AFJ298001UHF Mobile Transceiver

INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER iF5063 iF5061 UHF MOBILE TRANSCEIVER iF6063 iF6061 i EXPLICIT DEFINITIONS R WARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electricshock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruinthe transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting,the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodilyinjury. NEVER allow children to touch the transceiver. NEVER expose the transceiver to rain, snow or any liquids. USE the specified microphone only. Other microphones have different pin assignments and may damage the trans-ceiver. DO NOT use or place the transceiver in areas with tem- peratures below –30°C (–22°F) or above +60°C (+140°F), orin areas subject to direct sunlight, such as the dashboard. PRECAUTIONS WORD DEFINITION R WARNING Personal injury, fire hazard or electric shockmay occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No riskof personal injury, fire or electric shock. READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructionsfor the IC-F5061, IC-F5063, IC-F6061 and IC-F6063 VHF/UHF MOBILE TRANSCEIVERS . IMPORTANTIcom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany,France, Spain, Russia and/or other countries.LTR is a registered trademark of the E.F.Johnson Company.All other products or brands are registered trademarks or trademarks of theirrespective holders. See the operating guide for details of BIIS, MDC and LTR ® system operations. Ask your dealer for details. ii AVOID operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if thetransceiver transmits while the vehicle’s engine OFF.AVOID placing the transceiver in excessively dusty envi- ronments. AVOID placing the transceiver against walls. Otherwise heat dissipation will be obstructed.AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver sur-faces.BE CAREFUL! The transceiver will become hot when operating continuously for long periods.For U.S.A. onlyCAUTION: Changes or modifications to this transceiver, not ex- pressly approved by Icom Inc., could void your authority to operatethis transceiver under FCC regulations. TABLE OF CONTENTSIMPORTANT .................................................................................... iEXPLICIT DEFINITIONS ................................................................. iPRECAUTIONS ............................................................................... iTABLE OF CONTENTS .................................................................. ii1 PANEL DESCRIPTION ........................................................... 1–7  Front panel ............................................................................... 1  Function display ....................................................................... 2  Programmable function keys ................................................... 3 2 BASIC OPERATION ............................................................. 8–14  Turning power ON .................................................................... 8  Channel selection .................................................................... 8  Call procedure .......................................................................... 9  Receiving and transmitting ....................................................... 9 D Transmitting notes ............................................................... 10 D TX code channel selection .................................................. 10 D TX code number edit............................................................ 11 D Talkgroup ID code selection ................................................ 12 D TX Status message selection .............................................. 12 D DTMF transmission ............................................................. 13  Scrambler function ................................................................. 13  User set mode ........................................................................ 14 3 CONNECTION AND MAINTENANCE ................................ 15–17  Rear panel connection ........................................................... 15  Supplied Accessories ............................................................. 16  Mounting the transceiver......................................................... 16  Antenna................................................................................... 17  Fuse replacement .................................................................. 17  Cleaning ................................................................................. 17  Options ................................................................................... 17 4 SAFETY TRAINING INFORMATION ........................................ 18 1 1 PANEL DESCRIPTION IcomInc. qe y Speaker Function display (p. 2) w r t  Front panel q AF VOLUME CONTROL KNOB [VOL]Rotate the knob to adjust the audio output level.• Minimum audio level is pre-programmed. w LED INDICATOR ➥ Lights red while transmitting a signal. ➥ Lights green while receiving a signal. e UP/DOWN KEYS [CH Up]/[CH Down]Push to select an operating channel, etc.*The desired function can be assigned by your dealer. (p. 3) r POWER SWITCH [ ] Push to turn the power ON and OFF.• Automatic scan start, Password prompt and Set mode access are available at power ON. t DEALER-PROGRAMMABLE KEYS Desired functions can be programmed independently byyour d…

Text truncated - open the document above for the full version.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 February 21, 2007 RE: FCC ID: AFJ298001_ATCB004563 Attention: Tri Luu I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that the report states that the 2005 version of 47CFR Part 90 was used. Please note that part 90 has changed in many aspects since 2005. Please use the latest and most current version of the CFRs when testing to Part 90. Please confirm that all testing results are compliant to the latest FCC rules. The latest FCC rules may be found at http://ecfr.gpoaccess.gov/cgi/t/text/text- idx?c=ecfr&sid=d119a323af32d14f104e90e1030a5c8e&rgn=div5&view=text&node=47:5.0.1.1.3&i dno=47. 2. FYI – Please note that 406.1- 416MHz under part 90 is an operational fixed category. This device appears to be a mobile only type device. It is not clear from the new FCC interpretations if the 406.1MHz test frequency is suitable for this device. Please be aware of this possible difficulty. 3. Please note that the frequency band between 406- 406.1 is emergency position indicator radio beacon frequencies. Please note that a part 90 device may not transmit any portion of its signal may be in that band. Please note that your test data taken at a center frequency of 406.1 shows the lower sideband as non compliant as it operates in the forbidden 406-406.1MHz band. Please retest this lower frequency so that no part of the transmitted signal higher than the 99% bandwidth falls within the forbidden band. 4. Please note that as this application includes extended frequencies for Part 90 testing must still be only on part 90 frequencies. Please note that 435.05 MHz does not appear to be a part 90 frequency and thus should not have been tested. Please either remove the data for this frequency or please test on another frequency that is part 90 (i.e perhaps 453.0125MHz). 5. Please provide an MPE report supporting the 48cm separation requirement in the manual. 6. Please provide a letter justifying why the frequency range listed on the grant should include non part 90 extended frequencies. Such justification may be military use or exportation etc. This is a requirement of the latest FCC interpretations dealing with listing extended frequencies. 7. Please note that additional comments may results depending on the resolution of the above items. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

FRONT LEFT BACK RIGHT SERIAL

IC-F6061 FCC ID LABEL CAUTION LABEL

CHASSIS with Board CHASSIS inside MAIN side A MAIN side B FRONT side A FRONT side B CONNECT side A CONNECT side B UT-119 side A UT-119 side B

FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Page 163 UHF Mobile Transceiver, Model IC-F6061 FCC ID: AFJ298001 ULTRATECH GROUP OF LABS File #: ICOM-143F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 February 13, 2007 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) 6.13. RF EXPOSURE REQUIRMENTS [ 1.1310 & 2.1091] The following criteria shall be used to evaluate the environmental impact of human exposure to RF radiation: FCC 1.1310:- The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). TABLE 1—LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 ......................... 614 1.63 *(100) 6 3.0–30 .......................... 1842/f 4.89/f *(900/f 2 ) 6 30–300 ......................... 61.4 0.163 1.0 6 300–1500 ..................... .............................. .............................. f/300 6 1500–100,000 ............... .............................. .............................. 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 ...................... 614 1.63 *(100) 30 1.34–30 ....................... 824/f 2.19/f *(180/f 2 ) 30 30–300 ......................... 27.5 0.073 0.2 30 300–1500 ..................... .............................. .............................. f/1500 30 1500–100,000 ............. .............................. .............................. 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be ex- posed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. Calculation Method of RF Safety Distance : S = PG/4Πr 2 = EIRP/4πr 2 ==> r = SPGπ4/ = SEIRPπ4/ Where: P: power input to the antenna in mW EIRP: Equivalent (effective) isotropic radiated power. S: power density mW/cm 2 G: numeric gain of antenna relative to isotropic radiator r: distance to center of radiation in cm FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Page 164 UHF Mobile Transceiver, Model IC-F6061 FCC ID: AFJ298001 ULTRATECH GROUP OF LABS File #: ICOM-143F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 February 13, 2007 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) MPE Evaluation Evaluation of RF Exposure Compliance Requirements RF Exposure Requirements Compliance with FCC Rules Minimum calculated separation distance between antenna and persons required: 48 cm Manufacturer’ instruction for separation distance between antenna and persons required: 48 cm Antenna installation and device operating instructions for installers (professional/unskilled users), and the parties responsible for ensuring compliance with the RF exposure requirement See user manual. Caution statements and/or warning labels that are necessary in order to comply with the exposure limits See user manual. Any other RF exposure related issues that may affect MPE compliance None. Limits for General Population/Uncontrolled Exposure: Antenna Gain = 0 dBi = 10 (0/10) numeric Pp = 46.53 dBm (Rated peak power) Duty Cycle = 100 % Pa = Pp + 10*log(Duty Cycle) = 46.53 dBm + 10*log(100/100) dBm = 46.53 dBm = 45000 mW (rated average power) S = f/300 = 1.5 mW/cm 2 (Limit for General Population/Uncontrolled Exposure) r = SGP a π4/ = () SmWπ4/145000×= 48 cm

UHF Mobile Transceiver Model No.: IC-F6061 FCC ID: AFJ298001 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: ICOM-143F90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: February 13, 2007 Report Prepared by: JaeWook Choi Issued Date: February 13, 2007 Revised Date: March 13, 2007 Tested by: Wayne Wu, Hung Trinh Test Dates: January 18 ~ January 25, 2007, February 5 ~ February 6, 2007 ƒ The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. ƒ This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] 0685 31040/SIT C-1376 46390-2049 200093-0 SL2-IN-E-1119R FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Contents i UHF Mobile Transceiver, Model IC-F6061 FCC ID: AFJ298001 ULTRATECH GROUP OF LABS File #: ICOM-143F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 February 13, 2007 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST........................................................................................................................ 1 EXHIBIT 2. INTRODUCTION ......................................................................................................................................... 2 2.1. SCOPE......................................................................................................................................................................... 2 2.2. RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................... 2 2.3. NORMATIVE REFERENCES ................................................................................................................................... 2 EXHIBIT 3. PERFORMANCE ASSESSMENT .............................................................................................................. 3 3.1. CLIENT INFORMATION .......................................................................................................................................... 3 3.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ............................................................................................. 3 3.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................4 3.4. LIST OF EUT’S PORTS ............................................................................................................................................. 5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ............................... 6 4.1. CLIMATE TEST CONDITIONS ................................................................................................................................ 6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS .............................................. 6 EXHIBIT 5. SUMMARY OF TEST RESULTS ............................................................................................................... 7 5.1. LOCATION OF TESTS .............................................................................................................................................. 7 5.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ........................................................................ 7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ........................................ 7 5.4. DEVIATION OF STANDARD TEST PROCEDURES.............................................................................................. 7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS............................... 8 6.1. TEST PROCEDURES................................................................................................................................................. 8 6.2. MEASUREMENT UNCERTAINTIES ...................................................................................................................... 8 6.3. MEASUREMENT EQUIPMENT USED.................................................................................................................... 8 6.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ......................................... 8 6.5. RF POWER OUTPUT [§§ 2.1046 & 90.205] .............................................................................................................. 9 6.6. FREQUENCY STABILITY [§§ 2.1055 & 90.213]................................................................................................... 11 6.7. AUDIO FREQUENCY RESPONSE [§ 2.1047(A)]................................................................................................... 14 6.8. MODULATION LIMITING [§§ 2.1047(B) & 90.210] ............................................................................................. 19 6.9. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 90.209 & 90.210] .................................................. 24 6.10. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§ 90.210] ... 127 6.11. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 90.210] .......................................... 149 6.12. TRANSIENT FREQUENCY BEHAVIOR [§ 90.214]...........................................................…

Text truncated - open the document above for the full version.