Keypad with GPS & GOB 136-174 MHz, 1W Test TX mode(s): CW (PTT) Max. Power output: 1.26 W Nominal Power: 1.15 W Tx Frequency Bands: 136 – 174 MHz Signaling type: FM Model(s) Tested: PMUD3214A Model(s) Certified: PMUD3214A Serial Number(s): 627TNP0284 Classification: Occupational/Controlled FCC ID: ABZ99FT3089; Rule Part 90 (150.8-173.4 MHz) Results outside FCC bands are not applicable for FCC compliance demonstration. IC: 109AB-99FT3089; (138-144; 148-149.9 and 150.05-174 MHz) * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 10/3/2012 Certification Date: 10/3/2012 Certification No.: L1120902P FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 Motorola Solutions EME Form-SAR-Rpt-Rev. 12.01 Page 2 of 65 Part 1 of 2 1.0 Introduction ................................................................................................................................. 4 2.0 Abbreviations / Definitions ......................................................................................................... 4 3.0 Referenced Standards and Guidelines ........................................................................................ 4 4.0 SAR Limits ................................................................................................................................. 5 5.0 SAR Result Scaling Methodology .............................................................................................. 6 6.0 Description of Device Under Test (DUT) .................................................................................. 6 7.0 Optional Accessories and Test Criteria....................................................................................... 6 7.1 Antennas ......................................................................................................................... 7 7.2 Battery ............................................................................................................................. 7 7.3 Body worn Accessories ................................................................................................... 7 7.4 Audio Accessories .......................................................................................................... 8 8.0 Description of Test System ......................................................................................................... 8 8.1 Descriptions of Robotics/Probes/Readout Electronics ................................................... 9 8.2 Description of Phantom(s) .............................................................................................. 9 8.3 Description of Simulated Tissue ..................................................................................... 9 9.0 Additional Test Equipment ....................................................................................................... 11 10.0 SAR Measurement System Verification ................................................................................... 11 10.1 Equivalent Tissue Test Results ..................................................................................... 11 10.2 System Check Test Results ........................................................................................... 13 11.0 Environmental Test Conditions ................................................................................................ 13 12.0 DUT Test Methodology ............................................................................................................ 14 12.1 Measurements ............................................................................................................... 14 12.2 DUT Configuration(s) ................................................................................................... 14 12.3 DUT Positioning Procedures ........................................................................................ 14 12.3.1 Body…

Text truncated - open the document above for the full version.

FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 1 of 26 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn. Bhd. (455657-H) Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12, S.W.D. (CSC) 11900 Bayan Lepas, Penang, Malaysia. Date of Report: 9/26/2012 Report Revision: O Report ID: SR10806_PMUD3214A Rev O 120926 Responsible Engineer: Veeramani Veerapan (Sr.EME Engineer) Report Author: Veeramani Veerapan (Sr.EME Engineer) Date/s Tested: 08/14/12-09/10/12 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 08/03/12 DUT Description: Full Keypad with GPS & GOB 136-174 MHz, 1W Test TX mode(s): CW (PTT) Max. Power output: 1.26 W Nominal Power: 1.15 W Tx Frequency Bands: 136 – 174 MHz Signaling type: FM Model(s) Tested: PMUD3214A Model(s) Certified: PMUD3214A Serial Number(s): 627TNP0284 Classification: Occupational/Controlled FCC ID: ABZ99FT3089; Rule Part 90 (150.8-173.4 MHz) Results outside FCC bands are not applicable for FCC compliance demonstration. IC: 109AB-99FT3089; (138-144; 148-149.9 and 150.05-174 MHz) * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. Results outside FCC bands are not applicable for FCC compliance demonstration. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 10/3/2012 Certification Date: 10/3/2012 Certification No.: L1120902P FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 2 of 26 APPENDIX D Test System Check Scans FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 3 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 4 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 5 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 6 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 7 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 8 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 9 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 10 of 26 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 11 of 26 APPENDIX E DUT Scans (Shortened Scan and Highest SAR configurations) *Highest SAR found is outside of FCC Part 90 band FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 12 of 26 Shortened Scan Result- Outside FCC Part 90 band Table 21 Shortened scan reflect highest SAR producing configuration; approximate run time is 7 minutes. Representative full scan run time was 26 minutes. “Shortened” scan max calculated SAR using SAR drift: 1-g Avg. = 0.352 mW/g; 10-g Avg. = 0.203 mW/g. Zoom scan max calculated SAR using SAR drift (see part 1 table 17): 1-g Avg. = 0.365 mW/g; 10-g Avg. = 0.208 mW/g. FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 13 of 26 Body - Highest SAR Configuration Result- Outside FCC Part 90 band Table 17 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 14 of 26 Face - Highest SAR Configuration Result-Within FCC Part 90 band Table 19 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 15 of 26 APPENDIX F DUT Scans - FCC Part 90 (150.8-173.4 MHz) FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 16 of 26 Assessments at the Body with Body worn PMLN6086A Table 14 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 17 of 26 Assessments at the Body with Body worn PMLN6097A Table 15 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 18 of 26 Assessments at the body with Body worn PMLN6099A Table 16 FCC ID: ABZ99FT3089/ IC: 109AB-99FT3089 SR 10806 EMS EME Form-SAR-Rpt-Rev. 12.01 Page 19 of 26 Assessment at the Body with other audio accessories Assessment per “KDB 643646 D01 Body SAR Test Consideration for Audio Accessories without Buil…

Text truncated - open the document above for the full version.