ABZ99FT5000HT1250LS+ 700MHz Portable Radio

Motorola, The Stylized M logo, Professional Radio - As Dedicated As You Are, HT Series,HT1250 • LS + , and Call Alert are trademarks of Motorola, Inc. PassPort is a trademark of Trident Micro Systems.LTR is a trademark of E.F. Johnson Company. © 1999, 2000, 2001 Motorola, Inc. All rights reserved. Printed in U.S.A. *6864110R11*6866110R11-O HT1250 •• LS ++ User Guide Professional Radio - As Dedicated As You Are ™ 6864110R11-O_cvr.qxd 11/30/01 2:09 PM Page 1 1 English CONTENTS CONTENTS Computer Software Copyrights . . . . . . . . . 5Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7User Safety, Training, andGeneral Information . . . . . . . . . . . . . . . . . . 7Compliance with RF Energy ExposureStandards. . . . . . . . . . . . . . . . . . . . . . . . . . 7Operational Instructions and TrainingGuidelines . . . . . . . . . . . . . . . . . . . . . . . . . 8 Transmit and Receive . . . . . . . . . . . . . . 8Hand-held Radio Operation . . . . . . . . . 8Body-worn Operation . . . . . . . . . . . . . . 8Antenna & Batteries . . . . . . . . . . . . . . . 9Approved Accessories . . . . . . . . . . . . . 9 Electromagnetic Interference/Compatibility 9 Facilities . . . . . . . . . . . . . . . . . . . . . . . . 9Aircraft. . . . . . . . . . . . . . . . . . . . . . . . . . 9Medical Devices . . . . . . . . . . . . . . . . . 10Driver Safety . . . . . . . . . . . . . . . . . . . . 10 Operational Warnings . . . . . . . . . . . . . . . 11 For Vehicles With an Air Bag . . . . . . . 11Potentially Explosive Atmospheres . . . 11Blasting Caps and Areas . . . . . . . . . . 11 Operational Cautions. . . . . . . . . . . . . . . . . 12 Antennas . . . . . . . . . . . . . . . . . . . . . . .12Batteries . . . . . . . . . . . . . . . . . . . . . . . . 12 Battery Information . . . . . . . . . . . . . . . . . . 12 Charging Batteries . . . . . . . . . . . . . . . .12 Introduction . . . . . . . . . . . . . . . . . . . . . . .13Trunked Radio Systems . . . . . . . . . . . . . . 13 PassPort™ Trunked Systems . . . . . . . 13LTR™ Trunked Systems . . . . . . . . . . . 13 Conventional Radio Systems . . . . . . . . . .14HT1250•LS+ Radio Features . . . . . . . . . .14 Radio Wide Features . . . . . . . . . . . . . . 14PassPort Zone Features . . . . . . . . . . . 14LTR Zone Features . . . . . . . . . . . . . . . 15Conventional Zone Features . . . . . . . . 15 Radio Overview . . . . . . . . . . . . . . . . . . . . 17Parts of the Radio . . . . . . . . . . . . . . . . . . . 17 HT1250•LS+ Model . . . . . . . . . . . . . . . 17On/Off/Volume Knob . . . . . . . . . . . . . . 18Zone Selector Knob . . . . . . . . . . . . . . . 18LED Indicator . . . . . . . . . . . . . . . . . . . . 18Push-to-Talk (PTT) Button . . . . . . . . . . 18Microphone. . . . . . . . . . . . . . . . . . . . . . 18Menu Keys . . . . . . . . . . . . . . . . . . . . . . 18Keypad Keys . . . . . . . . . . . . . . . . . . . . 19 6864110R11-OTOC.fm Page 1 Tuesday, November 20, 2001 11:56 AM 2 English CONTENTS Display . . . . . . . . . . . . . . . . . . . . . . . . . 21Programmable Buttons . . . . . . . . . . . . 22 Audio Indicators for ProgrammableButtons . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Battery Information . . . . . . . . . . . . . . . . . . 29 Charging the Battery . . . . . . . . . . . . . . 29 Getting Started . . . . . . . . . . . . . . . . . . . . 29 Battery Charge Status . . . . . . . . . . . . . 30Attaching the Battery . . . . . . . . . . . . . . 31Removing the Battery . . . . . . . . . . . . . 31 Accessory Information . . . . . . . . . . . . . . . 31 Attaching the Antenna . . . . . . . . . . . . . 31Removing the Antenna . . . . . . . . . . . . 32Attaching the Belt Clip . . . . . . . . . . . . . 33Removing the Belt Clip . . . . . . . . . . . . 33Attaching the Side Connector Cover . . 34 Turning the Radio On or Off . . . . . . . . . . . 34Adjusting the Volume . . . . . . . . . . . . . . . . 35Selecting a Trunked Zone and Talkgroup. 35Sending a Trunked Call . . . . . . . . . . . . . . 36Selecting a Conventional Zone andChannel . . . . . . . . . . . . . . . . . . . . . . . . . . 37Sending a Conventional Call . . . . . . . . . . 37Receiving a Trunked or Conventional Call 37Repeater or Talkaround J Mode (Conventional Operation Only) . . . . . . . . . 38 Call Light (Trunked Operation Only) . . . . . . . . . . . . 38Home Channel Revert . . . . . . . . . . . . . . . 39Sounding an Emergency Siren . . . . . . . . 39 To Start the Emergency Siren. . . . . . . 39To Stop the Emergency Siren . . . . . . . 39 PASSPORT TRUNKING . . . . . . . . . . . . . 41Seamless Roaming . . . . . . . . . . . . . . . . . 41 Initial Registration . . . . . . . . . . . . . . . . 41Roaming and Registering BetweenSites . . . . . . . . . . . . . . . . . . . . . . . . . . 42Site/MIN View . . . . . . . . . . . . . . . . . . . 43 Roam Request . . . . . . . . . . . . . . . . . . . . . 43 To Start a Roam Request . . . . . . . . . 44To Cancel a Roam Request . . . . . . . . 44 Site Lock . . . . . . . . . . . . . . . . . . . . . . . . . 45 To Start Site Lock . . . . . . . . . . . . . . . . 45To Cancel Site Lock . . . . . . . . . . . . . . 45 Troubleshooting . . . . . . . . . . . . . . . . . . . . 46Making a Selective Call . . . . . . . . . . . . . . 47Radio Calls(Trunked Operation Only) . . . . . . . . . . . 47Receiving a Selective Call F . . . . . . . . . . 48 Receiving a Call Alert Page . . . . . . . . . . . 49 6864110R11-OTOC.fm Page 2 Tuesday, November 20, 2001 11:56 AM 3 English CONTENTS Radio Check(LTR Trunked Operation Only) . . . . . . . . . 49Editing a Radio Call List K . . . . . . . . . . . 50 Name and Call Tone Tagging(LTR Trunked Operation Only) . . . . . . . . . 51 To Tag a Specific User ’ s Name . . . . . . 52 To Tag a Type of Radio Call . . . . . . . . 52 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Talkback . . . . . . . . . . . . . . . . . . . . . . . . . . 55PassPort Primary Auto Group Scan . . . . . 56Passport Group Scan G (PassPort Trunked Operatio…

Text truncated - open the document above for the full version.

55 English SCAN SCAN Your radio is equipped with the Scan feature, which allows you to search for, lock onto, and monitor voice activity on trunked talkgroups and conventional channels.There are five types of Scan available in your radio: • Auto Group Scan • All Group Scan • PassPort Primary Auto Scan • Passport Group Scan • System Scan The table below summarizes the Scan types available in each zone type. Shaded areas indicate that Scan can be enabled through a programmable button (see page 22) or through your radio menu. TALKBACKWhen activity is detected during any type of scan, scanning stops and the active talkgroup or channel appears and remains on the display until scanning resumes. Your dealer can program the amount of time you can respond (or “TALKBACK”) to the caller before your radio resumes scanning.You must press the PTT button to participate in the call; otherwise, scanning continues to the other talkgroups or channels. Zone PassPort Primary Auto Scan Pass- Port Group Scan LT R Auto Group Scan LTR All Group Scan System Scan PassPor t Trunked X X LTR Trunked X X X Conven-tional X Zone PassPort Primary Auto Scan Pass- Port Group Scan LTR Auto Group Scan LTR All Group Scan System Scan 56 English SCAN PASSPORT PRIMARY AUTO GROUP SCANPassPort Primary Auto Group Scan automatically scans the primary (first) talkgroup within the selected PassPort zone. Any time you are positioned on a PassPort talkgroup other than the first one, your radio automatically scans activity on the first talkgroup within that zone.Note: This feature is enabled AUTOMATICALLY with your radio. It is not enabled through the radio menu or through a prepro-grammed scan button. PASSPORT GROUP SCAN G (PASSPORT TRUNKED OPERATION ONLY) PassPort Group Scan scans talkgroups within the selected Passport trunked zone, as programmed by your dealer. Up to 16 different talkgroups can be programmed into each Scan list, with one Scan list assigned to each position on the Zone Selector knob. You can edit these Scan lists through your radio ’ s menu (see page 60). When PassPort Group Scan is Enabled• The G symbol appears on the display. • The LED indicator blinks green during PassPort Group Scan operation; it stops blinking when the radio switches to an active talkgroup or channel. Note: • PassPort Group Scan is not available when registered on a non-home site. • If you switch to another PassPort zone, LTR, or conventional zone while the radio is scan-ning, scanning resumes upon return to the PassPort zone where PassPort Group Scan was enabled. • If the radio is turned off while scanning, the radio resumes scanning when you turn it back on. If the radio registers on a non-home site, scanning is not enabled until the radio regis-ters at its home site. 57 English SCAN To Start or Stop PassPort Group Scan Operation through a Preprogrammed Button (see page 22)• Press the preprogrammed Scan button to start PassPort Group Scan. • Press the preprogrammed Scan button again to stop the PassPort Group Scan. –or–To Start or Stop PassPort Group Scan Operation through the Menu AUTO GROUP SCAN G (LTR TRUNKED OPERATION ONLY)Auto Group Scan automatically scans talkgroups within an LTR trunked zone as programmed by your dealer. Auto Group Scan can be either non-prioritized or prioritized. • Non-prioritized Auto Group Scan automatically scans all talkgroups programmed with Auto Group Scan. • Prioritized Auto Group Scan automatically scans the selected talkgroup and all lower 4-numbered talkgroups. For example, if talkgroups 1, 3, and 4 have been programmed by your dealer with Auto Group Scan and talkgroup 4 is selected, the radio automatically scans talkgroups 1, 3, and 4, and skips talkgroup 2. To Start Auto Group ScanSelect a talkgroup that has been programmed for Auto Group Scan by your dealer. Note: You do not need to press a preprogrammed Scan button. 1 ) to enter menu mode. 2 + or ? until 3 ) to select You see the current scan status. 4 + or ? until – or – 5 ) to confirm your selection. 3DVV*US6FDQ 3DVV *US6FDQ 3S*S6 FDQ2II" 3S*S6FD Q2Q" 58 English SCAN • The G symbol appears on the display when non-prioritized Auto Group Scan has been activated. • The H symbol appears on the display when prioritized Auto Group Scan has been activated. • There is no LED indicator during Auto Group Scan. To Stop Auto Group ScanSelect a talkgroup that has not been programmed for Auto Group Scan by your dealer.ALL GROUP SCAN G (LTR TRUNKED OPERATION ONLY)All Group Scan scans all talkgroups within the selected LTR trunked zone. When All Group Scan is enabled:• The G symbol appears on the display. • The LED indicator blinks green during All Group Scan operation; it stops blinking when the radio switches to an active talk-group. Note: If you enter menu mode while the radio is scanning, scanning stops. It resumes when you exit menu mode. To Start or Stop All Group Scan Operation through the Menu (see page 22)• Press the preprogrammed All Group Scan button once to start All Group Scan. • Press the preprogrammed All Group Scan button again to stop All Group Scan. – or – To Start or Stop All Group Scan Operation through the Menu 1 ) to enter menu mode. 2 + or ? until 3 ) to select You see the current scan status. 4 + or ? until – or – 5 ) to confirm your selection. $OO* URXS6FDQ $OO*U RXS6FDQ $OO*U RXS2Q" $OO*U RXS2II" 59 English SCAN SYSTEM SCAN G (LTR TRUNKED AND CONVENTIONAL OPERATION)System Scan scans trunked talkgroups and conventional channels between LTR and conventional zones, as programmed by your dealer. Up to 16 different talkgroups or conventional channels can be programmed into each Scan list. You can edit these lists through your radio ’ s menu (see page 60). When System Scan is Enabled• The G symbol appears on the display. • The LED indicator blinks green during Sys-tem Scan operation; it stops blinking when the radio switches to an active talkgroup or channel. Note: If you enter menu mode while the radio is scanning, scanning stops. …

Text truncated - open the document above for the full version.

MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 2 SHEET 1 OF 1 CERTIFICATION OF DATA Pursuant to 47 CFR 2.1517(g) The technical data supplied with this application, having been taken under my supervision, is hereby duly certified. The following is a statement of my qualifications: 1) I have received a BSEE degree in Electrical Engineering from Northwestern University, Evanston, Illinois. 2) I have 29 years experience in developing, testing and certifying Land Mobile Communications Products. NAME: James M. Zima SIGNATURE: DATE: March 15, 2002 POSITION: Senior Staff Engineer I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct: NAME: Robert M. Kraus SIGNATURE: DATE: March 15, 2002 POSITION: Engineering Section Manager

EXHIBIT 13A SHEET 1 OF 2 FCC ID: ABZ99FT3080 Date: February 18, 2002 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT3080 Gentlemen: Motorola Inc., 5201 Tollview Drive, Rolling Meadows, Illinois, herein submits application for Certification of the equipment identified by FCC ID number ABZ99FT3080. This transmitter is primarily intended for use in a portable radio application with capabilities for conventional and trunked communications with a transmit power of 1 Watt (+30 dBm) or 5.5 Watts (+37.4 dBm). The subject transmitter complies with CFR Title 47, Section 90.203, in that the operator cannot directly program the transmit frequencies using only the normally accessible external controls of the unit. On December 6, 2001, representatives from Motorola Inc. and one of our customers met with the Commercial Wireless Division to discuss our intention for the use of this equipment, utilizing 12.5 kHz channel spacing with + 2.5 ppm frequency stability, in the 220-222 MHz band. In attendance were representatives from the FCC’s Equipment Authorization Branch and from the Wireless Telecommunications Bureau. At that time we presented an analysis to demonstrate that our intended operation of this equipment would not impact existing 5 kHz users in this band, in that the undesired emissions from our equipment, operating under the frequency assignment guidelines we propose, would not exceed the undesired emissions level from an adjacent 5 kHz user, even if the effects of + 2.5 ppm stability were included. We indicated that the subject transmitter is similar to that previously certified under FCC ID: AZ489FT3794, except having been redesigned for operation in the 217-218, 219-220 and 220-222 MHz bands, and for 12.5 kHz channel spacing only. Because the subject transmitter complies with all applicable rules, and no request for a change of rules was made, it was felt that Certification was achievable. EXHIBIT 13A SHEET 2 OF 2 We are requesting Certification under Part 80 as well as Part 90 of the Commission’s Rules to allow operation of this equipment in the 217-218 MHz and 219-220 MHz AMTS bands, per CFR Title 47 Part 80.385. This equipment meets or exceeds the technical requirements of CFR Title 47 Part 80 Subpart E. The equivalence of G3E phase modulation emission is achieved by frequency modulation with pre-emphasis. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected]

EXHIBIT 13B SHEET 1 OF 1 FCC ID: ABZ99FT3080 REQUEST FOR CONFIDENTIALITY Date: February 18, 2002 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT3080 Gentlemen: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures) and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola is in the process of licensing the technology employed. Please mark Exhibits 4, 5, 10 and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected]

EXHIBIT 13A SHEET 1 OF 1 FCC ID: ABZ99FT5000 Date: March 15, 2002 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT5000 Gentlemen: Motorola Inc., 5201 Tollview Drive, Rolling Meadows, Illinois, herein submits application for Certification of the equipment identified by FCC ID number ABZ99FT5000. This transmitter is intended for use in a portable radio application with capabilities for conventional and trunked communications with an effective radiated power (ERP) of 1 Watt (+30 dBm) or 3.0 Watts (+34.8 dBm). The frequency bands of operation comply with CFR Title 47, Sections 27.5(b) (1) and (2). The subject transmitter complies with CFR Title 47, Section 90.203, in that the operator cannot directly program the transmit frequencies using only the normally accessible external controls of the unit. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected]

FCC ID: ABZ99FT5000 Date: 26 th April 2002 Mr. Martin Perrine Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re: Form 731 Confirmation Number: EA543727 with FCC ID: ABZ99FT5000. Dear Mr. Perrine; Motorola Inc. herein submits its response to the 16 th April 2002 request for information in Correspondence Number 22631. EMC Q1) Statement clarifying maximum conducted power. EMC reports report 3.0 W while the SAR reports 3.1 W. CFR 47 section 90.541 (c) limits power to 3.0 W. R1) The radio submitted for SAR measurement was tuned to its maximum adjustable power setting using specialized software that is not available to the dealer or end user. The CPS (Customer Programming Software) available to the dealer allows the power level of each channel to be programmed to “Low Power” (1.2 watts) or “High Power” (2.75 watts) only. These two power levels are factory-adjusted to a tolerance of + 0.1 watt at several frequencies across the operating band, and this information is stored in the radio. The operating frequency of the channel being programmed is used to choose the power output setting that is appropriate for that frequency. This method gives a very accurate and predictable output power setting which is not subject to variations due to errors in customer or dealer power measurement equipment Q2) New occupied BW plots. Reference levels in the provided plots do not clearly agree with conducted power. R2) New plots are attached in Addendum A as follows (a note stating “0 dB = 3.0 Watts” has been added to each plot): PAGE 6 - Amended Exhibit 6F-5 2500 Hz Audio Modulation Only PAGE 7 - Amended Exhibit 6F-5 2500 Hz Audio and TPL Modulation FCC ID: ABZ99FT5000 PAGE 8 - Amended Exhibit 6F-5 2500 Hz Audio and DPL Modulation PAGE 9 - Amended Exhibit 6F-5 2500 Hz Audio and Low Speed Trunking Modulation PAGE 10 - Amended Exhibit 6F-5 DTMF Modulation Only PAGE 11 - Amended Exhibit 6F-5 DTMF Modulation and TPL Modulation PAGE 12 -Amended Exhibit 6F-5 DTMF Modulation and DPL Modulation PAGE 13- Amended Exhibit 6F-5 DTMF Modulation and Low Speed Trunking Modulation PAGE 14 - Amended Exhibit 6F-5 2000/3000 Hz FSK Data Modulation Only PAGE 15 - Amended Exhibit 6F-5 2000/3000 Hz FSK Data and TPL Modulation PAGE 16 - Amended Exhibit 6F-5 2000/3000 Hz FSK Data and DPL Modulation PAGE 17 - Amended Exhibit 6F-5 2000/3000 Hz FSK Data and Low Speed Trunking Modulation Q3) Block diagram. R3) Block Diagrams have been attached in Addendum A as follows: PAGE 18 – Transmitter and Frequency Synthesizer Block Diagrams PAGE 19 – Frac-N Synthesizer IC and VCO/Buffer IC Internal Block Diagrams PAGE 20 – Transmitter Audio Path and Microcontroller Block Diagram Q4) Additional test procedure details such as write ups, drawings, photographs and calculation for radiated power testing. It is not clear that the substitution method was used and what the final measured value is. Please provide additional test data as appropriate. R4) Radiated power is measured in accordance with TIA/EIA-603-A section 2.2.17. The data presented was corrected for losses using the substitution method, as specified in TIA/EIA-603-A section 2.2.17.2 (d). This procedure is attached in Addendum A : PAGES 21-22 – TIA/EIA-603-A Procedure for Average Radiated Power Output A photograph of the test setup for radiated power and radiated spurious emissions is attached in Addendum A : PAGE 23 – OATS Radiated Power Test Setup (Photo) The EPR data supplied as Exhibits 6A-3 and 6A-4 has been amended to show the radiated power in watts as well as dBm, and are attached in Addendum A : PAGE 24 – Amended Exhibit 6A-3 - RF Output Data – ERP (746, 762 MHz) PAGE 25 – Amended Exhibit 6A-3 - RF Output Data – ERP (776, 794 MHz) FCC ID: ABZ99FT5000 Q5) Additional test procedures for radiated spurious, and conducted spurious tests. It is not clear if all frequencies in the test range were scanned. It appears that only harmonic frequencies were tested. Please, provide additional test data as appropriate. R5) RADIATED SPURIOUS EMISSIONS The equipment submitted for OATS Radiated Spurious Emissions Testing was initially pre-screened using a GTEM (Gigahertz Transverse Electromagnetic) cell which meets the specifications of TIA/EIA-603-A section 1.5.36. IEC 60481-1 compliant signal processing software is used to convert the individual 3-axis dBμV field strength measurement into an OATS-correlatable value. The shielding of GTEM cell eliminates unwanted signals, allowing close inspection of the spurious emissions of the equipment with greater resolution and lower noise floor than is obtainable in an open area test site environment. Any measurable non-harmonically-related emissions are noted. This pre-screening information is supplied to the agency performing the OATS measurement, allowing them to concentrate are areas where spurious emissions may be found. Note that the GTEM data itself is not submitted to the FCC, but only used as an aid to locate spurious emissions which may be overlooked due to ambient signal conditions in the OATS test site. For the case of the subject equipment of this application, no such non-harmonically related spurious emissions were found, and therefore were not reported. Radiated spurious emissions measurements are performed according to the procedures of TIA/EIA-603-A section 2.2.12.2. A non-radiating load is attached directly to the antenna port of the transmitter without RF cable. Photographs of the test fixturing of the equipment are attached in Addendum A : PAGE 26 – OATS Radiated Spurious Emissions Test Setup (Photo) PAGE 26 – OATS Device Under Test with Non-Radiating Load (Photo) CONDUCTED SPURIOUS EMISSIONS The conducted spurious emissions plots of Exhibit 6F have been amended with non- harmonically-related emissions included. All emissions are significantly within FCC limits. The following are attached in Addendum A : PAGE 27 – Amended Exhibit 6F-1 - 3 Watts, 746.500 MHz PAGE 28 – …

Text truncated - open the document above for the full version.

Date:1st May 2002 Mr. Martin Perrine Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Re:Form 731 Confirmation Number EA543727 with FCC ID: ABZ99FT5000 Dear Mr. Perrine; Motorola Inc. herein submits it response to the 29th April 2002 phone call request for additional information regarding our System Performance Check process. The System Performance Check process adopted by the Motorola CGISS EME Lab is consistent with IEEE Std. 1528 (April 4, 2002) paragraph 8.2, FCC Supplement-C (ed. 01-01), and CENELEC SAR Standard EN-50361. Also, System Validation process is consistent with IEEE-1528 (April 4, 2002) paragraph 8.3. System Performance Check target values are determined/measured after system validation using the system check setup. The system validation is performed per IEEE Std. 1528 using reference dipoles listed in Table G.1, head tissue with dielectric properties listed in Table 5.1, and numerical reference SAR values for reference dipoles listed in Table 8.1. (Note: SPEAG dipoles are constructed per IEEE Std. 1528) The resulting measured SAR for both 1g and 10g averages become the new system performance check target values for that specific test frequency and dipole source. Using the same test system and test setup, other dipoles, at this same frequency, that require system performance check targets are measured. For frequencies =>750 MHz, all appropriate dipoles verses all tissue types (head, body), including CENELEC variations that require system performance check SAR targets generated are measured. System performance check target values for 300 MHz and 450 MHz dipoles are generated after performing the system validation using the 835 MHz reference dipole (SPEAG) as stated in IEEE Std. 1528; all appropriate 300 MHz and 450 MHz dipoles verses all tissue types (head, body), including CENELEC variations that require performance check SAR targets generated are then measured. This process is repeated for all required system performance check frequencies. System performance check is performed daily prior to compliance test and the results must be within +/-10% of the previously determined system check target value. It is performed at a central frequency of the transmitting band or, when a radiating source is not available at the operating frequency range of the test device, a source operating within 100 MHz of the mid-band channel is used. For frequencies below 300 MHz, system performance check is performed at 300 MHz.

AMENDED EXHIBIT 13B SHEET 1 OF 1 FCC ID: ABZ99FT5000 AMENDED REQUEST FOR CONFIDENTIALITY Date: July 2, 2002 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Certification of Transmitter with FCC ID: ABZ99FT5000 Gentlemen: Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola is in the process of licensing the technology employed. Additionally, we request that the document “Channel Plan,” submitted on July 2, 2002 in response to correspondence number 23119, also be marked as “Confidential.” This document contains information which is proprietary to the operation of our system. Please mark Exhibits 4, 5, 10, and 12, and “Channel Plan” as “Confidential.” Please contact me if you require any additional information. Sincerely, Donna Tokarz NPR Coordinator Tel: (847) 576-7245 Fax: (847) 538-4312 E-mail: [email protected]

MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 3 SHEET 1 OF 5 FRONT VIEW WITH ANTENNA ATTACHED HT1250•LS+ FULL KEYPAD MODEL SHOWN MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 3 SHEET 2 OF 5 GENERAL VIEWS WITH ANTENNA REMOVED HT1250•LS+ FULL KEYPAD MODEL (LEFT) HT1250•LS+ LIMITED KEYPAD MODEL (RIGHT) MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 3 SHEET 3 OF 5 REAR VIEW WITH BATTERY ATTACHED MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 3 SHEET 4 OF 5 REAR VIEW WITH BATTERY REMOVED SHOWING FCC ID LABEL MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 3 SHEET 5 OF 5 REAR VIEW WITH BATTERY REMOVED SHOWING FCC ID LABEL (CLOSE-UP)

MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 3 SHEET 1 OF 5 FRONT VIEW WITH ANTENNA ATTACHED HT1250•LS+ FULL KEYPAD MODEL SHOWN MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 3 SHEET 2 OF 5 GENERAL VIEWS WITH ANTENNA REMOVED HT1250•LS+ FULL KEYPAD MODEL (LEFT) HT1250•LS+ LIMITED KEYPAD MODEL (RIGHT) MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 3 SHEET 3 OF 5 REAR VIEW WITH BATTERY ATTACHED MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 3 SHEET 4 OF 5 REAR VIEW WITH BATTERY REMOVED SHOWING FCC ID LABEL MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 3 SHEET 5 OF 5 REAR VIEW WITH BATTERY REMOVED SHOWING FCC ID LABEL (CLOSE-UP)

MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 1 SHEET 1 OF 2 IDENTIFICATION LABEL Pursuant to 47 CFR 2.925(a), 2.1033(c), 2.1065 LOCATION A nameplate of the type presented below will be affixed to every transmitter. It will be placed on the outside of the cast housing at the bottom rear of the unit. Shown below is a photo of the actual label affixed to the cast housing of the transmitter. TYPE The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with a minimum peel strength of 40 oz/inch. MOTOROLA INC FCC ID: ABZ99FT3080 EXHIBIT 1 SHEET 2 OF 2 EXHIBIT 1A - GENERAL INFORMATION 1. Production Plans: Quantity production is planned. 2. Application References: TIA/EIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards Code of Federal Regulations Title 47, Part 2, Sec. 2.1033-2.1057, Part 80, and Part 90, Sec.90.210 3. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commission’s rules. The intended use of this transceiver includes applications covered in the Code of Federal Regulations Title 47, Parts 80 and 90. Maximum transmitter power shall not be adjustable by the user. 4. Similar to “Currently Certified Transmitter Type”: AZ489FT3794 – Motorola GP338 Professional Two-Way VHF Portable Radio

MOTOROLA INC FCC ID: ABZ99FT5000 EXHIBIT 1 SHEET 1 OF 2 IDENTIFICATION LABEL Pursuant to 47 CFR 2.925(a), 2.1033(c), 2.1065 LOCATION A nameplate of the type presente…

Text truncated - open the document above for the full version.