ABZ99FT4096BNon Broadcast Transmitter

EXHIBIT D User Information User Information Tune-up and user / operational manual information are provided in the following exhibits. EXHIBIT DESCRIPTION D1 Tune-Up Procedure D2 User / Operational Manual APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT3094B 109AB-99FT3094B EXHIBIT D2 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT3094B 109AB-99FT3094B User / Operational Manual Operational or User’s Manual The manual should include instruction, installation, operator, or technical manuals with required ‘information to the users’. This manual should include a statement that cautions the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manual shall include RF Hazard warning statements, if applicable. The end user in the US and Canada receives a booklet entitled “MOTOTRBO™ SLR 5000 Series Repeater Quick Start Guide” (part number MN001440A01-AB, January 2023 , as all units are shipped with this document. This booklet is printed in English and French Canadian. As indicated in the ‘Quick Start Guide’, more detail can be found in the document “MOTOTRBO™ SLR 5000 Series Repeater Basic Service and Installation Manual” (part number MN001436A01-AJ, April 2020). Upon request, published basic service and installation manuals will be sent to the commission and/or telecommunication certification body (TCB). All of the descriptions, block diagrams, and schematics that are included in this filing package are current as of the package submittal date. MOTOTRBO ™ SLR 5000 Series Repeater Quick Start Guide January 2023 © 2022 Motorola Solutions, Inc. All rights reserved MN001440A01 MN001440A01-AB Notations Used in This Manual Note and caution notations are used throughout the text in this publication. These notations are used to emphasize that safety hazards exist, and due care must be taken and observed. Caution: Indicates a potentially hazardous situation which, if not avoided, might result in equipment damage. Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or injury. : Indicates areas of the product that pose potential burn hazards. General Safety and Installation Standards and Guidelines Warning: For safe installation, operation, service and repair of this equipment, follow the safety precautions and instructions described below, as well as any additional safety information in the Motorola Solutions product service and installation manuals and the Motorola Solutions R56 Standards and Guidelines for Communications Sites manual (which can be obtained by ordering CD-ROM 9880384V83). To obtain copies of these materials, contact Motorola Solutions as directed at the end of this section. After installation, these instructions should be retained and readily available for any person operating or servicing this repeater or working near it. Failure to follow these safety precautions and instructions could result in serious injury or property damage. The installation process requires preparation and knowledge of the site before the installation begins. Review installation procedures and precautions in the Motorola Solutions R56 manual before performing any site or component installation. Personnel must use safe work practices and good judgment, and always follow applicable safety procedures, such as requirements of the Occupational Safety and Health Administration (OSHA), the National Electrical Code (NEC), and local codes. The following are additional general safety precautions that must be observed: • To continue compliance with any applicable regulations and maintain the safety of this equipment, do not install substitute parts or perform any unauthorized modifications. • All equipment must be serviced by Motorola Solutions trained personnel. • If troubleshooting the equipment while the power is on, be aware of live circuits which could contain hazardous voltage. • Do not operate the radio transmitters unless all RF connectors are secure and all connectors are properly terminated. • All equipment must be properly grounded in accordance with the Motorola Solutions R56 and specified installation instructions for safe operation. • Slots and openings in the cabinet are provided for ventilation. Do not block or cover openings that protect the devices from overheating. • Some equipment components can become extremely hot during operation. Turn off all power to the equipment and wait until sufficiently cool before touching. • Maintain emergency first aid kits at the site. • Never store combustible materials in or near equipment racks. The combination of combustible material, heat and electrical energy increases the risk of a fire hazard. • Equipment should be installed in a site that meets the requirements of a “restricted access location,” per (UL60950-1, UL62368 & EN62368), which is defined as follows: “Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken; and access is through the use of a tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.” English 1 • Burn hazard. The metal housing of the product may become extremely hot. Use caution when working around the equipment. • RF energy burn hazard. Disconnect power in the cabinet to prevent injury before disconnecting and connecting antennas. • Shock hazard. The outer shields of all Tx and Rx RF cables outer shields must be grounded per the Motorola Solutions R56 manual. • Shock hazard. DC input voltage should be no higher than 60 VDC. This maximum voltage should include consideration of the battery charging “float voltage” associated with the intended supply system, regardless of the marked power rating of the equipment. • All Tx and Rx RF cables should be connected to a surge protection device accordin…

Text truncated - open the document above for the full version.

TO: Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd Columbia, MD 21046 ATTENTION: Federal Communication Commission Equipment Authorization To whom it may concern, We would like to submit for Certification to FCC: ABZ99FT4096B. Please find in the following application all related documentation to support this New Single Certification. We would appreciate your prompt attention to the submittal. Applicant Company name: Motorola Solutions Inc Contact Name: Robert Sarocka Address: 2000 Progress Parkway, Schaumburg IL 60196 Telephone No: 847-344-6075 Email: [email protected] FCC ID Number: ABZ99FT4096B Signature: Date: 12/14/22 Signed by (printed name): Robert Sarocka

FCC ID: ABZ99FT4096B HVIN: SLR5700-UHF1B CONFIDENTIALITY REQUESTED Date: December 8. 2022 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams (Included in Exhibit B) Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation (Included in Exhibit B) Short Term Permanent Parts List & Placement/BOM (Included in Exhibit B) Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics (Included in Exhibit B) Short Term Test Setup Photos Short Term Permanent* User’s Manual Motorola Solutions has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Short Term Confidentiality: The applicant requests the exhibits listed above as Short Term confidential be withheld from public review for a duration of 180 days from the date of submission. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ Robert Sarocka (Signature) (Print name) Title: Engineering Manager

Photographs of the Device EXHIBIT C2-1 External Front View of Base Radio APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Photographs of the Device EXHIBIT C2-2 External Front View of Base Radio, Top Cover and Front Panel Removed APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Photographs of the Device EXHIBIT C2-3 External Back View of Base Radio APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B

Photographs of the Device EXHIBIT C2-3 External Back View of Base Radio APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Photographs of the Device EXHIBIT C2-4 FCC / IC Identification Label APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B

Motorola Solutions Canada, Inc. UPN Number: 3790B Company Number: 109AB HVIN: SLR 5700-UHF1B Page 1 RF Exposure Technical Brief This Technical Brief calculates the minimum separation distance from an antenna, connected to the subject base station, such that the power density value listed in RSS-102, Radio Frequency (RF) Exposure Compliance of Radiocommunications Apparatus (All Frequency Bands) Issue 5 Table 6 is not exceeded. The analysis is for a typical installation using a structure mounted antenna. Within the frequency range that the subject equipment operates, 406.1 MHz – 470 MHz the permitted exposure limit is frequency dependent per the equation 0.6455*sqrt(f). Table 1 lists the maximum permitted exposure limits for the lowest and highest operating frequencies. The smaller maximum permissible exposure limit will be used for the computation because it requires a larger separation distance from the antenna to the exposed person. Table 1 - Maximum Permissible Exposure Limits Controlled Environment Frequency 406.1 MHz 470 MHz Limit 13.0 W/m 2 14.0 W/m 2 Example Calculations for SLRr 5700, UHF Transmitter: The example configuration is a single frequency site, with minimal RF network losses, set to zero for this example, between the transmitter output connector and the antenna input connector. The antenna has an omni directional pattern in the horizontal plane. Table 2 lists the key RF system and antenna parameters. Table 2 - Transmitter Configuration Frequency 406.1-470 MHz Base Station Output Power 60 W RF Network Loss 0 dB Antenna Type DS3X00P36U-D 0 dBd / 2.1 dBi (Omni) Antenna length 0.91m Controlled Environment: Cylindrical Method 1 Using Equation 1 the spatially averaged plane-wave equivalent power density parallel to the antenna in the vertical plane is estimated by dividing the net input power to the antenna by the surface area of an imaginary cylinder at a distance R from the antenna, with the height of the cylinder equal to the length of the antenna 2 . Rh Pnet S 2  (1) 1 Federal Communications Commission Office of Engineering & Technology, OET Bulletin 65, “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields”, Edition 97-01, page 32, Tell’s cylindrical model. 2 Federal Communications Commission Office of Engineering & Technology, OET Bulletin 65, “Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields”, Edition 97-01, page 32, Tell’s cylindrical model. Motorola Solutions Canada, Inc. UPN Number: 3790B Company Number: 109AB HVIN: SLR 5700-UHF1B Page 2 Where: S = power density, W/m 2 Pnet = net input power to the antenna, W R = radial distance from the antenna, m h = height of the antenna, m The minimum separation distance can be found by solving Equation 1 for R and setting S to the smaller maximum power density for the environment per Table 1. 81.0 91.00.132 60 2    xhS Pnet R  m (2) For the example site configuration the minimum separation distance for a controlled environment is 1.48 m.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Measurements Report The measurement report shows compliance information against applicable standards. Each parameter is measured generally at the low end, middle, and at the high end of the applicable frequency band. Each section of the report contains either verbiage or graphs which show compliance to applicable standards as required, explains testing method used, and indicates what the applicable specification is. Test setup details and certification signoff page are included at the end of the measurement report. INDEX EXHIBIT DESCRIPTION E1-1 Tested Unit Details E1-2 Measurement Uncertainties E1-3 Test Results Summary E1-4 RF Output Power E1-5 Occupied Bandwidth E1-6 Conducted Spurious Emissions E1-7 Radiated Spurious Emissions E1-8 Frequency Stability E1-9 Frequency Transient Behavior E1-10 Audio Frequency Response – Modulation Characteristics E1-11 Audio Modulation Limiting – Modulation Characteristics E1-12 Test Setup Details E1-13 Statement of Certification E- 1 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-1 Tested Unit Details Model Under Test SLR 5700 Serial Number 478IYW0761 Firmware Version D20.22.03.09 Codeplug Version 226303 Bootloader Version R01.11.02 Manufacturer Motorola Solutions 2540 Galvin Drive, Elgin, IL 60124 E- 2 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-2: Measurement Uncertainty Measurement Frequency Expanded Uncertainty RF Power Output 50MHz-10GHz +/-0.132dB Carrier Frequency Stability 9kHz-13GHz +/-0.368Hz Occupied Bandwidth 9kHz-13GHz +/-0.52dB Transmitter Conducted Spurious Emissions 9kHz-13GHz +/-0.64dB Transient Frequency Behavior 9kHz-13GHz +/-2.04dB Modulation Characteristics 100Hz-5000Hz +/-0.40dB Radiated Emissions 30MHz-1000MHz 4.3dB Radiated Emissions 1GHz-6GHz 3.1dB E- 3 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1.3: Test Results Summary Test 47 CFR Reference RSS-119 Reference Results RF Output Power 2.1046 4.1,5.4 Pass Occupied Bandwidth 2.1049 5.5 Pass Conducted Spurious Emissions 2.1051 4.2,5.8 Pass Radiated Spurious Emissions 2.1053 4.2,5.8 Pass Frequency Stability 2.1055 5.3 Pass Frequency Transient Behavior 90.214 5.9 Pass Modulation Characteristics 2.1047 Pass Test Standards: Title 47 Part 2 of Code of Federal Regulations Title 47 Part 90 of Code of Federal Regulations RSS-119 Land Mobile and Fixed Equipment Operating in the Frequency Range 27.41-960 MHz ANSI C63.26-2015 American National Standard for Compliance Testing of Transmitters Used in Licensed Radio Services ANSI C63.4-2014 American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range 9 kHz to 40 Ghz E- 4 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-4 RF Power Output Data per CFR 47 2.1046 and RSS-119 5.4 The RF power output was measured with the indicated voltage applied to and current into the final RF amplifying device(s). The DC current indicated is the total for the final RF amplifier stage. Analog Voice (FM) and Digital MOTOTRBO TM 4-Level Frequency Modulation (4FSK) 406MHz 420MHz 430Hz Measured RF output 60 60 60 Watts DC Voltage, final RF amplifier stage/stages 13.6 13.6 13.6 Volts DC Current, final RF amplifier stage/stages 8.2 7.9 7.7 Amps Input power for final RF amplifying device(s) 112 107 105 Watts Primary Radio Input Supply Voltage 120 120 120 VAC Minimum Measured RF output 1 1 1 Watts DC Voltage, final RF amplifier stage/stages 13.6 13.6 13.6 Volts Normal DC Current 2.2 2.2 2.2 Amps Input power for final RF amplifying device(s) 30 30 30 Watts Primary Radio Input Supply Voltage 120 120 120 VAC Frequency Modulation and Compatible 4-Level Frequency Modulation Mode: 450 MHz 460 MHz 470 MHz Measured RF output 60 60 60 Watts DC Voltage, final RF amplifier stage/stages 13.6 13.6 13.6 Volts DC Current, final RF amplifier stage/stages 7.9 8.4 8.8 Amps Input power for final RF amplifying device(s) 107 114 120 Watts Primary Radio Input Supply Voltage 120 120 120 VAC Minimum Measured RF output 1 1 1 Watts DC Voltage, final RF amplifier stage/stages 13.6 13.6 13.6 Volts Normal DC Current 2.2 2.2 2.2 Amps Input power for final RF amplifying device(s) 30 30 30 Watts Primary Radio Input Supply Voltage 120 120 120 VAC E- 5 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-5 Occupied bandwidth per CFR 47 2.1051 and RSS-119 5.5 Occupied Bandwidth – MOTOTRBO TM Digital Modulation, 12.5 kHz Channel Spacing MOTOTRBO TM Digital Modulation can be used in a system configuration based upon channel usage as described in Exhibit B. The ‘F7E’ and ‘FXE’ emission designators provide usage for telephony, the ‘F7D’ and ‘FXD’ designators provide usage for data / telecommand, and the ‘F7W’ designator provides for usage as a combination of telephony and telecommand. All are spectrally identical. The occupied bandwidth chart references the following setup and specification requirements. Modulation Type: MOTOTRBO TM Digital Modulation Emission Designator: 7K60F7W, 7K60F7D, 7K60F7E, 7K60FXD, 7K60FXE Channelization: 12.5 kHz Power Setting: 60 Watts Specification Requirement 47 CFR §90.210(d) and IC RSS-119 section 5.8.3 - Emission Limits – “D-Mask” : Emission Ma…

Text truncated - open the document above for the full version.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10 Audio Frequency Response Specification Requirement per TIA 603: Audio Frequency Response, 25 kHz Channels: The audio frequency response from 300 Hz to 3000 Hz shall not vary more than +1 dB or -3 dB from a true 6 dB per octave pre-emphasis characteristic as referenced to the 1000 Hz level, with an additional 6 dB per octave attenuation allowed from 500 Hz to 300 Hz, and an additional 6 dB per octave attenuation is allowed from 2500 Hz to 3000 Hz in equipment operating in the 25 MHz to 869 MHz range. Audio Frequency Response, 12.5 kHz Channels: The audio frequency response from 300 Hz to 3000 Hz shall not vary more than +1 dB or -3 dB from a true 6 dB per octave pre-emphasis characteristic as referenced to the 1000 Hz level, with an additional 6 dB per octave attenuation allowed from 500 Hz to 300 Hz. An additional 6 dB per octave rolloff is allowed from 2300 Hz to 2700 Hz, and an additional 12 dB per octave is allowed from 2700 Hz to 3000 Hz in equipment operating in the 896 MHz to 940 MHz range or for 12.5 kHz channel operation. Modulation: Audio Test Tone Carrier Frequency: Performance was measured at carrier frequencies at the low end, middle, and high end of the operating band.. Specification: The specification limit is shown on the response plots EXHIBIT DESCRIPTION E1-10.1 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 406.1125 MHz E1-10.2 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 420.0125 MHz E1-10.3 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 429.9875 MHz E1-10.4 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 450.0125 MHz E1-10.5 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 460.0125 MHz E1-10.6 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 469.9875 MHz E- 71 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.7 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 406.1125 MHz E1-10.8 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 420.0125 MHz E1-10.9 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 429.9875 MHz E1-10.10 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 450.0125 MHz E1-10.11 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 460.0125 MHz E1-10.12 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 469.9875 MHz E- 72 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.1 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 406.1125 MHz E1-10.2 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 420.0125 MHz E- 73 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.3 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 429.9875 MHz E1-10.4 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 450.0125 MHz E- 74 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.5 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 460.0125 MHz E1-10.6 Audio Frequency Response – Modulation Characteristics, 25 kHz Channels – 469.9875 MHz E- 75 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.7 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 406.1125 MHz E1-10.8 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 420.0125 MHz E- 76 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.9 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 429.9875 MHz E1-10.10 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 450.0125 MHz E- 77 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-10.11 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 460.0125 MHz E1-10.12 Audio Frequency Response – Modulation Characteristics, 12.5 kHz Channels – 469.9875 MHz E- 78 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-11 Modulation Limiting Specification Requirement per TIA 603: Modulation Limiting, 25 kHz Channels: The maximum instantaneous peak and steady state deviations shall not exceed the rated system deviation of +/- 5 kHz at any audio frequency or change in level as specified in the method of measurement. The minimum value of modulation limiting shall be at least 60% of the rated system deviation, or 3 kHz. Modulation Limiting, 12.5 kHz Channels: The maximum instantaneous peak and steady state deviations shall not exceed the rated system deviation of +/- 2.5 kHz at any audio frequency or change in level as specified in the method of measurement. The minimum value of modulation limiting shall be at least 60% of the rated sys…

Text truncated - open the document above for the full version.

APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-12 Test Setup Details Test Location: (for all tests except radiated emissions) Motorola Solutions, Inc., Schaumburg Lab 2000 Progress Parkway, Schaumburg, IL 60196 FCC Registration Number 786245 IC CAB Identifier US0220 Test Engineer Matt Nawrocki (for radiated emissions) Elite Electronic Engineering Inc. 1516 Centre Circle Dr., Downers Grove, IL 60515 FCC Registration Number 269750 IC Registration Number 2987A IC CAB Identifier US0107 Test Engineer Tylar Jozefczyk E- 93 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Test Setup: Motorola Solutions RF Output Power, Occupied Bandwidth, Frequency Stability, Frequency Transient Behavior, Modulation Characteristics E- 94 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Conducted Spurious Emissions Close-in E- 95 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Conducted Harmonic Emissions 6 E- 96 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Test Setup: Elite E- 97 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E- 98 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E- 99 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E- 100 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Test Equipment List – Motorola Solutions Manufacturer Model Serial Number Description Last Cal Due Date Keysight/Agilent/HP N9030A MY53310751 PXA Signal Analyzer, 3 Hz to 50 GHz 09-07-2022 09-07-2024 Keysight/Agilent/HP U8903A my50500002 Audio Analyzer, 10 Hz to 100 kHz 09-04-2022 09-04-2023 Rohde & Schwarz NRP-Z11 101590 Power Sensor 08-31-2022 8-31-2024 Rohde & Schwarz SMU200A 101350 Signal Generator / Power Meter 12-30-2021 12-29-2024 Keysight/Agilent/HP 34401A 3146A59752 Digital Multimeter 08-29-2022 08-29-2026 Keysight/Agilent/HP 8482a gg00004032 Power Sensor 08-30-2022 08-30-2023 Keysight/Agilent/HP E5071C MY46316134 ENA Series Network analyzer 08-31-2022 09-31-2023 Thermotron WS-120-C HM-15-15 52516 Temperature Chamber 03-07-2022 03-07-2024 Keysight/Agilent/HP E4440A my46185813 PSA Spectrum Analyzer 3 Hz - 26.5 GHz 09-06-2022 09-06-2024 Keysight/Agilent/HP 8753es us39175306 S-parameter Network Analyzer 09-01-2022 09-01-2023 E- 101 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. Test Equipment List – Elite E- 102 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E1-13 Statement of Certification The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: College Degree: BSEE, University of Illinois, Urbana-Champaign, Illinois, USA __37___ years of Design and Development experience in the field of two-way radio communication. NAME: Robert Sarocka SIGNATURE: ___________________________ DATE: December 12, 2022 POSITION: Technical Manager I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME: Jerry Flondro SIGNATURE: DATE: December 12, 2022 POSITION: Director REPORT END E- 103 APPLICANT: MOTOROLA SOLUTIONS EQUIPMENT TYPE: ABZ99FT4096B 109AB-99FT4096B Report on Test Measurements for FCC ID ABZ99FT4096B, HVIN SLR 5700-UHF1B per FCC 47 CFR 90 and IC RSS-119. E- 104