AFJ297900VHF Mobile Transceiver

INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER iF5063 iF5061 i EXPLICIT DEFINITIONS R WARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electricshock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruinthe transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting,the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodilyinjury. NEVER allow children to touch the transceiver. NEVER expose the transceiver to rain, snow or any liquids. USE the specified microphone only. Other microphones have different pin assignments and may damage the trans-ceiver. DO NOT use or place the transceiver in areas with tem- peratures below –30°C (–22°F) or above +60°C (+140°F), orin areas subject to direct sunlight, such as the dashboard. PRECAUTIONS WORD DEFINITION R WARNING Personal injury, fire hazard or electric shockmay occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No riskof personal injury, fire or electric shock. READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructionsfor the IC-F5061 and IC-F5063 VHF MOBILE TRANS- CEIVERS . IMPORTANTIcom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany,France, Spain, Russia and/or other countries.All other products or brands are registered trademarks or trademarks of theirrespective holders. NOTE: See the operating guide for details of BIIS, MDC and LTR operation. Ask your dealer for details. ii AVOID operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if thetransceiver transmits while the vehicle’s engine OFF.AVOID placing the transceiver in excessively dusty envi- ronments. AVOID placing the transceiver against walls. This will obstruct heat dissipation. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver sur-faces.BE CAREFUL! The transceiver will become hot when operating continuously for long periods.For U.S.A. onlyCAUTION: Changes or modifications to this transceiver, not ex- pressly approved by Icom Inc., could void your authority to operatethis transceiver under FCC regulations. TABLE OF CONTENTSIMPORTANT .................................................................................... iEXPLICIT DEFINITIONS ................................................................. iPRECAUTIONS ............................................................................... iTABLE OF CONTENTS .................................................................. ii1 PANEL DESCRIPTION ........................................................... 1–7  Front panel ............................................................................... 1  Function display ....................................................................... 2  Programmable function keys ................................................... 3 2 BASIC OPERATION ............................................................. 8–13  Turning power ON .................................................................... 8  Channel selection .................................................................... 8  Call procedure .......................................................................... 9  Receiving and transmitting ....................................................... 9 D Transmitting notes ............................................................... 10 D TX code channel selection .................................................. 10 D TX code number edit............................................................ 11 D Talkgroup ID code selection ................................................ 12 D TX Status message selection .............................................. 12 D DTMF transmission ............................................................. 12  Scrambler function ................................................................. 13  User set mode ........................................................................ 13 3 CONNECTION AND MAINTENANCE ................................ 15–17  Rear panel connection ........................................................... 15  Supplied Accessories ............................................................. 16  Mounting the transceiver......................................................... 16  Antenna................................................................................... 17  Fuse replacement .................................................................. 17  Cleaning ................................................................................. 17  Options ................................................................................... 17 4 SAFETY TRAINING INFORMATION ........................................ 18 1 1 PANEL DESCRIPTION IcomInc. qe y Speaker Function display (p. 2) w r t  Front panel q AF VOLUME CONTROL KNOBRotate the knob to adjust the audio output level.• Minimum audio level is pre-programmed. w TRANSMIT INDICATOR ➥ Lights red while transmitting a signal. ➥ Lights green while receiving a signal. e UP/DOWN KEYSPush to select an operating channel, etc.*The desired function can be assigned by your dealer. (p. 3) r POWER SWITCH [POWER]Push to turn the power ON and OFF.• Automatic scan start, Password prompt and Set mode access are available at power ON. t DEALER-PROGRAMMABLE KEYS Desired functions can be programmed independently byyour dealer. (p. 3) y MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro-phone. NEVER connect non-specified microphones. The p…

Text truncated - open the document above for the full version.

January 17, 2007 AmericanTCB, Inc. 6731 Whittier Avenue, Suite C110 McLean, VA 22101 Subject: Equipment Authorization under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 400-470 MHz (25 KHz, 12.5 KHz and 6.25 KHz Channel Spacings). Applicant: ICOM Incorporated Product: VHF Mobile Transceiver Model: IC-F5061 FCC ID: AFJ297900 Dear Sir/Madam, As appointed agent for ICOM Incorporated, we would like to submit the application to Federal Communications Commission for certification of the above product. Please review all files uploaded to ATCB electronic filing site. If you have any queries, please do not hesitate to contact us by our TOLL FREE number: OUR TELEPHONE NO.: 1-877-747-6381 Yours truly, Tri Minh Luu, P. Eng., V.P., Engineering UltraTech Group of Labs Ultratech’s Accreditations: 0685 31040/SIT C-1376 46390-2049 200093-0 SL2-IN-E-1119R 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected]

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 January 22, 2007 RE: FCC ID: AFJ297900_ATCB004457 Attention: Tri Luu I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please check the emissions designators on the 731 to make sure they are in alignment with the new FCC interpretation on frequency listings on the grant as follows: Licensed transmitters Generally, list only allowed frequencies in rule part applied for. However, contiguous frequency ranges that extend allowed frequencies and include adjacent frequencies outside the applied rule part are allowed under the following conditions. All of the following must be adhered to. a. Extended frequency ranges in the line item must have portion of the band fall within the operating range of the rule part(s) listed. b. Frequency range and rule part combos solely outside USA frequencies are not allowed. The device must be capable of operating on frequencies in the frequency band listed. c. Any frequency in extended frequency range must not conflict with any rule part with different specifications. In this case, the following must be evaluated. 1) Rule parts applied for and allocation chart in 2.106 are used to check for allowed frequencies or show conflicting frequency range. 2) Portion of band must not be used solely for a rule part not applied for unless justification in (e), below, applies. Consider splitting rule parts in different line items to remove ambiguity if needed. d. For multiple rule part line item, tighter specs must apply where frequency ranges are common between rule parts. e. The filing must have a justification letter for extended frequencies outside of applied rule part. Operation must be justified under 2.807. For example, Government / Military use or exportation to other countries has been allowed. • Justification letter from grantee must indicate marketing plans to ensure USA users, other than those specifically identified, cannot operate device outside bands allowed under the relevant rule parts applied for. f. Frequencies must adhere to the following additional requirements below. 1) Part 87 listings must have only Part 87 frequencies. Extended frequencies not allowed for Part 87 devices. 2) Device must not be capable of operating under 406-406.1 MHz unless rule part applied for specifically allows it. g. Test guidance i. Test only on allowed frequencies. ii. Test at least one frequency, unless required to test on multiple frequencies, in each band for each rule part applied for and ensure the device is capable of operating on the frequency in each rule part. Test on one frequency may be accepted if multiple listed bands for a rule part with a continuous frequency range listing, if the listed bands are split to remove a conflict with other rules and the technical requirements in the split bands are the same. Other requirements for RF exposure may apply. h. All Certification grants with extended frequencies must have the following grant note: This device contains functions that are not operational in U.S Territories except as noted in the filing. This filing is only applicable for US operations. These policies include certain frequency ranges (i.e. 136-150MHZ). Please review the above policy and correct the 731 form and other documentation as necessary to be in line with this new interpretation. 2. Please note that additional comments may result depending on the response to the above. z Page 2 January 22, 2007 Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

1 2 3

IC-F5061 FCC ID LABEL CAUTION LABEL

4 5 6 7 8

S= power density P= power input to the antenna G= power gain of the antenna in the direction of 1 interest relative to an isotropic radiator R= distance to the center of radiation of the antenna Choose Occupational/Controlled General Population/Uncontrolled Tx Frequency: 136.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 47.000 (dBm) Antenna gain : 0.00 (dBi) S=1.0000 (mW/cm^2) P=50118.7234 (mW) G=1.0000 (numeric) R =63.1532(cm) S (mw/cm^2) at specific distance in cm Enter distance desired in cm 9.96000066820 OET Bulletin 65, Edition 97-01 Prediction of MPE Limit Equation from page 18 2 4R PG S π = 4 R PG S π =

VHF Mobile Transceiver Model No.: IC-F5061 FCC ID: AFJ297900 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: ICOM-142F90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: January 17, 2007 Report Prepared by: JaeWook Choi Issued Date: January 17, 2007 Tested by: Wayne Wu, Hung Trinh Test Dates: December 18 – December 20, 2006, December 27, 2006 – January 3, 2007 ƒ The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. ƒ This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] 0685 31040/SIT C-1376 46390-2049 200093-0 SL2-IN-E-1119R FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Contents i VHF Mobile Transceiver, Model IC-F5061 FCC ID: AFJ297900 ULTRATECH GROUP OF LABS File #: ICOM-142F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 17, 2007 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST........................................................................................................................ 1 EXHIBIT 2. INTRODUCTION ......................................................................................................................................... 2 2.1. SCOPE......................................................................................................................................................................... 2 2.2. RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................... 2 2.3. NORMATIVE REFERENCES ................................................................................................................................... 2 EXHIBIT 3. PERFORMANCE ASSESSMENT .............................................................................................................. 3 3.1. CLIENT INFORMATION .......................................................................................................................................... 3 3.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ............................................................................................. 3 3.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................4 3.4. LIST OF EUT’S PORTS ............................................................................................................................................. 5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ............................... 6 4.1. CLIMATE TEST CONDITIONS ................................................................................................................................ 6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS .............................................. 6 EXHIBIT 5. SUMMARY OF TEST RESULTS ............................................................................................................... 7 5.1. LOCATION OF TESTS .............................................................................................................................................. 7 5.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ........................................................................ 7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ........................................ 7 5.4. DEVIATION OF STANDARD TEST PROCEDURES.............................................................................................. 7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS............................... 8 6.1. TEST PROCEDURES................................................................................................................................................. 8 6.2. MEASUREMENT UNCERTAINTIES ...................................................................................................................... 8 6.3. MEASUREMENT EQUIPMENT USED.................................................................................................................... 8 6.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ......................................... 8 6.5. RF POWER OUTPUT [§§ 2.1046 & 90.205] .............................................................................................................. 9 6.6. FREQUENCY STABILITY [§§ 2.1055 & 90.213]................................................................................................... 10 6.7. AUDIO FREQUENCY RESPONSE [§ 2.1047(A)]................................................................................................... 12 6.8. MODULATION LIMITING [§§ 2.1047(B) & 90.210] ............................................................................................. 17 6.9. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 90.209 & 90.210] .................................................. 22 6.10. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§ 90.210] ..... 84 6.11. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 90.210] .......................................... 101 6.12. TRANSIENT FREQUENCY BEHAVIOR [§ 90.214]..................................................................................…

Text truncated - open the document above for the full version.