AFJ318300HF/VHF/UHF Transceiver

HF/VHF/UHF TRANSCEIVER i9100 INSTRUCTION MANUAL i FOREWORD Thank you for making the IC-9100 your radio of choice. We hope you agree with Icom’s philosophy of “technology first.” Many hours of research and devel- opment went into the design of your IC-9100. FEATURES MThe IC-9100 fully covers HF to 1200 MHz* 1 multi- band in one transceiver MIndependent dual receivers in one radio; receives two different bands simultaneously MOptional D-STAR (Digital Smart Technology for Am- ateur Radio) allows you to operate in the DV mode* 2 for digital voice and low speed data communication. Linking of D-STAR repeaters over the Internet al- lows you to communicate virtually anywhere. MSatellite mode operation *1 The optional UX-9100 is required for 1200 MHz fre- quency band operation. *2 The optional UT-121 is required for the DV mode opera- tion. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the IC-9100. EXPLICIT DEFINITIONS WORDDEFINITION RDANGER! Personal death, serious injury or an ex- plosion may occur. RWARNING! Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Spurious signals may be received near some fre- quencies. These are created in the internal circuit and does not indicate a transceiver malfunction. SUPPLIED ACCESSORIES The transceiver comes with the following accessories. Qty. q Hand microphone ............................................ 1 w DC power cable* ............................................. 1 e Spare fuse (ATC 5 A) ...................................... 1 r Spare fuse (ATC 30 A) .................................... 2 tACC cable ......................................................... 1 y6.3 (d) mm plug................................................. 1 uDouble-sided tape............................................. 1 q e y t w r u w For European versions (see p. 27 for installation details) *Differs depending on the version. FCC INFORMATION s&/2#,!33"5.).4%.4)/.!,2!$)!4/23 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures: s2EORIENTORRELOCATETHERECEIVINGANTENNA s)NCREASETHESEPARATIONBETWEENTHEEQUIPMENT and receiver. s#ONNECTTHEEQUIPMENTINTOANOUTLETONA circuit different from that to which the receiver is connected. s#ONSULTTHEDEALERORANEXPERIENCEDRADIO46 technician for help. PRECAUTIONS RDANGER HIGH RF VOLTAGE! NEVER attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continu- ous high volume operation. If you experience a ringing in your ears, reduce the volume or discontinue use. R WARNING! NEVERoperate or touch the transceiver with wet hands. This may result in an electric shock or damage to the transceiver. R WARNING! NEVER apply AC power to the [DC13.8V] socket on the transceiver rear panel. This could cause a fire or damage the transceiver. R WARNING! NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver may be damaged. R WARNING! NEVER apply more than 16 V DC to the [DC13.8V] socket on the transceiver rear panel, or use reverse polarity. This could cause a fire or damage the transceiver. R WARNING! NEVER let metal, wire or other objects protrude into the transceiver or into connectors on the rear panel. This may result in an electric shock. R WARNING! Immediately turn OFF the trans- ceiver power and remove the power cable if it emits an abnormal odor, sound or smoke. Contact your Icom dealer or distributor for advice. R WARNING! NEVER put the transceiver in any unstable place (such as on a slanted surface or vibrated place). This may cause injury and/or damage to the transceiver. CAUTION: NEVERchange the internal settings of the transceiver. This may reduce transceiver perfor- mance and/or damage to the transceiver. In particular, incorrect settings for transmitter circuits, such as output power, idling current, etc., might damage the expensive final devices. The transceiver warranty does not cover any prob- lems caused by unauthorized internal adjustment. CAUTION: NEVERblock any cooling vents on the top, rear, sides or bottom of the transceiver. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. CAUTION:NEVERinstall the transceiver in a place without adequate ventilation. Heat dissipation may be reduced, and the transceiver may be damaged. DO NOTuse harsh solvents such as benzine or alcohol when cleaning, as they will damage the trans- ceiver surfaces. DO NOTpush the PTT switch when you don’t actu- ally desire to transmit. DO NOT use or place the transceiver in areas with temperatures below ±0°C (+32°F) or above +50°C (+122°F). DO NOT place the transceiver in excessively dusty environments or in direct sunlight. DO NOT place the transceiver against walls or putting anything on top of the transceiver. This may overheat the…

Text truncated - open the document above for the full version.

8 93 DV MODE OPERATION N$IGITALMODEOPERATION The IC-9100 can be operated in the digital voice mode, including low-speed data operation, for both transmit and receive. It can also be connected to a GPS re- ceiver* to transmit/receive position data. * Compatible with an RS-232 output/NMEA format/ 4800bps/9600 bps N #ALLSIGNSETTING Set the desired h52 vh2 vh2vANDh-9vcall signs to be used for DV operation, as described below. NOTE: )NTHE$2MODE YOUCANSETONLYh-9vCALL sign in the “CS” screen (Call Sign). q Push [DVsDR] to select the DV mode. w Push [MENU] one or more times to display the “M3” screen (Menu 3). s)NTHE$2MODE Push [MENU] once or twice to select the “D1” screen. e Push [CS](F-1) to display the “CS” screen (Call Sign). s9OUCANPUSH;& =TOTOGGLEBETWEENTHECALLSIGNAND the name. r Push [Z](F-1) one or more times to display the h52 vh2 vh2vORh-9vSCREEN t Rotate [MAIN DIAL] to select the desired call sign. s UR : “CQCQCQ,” individual station call signs (U01–U99) or destination repeater call signs* 1 is selected. s29OURACCESSAREAREPEATERSCALLSIGNISSE- lected. s R2 : “NOT USE 1”* 2 or a link/gateway repeater call sign is selected. s-99OUROWNCALLSIGNSISSELECTED-9n-9  s&IRSTSELECTINGTHECALLSIGNGROUPBYPUSHING;43s'20= or [GRP](F-5)* 3 makes it more convenient when “UR,” “R1” or “R2” is displayed. See the right column for de- tails of the repeater call sign group selection. y Push [SET](F-4) to set the selected call sign to be used for DV operation. u Repeat steps r to y to set the other call signs. i Push [Z](F-1) one or more times to return to the “CS” screen. NOTE:9OUCANTOGGLEBETWEENDISPLAYINGTHERE- peater name or the repeater call sign by pushing [NAME](F-4) in the R1 and R2 screens. * 1 ‘/’ is displayed in front of the repeater call sign. The repeater call sign with ‘/’ is used for the gateway CQ calling. * 2 For an area (local) repeater communication only (Link repeater is not used.) * 3 [GRP](F-5) is not used in the DR mode. [CS]/[√] [SET] [MENU][DVDR][MAIN DIAL] CSCD R>CS URDSET M3 CSUR CQCQCQ JA3YUA MY R1 R2NOT USE Ú UR  
UR CLR CQCQCQ EDT NAME GRP UR  
UR CLR JG3YMK EDT NAME GRP UR  
U01 JG3YMK SET GRP Rotate [MAIN DIAL] (OWTOSELECTTHEREPEATERCALLSIGNGROUP Hold down [TSsGRP] or [GRP](F-5)* 3 for 1 second to enter the group selection mode. Then rotate [MAIN DIAL] to select the desired group. After selecting, PUSH;43s'20=OR;'20=&  * 3 to display the re- peater call signs in the group. Or, you can select the repeater group using the key- pad key. - Only repeaters assigned to groups are selectable. !BOUTTHE4IME /UT4IMERFUNCTION The IC-9100 has a Time-Out Timer function for digi- tal repeater operation. The timer limits a continuous transmission to approximately 10 minutes. Warning beeps will sound approximately 30 seconds before time-out and then again immediately before time-out. Be sure to turn ON the function before operating in the digital mode. (p. 162) 94 8 DV MODE OPERATION 8 N2ECEIVINGA$ 34!2REPEATER When the IC-9100 receives a signal from a D-STAR repeater, it receives four call signs: the calling station’s call sign, the called station’s call sign, the R1 repeater call sign (the repeater that receives a signal from the calling station on the uplink frequency), and the R2 re- peater call sign (the repeater that transmits a signal ONTHEDOWNLINKFREQUENCY 9OUCANCOPYTHERECEIVED call signs into your radio, and reply to the call. Station AStation B Repeater 446.000 MHz 445.400 MHz 445.400 MHz 446.000 MHz Uplink Downlink (Transmit frequency) (Receive frequency) s0RESETTING q Select the desired frequency band. (p. 35) w Push [VFO/MEMO] to select the VFO mode. e Push [A/B] once or twice to select VFO A. r Set the desired repeater transmit (downlink) fre- quency. (p. 37) s!DJUSTTHEOUTPUTPOWER IFDESIREDP t Push [MENU] to display the “M1” screen (Menu 1). y Hold down [DUP](F-2) for 1 second to turn ON the One-touch repeater function. sh4vANDh$50nvAPPEAR s4HEREPEATERRECEIVEUPLINK FREQUENCYAPPEARSATTHE bottom of the function display. u Push [DUP](F-2) once or twice to switch the offset to the desired direction. sh$50nvORh$50 vAPPEARS s7HENTHE!UTO2EPEATERFUNCTIONISINUSE THISSELEC- tion is not necessary (Only U.S.A. and Korean versions). (p. 67) i Push [DVsDR] to select the DV mode. (p. 43) s“DV” appears. sh4vDISAPPEARS o When a signal is received, the calling station’s call sign is displayed on the LCD. s)FTHECALLINGSTATIONHASPROGRAMMEDANOTEORMES- sage, it is displayed after the call sign. See the next page to view the received call sign. To reply to the calling station, see page 96. [VFO/MEMO] [A/B] [DVDR] “T” disappears Appears M1 DUPAGCAFC TON SCP 445.40000 M1 DUPAGCAFC DSQ SCP 445.40000 Appears Uplink frequency Appears 95 8 DV MODE OPERATION N2ECEIVEDCALLSIGNS When a call is received in the DV mode, the calling sta- tion and repeater call signs being used can be stored in the received call record. The stored call signs can be displayed in the following manner. Up to 20 calls can be stored. D$ESIREDCALLRECORDDISPLAY q Push [DVsDR] to select the DV mode. w Push [MENU] one or more times to display the “M3” screen (Menu 3). s)NTHE$2MODE PUSH;-%.5=ONCEORTWICETOSELECT the “D1” screen. e Push [CD](F-2) to display the “CD” screen (Call Re- cord). r Rotate [MAIN DIAL] to select the desired record channel (RX01 to RX20). s(OLDDOWN;#,2=&  FORSECONDTOCLEARTHESELECTED record channel. t Push [Z](F-1) one or more times to display the call record. s#!,,%2 4HECALLINGSTATIONSCALLSIGN s !FOURCHARACTERNOTEFROMTHESTATION that made the call. s#!,,%$ 4HECALLSIGNOFTHESTATIONTHATWAS called, or “CQCQCQ.” s28204 4HECALLSIGNOFTHEREPEATERTHECALL- ing station accessed, or the call sign of the gateway repeater the c…

Text truncated - open the document above for the full version.

UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 FCC 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R Korea KCC-RRL CA2049 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] January 24, 2011 Ultratech Engineering Labs, Inc. 3000 Bristol Circle Oakville, Ontario L6H 6G4 Subject: Certification Testing in Accordance with FCC CFR 47, Part 15, Subpart B - Scanning Receivers Applicant: ICOM Incorporated Product: HF/VHF/UHF Transceiver Model: IC-9100 FCC ID: AFJ318300 Dear Sir/Madam: As appointed agent for ICOM Incorporated, we submit the application for certification of the above product. Please review all files uploaded to your electronic filing site. If you have any queries, please do not hesitate to contact us by our TOLL FREE number: OUR TELEPHONE NO.: 1-877-747-6381 Yours truly, Dan Huynh Dan Huynh Authorized Agent

HF/VHF/UHF Transceiver Model No.: IC-9100 FCC ID: AFJ318300 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka, Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Part 15, Subpart B, Scanning Receivers UltraTech's File No.: ICOM-266F15B121 This Test report is Issued under the Authority of Tri M. Luu, BASc Vice President of Engineering UltraTech Group of Labs Date: January 24, 2011 Report Prepared by: Dan Huynh Issued Date: January 24, 2011 Tested by: Wei Wu, Phuong Ngo and Satish Patel Test Dates: January 14, 19 & 21, 2011  The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected.  This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] FCC Korea KCC-RRL 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R CA2049 FCC Part 15, Subpart B, Section 15.121 Contents i HF/VHF/UHF Transceiver, M/N: IC-9100 FCC ID: AFJ318300 ULTRATECH GROUP OF LABS File #: ICOM-266F15B121 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 24, 2011 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................................1 1.1. SCOPE ............................................................................................................................................................................................1 1.2. RELATED SUBMITTAL(S)/GRANT(S).......................................................................................................................................1 1.3. NORMATIVE REFERENCES .......................................................................................................................................................1 EXHIBIT 2. PERFORMANCE ASSESSMENT .................................................................................................................................2 2.1. CLIENT INFORMATION ..............................................................................................................................................................2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION.................................................................................................................2 2.3. EUT’S TECHNICAL SPECIFICATIONS......................................................................................................................................3 2.4. LIST OF EUT’S PORTS.................................................................................................................................................................3 2.5. ANCILLARY EQUIPMENT ..........................................................................................................................................................4 2.6. TEST SETUP BLOCK DIAGRAM ................................................................................................................................................5 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS...................................................6 3.1. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS.................................................................6 EXHIBIT 4. SUMMARY OF TEST RESULTS..................................................................................................................................7 4.1. LOCATION OF TESTS..................................................................................................................................................................7 4.2. APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS ..................................................................................7 4.3. MODIFICATIONS REQUIRED FOR COMPLIANCE .................................................................................................................7 EXHIBIT 5. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS ..................................................8 5.1. TEST PROCEDURES ....................................................................................................................................................................8 5.2. MEASUREMENT UNCERTAINTIES ..........................................................................................................................................8 5.3. MEASUREMENT EQUIPMENT USED .......................................................................................................................................8 5.4. POWER LINE CONDUCTED EMISSIONS [§ 15.107(a)]............................................................................................................9 5.5. RECEIVER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§15.111(a)] .................................. 12 5.6. SPURIOUS/HARMONIC RADIATED EMISSIONS FROM RECEIVER AND CLASS B UNINTENTIONAL RADIATORS (DIGITAL DEVICES) [§ 15.109(a)]..................................................................................................................... 28 5.7. REQUIREMENTS FOR SCANNING RECEIVERS [§ 15.121] ............................................................................ ...................... 36 5.8. SCANNING RECEIVERS CELLULAR BAND REJECTION [§ 15.121(b)].............................................................................. 39 EXHIBIT 6. TEST EQUIPMENTS LIST.......................................................…

Text truncated - open the document above for the full version.

ANNEX 1 – TEST SETUP PHOTOS Icom Incorporated HF/VHF/UHF Transceiver, Model IC-9100 FCC ID: AFJ318300 A1 - 1 Power Line Conducted Emission ANNEX 1 – TEST SETUP PHOTOS Icom Incorporated HF/VHF/UHF Transceiver, Model IC-9100 FCC ID: AFJ318300 A1 - 2 Power Line Conducted Emission ANNEX 1 – TEST SETUP PHOTOS Icom Incorporated HF/VHF/UHF Transceiver, Model IC-9100 FCC ID: AFJ318300 A1 - 3 Radiated Emission at 3m Distance ANNEX 1 – TEST SETUP PHOTOS Icom Incorporated HF/VHF/UHF Transceiver, Model IC-9100 FCC ID: AFJ318300 A1 - 4 Radiated Emission at 3m Distance