ACEPAL101V1Mobile phone

Use manual We reserve the right to upgrade the software and product without prior notice. The icon in this user manual may differ from your phone, depending on the phone you used. We reserve the right to make changes to this user manual without prior notice. All rights reserved. Safety Instruction Please read below detail instructions carefully. It may have danger or illegality if you do not follow these instructions. Receiver LCD Up key Direct Number speed dial End key/power key # key Answer key Down key Number keys * key LED This user manual includes detail information about safety instruction. Switch on Phone Safely Please do not switch on your phone when it might have interference or danger by using phone or phone is forbidden in this area. Pay attention to the traffic safety According to the recent research, it may have danger to use phone when you are driving even though you are using the hands-free device (such as hands-free device in auto, earphone, etc.). The driver is required not to use phone when they are driving. When phone is switched on, the electromagnetic wave from phone will interference the electronic system of auto, such as ABS anti-explosion brake system or SRS (supplemental restraint system). For safety, please follow below: - Do not put the phone on car control panel or ballonet area in car. - Confirm with the auto distributor or manufacturer to make sure that electronic system of automatics have good isolation. Interference All kinds of phones may be interfered by environment, and then the performance of phones might be influenced. Phone may interfere with some electric appliance such as electronic TV, radiogram, PC and so on. Turn off your cell phone in the site of medical and health care Please switch off your phone in the site of medical and health care except some designated area where phone can be used. Phone will interfere with the running of electronic equipment, electron device or radio frequency device near around, just like the other usual equipment. Switch off on airplane Please follow the related regulations. Please switch your phone before boarding. Switch off in gas station Please switch off your phone when you are in gas station or any position where fuel and chemical have been placed. Cell phone should be turned off around the site of explode .To avoid the interference to exploding, please switch off your phone when you see the mark of “site of explode” or “turn off bidirectional radio devices”. Please abide any related forbidden regulation, and execute any regular or statute which related with cell phone’s using. Using phone correctly Please use phone in normal position. Please do not touch antenna area if not necessary. Do not let children use phone without any tendance. SIM card can be taken out from phone. Please pay attention to prevent children from swallow the small component like this. Do not let pregnant woman use phone for long time. Accessories and batteries Use only the approved accessories and batteries. Please do not connect with any product which doesn’t match with this phone. Please be sure the phone has been switched off before taking out battery. Please deal with the scrap batteries properly according to the local status. Waterproof The phone doesn’t have performance of waterproof. Please do not expose your phone in inclement weather or environment (such as wet, raining, liquid leakage, seawater, mirage, and so on). Emergency calling Please be sure your phone is power on and in the service available area. According to demands, press end key repeatedly to clear the content in screen and go back to standby mode, or press number key directly, then input emergency phone number. And then press answer key to describe where you are. Please do not hang up your phone without permission. Switch On / Off Phone Switch On Long press to switch on. If you already set the PIN code ON, then you need to type in PIN code. Type in the code and press green key to enter. Then phone will be on. ( Default PIN code is 1122） Warning：SIM card will be locked if you type wrong code for three times. And it will inform you to type in PUK code. (Please contact your network service vendor to unlock it if needed.） Switch Off Long press to switch off the phone at standby mode. Stand by Mode When phone is ready to use but no operation is done on phone, then phone is under stand by mode. Tone Volu me - Boost key Volume + Volume - Tone Volu me + SOS key Press enter to phonebook long press to power on/power off Press enter to PhonebookPress enter to Main menu Long press to power on / off Press enter to calendar Press enter to user profiles Answer key Press enter to Direct number speed dial Key Functions Answer Key (Green key) Press to call out: press to pick up phone when there is incoming call. Standby mode：press to enter call list End Key(Red key) Phone Off：Long press to switch on; Phone On：Long press to switch off; Long press it at non-editing screen to go back to standby Navigation Key(Up key) Standby mode：press to enter use calendar Operating：press to move cursor up Navigation Key(Down key) Standby mode：press to enter use profiles Operating：press to move cursor down M1 Standby mode: short press to enter main menu Standby mode: long press to speed dial Operating：press to confirm the function you choose. M2 Standby mode: long press to speed dial Calculator: press to divide M3 Standby mode: short press to enter phonebook Standby mode: long press to speed dial Operating：press to go back to previous menu # KEY Standby mode: Long press: to lock or unlock the key; Short press: to enter # Editing mode: press to switch input method *KEY Standby mode ： Long press :to switch silent/general mode; Short press: to enter *，P，+. BOOST key Standby mode: press to switch activated/deactivated boost, very loud volume. Volume key Standby mode: Press +: to increase key tone volume Press -: to decrease key tone volume Talking mode: adjust the volume of calls Tone key Press to switch the…

Text truncated - open the document above for the full version.

Clarity, A Division of Plantronics, Inc. 2013-01-06 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Global United Technology Services Co., Ltd..; 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China； Bruce.Zhang, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Clarity, A Division of Plantronics, Inc. 9131 Preservation Drive,Chattanooga TN37406,USA Dated this 2013-01-06 Agency agreement expiration date: 2014-01-06 By: John Lowe Signature Printed Title: Manager On behalf of : Clarity,A Division of Plantronics,Inc. Telephone: 1-800-426-3738

Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 38 of 46 8 EUT Constructional Details Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 39 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 40 of 46

Label and label location

Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 41 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 42 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 43 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 44 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 45 of 46 Report No: GTSE13010000901 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 46 of 46 ------End of report------

GCCT No.121210-R1 Page 1 of 89 SAR TEST REPORT No. 121210-R1 for Clarity, A Division of Plantronics, Inc Mobile phone Model Name: PAL101 Trade Mark: Clarity FCC ID: ACEPAL101V1 Issued Date: 2013-01-22 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of GCCT. Test Laboratory: GCCT, Guangdong Telecommunications Terminal Products Quality Supervision and Testing Center Technology Road, High-tech Zone, He Yuan City, Guang Dong Province, PR China 517001 Tel:+86(0)762-3607139, Fax:+86(0)762-3603336 Email: [email protected]. www.ncct.org.cn GCCT No.121210-R1 Page 2 of 89 TABLE OF CONTENTS 1. General Information.............................................................................................. 4 1.1 Testing Laboratory ...................................................................................... 4 1.2 Application Information ............................................................................... 4 1.3 Manufacturer Information ............................................................................ 4 1.4 EUT Information.......................................................................................... 5 2. EUT Operational Conditions During Test ............................................................. 6 2.1 General Description of Test Procedures..................................................... 6 2.2 GSM Test Configuration ............................................................................. 6 3. SAR Measurements System Configuration .......................................................... 7 3.1 Measurement System Diagram................................................................... 7 3.2 System Components................................................................................... 8 3.3 Equivalent Tissues .................................................................................... 11 4. Evaluation Procedures ....................................................................................... 12 4.1 Data Evaluation......................................................................................... 12 4.2 SAR Evaluation Procedures...................................................................... 13 4.3 Spatial Peak SAR Evaluation.................................................................... 14 5. Test Laboratory Environment............................................................................. 16 6. Conducted Output Power Measurement............................................................ 16 7. SAR Measurement Results ................................................................................ 16 7.1 Liquid Measurement Results..................................................................... 16 7.2 System Performance Check..................................................................... 17 7.3 Measurement Results ............................................................................... 19 8. Measurement Uncertainty .................................................................................. 21 9. EUT Photo.......................................................................................................... 22 10. Equipment List & Calibration Status............................................................. 24 11. Attachments ................................................................................................. 25 ANNEXE 1 System Performance Check Plots......................................................... 26 ANNEXE 2 SAR Test Plots....................................................................................... 30 ANNEXE 3 EUT Test Positions ................................................................................ 53 ANNEXE 4 Probe calibration report.......................................................................... 55 ANNEXE 5 Dipole calibration report......................................................................... 67 ANNEXE 6 DAE calibration report ............................................................................ 84 GCCT No.121210-R1 Page 3 of 89 GENERAL SUMMARY Product Name Mobile phone Model Name PAL101 Applicant Clarity, A Division of Plantronics, Inc Manufacturer Primatronix (Nanho) Electronics Ltd. Test laboratory GCCT, Guangdong Telecommunications Terminal Products Quality Supervision and Testing Center Reference Standards OET Bulletin 65 (Edition 97-01) and Supplement C (Edition 01-01): Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE 1528-2003: Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques FCC KDB 447498 D01 v05: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies FCC KDB 865664 D01 v01: SAR Measurement Requirements for 100 MHz to 6 GHz IEC 62209-1: 2006 : Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Human models, instrumentation, and procedures, Part 1: Procedure to determine the specific absorption rate (SAR) for hand-held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz) IEC 62209-2: 2010: Human exposure to radio frequency fields from handheld and body-mounted wireless communication devices - Human models, instrumentation, and procedures, Part 2: Procedure to determine the specific absorption rate (SAR) for mobile wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) Test Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards…

Text truncated - open the document above for the full version.

Global United Technology Service Co., Ltd. Report No: GTSE13010000902 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC REPORT (Bluetooth) Applicant: Clarity,A Division of Plantronics,Inc. Address of Applicant: 9131 Preservation Drive, Chattanooga, Tennessee, United States Equipment Under Test (EUT) Product Name: Mobile Phone Model No.: PAL101 FCC ID: ACEPAL101V1 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247:2011 Date of sample receipt: 24 Dec., 2012 Date of Test: 26 to 29 Dec., 2012 Date of report issued: 04 Jan., 2013 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No: GTSE13010000902 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 37 2 Version Version No. Date Description 00 04 Jan., 2013 Original Prepared By: Date: 04 Jan., 2013 Report Clerk Check By: Date: 04 Jan., 2013 Project Engineer Report No: GTSE13010000902 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 37 2 Contents Page 1 COVER PAGE.............................................................................................................................................................. 1 2 VERSION....................................................................................................................................................................... 2 2 CONTENTS................................................................................................................................................................... 3 3 TEST SUMMARY......................................................................................................................................................... 4 4 GENERAL INFORMATION........................................................................................................................................ 5 4.1 CLIENT INFORMATION................................................................................................................................................. 5 4.2 GENERAL DESCRIPTION OF E.U.T. .............................................................................................................................. 5 4.3 TEST MODE.................................................................................................................................................................. 7 4.4 TEST FACILITY............................................................................................................................................................ 7 4.5 TEST LOCATION.......................................................................................................................................................... 7 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER............................................................................................... 7 4.7 TEST INSTRUMENTS LIST............................................................................................................................................. 8 5 TEST RESULTS AND MEASUREMENT DATA..................................................................................................... 9 5.1 ANTENNA REQUIREMENT: ........................................................................................................................................... 9 5.2 CONDUCTED EMISSIONS............................................................................................................................................ 10 5.3 CONDUCTED PEAK OUTPUT POWER.......................................................................................................................... 13 5.4 20DB OCCUPY BANDWIDTH...................................................................................................................................... 15 5.5 CARRIER FREQUENCIES SEPARATION........................................................................................................................ 17 5.6 HOPPING CHANNEL NUMBER.................................................................................................................................... 20 5.7 DWELL TIME............................................................................................................................................................. 21 5.8 PSEUDORANDOM FREQUENCY HOPPING SEQUENCE.................................................................................................. 23 5.9 BAND EDGE...........................................................................................…

Text truncated - open the document above for the full version.

Report No: GTSE13010000902 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 35 of 37 6 Test Setup Photo Radiated Spurious Emission Report No: GTSE13010000902 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 36 of 37 Conducted Emission Report No: GTSE13010000902 Global United Technology Service Co., Ltd. Project No.: GTSE130100009RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 37 of 37 7 EUT Constructional Details Reference to the test report No. GTSE13010000901 ------End of report------