AFJ328602UHF Transceiver

INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. UHF TRANSCEIVERS iF4000 Series VHF TRANSCEIVERS iF3000 Series i FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F3001/ IC-F3003/IC-F3006/IC-F3008 VHF TRANSCEIVERS and the IC-F4001/IC-F4003/IC-F4006/IC-F4008 UHF TRANSCEIVERS. EXPLICIT DEFINITIONS WORDDEFINITION RDANGER Personal death, serious injury or an explo- sion may occur. RWARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo- rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. ii PRECAUTIONS CAUTION: NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical. CAUTION: NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION: NEVER short the terminals of the battery pack. CAUTION: NEVER use non-Icom battery packs/chargers, to pre- vent the loss of the transceiver’s good performance and warranty. DO NOT push [PTT] when not actually intending to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below –30°C (+22°F) or above +60°C (+140°F). DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. KEEP the transceiver away from heavy rain, and never immerse it in the water. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. MAKE SURE to turn the transceiver power OFF before con- necting the supplied/optional equipment. iii FCC INFORMATION • FOR CLASS B UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications to this device, not ex- pressly approved by Icom Inc., could void your authority to oper- ate this transceiver under FCC regulations. iv TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 FOREWORD ........................................................................................i EXPLICIT DEFINITIONS ......................................................................i PRECAUTIONS ...................................................................................ii FCC INFORMATION ...........................................................................iii TABLE OF CONTENTS ......................................................................iv 1 ACCESSORIES .........................................................................1–4 ■ Supplied accessories ..................................................................1 ■ Accessory attachments ..............................................................1 2 PANEL DESCRIPTION ............................................................5–11 ■ Front, top and side panels ..........................................................5 ■ LED indicator ..............................................................................7 ■ Programmable function keys ......................................................8 3 BASIC OPERATION ..............................................................12–22 ■ Turning power ON .....................................................................12 ■ Channel selection .....................................................................13 ■ Call procedure ..........................................................................14 ■ Receiving and transmitting .......................................................15 ■ Setting the microphone gain .....................................................18 ■ Setting the squelch level ...........................................................19 ■ Priority A channel selection ......................................................19 ■ MDC 1200 system operation ....................................................20 ■ Emergency Call ........................................................................21 ■ Lone Worker Emergency Call ...................................................22 4 BATTERY CHARGNING ........................................................23–30 ■ Caution (for BP-265 li-ion battery) ..........................................23 ■ Caution (for the BP-264 ni-…

Text truncated - open the document above for the full version.

Thank you for purchasing the FA-SC61UC UHFANTENNA. Please read these instructions thoroughly before using the FA-SC61UC. 400 MHz 420 MHz 440 MHz 460 MHz 480 MHz 500 MHz 520 MHz 380 MHz 360 MHz 0 Antenna cap FA-SC61UC The optimum bandwidth is ±8% of the tuned frequency. For optimum performance tune to the center transmit frequency of the radio. Cutting Instructions qAlign the bottom of the anten- na onto the 0 position of the cutting guide diagram at left. wMark the antenna at the length corresponding to the desired frequency to be tuned. FA-SC61UC A-6532K-1EX-wPrinted in Japan ©2006-2009 Icom Inc. eCut the antenna to the marked length. • Use a wire cutter that can cut at least 1.2 mm (d) of piano wire. rApply adhesiveto the top of the antenna and attach the supplied antenna cap. • Use of Cemedine Co. Super-X No. 8008 black (Icom parts number: 8950002910) or similar is recommended. Antenna Cutting Chart NOTE: A n t e n n a c a p m u s t b e i n s e r t e d a f t e r c u t t i n g t h e e l e m e n t o t h e r w i s e wa t e r immersion makes the element damaged. Center frequency (MHz) Length (mm) 185 175 165 156 148 142 136 129 125 360 380 400 420 440 460 480 500 520 CAUTION: Making antenna cuts at other than the prescribed lengths specified could void the user's author ity to operate the equipment.

UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R Korea KCC-RRL CA2049 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] March 5, 2010 Ultratech Engineering Labs, Inc. 3000 Bristol Circle Oakville, Ontario L6H 6G4 Subject: Equipment Authorization under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 450-512 MHz (25 KHz and 12.5 KHz Channel Spacings). Applicant: ICOM Incorporated Product: UHF Transceiver Model: IC-F4001 FCC ID: AFJ328602 Dear Sir/Madam, As appointed agent for ICOM Incorporated, we would like to submit the application to Federal Communications Commission for certification of the above product. Please review all files uploaded to your electronic filing site. If you have any queries, please do not hesitate to contact us by our TOLL FREE number: OUR TELEPHONE NO.: 1-877-747-6381 Yours truly, Santhosh Fernandez Authorized Agent Santhosh Fernandez

W AR NING Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by indi- viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre- quency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3-1992), IEEE Recom - mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. • The accessories (antennas, batteries, belt clips, speaker-micro- phone, etc. that is listed on pages 32–34) are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. C AU TION To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu- pational use, always adhere to the following guide- lines: 38 7 SAFETY TRAINING INFORMATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 39 7 SAFETY TRAINING INFORMATION • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo- sure compliance requirements to be exceeded. The radio is trans- mitting when the “LED indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch or VOX function. • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to en- sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual- ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as- sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro- magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R Korea KCC-RRL CA2049 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] March 19, 2010 ICOM Incorporated 2380 116 Avenue North East BELLEVUE WASHINGTON, 98004 USA Attn.: Mr. Masaaki Takahashi Subject: Verification Testing in accordance with SAR (Specific Absorption Rate) requirements using guidelines established in: IEEE C95.1-1992, FCC OET Bulletin 65 (Supplement C) Industry Canada RSS-102 (Issue 2) Product: UHF Transceivers Model: IC-F4001 Dear Mr. Takahashi The product sample has been tested in accordance with SAR (Specific Absorption Rate) requirements using guidelines established in IEEE Standard C95.1, FCC OET Bulletin 65 (Supplement C), Industry Canada RSS-102 (Issue 2) ), and the results and observation were recorded in the engineering report, Our File No.: ICOM-229Q-SAR Enclosed you will find a copy of the engineering report. If you have any queries, please do not hesitate to contact us. Yours truly, Tri Minh Luu, P.Eng Vice President - Engineering Encl. March 19, 2010 ICOM Incorporated 1-132, Kamiminami, Harano-ku Osaka, Japan, 547-0003 File No.: ICOM-229Q-SAR NOT TRANSFERABLE This verification certificate is hereby issued to the named GRANTEE to confirm compliance and is VALID ONLY for the equipment identified hereon for use under the rules and regulations listed below: GRANTEE’S NAME: PRODUCT UNDER TEST: MODEL NO.: FCC ID: OPERATING FREQUENCY RANGE: RATED RF OUTPUT POWER: DEVICE CATEGORY: EXPOSURE CATEGORY: SOURCE-BASED (USAGE-BASED) TIME-AVERAGING: MAX. PEAK SPATIAL-AVERAGE SAR 1G : ICOM Incorporated UHF Transceivers IC-F4001 AFJ328602 450~512 MHz 4 W conducted Portable Occupational/Controlled 50 % for PTT device 3.88 W/Kg for head configuration 6.40 W/Kg for body configuration REFERENCED STANDARDS: SAR (Specific Absorption Rate) requirements using guidelines established in IEEE C95.1-1992, FCC OET Bulletin 65 (Supplement C Edition 01-01) and Industry Canada RSS-102 (Issue 2) UltraTech Group of Labs 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected] , Email: [email protected] Korea KCC-RRL 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R CA2049 UHF Transceivers Model No.: IC-F4001 Tested For ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka, Japan, 547-0003 In accordance with SAR (Specific Absorption Rate) Requirements using guidelines established in IEEE C95.1-1992, FCC OET Bulletin 65 (Supplement C) and Industry Canada RSS-102 (Issue 2) UltraTech’s File No.: ICOM-229Q-SAR This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: March 19, 2010 Report Prepared by: Steven Lu Tested by: Steven Lu Issued Date: March 19, 2010 Test Dates: March 5~March 17, 2010 The results in this Test Report apply only to the sample(s) tested, which has been randomly selected. UltraTech Group of Labs 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected] , Email: [email protected] Korea KCC-RRL 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R CA2049 SPECIFIC ABSORPTION RATE (SAR) Contents i IEEE C95.1-1992, FCC OET Bulletin 65 (Supplement C) UHF Transceivers M/N: IC-F4001 FCC ID: AFJ328602 ULTRATECH GROUP OF LABS File #: ICOM-229Q-SAR 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 March 19, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA ) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE............................................................................................................................................................................ 1 1.2. REFERENCES ............................................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT.................................................................................................................. 2 2.1. CLIENT AND MANUFACTURER INFORMATION .................................................................................................. 2 2.2. DEVICE UNDER TEST (D.U.T.) DESCRIPTION .......................................................................................................... 2 2.2.1. Photograph of D.U.T (IC-F4001) ........................................................................................................................... 3 2.3. LIST OF D.U.T.’S ACCESSORIES: .............................................................................................................................. 4 2.3.1. Li-ion Chargeable Battery (M/N: BP-265) ............................................................................................................. 4 2.3.2. Ni-MH Chargeable Battery (M/N: BP-264) ........................................................................................................... 4 2.3.3. BP-263 Alkaline Battery Case for 6*AA (LR6)..........................................................................................…

Text truncated - open the document above for the full version.

UHF Transceiver Model No.: IC-F4001 FCC ID: AFJ328602 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: ICOM-229F90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: March 2, 2010 Report Prepared by: Santhosh Fernandez Issued Date: March 2, 2010 Tested by: Wayne Wu Test Dates: February 19, 22-25, 2010 ƒ The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. ƒ This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech Group of Labs 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected] , Email: [email protected] Korea KCC-RRL 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R CA2049 FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Contents i UHF Transceiver, Model IC-F4001 FCC ID: AFJ328602 ULTRATECH GROUP OF LABS File #: ICOM-229F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 March 2, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE............................................................................................................................................................................ 1 1.2. RELATED SUBMITTAL(S)/GRANT(S) ...................................................................................................................... 1 1.3. NORMATIVE REFERENCES....................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT.................................................................................................................. 2 2.1. CLIENT INFORMATION ............................................................................................................................................. 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION................................................................................................. 2 2.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................... 3 2.4. LIST OF EUT’S PORTS................................................................................................................................................. 4 2.5. GENERAL TEST SETUP..................................................................................................................................................... 4 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS................................... 5 3.1. CLIMATE TEST CONDITIONS ................................................................................................................................... 5 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS.................................................. 5 EXHIBIT 4. SUMMARY OF TEST RESULTS .................................................................................................................. 6 4.1. LOCATION OF TESTS ................................................................................................................................................. 6 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS............................................................................ 6 4.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ............................................ 6 EXHIBIT 5. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .................................. 7 5.1. TEST PROCEDURES .................................................................................................................................................... 7 5.2. MEASUREMENT UNCERTAINTIES.......................................................................................................................... 7 5.3. MEASUREMENT EQUIPMENT USED ....................................................................................................................... 7 5.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ............................................ 7 5.5. RF POWER OUTPUT [§§ 2.1046 & 90.205] ................................................................................................................. 8 5.6. AUDIO FREQUENCY RESPONSE [§§ 2.1047(A) & 90.242(B)(8)] ............................................................................. 9 5.7. MODULATION LIMITING [§§ 2.1047 (B) & 90.210] ................................................................................................ 16 5.8. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 90.209 & 90.210] ...................................................... 21 5.9. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§§ 2.1051, 2.1057 & 90.210]...................................................................................................................................................................................... 41 5.10. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§§ 2.1053, 2.1057 & 90.210] ................. 54 5.11. FREQUENCY STABILITY [§§ 2.1055 & 90.213] .................................................................................................. 58 5.12. TRANSIENT FR…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode > ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF Transceiver, M/N: IC-F4001 FCC ID: AFJ328602 < Radiated emission test, Tx mode >