ABZ99FT7016Part 15 Transmitter

m Bluetooth ® Accessory Pod PMLN6396/HKLN4512 BLUETOOTH ACCESSORY POD PMLN6396/ HKLN4512 Congratulations on your new Motorola Bluetooth Accessory Pod! This Pod device is designed to allow you the convenience of Bluet ooth technology by simply connecting it to a Motorola swivel earpiece, enabling you to comfortably wear it in many convenient ways for long periods of time. Furthermore, the Bluetooth Pod is exclusively designed for busi ness radio applications and optimized to work with Motorola two-way radios. This user guide contains the operation and pairing instructions of Bluetooth Pod. Before getting started, please make sure you read and understand the RF and Acoustic Safety sections, wh ich contain very important information about this product. FOREWORD Product Safety and RF Exposure Compliance ATTENTION! The radio is restricted to o ccupational use only to satisfy ICNIRP/FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the RF Energy Exposure and Product Safety Guide booklet enclosed with your radio (Motorol a Publication part number 6881095C98 (US) or 6864117B25 (EMEA)) to ensure compliance with RF energy exposure limits.This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard (s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Motorola may void the user’s authority to operate this device. Battery Information: Battery is shipped with a nominal charge between 30% and 50%. Battery should be stored between -10 °C (14 °F) and 30 °C (86 °F) to minimize permanent capacity loss.Caution : Storing your fully charged accessory in high-temperature conditions may permanently reduce the life of the internal battery. Note : The battery is not a user replaceable part. Important Information: • Do not charge your accessory in temperatures below 0 °C (32 °F) or above 45 °C (113 °F). Do not store your accessory in direct sunlight or where expected temperatures can exceed this range such as inside a parked car. • Storing your fully charged accessory in high-temperature conditions may permanently reduce the life of the internal battery. • Battery life may temporarily shorten in low-temperature conditions. ACOUSTIC SAFETY Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.To protect your hearing:• Use the lowest volume necessary to do your job. • Turn up the volume only if you are in noisy surroundings. • Turn down the volume before adding headset or earpiece. • Limit the amount of time you use headsets or earpieces at high volume. GETTING STARTED Before you start, make sure the pod is fully charged. Recommended charging time is three (3) hours.For detailed instructions on pod charging, please refer to the Charging Cradle Instructions Leaflet (P/N: 68012008029). BLUETOOTH ACCESSORY POD OVERVIEW This Bluetooth Accessory Pod is designed to be used in conjunction with the Motorola Earpiece PMLN6397/HKLN4513 as shown in the figure below: Before using this product, read the operating instructions for safe usage contained in the RF Energy Exposure and Product Safety Guide enclosed with your radio. ! C a u t i o n In order to connect the Swivel Earpiece, insert the earpiece audio connector into the pod audio jack connector, making sure it is firmly attached.Note: Power ON the pod only after the earpiece is inserted. PAIRING THE POD WITH YOUR TWO-WAY RADIO Pairing your pod for the first time1. Before starting, make sure your two-way radio is in pairing mode. 2. With the pod off, press and hold the pod power button until the LED is solid Blue. 3. Position the pod next to the two-way radio that you want to pair. 4. Pod will provide voice prompt to indicate successful connection. 5. Refer to the table below for additional LED status indications. Clearing/Erasing Pairing Information1. Ensure the previous connected two-way radio is turned off. 2. Turn off the pod. 3. Long press the power button until you hear a voice prompt “Pairing Cleared”. 4. LED will show solid Blue, indicating the pod is in pairing mode. For more information about th is product, please contact your Motorola Authorized Dealer or visit us at: http://www.motorola.com/Business/US-EN/ Business+Product+and+Services/Accessories/Two-Way+Radio+Accessories/Wireless+Bluetooth+Accessories BLUETOOTH POD STATUS AND LED INDICATORS CHARGING YOUR DEVICE The pod can be charged with Motorola Bluetooth Pod Charging Cradle (PMLN6428/HKLN4509).Note : For assuring proper operation, DO NOT power on the pod while charging. Swivel Earpiece Bluetooth Pod 1 2 3 4 6 5 Number Indication 1 3.5 mm Audio Jack 2 Bluetooth Status Indicator 3 Power Button 4 Clip 5 Recess for Label 6 Charger Contact State LED Indication Power Power ON (LED ON) (press and hold for 1 second) Solid Green LED for 3 seconds then OFF Power OFF (Press and hold for 3 seconds) Flashing Red LED 3 times then OFF BT Status Pairing Mode Solid Blue LED BT Connecting Flashing Green LED Pairing Fail/Timeout Flashing Purple LED for 2 seconds Wireless Link Connected With Host Flashing Blue LED every 5 seconds Wireless Link Disconnected From Host Fast Flashing Blue LED Battery Low Flashing Red LED every 2 minutes Charging Charging Solid Red LED Fully Charged Solid Green LED MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 20…

Text truncated - open the document above for the full version.

Date: November 27, 2012 Certification Department Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Subject: Letter of Authorization for the following filing packages: FCC ID: ABZ99FT4016 IC ID: 109AB-99FT4016 This letter is to authorize Larry D. Larsen to sign application forms and associated documentation on my behalf for the subject filing. Please contact me if there are any questions or issues. Sincerely, Ken Weiss Senior Staff Engineer Tel: (847)-576-2789 Fax: (847)-538-3905 E-mail: [email protected]

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 3 SHEET 1 OF 5 EXHIBIT 3 The following photographs are attached. Exhibit 1. Front view 3A 2. Back View (FCC label location) 3B 3. Top View 3C 4. Bottom View 3D 5. Side View (left) 3E 6. Side View (right) 3F 7. Unit with Earpiece 3G 8. Unit with Charger 3H Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 3 SHEET 2 OF 5 Front VIEW Exhibit 3A (FCC label under the clip) Back VIEW (with Clip) Exhibit 3B Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 3 SHEET 3 OF 5 Top VIEW Exhibit 3C Bottom VIEW Exhibit 3D Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 3 SHEET 4 OF 5 Side VIEW (left) Exhibit 3E Side VIEW (right) Exhibit 3F Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 3 SHEET 5 OF 5 Unit with Earpiece Exhibit 3G Unit with Charger Exhibit 3H

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016/IC:109AB-99FT7016 EXHIBIT 1 SHEET 1 OF 1 Identification Label LOCATION X See the Attached Photograph or Sketch _ Back of Radio Back of Radio under Belt Clip TYPE X The label is a paper polyester film laminate with a pressure Sensitive adhesive backing. The adhesive is a permanent type acrylic with minimum peel strength of 40 oz/inch. MARKINGS (TEXT) X See the Attached Photograph and Exhibit 3C for the actual location of the FCC label on the device. Label Attached Below. See Attached Drawing . FCC IC Label

Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 9 SHEET 1 OF 2 Confidentiality Requested EXHIBIT 9 Internal Photographs The following photographs are attached. Exhibit 1. PCB Top layer outside housing 9A 2. PCB Bottom layer inside housing 9B Applicant: Motorola Solutions Inc. FCC ID: ABZ99FT7016 / IC: 109AB-99FT7016 EXHIBIT 9 SHEET 2 OF 2 Confidentiality Requested EXHIBIT 9A - PCB Top layer outside housing EXHIBIT 9B - PCB Bottom layer inside housing Bluetooth antenna

Engineering Test Report No. 1203286-01 Measurement of RF Emissions from a Model PMLN6396A Transceiver For Motorola, Inc. 1301 E. Algonquin Road Schaumburg, IL 60196 P.O. Number NP5534152 Date Tested October 24, 2012 through November 6, 2012 Test Personnel Mark E. Longinotti, Ian Carnegie Test Specification FCC "Code of Federal Regulations" Title 47, Part 15, Subpart C, Sections 15.247 for Frequency Hopping Spread Spectrum Intentional Radiators Operating within the band 2400-2483.5MHz Industry Canada RSS-GEN Industry Canada RSS-210 Test Report By: Mark E. Longinotti EMC Engineer Requested By: Larry Larsen Motorola, Inc. Approved By: Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1203286-01 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 68 1 Introduction ................................................................................................................................................... 5 1.1 Scope of Tests ..................................................................................................................................... 5 1.2 Purpose ............................................................................................................................................... 5 1.3 Deviations, Additions and Exclusions .................................................................................................. 5 1.4 EMC Laboratory Identification ............................................................................................................. 5 1.5 Laboratory Conditions.......................................................................................................................... 5 2 Applicable Documents .................................................................................................................................. 5 3 EUT Setup and Operation ............................................................................................................................ 6 3.1 General Description ............................................................................................................................. 6 3.1.1 Power Input ..................................................................................................................................... 6 3.1.2 Peripheral Equipment ...................................................................................................................... 6 3.1.3 Signal Input/Output Leads ............................................................................................................... 6 3.1.4 Grounding ........................................................................................................................................ 6 3.2 Operational Mode ................................................................................................................................ 6 3.3 EUT Modifications ................................................................................................................................ 6 4 Test Facility and Test Instrumentation ......................................................................................................... 6 4.1 Shielded Enclosure .............................................................................................................................. 6 4.2 Test Instrumentation ............................................................................................................................ 6 4.3 Calibration Traceability ........................................................................................................................ 6 4.4 Measurement Uncertainty ................................................................................................................... 7 5 Test Procedures ........................................................................................................................................... 7 5.1 Transmitter ........................................................................................................................................... 7 5.1.1 20dB Bandwidth .............................................................................................................................. 7 5.1.1.1 Requirement ........................................................................................................................... 7 5.1.1.2 Procedures ............................................................................................................................. 7 5.1.1.3 Results .................................................................................................................................... 8 5.1.2 Carrier Frequency Separation ......................................................................................................... 8 5.1.2.1 Requirements ......................................................................................................................... 8 5.1.2.2 Procedures ............................................................................................................................. 8 5.1.2.3 Results .................................................................................................................................... 8 5.1.3 Number of Hopping Frequencies .................................................................................................... 8 5.1.3.1 Requirements ......................................................................................................................... 8 5.1.3.2 Procedures ..........................................................................…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1203286-01 Page 18 of 68 Figure 2 Test Setup for Radiated Emissions, below 2GHz – Horizontal Polarization Test Setup for Radiated Emissions, below 2GHz – Vertical Polarization Engineering Test Report No. 1203286-01 Page 19 of 68 Figure 3 Test Setup for Radiated Emissions, 2GHz to 18GHz – Horizontal Polarization Test Setup for Radiated Emissions, 2GHz to 18GHz – Vertical Polarization Engineering Test Report No. 1203286-01 Page 20 of 68 Figure 4 Test Setup for Radiated Emissions, above 18GHz – Horizontal Polarization Test Setup for Radiated Emissions, above 18GHz – Vertical Polarization