ABZ99FT5012800/900 CSA PORTABLE RADIO

Display Portable User Guide XPR TM 6580 IS Professional Digital Two-Way Radio System Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: XPR 6580 IS conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NAG_LACR.book Page i Monday, August 23, 2010 1:03 PM Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. NAG_LACR.book Page ii Monday, August 23, 2010 1:03 PM Contents English iii ContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR IS Series Portable Radios.Important Safety Information . . . . . . . . . . . . . . . . . . v Product Safety and RF Exposure Compliance . . . v Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . vComputer Software Copyrights . . . . . . . . . . . . . . . vi Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Univer sal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5 Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 5 Radio Controls You Will Be Using . . . . . . . . . . . . . . 6 Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7 Assignable Radio Functions . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . 8 Accessing the Programmed Functions . . . . . . . . . . . 8Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Push-To-Talk (PTT) Bu tton . . . . . . . . . . . . . . . . . . . 10 Switching Between Conventional and Trunking Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Identifying Status Indicators . . . . . . . . . . . . . . . . . . 11 Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Main Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12In-Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Making and Receiving Calls . . . . . . . . . . . . . . . . . . 14 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 15Receiving and Responding to a Radio Call . . . . . . 15 Receiving and Responding to a Group Call . . . . . 15Receiving and Responding to a Private Call . . . . 16 Receiving and Responding to a Phone Call . . . . 17 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 17 Making a Call with the Chan nel Selector Knob . . 18 NAG_LACR.book Page iii Monday, August 23, 2010 1:03 PM Contents English iv Making a Group Call . . . . . . . . . . . . . . . . . . . . 18Making a Private Call . . . . . . . . . . . . . . . . . . . . 18Making an Enhanced Private Call . . . . . . . . . . 19Making a Phone Call . . . . . . . . . . . . . . . . . . . . 20Sending a Status Call . . . . . . . . . . . . . . . . . . . 20Using the Dynamic Regrouping Feature . . . . . 21 Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 23 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 23Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 23 Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . . 24 Scan Lists . .…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 2 SHEET 1 OF 1 EXHIBIT 2 STATEMENT OF CERTIFICATION - Pursuant to 47 CFR 2.907 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received an Electrical and Electronic Engineering degree from Universiti Sains Malaysia Malaysia. 2) I have 2 years experience in developing and testing Land Mobile Communications Products. NAME: Lokesh Anand Vijayakumaran SIGNATURE: /m/LokeshAnand(signed) DATE: August 12, 2010 POSITION: Electrical Design Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Wong Doh Hiik SIGNATURE: /s/DH (signed) DATE: August 12, 2010 POSITION: Engineering Section Manager

EXHIBIT 13A SHEET 1 FCC ID: ABZ99FT5012 Date: July 20, 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: APPLICATION FOR CERTIFICATION OF 800/900 TRANSMITTER WITH FCC ID: ABZ99FT5012 Dear Sir / Madam, Motorola Inc., 1302 E. Algonquin, Schaumburg, IL herein submits application for Certification of the equipment identified by FCC ID number ABZ99FT5012. This transmitter is primarily intended for use in a portable radio application with capabilities for conventional communications with a conducted transmit power of 1 Watt, and 1.2W and max power. The subject transmitter complies with CFR Title 47, Section 90.203, in that the operator cannot directly program the transmit frequencies using only the normally accessible external controls of the unit. Enclosed is a complete Certification Application. Please contact me if you require any additional information. Sincerely, /s/Larry D. Larsen(signed) Larry D. Larsen FCC Coordinator Email: [email protected]

EXHIBIT 13B SHEET 1 FCC ID: ABZ99FT5012 REQUEST FOR CONFIDENTIALITY Date: July 20, 2010 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: APPLICATION FOR CERTIFICATION OF 800/900 TRANSMITTER WITH FCC ID: ABZ99FT5011 Dear Sir / Madam, Motorola is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457 (d) and Section 552 (b) (4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential.” Please contact me if you require any additional information. Sincerely, /s/Larry D. Larsen(signed) Larry D. Larsen FCC Coordinator Email: [email protected]

Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 EXTERNAL PHOTOGRAPHS - Pursuant to 47 CFR 2.1033(c) 12 FIGURE 3-1: FRONT VIEW OF IECEx/CSA PORTABLE RADIO - FULL DISPLAY AND KEYPAD MODEL Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 2 OF 7 FIGURE 3- 2: BACK VIEW OF IECEx/CSA PORTABLE RADIO Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 3 OF 7 FIGURE 3-3: LEFT SIDE (PTT) OF THE IECEx/CSA PORTABLE RADIO Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 4 OF 7 FIGURE 3-4: RIGHT SIDE OF THE IECEx/CSA PORTABLE RADIO Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 5 OF 7 FIGURE 3-5: FCC AND SAFETY LABELS LOCATION OF IECEx/CSA PORTABLE RADIO FCC Label Location Safety Label Location Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 6 OF 7 FIGURE 3-6: CLOSE UP VIEW OF THE SAFETY LABEL. FIGURE 3-7: IECEx/CSA PORTABLE RADIO BATTERY NO Kit NUMBER BATTERY TYPE 1. NNTN7789A Li-Ion 1750mAH Impres Battery Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 3 SHEET 7 OF 7 FIGURE 3-8: IECEx/CSA PORTABLE RADIO ANTENNAS NO ATTENNA TYPE COLOUR LENGTH 1. Whip (MOTOTRBO 800/900 GPS Whip Antenna 806-941 MHz) Blue 18 cm Model List Sales Model Regional Super Tanapa Name Plate Description AAH55UCH9LB3AN PMUF1473AJNBD XPR 6580 IS MOTOTRBO 806-870,896-941 1.0 W,FKP w/GPS

Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 1 SHEET 1 OF 1 EXHIBIT 1 IDENTIFICATION LABEL - Pursuant to 47 CFR 2.925(a) & 2.1033(c) (11) EXHIBIT 1A - LABEL LOCATION A nameplate of the type presented below will be affixed to every transmitter. It will be placed on the bottom of the unit near the front. Shown below is a photo of the actual label affixed to the cast chassis of the transmitter. EXHIBIT 1B - LABEL TYPE The label is a paper polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. Figure 1-1: FCC Label EXHIBIT 1C - GENERAL INFORMATION 1. Application References: TIA/EIA-603B Land Mobile FM or PM Communications Equipment Measurement and Performance Standards Code of Federal Regulations Title 47, Part 2, Sec. 2.1033-2.1057 and Part 90, Section 90.210 2. Data Submittal Procedure: Data is supplied in accordance with Part 2, Sub-part J of the Commission’s rules. The intended use of this transceiver includes applications covered in the Code of Federal Regulations Title 47 and Part 90. Maximum transmitter power shall not be adjustable by the user. 3. Applicable Reference • Reference Certification FCC ID: ABZ99FT5012 • EIA/TIA-603 Land Mobile FM or PM Communications Equipment Measurement and Performance Standards. • FCC Federal Regulations Part 47 Sec. 2.1033-2.1057 • FCC Federal Regulations Part 90 Sec.90.210

Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 9 SHEET 1 OF 3 EXHIBIT 9 INTERNAL PHOTOGRAPHS – PURSUANT 47 CFR 2.1033 ( C) 12 FIGURE 3- 1: NEO CSA COMPLETE INTERNAL OPEN UP VIEW. Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 9 SHEET 2 OF 3 FIGURE 3- 2: NEO CSA WITH OPTION BOARD. Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 9 SHEET 3 OF 3 FIGURE 3-3: NEO CSA CHASIS, BOARD AND CAN SHIELDS

APPLICANT: MOTOROLA INC. FCC ID: ABZ99FT5012 EXHIBIT 11 SHEET 1 OF 1 EXHIBIT 11 RF EXPOSURE INFORMATION - Pursuant 47 CFR 2.1093 In accordance with 47 CFR 2.1093 (c) this transmitter has been subjected to routine environmental evaluation for RF exposure and found to be compliant with the limits specified in 47 CFR 2.1093 (d) (1) for portable devices, using measurements per methods stated in 47 CFR 2.1093 (d) (3) . The complete S.A.R. EME Compliance Test Report is attached.

SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 1 of 54 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Technology Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 8/9/2010 Report Revision: O Report ID: SAR rpt_PMUF1473A_Rev O _100809_ SR8414& SR8525 * Refer to section 15 of part 1 highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams results are not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Responsible Engineer: Veeramani Veerapan (Senior EME Engineer) Report Author: Veeramani Veerapan (Senior EME Engineer) Date/s Tested: 6/10/10~7/22/10 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 6/08/10 DUT Description: XPR 6580 IS 806-870MHz & 896-941MHz, 12.5k/25k, 1W, 160CH, FKP w GPS (Capable of analog FM transmission and digital TDMA transmission.) Test TX mode(s): CW (PTT) Max. Power output: 1.2 Watts Nominal Power: 1.0 Watts Tx Frequency Bands: TMO: 806-825, DMO: 851-870 (800 band) & TMO: 896-902, DMO: 935-941 (900 band) Signaling type: FM and TDMA 2:1 Model(s) Tested: PMUF1473A Model(s) Certified: PMUF1473A Serial Number(s): 477TLL0008, 477TLL0009 Classification: Occupational/Controlled FCC ID: ABZ99FT5012; Rule part 90 (806-824, 851-869, 896-901 & 935-940MHz) IC ID: 109AB-99FT5012 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 8/18/2010 Certification Date: 6/24/2010 Certification No.: L1100650P SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 2 of 54 Part 1 of 2 1.0 Introduction ........................................................................................ 4 2.0 Abbreviations / Definitions ................................................................ 4 3.0 Referenced Standards and Guidelines ................................................ 4 4.0 SAR Limits ......................................................................................... 5 5.0 SAR Result Scaling Methodology ..................................................... 5 6.0 Description of Device Under Test (DUT) .......................................... 6 7.0 Optional Accessories and Test Criteria .............................................. 6 7.1 Antennas .................................................................................... 7 7.2 Batteries..................................................................................... 7 7.3 Body worn Accessories ............................................................. 7 7.4 Audio Accessories ..................................................................... 7 8.0 Description of Test System ................................................................ 8 8.1 Description of Robotics/Probes/Readout Electronics ............... 8 8.2 Description of Phantom(s)......................................................... 8 8.2.1 Dual Flat Phantom......................................................... 8 8.2.2 SAM Phantom ............................................................... 8 8.2.3 Elliptical Phantom ......................................................... 9 8.3 Description of Simulated Tissue ............................................... 9 9.0 Additional Test Equipment .............................................................. 10 10.0 SAR Measurement System Verification .......................................... 10 10.1 Equivalent Tissue Test Results ............................................... 10 10.2 System Check Test Results ..................................................... 11 11.0 Environmental Test Conditions........................................................ 12 12.0 DUT Test Methodology ................................................................... 12 12.1 Measurements.......................................................................... 12 12.2 DUT Configuration(s) ............................................................. 13 12.3 DUT Positioning Procedures................................................... 13 12.3.1 Body ............................................................................ 13 12.3.2 Head............................................................................. 13 12.3.3 Face ............................................................................. 13 12.4 DUT Test Channels ................................................................. 13 12.5 DUT Test Plan......................................................................... 13 12.5.1 General Test Flowchart ................................................ 14 13.0 DUT Test Data ................................................................................. 15 13.1 806-825MHz Test Data ......................…

Text truncated - open the document above for the full version.

SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 1 of 61 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Technology Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 8/9/2010 Report Revision: O Report ID: SAR rpt_PMUF1473A_Rev O _100809_ SR8414& SR8525 * Refer to section 15 of part 1 highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams results are not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Responsible Engineer: Veeramani Veerapan (Senior EME Engineer) Report Author: Veeramani Veerapan (Senior EME Engineer) Date/s Tested: 6/10/10~7/22/10 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 6/08/10 DUT Description: XPR 6580 IS 806-870MHz & 896-941MHz, 12.5k/25k, 1W, 160CH, FKP w GPS (Capable of analog FM transmission and digital TDMA transmission.) Test TX mode(s): CW (PTT) Max. Power output: 1.2 Watts Nominal Power: 1.0 Watts Tx Frequency Bands: TMO: 806-825, DMO: 851-870 (800 band) & TMO: 896-902, DMO: 935-941 (900 band) Signaling type: FM and TDMA 2:1 Model(s) Tested: PMUF1473A Model(s) Certified: PMUF1473A Serial Number(s): 477TLL0008, 477TLL0009 Classification: Occupational/Controlled Rule ID: ABZ99FT5012; Rule part 90 (806-824, 851-869, 896-901 & 935-940MHz) IC ID: 109AB-99FT5012 Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola EME Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 8/18/2010 Certification Date: 6/24/2010 Certification No.: L1100650P SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 2 of 61 Appendix C Dipole Calibration Certificates SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 3 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 4 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 5 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 6 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 7 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 8 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 9 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 10 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 11 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 12 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 13 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 14 of 61 SR8414&SR8525 EMS EME Form-SAR-Rpt-Rev. 11.00 Page 15 of 61 Appendix D Test System Verification Scans The SAR result indicated on the Manufacture’s Calibrated certificate for dipole D900V2 S/N 1d025 and D900V2 S/N 1d026 was not used due to the following: -- The IEEE1528-2003 and the FCC OET-65 Supplement C, System Verification section indicated that “The measured 1-g SAR should be within 10% of the expected target values specified for the specific phantom and RF source used in the system verification measurement.” -- SPEAG calibration certificate indicated that the allowed tolerance for this dipole is higher than +/- 10% (e.g. 10.9 +/-17 % at k=2 for the D900V2 S/N 1d025 and 11.0 +/-17 % at k=2 for the D900V2 S/N 1d026). -- The allowed tolerance for the probes is also higher than +/- 10% (e.g. 11% at k=2 at 900MHz for the probe being used to assess this product). Due to probe, dipole and system tolerances noted above, the lab averages dipole results across multiple probes to establish a set of averaged targets for each dipole using the following procedure: • The System Validation was conducted per IEEE1528-2003 and the latest draft of IEC62209-2 (10/3/08) standards using the simulated head tissue and multiple probes that are available and applicable for the dipole under test to verify the System Validation. Results for this dipole are within the measurement system uncertainty of the reference SAR values indicated within the latest draft of IEC62209-2 (10/3/08) when uses flat phantom with 2mm thickness is used. These results then are averaged and used as the target for the daily system performance check when the simulated head tissue is used. •The dipole targets for the body are set immediately following the same process noted above. Since there is no standard referencing the SAR values for the System Validation using the simulated body tissue, the compliant System Validation results using the simulated head tissue are used to justify the use of the System Validation results using the simulated body tissue due to the same setup except for the simulated tissue type. The targets set in this report were conducted following the above process. Noted that the target set for the tested dipole, when used the simulated head tissue, meets the requirement for the system validation per IEEE1528-2003 the latest draft of IEC62209-2 (10/3/08) standards, and the difference between this result and the result…

Text truncated - open the document above for the full version.

Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 6 SHEET 1 OF 75 EXHIBIT 6 INDEX OF SUBMITTED MEASURED DATA This exhibit contains the measured data for this equipment as follows: EXHIBIT 6A – RF Power Output EXHIBIT 6B – Audio Frequency Response 6B-1: 12.5 kHz Channel Spacing, 815.0125 MHz 6B-2: 25 kHz Channel Spacing, 815.0125 MHz 6B-3: 12.5 kHz Channel Spacing, 860.0125 MHz 6B-4: 25 kHz Channel Spacing, 860.0125 MHz 6B-5: 12.5 kHz Channel Spacing, 900.9875 MHz 6B-6: 25 kHz Channel Spacing, 900.9875 MHz 6B-7: 12.5 kHz Channel Spacing, 935.0125 MHz 6B-8: 25 kHz Channel Spacing, 935.0125 MHz EXHIBIT 6C – Audio Low Pass Filter Response 6C-1: 12.5 kHz Channel Spacing, 815.0125 MHz 6C-2: 25 kHz Channel Spacing, 815.0125 MHz 6C-3: 12.5 kHz Channel Spacing, 860.0125 MHz 6C-4: 25 kHz Channel Spacing, 860.0125 MHz 6C-5: 12.5 kHz Channel Spacing, 900.9875 MHz 6C-6: 25 kHz Channel Spacing, 900.9875 MHz 6C-7: 12.5 kHz Channel Spacing, 935.0125 MHz 6C-8: 25 kHz Channel Spacing, 935.0125 MHz EXHIBIT 6D – Modulation Limiting 6D-1: 12.5 kHz Channel Spacing, 815.0125 MHz, Carrier Squelch (CSQ) Mode 6D-2: 12.5 kHz Channel Spacing, 815.0125 MHz TPL, Tone Private Line (TPL) Mode 6D-3: 12.5 kHz Channel Spacing, 815.0125 MHz, Digital Private Line (DPL) Mode 6D-4: 12.5 kHz Channel Spacing, 860.0125 MHz, Carrier Squelch (CSQ) Mode 6D-5: 12.5 kHz Channel Spacing, 860.0125 MHz, Tone Private Line (TPL) Mode 6D-6: 12.5 kHz Channel Spacing, 860.0125 MHz, Digital Private Line (DPL) Mode 6D-7: 12.5 kHz Channel Spacing, 900.9875 MHz, Carrier Squelch (CSQ) Mode 6D-8: 12.5 kHz Channel Spacing, 900.9875 MHz, Tone Private Line (TPL) Mode 6D-9: 12.5 kHz Channel Spacing, 900.9875 MHz, Digital Private Line (DPL) Mode 6D-10: 12.5 kHz Channel Spacing, 935.0125 MHz, Carrier Squelch (CSQ) Mode 6D-11: 12.5 kHz Channel Spacing, 935.0125 MHz, Tone Private Line (TPL) Mode 6D-12: 12.5 kHz Channel Spacing, 935.0125 MHz, Digital Private Line (DPL) Mode 6D-13: 25 kHz Channel Spacing, 815.0125 MHz, Carrier Squelch (CSQ) Mode 6D-14: 25 kHz Channel Spacing, 815.0125 MHz, Tone Private Line (TPL) Mode 6D-15: 25 kHz Channel Spacing, 815.0125 MHz, Digital Private Line (DPL) Mode 6D-16: 25 kHz Channel Spacing, 860.0125 MHz, Carrier Squelch (CSQ) Mode 6D-17: 25 kHz Channel Spacing, 860.0125 MHz, Tone Private Line (TPL) Mode 6D-18: 25 kHz Channel Spacing, 860.0125 MHz, Digital Private Line (DPL) Mode Applicant: Motorola Inc. FCC ID: ABZ99FT5012 EXHIBIT 6 SHEET 2 OF 75 EXHIBIT 6E – Occupied Bandwidth (40 Spectrum Analyzer Plots) 6E-1: 12.5 kHz Channel Spacing, 2500 Hz Audio Modulation Only, 11K0F3E Mask B 6E-2: 12.5 kHz Channel Spacing, 2500 Hz Audio and PL Tone Modulation, 11K0F3E Mask B 6E-3: 12.5 kHz Channel Spacing, 2500 Hz Audio and DPL Tone Modulation, 11K0F3E Mask B 6E-4: 12.5 kHz Channel Spacing, 2500 Hz Audio Modulation Only, 11K0F3E Mask I 6E-5: 12.5 kHz Channel Spacing, 2500 Hz Audio and PL Tone Modulation, 11K0F3E Mask I 6E-6: 12.5 kHz Channel Spacing, 2500 Hz Audio and DPL Tone Modulation, 11K0F3E Mask I 6E-7: 12.5 kHz Channel Spacing, DTMF Modulation Only, 11K0F3E Mask B 6E-8: 12.5 kHz Channel Spacing, DTMF and PL Tone Modulation, 11K0F3E Mask B 6E-9: 12.5 kHz Channel Spacing, DTMF and DPL Tone Modulation, 11K0F3E Mask B 6E-10: 12.5 kHz Channel Spacing, DTMF Modulation Only, 11K0F3E Mask I 6E-11: 12.5 kHz Channel Spacing, DTMF and PL Tone Modulation, 11K0F3E Mask I 6E-12: 12.5 kHz Channel Spacing, DTMF and DPL Tone Modulation, 11K0F3E Mask I 6E-13: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data Modulation Only, 11K0F3E Mask B 6E-14: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data and PL Tone Modulation, 11K0F3E Mask B 6E-15: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data and DPL Tone Modulation, 11K0F3E Mask B 6E-16: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data Modulation Only, 11K0F3E Mask I 6E-17: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data and PL Tone Modulation, 11K0F3E Mask I 6E-18: 12.5 kHz Channel Spacing, 2000/3000 Hz FSK Data and DPL Tone Modulation, 11K0F3E Mask I 6E-19: 25 kHz Channel Spacing, 2500 Hz Audio Modulation Only, 16K0F3E Mask B 6E-20: 25 kHz Channel Spacing, 2500 Hz Audio and PL Tone Modulation, 16K0F3E Mask B 6E-21: 25 kHz Channel Spacing, 2500 Hz Audio and DPL Tone Modulation, 16K0F3E Mask B 6E-22: 25 kHz Channel Spacing, DTMF Modulation Only, 16K0F3E Mask B 6E-23: 25 kHz Channel Spacing, DTMF and PL Tone Modulation, 16K0F3E Mask B 6E-24: 25 kHz Channel Spacing, DTMF and DPL Tone Modulation, 16K0F3E Mask B 6E-25: 25 kHz Channel Spacing, 2000/3000 Hz FSK Data Modulation Only, 16K0F3E Mask B 6E-26: 25 kHz Channel Spacing, 2000/3000 Hz FSK Data and PL Tone Modulation, 16K0F3E Mask B 6E-27: 25 kHz Channel Spacing, 2000/3000 Hz FSK Data and DPL Tone Modulation, 16K0F3E Mask B 6E-28: O.153 Test Pattern 4FSK Voice and Data Modulation, 7K60FXE Mask D 6E-29: O.153 Test Pattern 4FSK Data Modulation Only, 7K60FXD Mask D 6E-30: O.153 Test Pattern 4FSK Voice and Data Modulation, 7K60FXE Mask J 6E-31: O.153 Test Pattern 4FSK Data Modulation Only, 7K60FXD Mask J 6E-32: O.153 Test Pattern 4FSK Voice and Data Modulation, 7K60FXE Mask 24.133 6E-33: O.153 Test Pattern 4FSK Data Modulation Only, 7K60FXD Mask 24.133 6E-34: APCO25 Digital Data, 8K10F1D Mask D 6E-35: APCO25 Digital Voice, 8K10F1E Mask D 6E-36: APCO25 Digital Data, 8K10F1D Mask J 6E-37: APCO25 Digital Voice, 8K10F1E Mask J 6E…

Text truncated - open the document above for the full version.