AFJ332800VHF Transceiver

INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. UHF TRANSCEIVERS iF4100D Series VHF TRANSCEIVERS iF3100D Series Limited functions only i FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL— This instruc- tion manual contains important operating instructions for the IC- F3101D/IC-F3103D/IC-F3106D VHF TRANSCEIVERS and the IC-F4101D/IC-F4103D/IC-F4106D UHF TRANSCEIVERS. EXPLICIT DEFINITIONS WORDDEFINITION RDANGER! Personal death, serious injury or an explo- sion may occur. RWARNING! Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo- rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. ii FCC INFORMATION • FOR CLASS B UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. iii PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. R DANGER! NEVER Use and charge only specified Icom bat- tery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use. R WARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention—anything less may result in an accident. CAUTION: MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the trans- ceiver. DO NOT operate the transceiver near unshielded electrical blast- ing caps or in an explosive atmosphere. DO NOT push [PTT] when not actually intending to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below –30°C (+22°F) or above +60°C (+140°F). iv PRECAUTIONS DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceiver surfaces. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods of time. KEEP the transceiver away from heavy rain, and never immerse it in the water. The transceiver meets IP54* requirements for dust- protection and splash resistance. However, once the transceiver has been dropped, dust-protection and splash resistance cannot be guaranteed because of possible damage to the transceiver’s case or the waterproof seal. * Only when the battery pack and jack cover are attached. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or batteries from the trans- ceiver when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced. MAKE SURE to turn the transceiver power OFF before connect- ing the supplied/optional equipment. v VOICE CODING TECHNOLOGY The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Com- munications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166. vi TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 FOREWORD .................................................................…

Text truncated - open the document above for the full version.

Thank you for purchasing the FA-SC61VC VHFANTENNA. Please read these instructions thoroughly before using the FA-SC61VC. 0 145 MHz 150 MHz 155 MHz 160 MHz 165 MHz 170 MHz 175 MHz 140 MHz 136 MHz Antenna cap FA-SC61VC The optimum bandwidth is ±3% of the tuned frequency. For optimum performance tune to the center transmit frequency of the radio. Cutting Instructions qAlign the bottom of the anten- na onto the 0 position of the cutting guide diagram at left. wMark the antenna at the length corresponding to the desired frequency to be tuned. FA-SC61VC A-6532K-1EX-wPrinted in Japan eCut the antenna to the marked length. • Use a wire cutter that can cut at least 1.2 mm (d) of piano wire. rApply adhesiveto the top of the antenna and attach the supplied antenna cap. • Use of Cemedine Co. Super-X No. 8008 black (Icom parts number: 8950002910) or similar is recommended. T h e a n t e n n a c a n b e u s e d a t i t s o r iginal length for this frequency. No tuning (cutting) is necessary. * ©2006-2009 Icom Inc. Antenna Cutting Chart Center frequency (MHz) Length (mm) 174* 169 163 157 151 146 141 137 133 136 140 145 150 155 160 165 170 175 NOTE: A n t e n n a c a p m u s t b e i n s e r t e d a f t e r c u t t i n g t h e e l e m e n t o t h e r w i s e wa t e r immersion makes the element damaged. CAUTION: Making antenna cuts at other than the prescribed lengths specified could void the user's author ity to operate the equipment.

November 1, 2010 Ultratech Engineering Labs, Inc. 3000 Bristol Circle Oakville, Ontario L6H 6G4 Subject: Equipment Authorization under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 136-174 MHz (25 KHz, 12.5 KHz and 6.25 KHz Channel Spacings). Applicant: ICOM Incorporated Product: VHF Transceivers Model: IC-F3101D FCC ID: AFJ332800 Dear Sir/Madam, As appointed agent for ICOM Incorporated, we would like to submit the application to you for FCC certification of the above product. Please review all files uploaded to your electronic filing site. If you have any queries, please do not hesitate to contact me. Yours truly, Dharmajit Solanki Dharmajit Solanki Authorized Agent UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 FCC 91038 1309 46390-2049 NVLAP Lab Code 200093-0 SL2-IN-E-1119R Korea KCC-RRL CA2049 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 W ebsite: www.ultratech-labs.com

Serial Plate

WARNING Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by indi- viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre- quency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3-1992), IEEE Recom- mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. • The accessories (antennas, batteries, belt clips, speaker-micro- phone, etc. that is listed on pages 35–37) are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. CAUTION To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu- pational use, always adhere to the following guide- lines: 41 7 SAFETY TRAINING INFORMATION 42 7 SAFETY TRAINING INFORMATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo- sure compliance requirements to be exceeded. The radio is trans- mitting when the “LED indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch or VOX function. • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 35 when attaching the radio to your belt, etc., to en- sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual- ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as- sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro- magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

VHF Transceivers Model No.: IC-F3101D FCC ID: AFJ332800 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: ICOM-256F90 This Test report is Issued under the Authority of Tri M. Luu, B.A.Sc, Vice President of Engineering UltraTech Group of Labs Date: November 1, 2010 Report Prepared by: Steven (Xu Tian) Lu Issued Date: November 1, 2010 Tested by: Wayne Wu, RFI/EMI Technician Test Dates: October 5~20, 2010  The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected.  This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech Group of Labs 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected] , Email: [email protected] FCC Korea KCC-RRL 91038 1309 46390-2049 NVLAP Lab Code 200093-0 SL2-IN-E-1119R CA2049 FCC PARTS 2 & 90, SUBPART I, NON-BROADCAST RADIO TRANSCEIVERS Contents i VHF Transceivers, Model IC-F3101D FCC ID: AFJ332800 ULTRATECH GROUP OF LABS File #: ICOM-256F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 November 1, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE............................................................................................................................................................................ 1 1.2. RELATED SUBMITTAL(S)/GRANT(S) ...................................................................................................................... 1 1.3. NORMATIVE REFERENCES ...................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT.................................................................................................................. 2 2.1. CLIENT INFORMATION ............................................................................................................................................. 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ................................................................................................ 2 2.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................... 3 2.4. LIST OF EUT’S PORTS ................................................................................................................................................ 4 2.5. GENERAL TEST SETUP .............................................................................................................................................. 4 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS................................... 5 3.1. CLIMATE TEST CONDITIONS................................................................................................................................... 5 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS ................................................ 5 EXHIBIT 4. SUMMARY OF TEST RESULTS .................................................................................................................. 6 4.1. LOCATION OF TESTS ................................................................................................................................................. 6 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS........................................................................... 6 4.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES .......................................... 6 EXHIBIT 5. TEST DATA...................................................................................................................................................... 7 5.1. RF POWER OUTPUT [§ 2.1046 & 90.205] .................................................................................................................. 7 5.2. RF EXPOSURE REQUIREMENTS [§ 1.1310 & 2.1091]............................................................................................. 8 5.3. AUDIO FREQUENCY RESPONSE [§ 2.1047(A) & 90.242(B)(8)]............................................................................. 9 5.4. MODULATION LIMITING [§ 2.1047 (B) & 90.210] ................................................................................................ 14 5.5. OCCUPIED BANDWIDTH & EMISSION MASK [§ 2.1049, 90.209 & 90.210] ...................................................... 19 5.6. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§2.1051, 2.1057 & 90.210] .......................................................................................................................................................................... 57 5.7. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 2.1053, 2.1057 & 90.210]...................... 74 5.8. FREQUENCY STABILITY [§ 2.1055 & 90.213] ....................................................................................................... 78 5.9. TRANSIENT FREQUENCY BEHAVIOR [§ 90.214] ................................................................................................ 80 EXHIBIT 6. TEST INSTRUMENTS & MEASUREMENT UNCERTAINTY (K=2, 95% CONFIDENCE LEVEL) 88 RADIATED EMISSION MEASUREMENT UNCERTAINTY.............................................................................................. 88 EXHIBIT 7. TEST EQUIPMENTS LIST ...…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated VHF Mobile Transceiver, M/N: IC-3101D FCC ID: AFJ332800, IC: 202D-332800 Plot #1: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated VHF Mobile Transceiver, M/N: IC-3101D FCC ID: AFJ332800, IC: 202D-332800 Plot #2: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated VHF Mobile Transceiver, M/N: IC-3101D FCC ID: AFJ332800, IC: 202D-332800 Plot #3: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated VHF Mobile Transceiver, M/N: IC-3101D FCC ID: AFJ332800, IC: 202D-332800 Plot #4: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated VHF Mobile Transceiver, M/N: IC-3101D FCC ID: AFJ332800, IC: 202D-332800 Plot #5: Rx Radiated Emission Test Setup