ABZ99FT4065AlphaX UHF 4W Portable Radio

Modern, Efficient, With Exceptional Value Business Portable Two-Way Radio A B C D  Attaching and Removing the Antenna To Attach Antenna To Remove Antenna 1.Fasten the antenna to the radio by placing the threaded end of the antenna into the Antenna Connector. 2.Rotate the antenna clockwise until tight. 1.Turn the antenna in a counter-clockwise direction until it dis- engages from the radio. gg Antenna Connector Threaded End of Antenna Attaching and Removing the Battery To Attach Battery To Remove Battery 1.Fit the battery slots with the grooves on the radio. 2.Slide the battery upwards until a click is heard. 1.Slide the battery clasp away from the radio. 2.Slide the battery downwards. 3.Pull the battery away from the radio. Battery Slots Grooves Battery Clasp Attaching and Removing the Belt Clip To Attach Belt Clip To Remove Belt Clip 1.Align mounting rails of the radio with the grooves of the belt clip. 2.Slide the belt clip downwards until it clicks into place. 1.Insert the end of a key between the release tab and the back surface of the radio. 2.Lift the release tab. 3.Slide the belt clip upwards. Release Tab Mounting Grooves Charging your Radio 1.Turn off your radio, if it is turned on. It is highly recom- mended that the radio be turned off while charging. 2.Lift the Dust Cover covering the Accessory Connector. 3.Insert charging connection of the charger into the Programming Port. 4.Plug in charger to wall outlet. 5.Radio should be charged at least 16 hours initially before decreasing charging time to 10 hours. 6.Turn on your radio, when charging is complete; you should see all 3 bars of the Battery Level Indicator illuminated. Programming Port Dust Cover *6881096C35* 6881096C35-O © 2003 by Motorola, Inc. Motorola, Inc. 1301 E. Algonquin Road, Schaumburg IL 60196 Printed in USA. All Rights Reserved. Product Safety and RF Exposure Compliance ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 68P81095C98) to ensure compliance with RF energy exposure limits. A B C D  Scan Scan allows you to monitor multiple channels and receive calls that are transmitted on them. Two types of scan are supported: Normal Scan and Priority Scan. Normal Scan searches all channels sequentially in the radio’s scan list, whereas Priority Scan allocates 50% of the scanning time to the Priority Channel (the first channel in the designated scan list). During scan, when activity is detected that meets the unsquelch condition, the radio stops scanning and switches to that channel; the G indicator is illuminated, and the channel number is displayed. When no activity is detected for a pre-set time, the radio resumes scanning. If your radio has switched to a non-priority channel during priority scan, it still checks for activity on the priority channel. If activity is detected there, the radio switches to the priority channel. The radio transmits on the Home Channel, if PTT is pressed during scanning. If the radio has stopped scanning, and changed to a particular channel, all transmit and receive activity is performed on that channel. • Press the Scan button to begin channel scanning. The G indicator blinks to indicate that the radio is scanning. The LCD Screen shows the Home Channel where the scan began. • Press the button to scan the channels in incremental order, and thebutton to scan in the opposite order. • Press Scan button to stop scanning. Deleting a Nuisance Scan Channel A channel with unwanted activity is called a Nuisance Channel. You can remove a Nuisance Channel from the scan list temporarily. To remove a Nuisance Channel • Press the Nuisance Channel Delete button, when your radio stops on a Nuisance Channel. A high-pitched tone is heard. You cannot remove the Home or Priority Channel from the scan list. If attempted, a low-pitched tone is heard, and no action is taken. To reinstate the deleted channel(s) into the scan list, restart scan, or simply turn off your radio and turn it on again. Programming Mode This mode allows you to change feature parameters to enhance the use of your radio. Entering Programming Mode If your radio is turned on, turn it off. Press and hold the Monitor button, and turn on your radio. A ringing tone is heard, indicating that your radio is in Programming Mode. The K indicator illuminates and RW is displayed. Exiting Programming Mode Turn off the radio, to exit Programming Mode. Accessing Programming Mode Parameters Press PTT or the Monitor button, to scroll through the features available in Programming Mode. Press the button to scroll through the parameters for each feature. FeatureRangeRemarks Squelch Level (SQL-XX) SQL-00, ..., SQL-15Select low level when you need to receive very weak signal, and select high level when the communications distance is near. Time Out Timer (TOT-XXX) TOT-OFF, TOT-001, ..., TOT-010This determines the maximum duration (in minutes) that you can transmit continuously. Battery Saver (BS-XXXX) BS-OFF, BS-NORM, BS-ENH Battery Saver helps to extend your battery life. When enabled, it turns off radio receiver circuitry periodically when no activity is detected. BS-NORM (Normal) turns off the radio less frequently; select this if you want to save bat- tery, but expect a Selective Call. BS-ENH (Enhanced) turns off the receiver for a longer duration; select this if you want to maximize battery saving and do not expect to receive any Selective Call. Battery Type (BT-XXXX) BT-NIMH, BT-NICD, BT-ALK Selects the type of battery that your radio uses: NIMH (Nickel Metal Hydride), NICD (Nickel Cadmium) or ALK (Alkaline). Alert Tone Volume (BEEP-X) BEEP-OFF, BEEP-1, BEEP-2, BEEP-3 Selects the alert tone volume needed. Select BEEP-OFF, if you require quiet operation, or BEEP-3, if working in a noisy environ…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Certification of Data Pursuant to 47 CFR 2.1517(g) The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received a BEEE degree from the University of Technology , Malaysia. 2) I have 5 years experience in developing, testing, and certifying Land Mobile Communications Products. NAME: Sumiyyah Abdul Kader SIGNATURE: SUMIYYAH DATE: December 22, 2003 POSITION: Electrical Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Muhammad Azanor SIGNATURE: AZANOR DATE: December 22, 2003 POSITION: Engineering Manager EXHIBIT 2 SHEET 1 OF 1

FCC ID: ABZ99FT4065 REQUEST FOR CONFIDENTIALITY Date: December 22, 2003 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT4065 Dear Sir or Madam: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d) and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected] EXHIBIT 13B SHEET 1 OF 1

FCC ID: ABZ99FT4065 Date: December 22, 2003 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT4065 Dear Sir or Madam: Motorola Inc., 1309 East Algonquin Road, Schaumburg, Illinois, herein submits application for Certification of the equipment identified by FCC ID number ABZ99FT4065. This transmitter is primarily intended for use in a portable radio application with capabilities for conventional communications with a conducted transmit power which is adjustable from 2 Watt (+33 dBm) to 4.7 Watts (+36.7 dBm). The subject transmitter complies with CFR Title 47, Section 90.203, in that the operator cannot directly program the transmit frequencies using only the normally accessible external controls of the unit. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected] EXHIBIT 13A SHEET 1 OF 1

Applicant: Motorola Inc. FCC ID: ABZ99FT4065 External Photographs Pursuant to 47 CFR 2.1033(c) 12 Figure 3-1: Front view of complete radio. EXHIBIT 3 SHEET 1 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Figure 3-2: Back view of complete radio. EXHIBIT 3 SHEET 2 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Figure 3-3: Right side view of complete radio. EXHIBIT 3 SHEET 3 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Figure 3-4: Left side view of complete radio. EXHIBIT 3 SHEET 4 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 FCC Label Location RF Safety Label Location Figure 3-5: Rear view of complete radio showing FCC Label & RF Safety Label location. EXHIBIT 3 SHEET 5 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Figure 3-6: Close-up of RF Safety Label Stubby Antenna Whip Antenna Figure 3-7: Types of Antenna EXHIBIT 3 SHEET 6 OF 7 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 EXHIBIT 3 SHEET 7 OF 7 Model List Model Number Name Plate Description AAH49RCF8AA1AB - AlphaX 435-480 4W 16ch Black VX

Applicant: Motorola Inc. FCC ID: ABZ99FT4065 IDENTIFICATION LABEL Pursuant to 47 CFR 2.925(a), 2.1033(c), 2.0165 LOCATION A nameplate of the type presented below will be affixed to every transmitter. It will be placed on the bottom of the unit near the front. Shown below is a photo of the actual label affixed to the cast chassis of the transmitter. TYPE The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. EXHIBIT 1 SHEET 1 OF 2 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 EXHIBIT 1 SHEET 2 OF 2 EXHIBIT 1A – GENERAL INFORMATION 1. Application References: TIA/EIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards Code of Federal Regulations Title 47, Part 2, Sec. 2.1033-2.1057, and Part 90, Section 90.210. 2. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commission’s rules. The intended use of this transceiver includes applications covered in the Code of Federal Regulations Title 47, Part 90. Maximum transmitter power shall not be adjustable by the user.

Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Internal Photographs Pursuant to 47 CFR 2.1033(c)12 Figure 9-1: Top Side of RF PCB. Figure 9-2: Bottom Side of RF PCB. EXHIBIT 9 SHEET 1 OF 3 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 Figure 9-3: Top Side of Controller PCB. Figure 9-4: Bottom Side of PCB with shields. EXHIBIT 9 SHEET 2 OF 3 Applicant: Motorola Inc. FCC ID: ABZ99FT4065 EXHIBIT 9 SHEET 3 OF 3 Figure 9-5: Top View of chassis. Figure 9-6: Bottom View of chassis.

MOTOROLA INC. FCC ID: ABZ99FT4065 PARTS LIST AND TUNE UP PROCEDURES (CONFIDENTIALITY REQUESTED) This exhibit contains a list of the semiconductor devices used in the transceiver and the test equipment and tuning procedures for maintaining the transceiver. EXHIBIT 10A Function of RF Semiconductors and Other Active Devices EXHIBIT 10B List of Recommended Test Equipment for Servicing EXHIBIT 10C Tune Up Information EXHIBIT 10 MOTOROLA INC. FCC ID: ABZ99FT4065 Exhibit 10A - Function of RF Semiconductors & Other Active Devices Pursuant to 47 CFR 2.10339(c)(10) REF NO Circuit Application INDUSTRY EQUIVALENT CD501 Discriminator IFD0455C24E03 F402 Filter 45N12A5 (45.1MHz) UM-5J-SMD F501 Filter BLFYM455D F502 Filter ALFYM455G Q201 DC Switch 2SB798-T1 DK Q202 DC Switch UMW1N TL Q203 Protect 1SR154-400 TE25 Q204 DC Regulator XC62HR5002PR Q208 TX/RX Switch RN2102 Q209 TX/RX Switch RN1102 Q210 Save Switch 2SA1362-GR TE85L Q211 RX Save Switch RN2110 Q308 VCO Buffer 2SC5086-Y TE85L Q309 TX/RX VCO Switch 2SJ243-T1 Q310 TX/RX VCO Switch UMC4N TR Q311 RX VCO 1SV228-TPH3 Q314 PLL Loop Filter 2SA1586-GR TE85L Q315 PLL Loop Filter 2SC4116-GR TE85L Q316 PLL Loop Filter UDZ S 7.5B TE-17 Q319 PLL Unlock detect 1SS355 TE-17 Q323 PLL IC MB15A02PFV1-ER Q324 RX VCO 2SC4226-T1 R24 Q325 TX VCO 2SC4226-T1 R24 Q326 TX VCO 1SV228-TPH3 Q329 Modulation 1SV279-TPH3 Q330 DC Filter 2SC4116-GR TE85L Q331 Filter Switch 2SC4116-GR TE85L Q332 DC/DC Rectification RB521S-30 TE61 Q333 DC/DC Converter TK11850LTL Q334 Reference Voltage TAR5S33 Q401 RF BPF Filter 1SV225-TPH3 Q403 RF Protect 1SS362-TE85L Q404 RF Amplifier 2SC5086-Y TE85L Q405 RF BPF Filter 1SV225-TPH3 Q407 Mixer Diode HSMS-2817 (B7) EXHIBIT 10A SHEET 1 OF 3 MOTOROLA INC. FCC ID: ABZ99FT4065 Exhibit 10A - Function of RF Semiconductors & Other Active Devices (cont’d) Q408 1st IF Amplifier 2SC4215-Y TE85L Q409 ANT Switch HVU131TRF Q410 ANT Switch MA4PH262 Q411 TX Filnal Amplifier 2SK3476 Q412 TX Driver Amplifier 2SK3475 Q413 TX Pre-driver 2SC3356-T1B R24 Q414 TX Buffer 2SC5086-Y TE85L Q415 VCO Switch HSC277TRF Q416 RX Local Buffer 2SC5086-Y TE85L Q417 PA Switch RN1102 Q418 PA Switch RN1104 Q419 PA Controle LM2904PW Q501 Discriminator Switch UMC4N TR Q502 RX HPF LM2902DTB Q503 SQ Switch 2SJ144Y-TE85L Q504 N/W Switch RN1104 Q505 RX LPF LM2902DTB Q506 IF IC TA31136FN-TP1 Q507 RX N/W Switch DAN235ETL Q508 RX N/W Switch DAN235ETL Q509 RX N/W Switch RN2104 Q510 RX HPF NJM2107F (TE1) Q511 RX N/W Switch RB521S-30 TE61 Q512 Audio Switch HSC277TRF Q513 Audio Switch RB521S-30 TE61 Q601 TX N/W Switch RN1104 Q602 Mic Amplifier LM2902DTB Q604 Audio Switch RB521S-30 TE61 Q605 N/W Audio Switch RN1104 Q608 N/W Audio Switch RN1104 Q609 Audio Switch UMG2N TR Q610 VOX Amplifier LM2902DTB Q613 DTMF Switch RN2104 Q615 TX Audio Mute 1SS361 Q616 TX Audio Mute SSM3K03FE-TE85L Q617 Sub Audio Amplifier NJM2107F (TE1) Q701 Audio Mute Switch RN1104 Q702 Audio Amplifer TDA8541T/N1 Q703 PTT Switch RN1104 Q704 PTT Switch 2SA1586-GR TE85L EXHIBIT 10A SHEET 2 OF 3 MOTOROLA INC. FCC ID: ABZ99FT4065 Exhibit 10A - Function of RF Semiconductors & Other Active Devices (cont’d) Q705 Battery Protect 1SR154-400 TE25 Q706 Protect UDZ S 6.8B TE-17 Q713 Battery Protect 2SC2859 Q714 Battery Protect 2SC4116-GR TE85L Q715 Battery Protect UDZ S 20B TE-17 RV601 TX Deviaton Adj VG025CHXTB103 RV602 DTMF Deviation VG025CHXTB103 RV603 Sub Audio Dev Adj VG025CHXTB103 X301 Reference TCXO HKE3065B X501 2nd Local Crystal HU-816-106 EXHIBIT 10A SHEET 3 OF 3 MOTOROLA INC. FCC ID: ABZ99FT4065 Exhibit 10B - List of Recommended Test Equipment for Servicing Instrument Recommended Type Application RF Signal Generator * HP 8656B or equivalent Receiver Measurements Modulation Analyzer * HP 8901B or equivalent Frequency and Deviation Measurements Audio Analyzer * HP 8903A or equivalent Receiver Measurements Power Meter * HP 438A or equivalent Transmitter Power Output Power Sensor * HP 8482A or equivalent Transmitter Power Output DC Power Supply 0-20 volts at 15 amps Power Supply Attenuator Pad * 50 Ω, 20 Watts, 30 dB Transmitter Measurements DC Ammeter 30 mA to 20 A Current Drain Measurements Computer IBM PC, PC/XT or PC/AT Radio Alignment IF Test Box DSK001C702 Radio Interface to Test Equipment Programming Cable DSK001C706 From Radio to Computer Test Cable DSK001C704 From Test Box to Radio Battery Eliminator DSK001C705 From Radio to Power Supply * These items can be replaced by a Motorola 2000 Series Communications System Analyzer or equivalent piece of integrated communications test equipment. EXHIBIT 10B SHEET 1 OF 1 MOTOROLA INC. FCC ID: ABZ99FT4065 Exhibit 10C - Tune Up Information Pursuant to 47 CFR 2.10339(c)(9) Only 2 parameters are adjustable, transmit power adjustments is performed by electronic means and modulation limiting is performed by by adjusting the potentiometer. The tuning elements that are used for transmitter adjustment are: Location Type of Element Function Q101 Microprocessor Supplies data to Audio Filter IC, Fractional-N Synthesizer, Temperature Compensated Crystal Oscillator, and Power Control IC for Transmitter Modulation, Frequency and Power Adjustment Q121 Digital to Analog Converter Transmitter Power Adjustment RV601 Potentiometer Modulation Limiting Adjustment For TX power adjustment the value of a particular tuning element is determined by data sent to that tuning element by microprocessor Q101. This data is generated by the microprocessor based on tuning information that is stored in the EEPROM (Electrically Erasable Programmable Read Only Memory). Tuning information is stored in the EEPROM during factory adjustment or by qualified field service facilities, using the attached procedure and recommended test equipment. Tuning Procedure 1. Transmitter Power Adjustment a. Select TX Power tab to open up the TX Power window. b. Press NiMH/NiCD or Alkaline tab to select the type of battery in use. c. Press the button that contains the frequency to be tuned. d. Press PTT ON. This will key up the radio at the frequ…

Text truncated - open the document above for the full version.

English Product Safety and RF Exposure for Portable Two-Way Radios The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. For radios that have been approved as intrinsically safe, read the instructions and information on intrinsic safety on page 9 of this booklet. Compliance with RF Energy Exposure Standards NOTICE: This radio is intended for use in occupational/controlled applications where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use. BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ! C a u t i o n © Motorola, Inc. 2003 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 Printed in U.S.A. 3/03. *6881095C98* 68P81095C98-A 2 English Federal Communication Commission (FCC) Regulations The FCC has established limits for safe exposure to radio frequency (RF) emissions from portable two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before portable two-way radios can be marketed in the U.S. When two-way radios are approved for occupational/ controlled environment exposure limits, the FCC requires users to be fully aware of, and exercise control over, their exposure. Awareness and control of RF exposure can be accomplished by the use of labels, or by education and training through appropriate means, such as information and instructions in user manuals or safety booklets. Your Motorola two-way radio has an RF exposure information label in the battery compartment. This user safety booklet includes useful information about RF exposure and helpful instructions on how to control your RF exposure. Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at usage factors of up to 50% talk–50% listen. In terms of measuring RF energy for compliance with FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty cycle (5% talk–5% listen–90% standby), even though this radio complies with FCC occupational exposure limits at usage factors of up to 50% talk. 3 English Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation – Human Exposure) Standard, 2001 • ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) “additional requirements for SMR, cellular and PCS product certification.” Compliance and Control Guidelines and Operating Instructions for Portable Two-Way Radios To control your exposure and ensure compliance with the occupational/ controlled environment exposure limits, always adhere to the following procedures: • Transmit no more than 50% of the time. To transmit (talk), push the Push- To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time or less is important since the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). 4 English • Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one to two inches (2.5 to 5 centimeters) away from the lips. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. •For body-worn operation, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. All Motorola- approved accessory, antenna, and device combinations comply with FCC occupational/controlled environment RF exposure limits. Exposure information on various accessory, antenna, and device combinations can be found under the “Display Exhibits” section of http://www.fcc.gov/oet/ fccid after searching on the FCC ID number, which can be obtained from the label of your radio. Using non–Motorola-approved accessories may result in exposure levels which exceed the FCC’s occupational/controlled environment RF exposure limits. • If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, ensure the antenna and the radio are kept one inch (2.5 centimeters) from the body when transmitting. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. •Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of non–Motorola-approved antennas, batteries and accessories may exceed FCC RF exposure guidelines. For a list of Motorola- approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://www.motorola.com/cgiss/inde…

Text truncated - open the document above for the full version.

APPLICANT: MOTOROLA INC. FCC ID: ABZ99FT4065 RF EXPOSURE INFORMATION Pursuant 47 CFR 2.1093 In accordance with 47 CFR 2.1093(c) this transmitter has been subjected to routine environmental evaluation for RF exposure and found to be compliant with the limits specified in 47 CFR 2.1093(d) for portable devices, using measurements per methods stated in 47 CFR 2.1093(d)(3). The complete S.A.R. EME Compliance Test Report is attached as Exhibit 11B. EXHIBIT 11A SHEET 1 OF 1

Form-SAR-Rpt-Rev. 1.00 Page 1 of 21 CGISS EME Test Laboratory 8000 West Sunrise Blvd Fort Lauderdale, FL. 33322 S.A.R. EME Compliance Test Report Part 1 of 3 Note: Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with all applicable national and international reference standards and guidelines. Deanna Zakharia Signature on File 11/24/03 ____________________________________________________________ _________________________ Ken Enger Date Approved Senior Resource Manager, Product Safety and EME Director, Phone: 954-723-6299 Note: Consistent with the ISO/IEC 17025 recommendation this report shall not be reproduced in part without written approval from an officially designated representative of the Motorola EME Laboratory. Date of Report: November 24, 2003 Report Revision: Rev. O Manufacturer: Motorola Product Description: Portable 435-480 MHz, 4W, 32 CH w/ display/Limited Keypad FCC ID: ABZ99FT4065 Device Model: PMUE2138A Certificate Number: 1449-02 Test Period: 11/17/03 – 11/20/03 EME Technician: Clint Miller Responsible Engineer: Kim Uong (Sr. EME Engineer) Author: Kim Uong (Sr. EME Engineer) Review By: Michael Sailsman Global EME Regulatory Affairs Liaison Form-SAR-Rpt-Rev. 1.00 Page 2 of 21 TABLE OF CONTENTS Part 1 of 3 1.0 Introduction 2.0 Reference Standards and Guidelines 3.0 Description of Test Sample 3.1 Test Signal 3.2 Test Output Power 4.0 Description of Test Equipment 4.1 Description of S.A.R Measurement System 4.2 Description of Phantom 4.2.1 Flat Phantom 4.2.2 SAM phantom 4.3 Simulated Tissue Properties 4.3.1 Type of Simulated Tissue 4.3.2 Simulated Tissue Composition 4.4 Test condition 5.0 Description of Test Procedure 5.1 Device Test Positions 5.1.1 Body 5.1.2 Head 5.1.3 Face 5.2 Test Position Photographs 5.3 Probe Scan Procedures 6.0 Measurement Uncertainty 7.0 S.A.R. Test Results 7.1 S.A.R. results 7.2 Peak S.A.R. location 7.3 Highest S.A.R. results calculation methodology 8.0 Conclusion Part 2 of 3 Appendix A: Power Slump Data/Shortened scan Appendix B: Data Results Appendix C: Dipole System Performance Check Results Part 3 of 3 Appendix D: Calibration Certificates Appendix E: Illustration of Body-worn Accessories Appendix F: Accessories and options test status and separation distances Form-SAR-Rpt-Rev. 1.00 Page 3 of 21 REVISION HISTORY Date Revision Comments 11/24/03 O Release of Pilot results Form-SAR-Rpt-Rev. 1.00 Page 4 of 21 1.0 Introduction This report details the utilization, test setup, test equipment, and updated test results of the Specific Absorption Rate (S.A.R.) measurements performed at the CGISS EME Test Lab for model number PMUE2138A, FCC ID: ABZ99FT4065. The applicable exposure environment is Occupational/Controlled. 2.0 Reference Standards and Guidelines This product is designed to comply with the following national and international standards and guidelines. • United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J • IEEE 1528, 2003 "Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques," • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 • Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 • Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Terminal frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 • Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard 2003 • ANATEL, Brazil Regulatory Authority, Resolution 256 (April 11, 2001) "additional requirements for SMR, cellular and PCS product certification." Form-SAR-Rpt-Rev. 1.00 Page 5 of 21 3.0 Description of Test Sample The portable handheld transceiver, FCC ID: ABZ99FT4065, operates using Frequency Modulation (FM) incorporating traditional simplex two-way radio transmission protocol. The intended operating positions are “at the face” with the DUT 1 to 2 inches from the mouth, and “at the body” by means of the offered body-worn accessories. Audio and PTT operation while the radio is at the body is accomplished by means of optional remote accessories that connect to the radio. This device will be marketed to and used by employees solely for work-related operations, such as public safety agencies, e.g. police, fire and emergency medical. User training is the responsibility of these agencies, which can be expected to employ the usage instructions, safety information and operational cautions set forth in the user's manual, instructional sessions or other means. Motorola also makes available to its customers training classes on the proper use of two-way radios and wireless data devices. FCC ID: ABZ99FT4065 is capable of operating in the 435 - 480 MHz band. The rated power is 4 watts with a maximum output capability of 4.7 watts as defined by the upper limit of the production line final test station. Form-SAR-Rpt-Rev. 1.00 Page 6 of 21 FCC ID: ABZ99FT4065 is offered with the following options and accessories: Antenna PMAE4011A Helical 435-480 MHz antenna; -10dBd PMAE4003A Helical 430-470 MHz antenna; -12dBd NAE6483A Whip 403-520 MHz antenna; -4dBd Batteries PMNN4046A Std. NiMH battery Body-worn Accessories 4285820Z01 Shoulder Strap HLN9844A Belt Clip (1.5” belt width) PMLN4467A Carry case, Soft Leather Black PMLN4468A Carry Holster Case, Neoprene Grey PMLN4469A Carry Holster Case, Neoprene Blue RLN4815A Fanny Pack Carry Accessory HLN9985B Waterproof Bag Audio attachments PMLN4294C Ear Set Mic w/PTT PMLN4425A Ear set Boom Mic w/ remote ring PTT HMN9030A Remote Sp…

Text truncated - open the document above for the full version.