AEZCPE-310-230W-CDMA subscriber terminal

OUTDOOR SOMAPORT USER GUIDE Part 006217 revision 01 3 Preface .................................................................................. 9 Regulatory Notices ........................................................................... 15 Introduction ....................................................................... 17 Overview ......................................................................................... 18 System Components ........................................................................ 19 The Indoor Unit .............................................................................. 20 Antenna ........................................................................................... 22 Connecting the Indoor Unit ............................................... 23 Connecting the Power Supply and Powering on the Indoor Unit .... 24 Connecting a Computer via Ethernet .............................................. 25 Connecting Telephones to the Indoor Unit ..................................... 26 Activating Service ............................................................................. 30 Connecting Multiple Computers ........................................ 31 Overview ......................................................................................... 32 Using an Ethernet Hub .................................................................... 33 Using an Internet Router ................................................................. 34 Troubleshooting ................................................................. 35 Finding Causes of Computer Problems ........................................... 36 Finding Causes of Telephone Problems .......................................... 38 Finding Causes of Outdoor Unit Problems ...................................... 40 The Signal is Weak .......................................................................... 41 There is a Fault Condition ............................................................... 43 CONTENTS 4 The SOMAport is Not Receiving Power .......................................... 44 There is a Problem with the Ethernet Cabling ................................. 45 The Computer Uses an Old Dial-up Connections ........................... 46 Internet Explorer LAN Settings are Incorrect ................................... 48 Ethernet Network Settings are Incorrect .......................................... 49 IP Address Needs to be Renewed ..................................................... 58 Specifications ......................................................................61 5 SOMA NETWORKS INC. ENDUSER PRODUCT LICENSE AGREEMENT THE OUTDOOR SOMAPORT™ SUBSCRIBER STATION AND PROVIDED SOFTWARE CON- TAIN CERTAIN COMPUTER PROGRAMS AND OTHER PROPRIETARY MATERIAL OF SOMA NETWORKS, INC. OR LICENSED TO SOMA NETWORKS, INC., THE USE OF WHICH IS SUB- JECT TO THIS AGREEMENT. BY: (A) SIGNING AN AGREEMENT FOR SERVICE WITH YOUR SERVICE PROVIDER; (B) OPENING THE SEALED ENVELOPE CONTAINING THE OUTDOOR SOMAPORT; OR (C) USING THE OUTDOOR SOMAPORT, YOU ASSENT TO AND ACCEPT THIS ENDUSER PRODUCT LICENSE AGREEMENT. IF YOU DO NOT AGREE WITH ALL THE TERMS OF THIS AGREEMENT YOU MUST RETURN THIS PRODUCT (WITH THE ENVE- LOPE STILL SEALED), ALL MANUALS AND DOCUMENTATION, ANY SOFTWARE PACKAGES PROVIDED WITH THE SOMAPORT AND PROOF OF PAYMENT TO THE PLACE YOU OBTAINED THEM FOR A FULL REFUND WITHIN THIRTY (30) DAYS OF FIRST ACQUIRING THE OUTDOOR SOMAPORT, OTHERWISE YOU ARE DEEMED TO HAVE ACCEPTED AND AGREED TO THESE TERMS AND CONDITIONS. UNAUTHORIZED REPRODUCTION, DIS- TRIBUTION, DECOMPILATION OR OTHER REVERSE ENGINEERING OF THIS PRODUCT INCLUDING ITS HARDWARE AND/OR SOFTWARE, OR ANY PORTION OF IT, IS PROHIB- ITED AND MAY RESULT IN SEVERE CIVIL AND CRIMINAL PENALTIES, AND WILL BE PROS- ECUTED TO THE MAXIMUM EXTENT POSSIBLE UNDER THE LAW. 1. GRANT OF LICENSE: Subject to the terms of this Enduser Product License Agreement (the "Agree- ment"), SOMA Networks, Inc. ("SOMA") grants you (the "Licensee") a non-sub-licensable, non-exclusive right ("License") to use the Product. "Product" means, collectively, the Software and the provided hardware, and specifically the Outdoor SOMAport™ subscriber station and its accessories, if any, together with docu- mentation provided to you by SOMA or your service provider. "Software" means, collectively, the version of the SOMA software program in object code format and all updates to that program distributed to you by SOMA, directly or indirectly, by any means and includes any firmware provided to you with the Product. You have no right, unless otherwise explicitly permitted, to receive any source code or design documentation relating to the Product. SOMA retains ownership of all Software copies. The Software and this License is only provided to you to be used in conjunction with the Outdoor SOMAport provided to you by SOMA or your service provider when you subscribed to services that utilize the SOMA wireless air interface technology and is not licensed to you to be used for any other purpose. 2. RESTRICTIONS: Except as reasonably required to use the Product strictly in accordance with the License and this Agreement, you may not copy any Software. Licensee shall not (and shall not allow any third party to): (I) decompile, disassemble, or otherwise reverse engineer or attempt to reconstruct or dis- cover any source code or underlying ideas or algorithms or file formats or programming or interoperability interfaces of the Product by any means whatsoever; (II) remove any Product identification, copyright or other notices; (III) modify, incorporate into or with other software or create a derivative work of any part of the Software or Product; or (IV) modify or otherwise alter the operation of the Product. Various compo- nents, functions, routines and/or portions of the Product may be protected by Intellectual Property Rights ("IPR") including, but not limited to, designs, copyrights, tra…

Text truncated - open the document above for the full version.

67 This chapter provides an overview of the Outdoor SOMAport. Contents Overview ............................................................................................................. 68 System Components ........................................................................................... 69 The Outdoor Unit Assembly ................................................................................ 70 Do You Have Everything? ................................................................................... 71 Antenna ............................................................................................................... 74 Safety Precautions .............................................................................................. 75 INTRODUCTION 68 Introduction OVERVIEW The Outdoor SOMAport™ subscriber terminal provides high-speed Internet access and telephone service. The SOMAport works like a cell phone, in that it communicates with your service provider’s network over the air and does not require a special wire connection. The SOMAport consists of two parts: an outdoor unit and an indoor unit. After installing the SOMAport, simply plug-in the indoor unit and connect it to your computer using the provided Ethernet cable. The SOMAport will automatically connect to your service provider and you can setup your account using a Web browser. If you are using your SOMAport to provide telephone service, you can connect ordinary telephones to it. Internet service The SOMAport provides a high-speed, "always on" internet connection, which means you can be connected to the Internet and still use your telephone. The SOMAport is designed to be left on – it should not be turned off when not in use. Telephone service The telephone service provided by the SOMAport is independent and separate from your phone service. Wireless services may differ from your traditional wired services. Consult with your wireless service provider for details. 69 Introduction SYSTEM COMPONENTS Outdoor Unit: The outdoor unit is a ruggedized box, typically pipe-mounted, that contains a radio modem and an internal antenna. It uses a single cable (CAT5) that transmits data, telephone, and power to and from the indoor unit. Indoor Unit: The indoor unit is placed inside subscriber’s residence and connects to the subscriber’s computer and telephones. The indoor unit also functions as an AC adapter for the outdoor unit. 70 Introduction THE OUTDOOR UNIT ASSEMBLY The following illustration shows the three main pieces that are shipped and that must be assembled as part of the installation. „Outdoor unit „Mounting bracket „Armrest pipe 71 Introduction DO YOU HAVE EVERYTHING? Before you begin, make sure you have everything you will need during the installation. The basic Outdoor SOMAport kit Verify that the kit contains the following parts: „Outdoor unit „Armrest pipe „Mounting bracket „Power supply „Indoor unit „Wood screws 3.1 x 32 (4) „Hexagon P-Less anchors 6 x 45 (4) „Flat washers, nominal diameter 6 (8) „Spring washers, nominal diameter 6 (8) „Hexagon nuts M6 (4) „U-bolts M6 (2) „Outdoor CAT5 cable with waterproof connector (40m) „RJ-45 connector for indoor unit „User Guide „Installation Guide 72 Introduction The installation kit The installation kit is an optional set of mounting hardware provided for subscribers who want to install the outdoor unit themselves. The kit contains the hardware you need to install the outdoor unit on a variety of surfaces (wall or roof). If you have this kit, verify that it contains the following parts „CAT5 cable assembly kit „Oxide-inhibiting compound „10 cable clips 73 Introduction Materials and tools In addition, you need the following materials and tools, which are not supplied with the basic Outdoor SOMAport or installation kits: „8, 10, 13 mm socket or open-end or box-end wrench or small adjustable wrench „Phillips-head screw driver No.2 „Pencil or chalk „Carpenter’s level „Silicone sealant „Double-expansion anchors „Electric drill with one of the following drill bits: „Diameter (Ø) 2.0, Ø4.5 Woodworking drill (if installing on wood or a roof) „Ø5.3 concrete drill (if installing on concrete or brick) „Ø10-20 mm woodworking or concrete drill (if you make hole for passing the cable) „Sticking-by-pressure tool (for RJ-45) 74 Introduction ANTENNA The outdoor unit communicates with a cellular tower operated by your wireless service provider. The outdoor unit contains an antenna that automatically steers itself toward the best signal when you plug in the SOMAport. It also periodically checks to see if the current antenna direction is optimal and adjusts automatically if required. ! WARNING: While this device is in operation, a separation distance of at least 20 centimeters (8 inches) must be maintained between the radiating antenna and any person exposed to the transmitter in order to meet the FCC RF exposure guidelines. No change to the antenna or device is permitted. Doing so may result in the installed system exceeding RF exposure requirements. This device must not be co-located or operating in conjunction with any other antenna or radio transmitter. Installers and end users must follow the installation instructions provided in this guide. 75 Introduction SAFETY PRECAUTIONS In addition to the safety instructions on page 11, follow these guidelines when installing the Outdoor SOMAport: „Carefully survey the job site before beginning the installation to locate secure handholds, dangerous conditions (such as power lines and weak roofs), and the safest and most convenient placements for ladders. „Do not climb on a wet or icy roof. „Do not attempt high installations on windy days. „Use only the sturdiest commercial-grade ladders – those with wide, slip preventive rungs and bases. „Do not position ladders at an angle steeper than 70°. Steeper angles can cause a ladder to slip sideways. „Dig the base of the ladder into the ground if possible. „Do not place ladders on slate that is…

Text truncated - open the document above for the full version.

Before beginning the installation, familiarize yourself with the top and side panels of the indoor unit. The lights on the top panel tell you when the SOMAport is ready. Off The SOMAport is not receiving power. Amber The SOMAport is booting and running its internal diagnostics. Flashing amber The SOMAport is upgrading its software. Green The SOMAport is powered and operating normally. Red An error occurred. The SOMAport is not currently functional. Off The SOMAport is not receiving power. Amber The SOMAport is attempting to locate a base station. Flashing amber The SOMAport cannot locate a base station. Flashing green The SOMAport has located a base station and is attempting to establish a connection. Green The SOMAport has located a base station and has established a connection. Red An error occurred. The SOMAport is not currently functional. Status Light Network Light When setting up the SOMAport, follow these guidelines:  Do not connect any third-party devices to the indoor unit, CAT5 cable, or outdoor unit.  Do not use the outdoor unit indoors. It must be mounted on a permanent outdoor structure. 1 Insert the connector of the power cord that is attached to the power supply into the power jack on the indoor unit. 2 Insert the socket end of the AC power cord into the power supply. 3 Position and orient the SOMAport in the location in which you plan on keeping it. 4 Insert the plug end of the AC power cord into a power outlet. The SOMAport takes up to five minutes to start, connect to your service provider’s network, and acquire a radio signal. The light on the power supply indicates whether or not it is receiving power. Wait until the Network light on the top of the SOMAport turns green before you begin connecting equipment to the SOMAport. The Outdoor SOMAport consists of two parts: an outdoor unit and an indoor unit. After installing the SOMAport, simply plug-in the indoor unit and connect it to your computer using the provided Ethernet cable. The SOMAport will automatically connect your service provider and you can setup your account using a Web browser. If you are using your SOMAport to provide telephone service, you can connect ordinary telephones to it. The Ethernet cable is supplied with the SOMAport. If your computer has an Ethernet port, use the Ethernet cable. If your computer does not have an Ethernet port, you will need to purchase an Ethernet card or an Ethernet-to-USB adapter. Copyright 2005 SOMA Netowrks, Inc. All Rights Reserved. SOMA, SOMA Networks and the star-and-circle design are trademarks or registered trademarks of SOMA Networks, All of SOMA Netwoks’ product names are trademarks of SOMA Netowrks, Inc. All other company and product names may be trademarks or registered trademarks of their respective owners. Products and services of SOMA Networks, Inc. may be protected by one or more pending or issued U.S. or foreign patents. Part 006218 revision 01 Before pluggin in the SOMAport, make sure that the CAT5 cable from the outdoor unit has been inserted to the ODU/IF port on the side of the indoor unit. If your service provider does not offer telephone service, or if you are not connecting a telephone to the SOMAport, go to step 5 to connect your computer. 1 Insert the telephone cord into the left jack (TEL-1) on the side of the SOMAport.  If your telephone service includes one telephone line only, you must use this jack.  If your telephone service includes two telephone lines, the telephone you connect to this jack will be serviced by TEL-1. 2 To connect a second telephone, do one of the following:  If your telephone service includes two telephone lines, insert the cord of the second telephone into the right jack (TEL-2).  If your telephone service includes one telephone line only, you must use a duplex adapter. 3 Pick up the handset and listen for a dial tone.  If you hear a series of tones (not a dial tone), the SOMAport is still booting. Hang up and try again when the status light turns green.  If you hear silence, make sure the cord is securely connected to the telephone and the SOMAport. See the SOMAport Setup Guide for troubleshooting information. Follow this step if you are using Ethernet. If you want to connect several computers to the SOMAport via a hub or router see the SOMAport User Guide. 1 Insert one end of the Ethernet cable into the Ethernet port on the SOMAport. 2 Insert the other end into the Ethernet port on the computer. 1 Restart your computer. 2 Launch a Web browser on the computer connected to the SOMAPort. 3 Direct your browser to a known valid Internet address (such as www. google.com).  If the page opens, full service has already been activated and you can begin using your SOMAport for Internet service.  If you are redirected to your service provider’s Web page, you must complete the sign-up procedure on the Web site to activate full service.  If you cannot open any Web pages at all: ψ Go to Step 7 “Run the connection wizard” if you used Ethernet to connect the computer to the SOMAport. For information about chaging network settings on Mac OS, see the SOMAport User Guide. If your version of Windows 95 does not have the Get on the Internet option or if you previously had a dial-up connection, you cannot use the wizard. See the SOMAport User Guide for information about manually changing network settings. 1 Start the Windows Internet Connection Wizard. 2 Do the following to complete the Wizard. 3 Restart your computer. 4 Launch a Web browser on the computer connected to the SOMAport and direct the browser to a known valid Internet address (such as www. google.com) Version Choose Windows 95 Start ψ Programs ψ Accessories ψ Internet Tools ψ Get on the Internet Windows Start ψ Programs ψ Accessories ψ 98/2000ME Communications ψ Internet Connection Wizard Windows XP Start ψ Programs ψ Accessories ψ Communications ψ New Connection Wizard Version Choose Windows 1 Choose I want to set up my Internet 95/98/ME/ connection manually, or I want …

Text truncated - open the document above for the full version.

TNO Electronic Products & Services (EPS) B.V. Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno.nl T +31 594 505005 F +31 594 504804 E [email protected] Subject Cover letter Date May 22, 2006 Our reference 05K0783a Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands Telefication B.V. Attn.: W. Blom Edisonstraat 12a 6902 PK Zevenaar The Netherlands Dear Mr. Blom, On behalf of our customer Sanyo Electric Co., Ltd., we hereby would like to apply for FCC certification of the following device: FCC ID : AEZCPE-310-230 Model number : CPE-310-230 Description : W-CDMA Subscriber Terminal Equipment class : Licensed non-broadcast station transmitter The following PDF files (exhibits) are electronically submitted: 1. Cover letter containing the request for FCC certification (1 file) 2. Request for confidentiality (1 file) 3. Form 731 (1 file) 4. Test report in conformity with 47 CFR Part 27 (1 file) 5. Bill of materials (1 file) 6. Circuit diagram (4 files) 7. Block diagram (2 files) 8. Operational description (1 file) 9. Interior photographs (2 files) 10. Exterior photographs (2 files) 11. Test setup photographs (1 file) 12. MPE statement (1 file) 13. Authorization letter (1 file) 14. User manual (3 files) 15. Label information/location (1 file) Best regards, TNO Electronic Products & Services (EPS) B.V. P.A.J.M. Robben, B.Sc.E.E. Director

TNO Electronic Products & Services (EPS) B.V. Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno.nl T +31 594 505005 F +31 594 504804 E [email protected] Subject Request for confidentiality Date May 22, 2006 Our reference 05K0783b Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands Telefication B.V. Attn.: W. Blom Edisonstraat 12a 6902 PK Zevenaar The Netherlands Dear Mr. Blom, Pursuant to section 0.457 of the FCC rules we herewith request the following exhibits, related to this application for FCC ID: AEZCPE-310-230, to be withheld from public inspection and to be kept confidential. The contents of these exhibits may not be disclosed to other parties than Sanyo Electric Co., Ltd. and TNO Electronic Products & Services (EPS) B.V.: 1. Bill of materials 2. Circuit diagram 3. Operational description 4. Block diagram The reason for this request for confidentiality is that the information contained in the exhibits as listed above has been classified as company confidential. Disclosure of any portion of this information to other parties would cause substantial competitive harm. Best regards, TNO Electronic Products & Services (EPS) B.V. P.A.J.M. Robben, B.Sc.E.E. Director

1. Body: Front View 2. Body: Back View 3. Body: Top View 4. Body: Bottom View 5. Body: Left-side View 6. Body: Right-side View 7. Body: Close-up of Label(Front)

1. Body: Front View 2. Body: Back View 3. Body: Top View 4. Body: Bottom View 5. Body: Left-side View 6. Body: Right-side View 7. Body: Close-up of Label(Front)

FCC ID: AEZCPE-310-230 Label location: the label is located at the side of the device.

1. Inside view Left: Cabinet front Right: IDU board 2. Cabinet back 3. IDU board(front view) 4. IDU board (back view)

1. Inside view Left: Cover RF Right: Shield RF (center) 2. Inside view Left: Shield RF Right: RF board (center) 3. Inside view Top: Cabinet front Under: BB board 4. Cabinet back 5. RF board(front view) 6. RF board (back view) 7. BB board(front view) 8. BB board(back view)

Declaration on radiation safety standard conformance To whom it may concern: Sanyo Electric Co., Ltd. 1-1 Sanyo-cho Daito City Osaka 574-8534 Japan declares that the following product FCC ID : AEZCPE-310-230 Model number : CPE-310-230 Description : W-CDMA Subscriber Terminal Equipment class : Licensed non-broadcast station transmitter has a maximum e.i.r.p. of 30.5 dBm (1122 mW) in the frequency ranges of 2305 - 2315 MHz . The prediction of the power density at 20 cm distance of the radiating structures of the product can be calculated as follows (in accordance with OET Bulletin 65 (edition 97-01), page 19, equation 4): EIRP S = 4*π * R 2 EIRP 1122 mW S = 4*π*R 2 = 4 *π*(20cm) 2 = 0.22 mW/cm 2 (limit = 1.0 mW/cm 2 ) This means that the product as defined above fulfills the requirements on power density for general population/uncontrolled exposure with reference to table 1 (B) of 47 CFR Part 1.1310 where the limit for power density in the frequency range of 1.5 - 100.0 GHz has been set to 1.0 mW/cm 2 .

Sanyo Electric Co., Ltd. Testing Laboratory 7-3-2 Higashimachi, Ibukidai, Nishi-ku Kobe-city, Hyogo Prefecture 651-2242 Japan Telephone: +81 78 993 1062 Telefax: +81 78 993 1097 Project number: - Page 1 of 36 TEST REPORT OF A W-CDMA SUBSCRIBER TERMINAL, MODEL CPE-310-230, BRAND SOMA NETWORKS, IN ACCORDANCE WITH 47 CFR PART 27 (2005-10-01). Description of EUT: Manufacturer: Brand mark: Model: FCC ID: W-CDMA subscriber terminal Sanyo Electric Co., Ltd. SOMA Networks CPE ñ310-230 AEZCPE-310-230 Project number: - Page 2 of 36 MEASUREMENT/TECHNICAL REPORT Sanyo Electric Co., Ltd. Model : CPE-310-230 FCC ID: AEZCPE-310-230 May 12, 2006 This report concerns: Original grant/certification Class 2 change Verification Equipment type: Licensed non-broadcast station transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii) ? Yes No Report prepared by: Company name : Sanyo Electric Co., Ltd. Testing Laboratory Address : 7-3-2 Higashimachi, Ibukidai, Nishi-ku Postal code/city : Kobe-city, Hyogo Prefecture, 651-2242 Mailing address : - Postal code/city : - Country : Japan Telephone number : +81 78 993 1062 Telefax number : +81 78 993 1097 The data taken for this test and report herein was done in accordance with 47 CFR Part 27 (Miscellaneous Wireless Communications Services) and the measurement procedures of ANSI C63.4: 2003. Sanyo Electric Co., Ltd. Testing Laboratory at Kobe-city, Japan, certifies that the data is accurate and contains a true representation of the emission profile of the Equipment Under Test (EUT) on the date of the test as noted in the test report. I have reviewed the test report and find it to be an accurate description of the test(s) performed and the EUT so tested. Date: May 12, 2006 Signature: H. Wada Sanyo Electric Co., Ltd. Testing Laboratory Description of EUT: Manufacturer: Brand mark: Model: FCC ID: W-CDMA subscriber terminal Sanyo Electric Co., Ltd. SOMA Networks CPE ñ310-230 AEZCPE-310-230 Project number: - Page 3 of 36 Description of test item Test item : W-CDMA subscriber terminal Manufacturer : Sanyo Electric Co., Ltd. Brand : SOMA Networks Model : CPE-310-230 Serial numbers : - Revision : - Receipt number : 1 Receipt date : May 8, 2006 Applicant information Applicant's representative : Mr. O. Shimizu Company : Sanyo Electric Co., Ltd. Address : 1-1 Sanyo-cho Daito City Postal code : 574-8534 City : Osaka PO-box : - Postal code : - City : - Country : Japan Telephone number : +81 72 870 6532 Telefax number : +81 72 870 6597 Test(s) performed Location : Kobe-city Test(s) started : May 8, 2006 Test(s) completed : May 10, 2006 Purpose of test(s) : Type approval / certification Test specification(s) : 47 CFR Part 27 (2005-10-01) Test engineer(s) : H. Izuka K. Yamamoto I. Nakajo : Description of EUT: Manufacturer: Brand mark: Model: FCC ID: W-CDMA subscriber terminal Sanyo Electric Co., Ltd. SOMA Networks CPE ñ310-230 AEZCPE-310-230 Project number: - Page 4 of 36 Table of contents 1 General information ...............................................................................................................................................................5 1.1 Product description.........................................................................................................................................................5 1.2 Related submittal(s) and/or Grant(s) ..............................................................................................................................5 1.3 Tested system details......................................................................................................................................................5 1.4 Test methodology ...........................................................................................................................................................6 1.5 Test facility.....................................................................................................................................................................6 1.6 Product labeling..............................................................................................................................................................6 1.7 System test configuration ...............................................................................................................................................7 1.7.1 Justification ............................................................................................................................................................7 1.7.2 EUT exercise software ...........................................................................................................................................7 1.8 Special accessories .........................................................................................................................................................7 1.9 Equipment modifications................................................................................................................................................7 1.10 Configuration of the tested system .................................................................................................................................7 1.11 Block diagram(s) of the EUT .........................................................................................................................................7 2 Transmitter tests .....................................................................................................................................................................8 2.1 RF output power (conducted) .........................................................................................................................................8 2.1.1 Test results..............................................................................................................................................................8 2.2 RF output power (EIRP)....................…

Text truncated - open the document above for the full version.

Sanyo Electric Co., Ltd. Testing Laboratory 7-3-2 Higashimachi, Ibukidai, Nishi-ku Kobe-city, Hyogo Prefecture 651-2242 Japan Telephone: +81 78 993 1062 Telefax: +81 78 993 1097 Project number: - Page 1 of 12 47 CFR PART 27 TEST SETUP PHOTOGRAPHS OF A W-CDMA SUBSCRIBER TERMINAL (LICENSED NON- BROADCAST STATION TRANSMITTER), BRAND SOMA NETWORKS, MODEL CPE-310-230. Description of EUT: Manufacturer: Brand mark: Model: FCC ID: W-CDMA subscriber terminal Sanyo Electric Co., Ltd. SOMA Networks CPE-310-230 AEZCPE-310-230 Project number: - Page 2 of 12 Description of test item Test item : W-CDMA subscriber terminal Manufacturer : Sanyo Electric Co., Ltd. Brand : SOMA Networks Model : CPE-310-230 Serial nu…

Text truncated - open the document above for the full version.