ABZ99FT5013800/900 Portable Radio

English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A. *6881095C98* 6881095C98-G *NNTN7223C* NNTN7223C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2007 – 2011 Motorola Solutions, Inc. All rights reserved. ATTENTION! 6881095C98-G.book Page 1 Tuesday, December 6, 2011 1:42 PM 2 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. 6881095C98-G.book Page 2 Tuesday, December 6, 2011 1:42 PM 3 English Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits: http://www.fcc.gov/oet/rfsafety/rf-faqs.html www.who.int/en/ www.motorolasolutions.com/rfhealth Federal Communication Commission (FCC) Regulations When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is approved for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 6881095C98-G.book Page 3 Tuesday, December 6, 2011 1:42 PM 4 English NOTE:The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. & FCC, OET Bulletin 65 • Institute of Electrical and Electronic Engineers (IEEE) C95.1 • International Commission on Non-Ionizing Radiation Protection (ICNIRP) • Ministry of Health (Canada) Safety Code 6 & Industry Canada RSS-102 • Australian Communications Authority Radiocommunications Standard et seq. • ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions for Two-Way Radio Operations To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. • DO NOT remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. 6881095C98-G.book Page 4 Tuesday, December 6, 2011 1:42 PM 5 English Two-Way Radio Operation • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). • Private Talk Position (XTS 4000 Only). When placing or receiving a personal message, hold your radio as you would a wireline/wireless telephone. Speak directly into the microphone. Use the PTT as in a normal two-…

Text truncated - open the document above for the full version.

PROFESSIONAL DIGITAL TWO-WAY RADIO & SMARTNET® AND SMARTZONE PORTABLE RADIOS MOTOTRBO™ XPR™ 6580 IS DISPL AY POR TA BL E USER GUIDE _Blank.fm Page 1 Friday, November 4, 2011 2:24 PM Declaration of Conformity English i Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola Solutions, Inc.Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.Phone Number: 1-800-927-2744Hereby declares that the product: Model Name: XPR 6580 IS conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital DeviceAs a personal computer peripheral, this device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity English ii Note: This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wi ll not occur in a particular installation. If this equipment does cause harmful interference to radi o or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. • Consult the dealer or an experienc ed radio/TV technician for help. Contents English iii ContentsThis User Guide contains all the information you need to use the MOTOTRBO XPR IS Series Portable Radios.Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . iImportant Safety Information . . . . . . . . . . . . . . . . . vi Product Safety and RF Exposure Compliance . . .vi Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . viComputer Software Copyrights . . . . . . . . . . . . . . . vii Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiiGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . 1What Your Dealer/System Administrator Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Preparing Your Radio for Use . . . . . . . . . . . . . . . . . . 2 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 2 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . 3Attaching the Univer sal Connector Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 4Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5 Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 5 Radio Controls You Will Be Using . . . . . . . . . . . . . . 6Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7 Assignable Radio Functions . . . . . . . . . . . . . . . . . 7Assignable Settings or Utility Functions . . . . . . . . . 8 Accessing the Programmed Functions . . . . . . . . . . . 8Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Push-To-Talk (PTT) Bu tton . . . . . . . . . . . . . . . . . . . 10 Switching Between Conventional and Trunking Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Identifying Status Indicators . . . . . . . . . . . . . . . . . . 11 Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Main Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12In-Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Making and Receiving Calls . . . . . . . . . . . . . . . . . . 14 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 15Receiving and Responding to a Radio Call . . . . . . 15 Receiving and Responding to a Group Call . . . . . 15Receiving and Responding to a Private Call . . . . 16 Receiving and Responding to a Phone Call . . . . 17 Contents English iv Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 17 Making a Call with the Channel Selector Knob . . 18 Making a Group Call . . . . . . . . . . . . . . . . . . . . 18Making a Private Call . . . . . . . . . . . . . . . . . . . . 18Making an Enhanced Private Call . . . . . . . . . . 19Making a Phone Call . . . . . . . . . . . . . . . . . . . . 20Sending a Status Call . . . . . . . . . . . . . . . . . . . 20Using the Dynamic Regrouping Feature . . . . . 21 Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 23 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . 23Permanent Monitor . . . . . . .…

Text truncated - open the document above for the full version.

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 2 SHEET 1 OF 1 EXHIBIT 2 STATEMENT OF CERTIFICATION - Pursuant to 47 CFR 2.907 The technical data supplied with this application, having been taken under my supervision is hereby duly certified. The following is a statement of my qualifications: 1) I received an Electrical and Electronic Engineering degree from National University of Malaysia. 2) I have 8 years experience in developing, testing, and certifying Portable Communications Products. NAME: Yap Soon Leng SIGNATURE: DATE: January 15, 2012 POSITION: Electrical Engineer 3) I hereby certify that the above application was prepared under my direction and that to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. NAME: Lee Szu See SIGNATURE: DATE: January 15, 2012 POSITION: Engineering Section Manager

FCC ID: ABZ99FT5013 EXHIBITS 13B ______________________________________________________________________________ Motorola Solutions Inc. 1301 E. Algonquin Rd., Schaumburg, IL 60196 CONFIDENTIALITY REQUEST February 3, 2012 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: ABZ99FT5013 Dear Sir/Madam: Motorola Solutions is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Transmitter Description) not be made routinely available for public inspection. Motorola considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as “Confidential”. Please contact me if you require any additional information. Sincerely, Larry D. Larsen Regulatory Coordinator Email: [email protected]

Date: February 08, 2012 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Letter of Authorization for FCC ID ABZ99FT5013 Dear Sir or Madam: This letter is to authorize Larry D. Larsen to sign Form 731 applications on my behalf for the subject FCC ID Filing. Please contact me if there are any questions or issues. Sincerely, Ken Weiss Senior Staff Engineer Tel: (847)‐576‐2789 Fax: (847)‐538‐3905 E‐mail: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 1 OF 7 EXHIBIT 3 EXTERNAL PHOTOGRAPHS - Pursuant to 47 CFR 2.1033(c) 12 FIGURE 3-1: FRONT VIEW OF PORTABLE RADIO - FULL DISPLAY AND KEYPAD MODEL Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 2 OF 7 FIGURE 3- 2: BACK VIEW OF PORTABLE RADIO Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 3 OF 7 FIGURE 3-3: LEFT SIDE (PTT) OF THE PORTABLE RADIO Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 4 OF 7 FIGURE 3-4: RIGHT SIDE OF THE PORTABLE RADIO Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 5 OF 7 FIGURE 3-5: FCC AND SAFETY LABELS LOCATION OF PORTABLE RADIO FCC Label Location Safety Label Location Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 6 OF 7 FIGURE 3-6: CLOSE UP VIEW OF THE SAFETY LABEL. FIGURE 3-7: IECEx/CSA PORTABLE RADIO BATTERY NO Kit NUMBER BATTERY TYPE 1. NNTN8287A Li-Ion 1750mAH Impres Battery Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 3 SHEET 7 OF 7 FIGURE 3-8: PORTABLE RADIO ANTENNAS NO ATTENNA TYPE COLOUR LENGTH 1. Whip (MOTOTRBO Blue 800/900 GPS Whip Antenna 806-941 MHz) 18 cm

Applicant: Motorola Solutions Inc FCC ID: ABZ99FT5013 EXHIBIT 1 SHEET 1 OF 1 EXHIBIT 1 IDENTIFICATION LABEL LOCATION See the Attached Photograph or Sketch Top of Radio X Back of Radio under Belt Clip Back of Radio TYPE X sensitive adhesive backing. The adhesive is a permanent type acrylic The label is a polyester film laminate with a pressure with the minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X Label Attached Below. See the Attached Photograph and Exhibit 3 for the actual location of the FCC label on the device. See Attached Drawing. Figure 1-1: FCC Label

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 9 SHEET 1 OF 5 EXHIBIT 9 INTERNAL PHOTOGRAPHS – PURSUANT 47 CFR 2.1033 (C) 12 FIGURE 3- 1: NEO CSA COMPLETE INTERNAL OPEN UP VIEW. Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 9 SHEET 2 OF 5 FIGURE 3- 2: NEO CSA WITH OPTION BOARD. Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 9 SHEET 3 OF 5 FIGURE 3- 3: NEO CSA WITH OPTION BOARD WITHOUT SHIELDS (TOP SIDE) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 9 SHEET 4 OF 5 FIGURE 3- 4: NEO CSA WITH OPTION BOARD WITHOUT SHIELDS (BOTTOM SIDE) Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 9 SHEET 5 OF 5 FIGURE 3-5: NEO CSA CHASSIS, BOARD AND CAN SHIELDS

SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 1 of 49 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 1 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 01/04/2012 Report Revision: O Report ID: SAR rpt_PMUF1473B_Rev.O _120104_SR9992 Responsible Engineer: Veeramani Veerapan (Sr. EME Engineer) Report Author: Veeramani Veerapan (Sr. EME Engineer) Date/s Tested: 11/21/2011 –12/8/2011 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 11/14/2011 DUT Description: 806-870 MHz & 896-941 MHz, 12.5kHz/25kHz, 2W, 160CH, FKP & Display with GPS (Capable of analog FM transmission and digital TDMA transmission.) Test TX mode(s): CW (PTT) Max. Power output: 2.65 Watts Nominal Power: 2.20 Watts Tx Frequency Bands: TMO: 806-825 MHz, DMO: 851-870 MHz (800 band) & TMO: 896-902 MHz, DMO: 935-941 MHz (900 band) Signaling type: FM and TDMA Model(s) Tested: PMUF1473B Model(s) Certified: PMUF1473B Serial Number(s): N4RPRD1O, N4RPRD1P Classification: Occupational/Controlled FCC ID: ABZ99FT5013; Rule part 90 (806-824, 851-869, 896-901 & 935-940 MHz) IC: 109AB-99FT5013 (806-821, 821-824, 851-866, 866-869, 896-901 & 935-940 MHz) * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc, Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 1/19/2012 Certification Date: 1/19/2012 Certification No.: L1120111P SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 2 of 49 Part 1 of 2 1.0 Introduction ..............................................................................................................4 2.0 Abbreviations / Definitions ......................................................................................4 3.0 Referenced Standards and Guidelines ......................................................................4 4.0 SAR Limits ..............................................................................................................5 5.0 SAR Result Scaling Methodology ...........................................................................6 6.0 Description of Device Under Test (DUT) ................................................................6 7.0 Optional Accessories and Test Criteria ....................................................................7 7.1 Battery ..........................................................................................................7 7.2 Antenna ........................................................................................................7 7.3 Body worn Accessories .............................................................8 7.4 Audio Accessories ...................................................................8 8.0 Description of Test System ......................................................................................9 8.1 Descriptions of Robotics/Probes/Readout Electronics ................................9 8.2 Description of Phantom(s) ...........................................................................9 8.2.1 Dual Flat Phantom ...........................................................................9 8.2.2 SAM Phantom ..................................................................................9 8.2.3 Elliptical Flat Phantom ....................................................................9 8.3 Description of Simulated Tissue ................................................................10 9.0 Additional Test Equipment ....................................................................................11 10.0 SAR Measurement System Verification ................................................................12 10.1 Equivalent Tissue Test Results ..................................................................12 10.2 System Check Test Results ........................................................................14 11.0 Environmental Test Conditions .............................................................................14 12.0 DUT Test Methodology .........................................................................................14 12.1 Measurements ............................................................................................14 12.2 DUT Configuration(s) ................................................................................15 12.3 DUT Positioning Procedures ....................................................................15 12.3.1 Body ............................................................................................15 12.3.2 He…

Text truncated - open the document above for the full version.

SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 1 of 42 TESTING CERT # 2518.05 DECLARATION OF COMPLIANCE SAR ASSESSMENT Part 2 of 2 Enterprise Mobility Solutions EME Test Laboratory Motorola Solutions Malaysia Sdn Bhd (455657-H) Customer Solution Center Plot 2, Bayan Lepas Technoplex Industrial Park, Mukim 12 SWD 11900 Bayan Lepas Penang, Malaysia. Date of Report: 01/04/2012 Report Revision: O Report ID: SAR rpt_PMUF1473B_Rev.O _120104_SR9992 Responsible Engineer: Veeramani Veerapan (Sr. EME Engineer) Report Author: Veeramani Veerapan (Sr. EME Engineer) Date/s Tested: 11/21/2011 –12/8/2011 Manufacturer/Location: Motorola, Penang Sector/Group/Div.: EMS Date submitted for test: 11/14/2011 DUT Description: 806-870 MHz & 896-941 MHz, 12.5kHz/25kHz, 2W, 160CH, FKP & Display with GPS (Capable of analog FM transmission and digital TDMA transmission.) Test TX mode(s): CW (PTT) Max. Power output: 2.65 Watts Nominal Power: 2.20 Watts Tx Frequency Bands: TMO: 806-825 MHz, DMO: 851-870 MHz (800 band) & TMO: 896-902 MHz, DMO: 935-941 MHz (900 band) Signaling type: FM and TDMA Model(s) Tested: PMUF1473B Model(s) Certified: PMUF1473B Serial Number(s): N4RPRD1O, N4RPRD1P Classification: Occupational/Controlled FCC ID: ABZ99FT5013; Rule part 90 (806-824, 851-869, 896-901 & 935-940 MHz) IC: 109AB-99FT5013 (806-821, 821-824, 851-866, 866-869, 896-901 & 935-940 MHz) * Refer to section 15 of part 1 for highest SAR summary results. The test results clearly demonstrate compliance with FCC Occupational/Controlled RF Exposure limits of 8 W/kg averaged over 1 gram per the requirements of 47 CFR 2.1093(d). The 10 grams result is not applicable to FCC filing. The test results clearly demonstrate compliance with ICNIRP (1998) Guidelines for limiting exposure in time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz), Health Physics 74, 494-522 RF Exposure limits of 10 W/kg averaged over 10grams of contiguous tissue. Based on the information and the testing results provided herein, the undersigned certifies that when used as stated in the operating instructions supplied, said product complies with the national and international reference standards and guidelines listed in section 3.0 of this report. This report shall not be reproduced without written approval from an officially designated representative of the Motorola Solutions Inc, Laboratory. I attest to the accuracy of the data and assume full responsibility for the completeness of these measurements. This reporting format is consistent with the suggested guidelines of the TIA TSB-150 December 2004. The results and statements contained in this report pertain only to the device(s) evaluated. Deanna Zakharia EMS EME Lab Senior Resource Manager, Laboratory Director Approval Date: 1/19/2012 Certification Date: 1/19/2012 Certification No.: L1120111P SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 2 of 42 Appendix D Test System Verification Scans The SAR result indicated on the Manufacture’s Calibrated certificates for dipole D900V2 S/N 1d025 was not used due to the following: -- The IEEE 1528-2003 and the FCC OET-65 Supplement C, System Verification section indicated that “The measured 1-g SAR should be within 10% of the expected target values specified for the specific phantom and RF source used in the system verification measurement.” -- SPEAG calibration certificate indicates that the allowed tolerance for this dipole is higher than +/-10% (e.g. 11.4 +/-17.0 % at k=2 for the D900V2 S/N 1d025). -- The allowed tolerance for the probe is also higher than +/- 10% (e.g. 12.0 % at k=2 at 900 MHz for the probe being used to assess this product). Due to probe, dipole and system tolerances noted above, the lab averages dipole results across multiple probes to establish a set of averaged targets for each dipole using the following procedure: • The System Validation was conducted per IEEE1528-2003 and IEC62209-2 Edition 1.0 2010-03 standards using the simulated head tissue and multiple probes that are available and applicable for the dipole under test to verify the System Validation. Results for this dipole are within the measurement system uncertainty of the reference SAR values indicated within IEC62209-2 Edition 1.0 2010-03 when using a flat phantom with 2mm thickness. These results then are averaged and used as the target for the daily system performance check when the simulated head tissue is used. • The dipole targets for the body are set immediately following the same process noted above. Since there is no standard referencing the SAR values for the System Validation using the simulated body tissue, the compliant System Validation results using the simulated head tissue are used to justify the use of the System Validation results using the simulated body tissue due to the same setup except for the simulated tissue type. The targets set in this report were conducted following the above process. Note that the targets set for the tested dipole, when using the simulated head tissue, meets the requirement for the system validation per IEEE1528-2003, IEC62209-2 Edition 1.0 2010-03 standards, and the difference between this result and the result from the manufacture’s dipole calibration certificate is up to 10.2 % for the 900 MHz which are well within the measurement uncertainty of the measurement system at k=2. To assess the isotropic characteristics of the measurement probe, a probe rotation was performed using the "Rotation (1D)" function in the DASY software with a measured isotropy tolerance of +/- 0.5dB. SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 3 of 42 SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 4 of 42 SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 5 of 42 SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 6 of 42 SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 7 of 42 SR9992 Motorola Solutions EME Form-SAR-Rpt-Rev. 11.0 Page 8 of 42 SR9992 Motorola Solutions EME Form-SAR…

Text truncated - open the document above for the full version.

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT5013 EXHIBIT 6 SHEET 1 OF 76 EXHIBIT 6 INDEX OF SUBMITTED MEASURED DATA This exhibit contains the measured data for this equipment as follows: EXHIBIT 6A – RF Power Output EXHIBIT 6B – Audio Frequency Response 6B-1: 12.5 kHz Channel Spacing, 815.0125 MHz 6B-2: 25 kHz Channel Spacing, 815.0125 MHz 6B-3: 12.5 kHz Channel Spacing, 860.0125 MHz 6B-4: 25 kHz Channel Spacing, 860.0125 MHz 6B-5: 12.5 kHz Channel Spacing, 900.9875 MHz 6B-6: 25 kHz Channel Spacing, 900.9875 MHz 6B-7: 12.5 kHz Channel Spacing, 935.0125 MHz 6B-8: 25 kHz Channel Spacing, 935.0125 MHz EXHIBIT 6C – Audio Low Pass Filter Response 6C-1: 12.5 kHz Channel Spacing, 815.0125 MHz 6C-2: 25 kHz Channel Spacing, 815.0125 MHz 6C-3: 12.5 kHz Channel Spacing, 860.0125 MHz 6C-4: 25 kHz Channel Spacing, 860.0125 MHz 6C-5: 12.5 kHz Channel Spacing, 900.9875 MHz 6C-6: 25 kHz Channel Spacing, 900.9875 MHz 6C-7: 12.5 kHz Channel Spacing, 9…

Text truncated - open the document above for the full version.