ABZ99FT4085UHF Range 2 Mobile Radio w/GPS & BT

M MOTOTRBO XPR TM 5550 Color Display Mobile User Guide 68009504001-A Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: XPR 5550 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. Contents English iii ContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR Series Digital Mobile Radios.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . ix Product Safety and RF Exposure Compliance . . .ix Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . ixComputer Software Copyrights . . . . . . . . . . . . . . . . x Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This User Guide . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 2Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 2 Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 3 Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 4 Assignable Radio Functions . . . . . . . . . . . . . . . . . 4Assignable Settings or Utility Functions . . . . . . . . . 6 Accessing the Programmed Functions . . . . . . . . . . . 6Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . 7 Using the Volume/Channel Knob . . . . . . . . . . . . . . . 7Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Identifying Status Indicators . . . . . . . . . . . . . . . . . . . 9 Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Advanced Menu Icons . . . . . . . . . . . . . . . . . . . . . . 11Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Bluetooth Device Icons . . . . . . . . . . . . . . . . . . . . . . 13LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Receiving and Making Calls . . . . . . . . . . . . . . . . . . 15 Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Selecting a Radio Channel, Su bscriber Alias or ID, or Group Alias or ID . . . . . . . . . . . . . . . . . . . . . . . . . . 16Receiving and Responding to a Radio Call . . . . . . 17 Receiving and Responding to a Group Call . . . . . 17Receiving and Responding to a Private Call . . . 18 Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 19Receiving and Responding to a Selective Call . . 19 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 20 Contents English iv Making a Call with the Volume/Channel Knob . . 21 Making a Group Call . . . . . . . . . . . . . . . . . . . . 21Making a Private Call . . . . . . . . . . . . . . . . . . . 22Making an All Call . . . . . . . . . . . . . . . . . . . . . . 22Making a Selective Call . . . . . . . . . . . . . . . . . . 23 Making a Call with the Scroll Up and Scroll Down Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Making a Call with the Cha nnel Up and Channel Down Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Making a Group or Private Call with the One Touch Access Button . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 25Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . . . 26 Advanced Features . . . . . .…

Text truncated - open the document above for the full version.

Date: September 24, 2012 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Letter of Authorization for FCC ID ABZ99FT4085 Dear Sir or Madam: This letter is to authorize Larry D. Larsen to sign Form 731 applications on my behalf for the subject FCC ID Filing. Please contact me if there are any questions or issues. Sincerely, Ken Weiss Senior Staff Engineer Tel: (847)-576-2789 Fax: (847)-538-3905 E-mail: [email protected]

MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 1 OF 5 GENERAL VIEW, 1000 CHANNEL MODEL WITH MICROPHONE (CLOSE-UP OF RF EXPOSURE LABEL ON FOLLOWING PAGE) MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 2 OF 5 RF EXPOSURE LABEL (CLOSE-UP VIEW) MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 3 OF 5 FRONT VIEW, 1000 CHANNEL MODEL FRONT VIEW, 32 CHANNEL MODEL MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 4 OF 5 BOTTOM VIEW, SHOWING FCC ID LABEL (CLOSE-UP OF FCC ID LABEL ON FOLLOWING PAGE) MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 5 OF 5 CLOSE-UP VIEW OF FCC ID LABEL

MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 1 SHEET 1 OF 2 IDENTIFICATION LABEL Pursuant to 47 CFR 2.1033(c) LOCATION A nameplate of the type presented below will be affixed to every transmitter. It will be placed on the bottom of the unit near the front. Shown below is a photo of the actual label affixed to the cast chassis of the transmitter. TYPE The label is a paper polyester film laminated with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 40 oz/inch. MARKINGS (TEXT) See the Attached Photograph and Exhibit 3, Sheet 4 for the actual location of the FCC label on the device MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 1A SHEET 1 OF 1 GENERAL INFORMATION 1. Production Plans – Pursuant 2.1033 (c) Quantity production is planned. 2. Application References: “Code of Federal Regulations”, Ti tle 47, Part 2, 15, and 90 3. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commissions’ rules.

MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 1 OF 5 TOP VIEW WITH CHASSIS TOP COVER REMOVED (MATING SURFACES OF TOP COVER AND CIRCUIT BOARD IN CHASSIS ARE SHOWN) MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 2 OF 5 TOP VIEW WITH CIRCUIT BOARD REMOVED FROM CHASSIS (MATING SURFACES OF CIRCUIT BOARD AND CHASSIS ARE SHOWN) MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 3 OF 5 FRONT VIEW WITH BLUETOOTH/GPS BOARD INSTALLED ON THE LEFT AND GENERIC OPTION BOARD INSTALLED ON THE RIGHT MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 4 OF 5 FRONT VIEW OF GENERIC OPTION BOARD BACK VIEW OF GENERIC OPTION BOARD MOTOROLA SOLUTIONS, INC FCC ID: ABZ99FT4085 EXHIBIT 3 SHEET 5 OF 5 FRONT VIEW OF BLUETOOTH/GPS BOARD BACK VIEW OF BLUETOOTH/GPS BOARD

Calculation to determine whether the power density could exceed the MPE (1) Where S is the power density at distance d away from an antenna with total output power P t , gain G t and cable loss L. The total power P t equals the maximum output power, P m , scaled by the maximum duty cycle of the signal, c . The factor F is a multiplier to provide a worst-case prediction of power density according to the FCC [1]. See "Justification" worksheet f or details. Product DescriptionDate 4/13/2011 Model numberModel descriptionInput variablesMaximum output power, P m 0.01 W Enter the maximum output power of the device under normal operating temperature & humidity condition s Duty cycle, c 29.30% Enter the duty cycle of the signal (e.g., 100% for CW or CDMA, 12.5% for GSM) frequency f 2450 MHz Enter the lowest (highest) frequency of the transmit band for devices operating above (below) 30 MHz A conservative formulation is used in this worksheet to estimate the power density at a certain distance from a product. The p ower density is compared with the Maximum Permissible Exposure (MPE) given in [1] or [2] to estimate whether the MPE is met. If so, the product is deemed to be compliant with the relevant EME guidelines [1, 2]. If not, MPE testing or SAR testing is necessary to demonstrate EME compliance. Note that EME compliance al one is insufficient to determine total compliance of a product. For example, the FCC also limits the effective (isotropic) radiated power (ERP / EIRP). This worksheet makes use of the free-space formula for power density [1]: PMUE3649AUHF Range 1, 403-470 MHz, 25-40W, radio with internal GPS and Bluetooth using a F L d G cP F L d G P S t m t t 2 2 4 4 π π = = frequency , f 2450 MHz Enter the lowest (highest) frequency of the transmit band , for devices operating above (below) 30 MHz. Antenna gain, G t 5.45 dBi dBi is dB relative to an ideal isotropic source. If antenna gain is given in dBd, add 2.15 to put it in dBi. Cable loss, L 0 dB Enter the loss of the cable connecting the transmitter to the antenna (0 dB if no cable loss information available). Distance, d 20 cm Enter the distance from the antenna Enhancement factor, F 2.56 Choose the enhancement factor: 1 for desktop devices 2.56 for all other devices Output variablesRadiated power density, S 0.005234 mW/cm 2 controlled uncontrolled occupational gen. public MPE (mW/cm 2 ) 5.00 1.00 5.00 1.00 Power density exceeds MPE? NO NO NO NO CommentsReferencesFCD-0989 MPE Calculator Workbook Rev. 4MPE limits are the same across 2.4-2.48GHz (BT band).SR9230[2] ICNIRP, “International Commission on Non-Ionizing Radiation Protection guidelines for limiting exposure to time-varying ele ctric, magnetic and electromagnetic fields (Up to 300 GHz),” Health Physics, vol. 74, no. 4, pp. 494–522, 1998.[1] FCC Office of Engineering and Technology, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency E lectromagnetic Fields," OE T Bulletin 65, Edition 97-01, 1997. FCC [1] ICNIRP [2] F L d G cP F L d G P S t m t t 2 2 4 4 π π = =

Engineering Test Report No. 1100467-01 Measurement of RF Emissions from a Model XPR5550 Bluetooth Transceiver For Motorola, Inc. 1301 E. Algonquin Road Schaumburg, IL 60196 P.O. Number NP5306825 Date Tested March 7 through 16, 2011 Test Personnel Richard King Test Specification FCC "Code of Federal Regulations" Title 47, Part 15, Subpart C, Sections 15.247 for Frequency Hopping Spread Spectrum Intentional Radiators Operating within the band 2400-2483.5MHz Industry Canada RSS-GEN Industry Canada RSS-210 Test Report By: Richard King EMC Engineer Requested By: Larry Larsen Motorola, Inc. Approved By: Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1100467-01 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 75 1 Introduction ................................................................................................................................................... 5 1.1 Scope of Tests ..................................................................................................................................... 5 1.2 Purpose ............................................................................................................................................... 5 1.3 Deviations, Additions and Exclusions .................................................................................................. 5 1.4 EMC Laboratory Identification ............................................................................................................. 5 1.5 Laboratory Conditions.......................................................................................................................... 5 2 Applicable Documents .................................................................................................................................. 5 3 EUT Setup and Operation ............................................................................................................................ 6 3.1 General Description ............................................................................................................................. 6 3.1.1 Power Input ..................................................................................................................................... 6 3.1.2 Peripheral Equipment ...................................................................................................................... 6 3.1.3 Signal Input/Output Leads ............................................................................................................... 6 3.1.4 Grounding ........................................................................................................................................ 6 3.2 Operational Mode ................................................................................................................................ 6 3.3 EUT Modifications ................................................................................................................................ 6 4 Test Facility and Test Instrumentation ......................................................................................................... 6 4.1 Shielded Enclosure .............................................................................................................................. 6 4.2 Test Instrumentation ............................................................................................................................ 6 4.3 Calibration Traceability ........................................................................................................................ 6 4.4 Measurement Uncertainty ................................................................................................................... 7 5 Test Procedures ........................................................................................................................................... 7 5.1 Receiver ............................................................................................................................................... 7 5.1.1 Radiated Measurements ................................................................................................................. 7 5.1.1.1 Requirements ......................................................................................................................... 7 5.1.1.2 Procedures ............................................................................................................................. 8 5.1.1.3 Results .................................................................................................................................... 8 5.2 Transmitter ........................................................................................................................................... 9 5.2.1 20dB Bandwidth .............................................................................................................................. 9 5.2.1.1 Requirement ........................................................................................................................... 9 5.2.1.2 Procedures ............................................................................................................................. 9 5.2.1.3 Results .................................................................................................................................... 9 5.2.2 Carrier Frequency Separation ......................................................................................................... 9 5.2.2.1 Requirements ........................................................................................…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1100467-01 Page 20 of 75 Figure 2 Test Setup for Radiated Emissions, above 1GHz – Horizontal Polarization Test Setup for Radiated Emissions, above 1GHz – Vertical Polarization