ABZ99FT4089PORTABLE UHF RADIO

m XPR TM 3000 Series Quick Reference Guide and Safety Manual 1 English Regulatory Compliance and Product Safety for Portable Two-Way Radios BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRINSIC SAFETY ON PAGE 12 OF THIS BOOKLET. C a u t i o n 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE:This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific 3 English operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/ index.htm l Federal Communication Commission (FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two- way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. 4 English This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/ controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. • FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 • Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. 5 English RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. Guidelines: • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • DO NOT use this device if the operational requirements described herein are not met. Operating Instructions • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To- Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Two-Way Radio Operation • Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips. Antenna should be kept away from the eye. Keeping…

Text truncated - open the document above for the full version.

PROFESSIONAL DIGITAL TWO-WAY RADIO MOTOTRBO™ XPR™ 3500 LIMITED KEYPAD PORTABLE USER GUIDE Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product:Model Name: XPR 3500 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this dev ice complies with Part 15 of the FCC Ru les. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the fo llowing two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NAG-LACR.book Page i Thursday, April 12, 2012 5:58 PM Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. NAG-LACR.book Page ii Thursday, April 12, 2012 5:58 PM English iii ContentsThis User Guide contains all information you need to use the MOTOTRBO XPR 3500 Digital Portable Radio.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . vii Product Safety and RF Exposure Compliance . . vii Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . viiComputer Software Copyrights . . . . . . . . . . . . . . viii Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . ix How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Univer sal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attaching the Accessory Connector . . . . . . . . . . . . . 4Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 6Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 8 Assignable Radio Functions . . . . . . . . . . . . . . . . . 8Assignable Settings or Utility Functions . . . . . . . . . 9 Accessing the Programmed Functions . . . . . . . . . . 10Push-To-Talk (PTT) Bu tton . . . . . . . . . . . . . . . . . . . 10 Switching Between Conventional Analog and Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Linked Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . 13Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Advanced Menu Icons . . . . . . . . . . . . . . . . . . . . . . 15 Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . 16LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . 19Receiving and Responding to a Radio Call . . . . . . 19 Receiving and Responding to a Group Call . . . . . 20Receiving and Responding to a Private Call . . . 21 Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 22Receiving and Responding to a Selective Call . . 22 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 23 Making a Call with the Chan nel Selector Knob . . 24 NAG-LACR.book Page iii Thursday, April 12, 2012 5:58 PM English iv Making a Selective Call . . . . . . . . . . . . . . . . . . . 26 Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 27Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 28 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 28Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 28 Radio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Sending a Radio Check . . . . . . . . . . . . . . . . . . . 29 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Viewing a…

Text truncated - open the document above for the full version.

English 10 Accessing the Programmed Functions You can access various radio functions through one of the following ways:• A short or long press of the relevant programmable buttons. OR • Use the Menu Navigation Buttons as follows: 1 To access the menu, press the c button. Press the appropriate Menu Scroll button ( < or > ) to access the menu functions. 2 To select a function or enter a sub-menu, press the e button. 3 To go back one menu level, or to return to the previous screen, press the d button. Long press the d button to return to the Home screen. NOTE: Your radio automatically exits the menu after a period of inactivity and returns to your Home screen. Push-To-Talk (PTT) Button The PTT button on the side of the radio serves two basic purposes:• While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.Press and hold down PTT button to talk. Release the PTT button to listen.The microphone is activated when the PTT button is pressed. < c e > d PTT Button NAG-LACR.book Page 10 Thursday, April 12, 2012 5:58 PM English 11 • While a call is not in progress, the PTT button is used to make a new call (see Making a Radio Call on page 23). If the Talk Permit Tone (see Turning the Talk Permit Tone On or Off on page 61) or the PTT Sidetone is enabled, wait until the short alert tone ends before talking. During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you will hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond.You will also hear a continuous talk prohibit tone, if your call is interrupted, indicating that you should release the PTT button, for example when the radio receives an Emergency Call. Switching Between Conventional Analog and Digital Mode Each channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Selector Knob to switch between an analog or a digital channel.When switching from digital to analog mode, certain features are unavailable. Icons for t he digital features (such as Messages) reflect this change by appearing ‘grayed out’. Disabled features are hidden in the menu.Your radio also has features available in both analog and digital mode. However, the minor differ ences in the way each feature works does NOT affect the performance of your radio. Your radio also switches between digital and analog modes during a dual mode scan (see Scan on page 32). Channel Selector Knob NAG-LACR.book Page 11 Thursday, April 12, 2012 5:58 PM English 12 IP Site Connect This feature allows your radio to extend conventional communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network.When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmission s. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the repeater with the strongest Received Signal Strength Indi cator (RSSI) value. In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it.NOTE: Each channel can only have either Scan or Roam enabled, not both at the same time. Channels with this feature enabled can be added to a particular roam list. The radio searches the channel(s) in the Members roam list during the automatic r oam operation to locate the best site.A roam list supports a maximum of 16 channels (including the Selected Channel). You cannot manually add or delete an entry to the roam list. A Software License Key sold separately is required to use this feature Check with your dealer or system administrator for more information. Capacity Plus Capacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which us es a pool of channels to support hundreds of users and up to 254 Groups. This feature allows your radio to efficiently utilize the available number of programmed channels while in Repeater Mode.Icons of features not applicable to Capacity Plus are not available in the menu. You hear a negative indicator tone if you try to access a featur e not applicable to Capacity Plus via a programmable button press.Your radio also has features that are available in conventional digital mode, and Capacity Plus. However, the minor differences in the way each feature works does NOT affect the performance of your radio. A Software License Key sold separately is required to use this feature.Check with your dealer or system administrator for more information on this configuration. NAG-LACR.book Page 12 Thursday, April 12, 2012 5:58 PM English 13 Linked Capacity Plus Linked Capacity Plus is a multi-site multi-channel trunking configuration of the MOTOTRBO radio system, combining the best of both Capacity Plus and IP Site Connect configurations.Linked Capacity Plus allows your radio to extend trunking communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network. It also provides an increase in capacity by efficiently utilizing the combined available number of programmed channels supported by each of the available sites. When the radio moves out of range from one site and into the range of another, it connects to the new site's repeater to send or receive calls/data transmission s. Depending on your settings, this is done automatically or manually.If the radio is set to do this automatically, it scans through all available sites when the signal fro…

Text truncated - open the document above for the full version.

Date: March 29, 2012 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Letter of Authorization for FCC ID ABZ99FT4089 Dear Sir or Madam: This letter is to authorize Larry D. Larsen to sign Form 731 applications on my behalf for the subject FCC ID Filing. Please contact me if there are any questions or issues. Sincerely, Ken Weiss Senior Staff Engineer Tel: (847)‐576‐2789 Fax: (847)‐538‐3905 E‐mail: [email protected]

Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 1 OF 12 EXHIBIT 3 EXTERNAL PHOTOGRAPHS - Pursuant to 47 CFR 2.1033(c) 12 The following photographs are attached. 3-1. Front view (without antenna) 3-2. Front view (with Antenna) 3-3. Back view with battery 3-4. Back view without battery FCC label location 3-5. FCC label (Close view) 3-6. RF exposure label (Close view) 3-7. Bottom view 3-8. Side View (Left) PTT button side 3-9. Side View (right) side connector side 3-10. Top view With Antenna 3-11. Top view Without Antenna 3-12. Type of batteries 3-13. Type of Antenna (4 color code for 4 different frequency ranges) Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 2 OF 12 Figure 3-1: Front view of Full display and keypad model Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 3 OF 12 FIGURE 3- 2: Front View Antenna Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 4 OF 12 FIGURE 3- 3: Back View with Battery Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 5 OF 12 FIGURE 3-4: MODEL, FCC AND SAFETY LABELS LOCATION FCC Label Location Model Label Location Safety Label Location Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 6 OF 12 FIGURE 3-5: CLOSE UP VIEW OF FCC LABEL. FIGURE 3-6: CLOSE UP VIEW OF THE SAFETY LABEL. Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 7 OF 12 FIGURE 3- 7: Bottom View with Battery Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 8 OF 12 FIGURE 3-8: RIGHT SIDE VIEW (PTT) Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 9 OF 12 FIGURE 3-9: LEFT SIDE VIEW (UC) Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 10 OF 12 FIGURE 3-10: Top View with Antenna FIGURE 3-11: Top View without Antenna Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 11 OF 12 FIGURE 3-12: Types of Batteries NO KIT NUMBER BATTERY TYPE 1. PMNN4416A Batt Std Ip56 Liion1500m1600t 2. PMNN4407A IMPRES Li-ion Slim Battery (1500mAH) 3. PMNN4409A IMPRES Hi-Cap Li-ion Non-FM Battery (2150 mAH) 4. PMNN4415A Batt Std Ip56 Nimh1300m1400t 1 3 4 2 Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 3 SHEET 12 OF 12 FIGURE 3-13: TYPES OF ANTENNAS NO ATTENNA TYPE COLOUR LENGTH 1. UHF stubby antenna (440 – 490 MHz) Green 9 cm 2. UHF stubby antenna (470 – 527 MHz) White 9 cm 3. UHF stubby antenna (403 – 450 MHz) Red 9 cm 4. UHF whip antenna (403 – 527 MHz) Orange 15 cm 2 1 4 3

Applicant: Motorola Solutions Inc FCC ID: ABZ99FT4089 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION See the Attached Photograph or Sketch Top of Radio X Back of Radio under Belt Clip Back of Radio TYPE X sensitive adhesive backing. The adhesive is a permanent type acrylic The label is a polyester film laminate with a pressure with the minimum peel strength of 32 oz/inch. MARKINGS (TEXT) X location of the FCC label on the device. See the Attached Photograph and Exhibit 3-5 for the actual Label Attached Below. See Attached Drawing.

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 1 OF 7 Internal Photographs The following photographs are attached. Exhibit 1. MOTOTRBO UHF complete internal open up view 9A 2. MOTOTRBO UHF Chassis and RF Board 9B 3. MOTOTRBO UHF RF Board with shields (Top) 9C 4. MOTOTRBO UHF RF Board without shield (Top) 9D 5. MOTOTRBO UHF RF Board with shield (Bottom) 9E 6. MOTOTRBO UHF RF Board without shield (Bottom) 9F Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 2 OF 7 Exhibits 9A MOTOTRBO UHF complete internal open up view Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 3 OF 7 Exhibit 9B MOTOTRBO UHF Chassis and RF Board Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 4 OF 7 Exhibit 9C MOTOTRBO UHF RF Board with shields (Top) RF Port (for conducted measurement) Antenna port Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 5 OF 7 Exhibit 9D MOTOTRBO UHF RF Board without shield (Top) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 6 OF 7 Exhibit 9E MOTOTRBO UHF RF Board with shield (Bottom) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT4089 EXHIBIT 9 SHEET 7 OF 7 Exhibit 9F MOTOTRBO UHF RF Board without shield (Bottom)

SR9695 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 1 of 62 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 01/03/12 Report Revision: O Report ID: SAR rpt_PMUE3838A_Rev.O 120103_SR9695 Responsible Engineer: Veeramani Veerapan (Senior EME Engineer) Report Author: Veeramani Veerapan (Senior EME Engineer) Date/s Tested: 8/05/11-10/04/11; 12/28/11; 01/20/2012 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 7/08/11 DUT Description: 403-527 MHz 4W NKP Test TX mode(s): CW (PTT) Max. Power output: 4.8 W Nominal Power: 4.0 W Tx Frequency Bands: 403-527 MHz Signaling type: FM Model(s) Tested: PMUE3838A Model(s) Certified: PMUE3838A Serial Number(s): 446TMM0025, 446TMM0023 Classification: Occupational/Controlled FCC ID: ABZ99FT4089; Rule part 90 (406.1-512 MHz) IC: 109AB-99FT4089; (406.1-430 and 450-470 MHz) * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 1/30/2012 Certification Date: 1/30/2012 Certification No.: L1120112P SR9695 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 2 of 62 Part 1 of 2 1.0 Introduction ..............................................................................................................4 2.0 Abbreviations / Definitions ......................................................................................4 3.0 Referenced Standards and Guidelines .....................................................................4 4.0 SAR Limits ..............................................................................................................5 5.0 SAR Result Scaling Methodology ...........................................................................6 6.0 Description of Device Under Test (DUT) ...............................................................6 7.0 Optional Accessories and Test Criteria ...................................................................6 7.1 Antennas ......................................................................................................6 7.2 Batteries .......................................................................................................7 7.3 Body worn Accessories ...............................................................................7 7.4 Audio Accessories .......................................................................................8 8.0 Description of Test System ......................................................................................9 8.1 Descriptions of Robotics/Probes/Readout Electronics ................................9 8.2 Description of Phantom(s) ...........................................................................9 8.2.1 Dual Flat Phantom ...........................................................................9 8.2.2 SAM Phantom ..................................................................................9 8.2.3 Elliptical Phantom ............................................................................9 8.3 Description of Simulated Tissue ................................................................10 9.0 Additional Test Equipment ....................................................................................11 10.0 SAR Measurement System Verification ................................................................11 10.1 Equivalent Tissue Test Results ..................................................................12 10.2 System Check Test Results ........................................................................14 11.0 Environmental Test Conditions .............................................................................15 12.0 DUT Test Methodology .........................................................................................15 12.1 Measurements ............................................................................................15 12.2 DUT Configuration(s) ................................................................................15 12.3 DUT Positioning Procedures ....................................................................15 12.3.1 Body ............................................................................................16 12.3.2 Head ............................................................................................16 12.3.3 Face .............................................................................................16 12.4 DUT Test Ch…

Text truncated - open the document above for the full version.

SR9695 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 1 of 59 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 12/20/11 Report Revision: O Report ID: SAR rpt_PMUE3838A_Rev.O 111220_SR9695 Responsible Engineer: Veeramani Veerapan (Senior EME Engineer) Report Author: Veeramani Veerapan (Senior EME Engineer) Date/s Tested: 8/05/11-10/04/11; 12/28/11; 01/20/2012 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 7/08/11 DUT Description: 403-527 MHz 4W NKP Test TX mode(s): CW (PTT) Max. Power output: 4.8 W Nominal Power: 4.0 W Tx Frequency Bands: 403-527 MHz Signaling type: FM Model(s) Tested: PMUE3838A Model(s) Certified: PMUE3838A Serial Number(s): 446TMM0025, 446TMM0023 Classification: Occupational/Controlled FCC ID: ABZ99FT4089; Rule part 90 (406.1-512 MHz) IC: 109AB-99FT4089; (406.1-430 and 450-470 MHz) * Refer to section 15 of part …

Text truncated - open the document above for the full version.