AFJ370601UHF FM Repeater

INSTRUCTION MANUAL VHF FM REPEATER iFR5200H iFR6200H UHF FM REPEATER This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. i IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the re- peater. SAVE THIS INSTRUCTION MANUAL– This manual contains important safety and operating in- structions for the IC-FR5200H/IC-FR6200H v h f/u h f f m r e p e at e r s. EXPLICIT DEFINITIONS WORDDEFINITION RWARNING! Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. SUPPLIED ACCESSORIES The following accessories are supplied. R WARNING HIGH VOLTAGE! NEVER at- tach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. R WARNING HIGH VOLTAGE! NEVER install the antenna at any place that person touch the an- tenna easily during transmission. This may result in an electrical shock or burn. R WARNING! NEVER apply AC to the DC power connector on the repeater rear panel. This could cause a fire or damage the repeater. R WARNING! NEVER apply more than 16 V DC to the DC power connector on the repeater rear panel. This could cause a fire or damage the repeater. R WARNING! NEVER reverse the DC power cable polarity when connecting to a power source. This could cause a fire or damage the repeater. CAUTION: NEVER let metal, wire or other objects touch any internal part or connectors on the rear panel of the repeater. This may result in an electric shock. CAUTION: NEVER expose the repeater to rain, snow or any liquids. DO NOT operate or place the repeater in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F). Be aware that temperatures can exceed 80°C (+176°F), resulting in permanent damage to the repeater if left there for extended periods. DO NOT place the repeater in excessively dusty en- vironments or in direct sunlight. DO NOT put anything on top of the repeater. This will obstruct heat dissipation. BE CAREFUL! The heatsink will become hot when operating the repeater continuously for long periods. BE CAREFUL! If a linear amplifier is connected, set the repeater’s RF output power to less than the linear amplifier’s maximum input level, otherwise, the linear amplifier will be damaged. Use Icom microphones only (optional). Other manu- facturer’s microphones have different pin assignments, and may damage the repeater. Place the repeater in a secure place to avoid inadver- tent use by children. For U.S.A. only CAUTION: Changes or modifications to this re- peater, not expressly approved by Icom Inc., could void your authority to operate this repeater under FCC regulations. PRECAUTIONS Handles For handles attachment For the connector SpacersHexagon wrench Screws ScrewsHolder Connector Function name stickers* 1 Rack KEY SEAL Used for labelling the program- mable function keys according to their assinged functions. * 1 Square fuse (FGB01 30A) ii Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. FORWARD Thank you for choosing this Icom repeater. The IC- FR5200H/IC-FR6200H v h f/u h f f m r e p e at e r s are designed and built with Icom’s state of the art technol- ogy and craftsmanship. With proper care, this product should provide you with years of trouble-free opera- tion. We want to take a couple of moments of your time to thank you for making the IC-FR5200H/IC-FR6200H your repeater of choice, and hope you agree with Icom’s philosophy of “technology first.” Many hours of research and development went into the design of your IC-FR5200H/IC-FR6200H. D FEATURES m Built-in 5-Tone, DTMF encoder & decoder Multiple signaling systems are equipped as stan- dard. These systems are fully compatible with Icom F-series radios. m DTMF remote control capability You can control the repeater from a remote location over the air or over a phone line with DTMF. m D-Sub 25 pin ACC port equipped You can use the optional equipment via the D-sub 25 pin ACC port equipped on the repeater’s rear panel. m Other features - Wide frequency coverage <VHF> IC-FR5200H: 136 to 174 MHz <UHF> IC-FR6200H: 350 to 400 MHz, 400 to 470 MHz, 450 to 512 MHz, 450 to 520 MHz - PC programmable - 19 inch rack mount - Optional Voice Scrambler Unit (UT-109R/ UT-110R) for base operating mode TABLE OF CONTENTS IMPORTANT ...............................................................i EXPLICIT DEFINITIONS ............................................i SUPPLIED ACCESSORIES.......................................i PRECAUTIONS ..........................................................i FORWARD ................................................................ii TABLE OF CONTENTS ............................................ii SAFETY TRAINING INFORMATION .......................iii 1 PANEL DESCRIPTION .............................1–3 n Front panel ........................................................1 D Function display ............................................2 n Rear panel .........................................................2 D Accessory connector ....................................3 2 INSTALLATION AND CONNECTIONS ....4–6 n Unpacking .........................................................4 n Selecting a location ...........................................4 n Antenna connection ..........................................4 n Front panel connection ......................................5 n Rear panel connection ......................................5 n Power supply connection ..................................6 n Mounting the repeater .......................................6 D Using the supplied handle ..................…

Text truncated - open the document above for the full version.

January 14, 2015 Ultratech Engineering Labs, Inc. 3000 Bristol Circle Oakville, Ontario L6H 6G4 Subject: Equipment Certification under FCC 47 CFR, Parts 2, 22, 74, 80 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 400-406 & 406.1-470 MHz (25 kHz, 12.5 kHz and 6.25 kHz Channel Spacing) Applicant: ICOM Incorporated Product: UHF FM Repeater Model: IC-FR6200H FCC ID: AFJ370601 Dear Sir/Madam: As appointed agent for ICOM Incorporated, we would like to submit the application to you for FCC certification of the above product. Please review all files uploaded to your electronic filing site. Note 1: As declared by the applicant in the attestation letter submitted with this filing, 25kHz channel spacing (16K0F3E) operation of this radio is permanently disabled for Part 90 use as required by FCC mandate. Test performed for 25kHz channel spacing are for parts 22, 74 & 80 certifications only. Note 2: ICOM hereby request FCC to list the entire frequency range from 400-406 & 406.1-470 MHz under FCC rules as per the reasons explained in the attached Frequency Justification letter submitted with this filing. If you have any queries, please do not hesitate to contact us. Yours truly, Dharmajit Solanki Dharmajit Solanki Authorized Agent UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 91038 1309 46390-2049 NVLAP LAB CODE 200093-0 SL2-IN-E-1119R Korea KCC-RRA CA2049 TL363_B TPTDP DA1300 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected]

Photographs of the equipment 1 Front view Rear view Right view Left view Photographs of the equipment 2 Top view Bottom view

Photographs of the equipment 3 Cover off Cover off Photographs of the equipment 4 MAIN-C Side A MAIN-C Side B Photographs of the equipment 5 FRONT Side A FRONT Side B Photographs of the equipment 6 CONNECT Side A CONNECT Side B Photographs of the equipment 7 CONTROL Side A CONTROL Side B

FCC Parts 2, 22, 74, 80 and 90 Subpart I, Non-Broadcast Radio Transceivers Page 95 of 95 UHF FM Repeater, Model: IC-FR6200H FCC ID: AFJ370601 ULTRATECH GROUP OF LABS File #: 15ICOM387_FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 14, 2015 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) 5.13. RF EXPOSURE REQUIREMENTS [§§ 1.1310 & 2.1091] 5.13.1. Limits § 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 6141.63*(100) 6 3.0-30 1842/f4.89/f*(900/f 2 ) 6 30-300 61.40.1631.0 6 300-1500 f/300 6 1500-100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 6141.63*(100) 30 1.34-30 824/f2.19/f*(180/f 2 ) 30 30-300 27.50.0730.2 30 300-1500 f/1500 30 1500-100,000 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Note 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. Note 2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. FCC Parts 2, 22, 74, 80 and 90 Subpart I, Non-Broadcast Radio Transceivers Page 96 of 95 UHF FM Repeater, Model: IC-FR6200H FCC ID: AFJ370601 ULTRATECH GROUP OF LABS File #: 15ICOM387_FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 14, 2015 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) 5.13.2. Method of Measurements Calculation Method of RF Safety Distance : 22 44r EIRP r PG S ⋅ = ⋅ = ππ Where, P: power input to the antenna in mW EIRP: Equivalent (effective) isotropic radiated power. S: power density mW/cm 2 G: numeric gain of antenna relative to isotropic radiator r: distance to centre of radiation in cm S EIRP S PG r ⋅ = ⋅ = ππ44 FCC radio frequency exposure limits may be exceeded at distances closer than r cm from the antenna of this device. 5.13.3. Evaluation of RF Exposure Compliance Requirements Maximum RF Power conducted, P conducted [W]: 50 Maximum Antenna Gain, G[dBi]: 0 Maximum EIRP, P EIRP [W]: 50 User-based time-average for PTT 50% MPE Limit for Occupational/Controlled Exposure, S controlled [mW/cm 2 ]: 1.33 MPE Limit for General Population/Uncontrolled Exposure, S uncontrolled [mW/cm 2 ] 0.267 Calculated RF Safety Distance for Occupational/Controlled Exposure, r safety_controlled [cm]: 55 Calculated RF Safety Distance for General Population/Uncontrolled Exposure, r safety_uncontrolled [cm] 122

UHF FM Repeater Model No.: IC-FR6200H FCC ID: AFJ370601 Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka, Japan, 547-0003 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2, 22, 74, 80 and 90 (Subpart I) UltraTech's File No.: 15ICOM387_FCC90 This Test report is Issued under the Authority of Tri M. Luu, BASc, Vice President of Engineering UltraTech Group of Labs Date: January 14, 2015 Report Prepared by: Dharmajit Solanki Issued Date: January 14, 2015 Tested by: Wei Wu Test Dates: Nov.03 – Dec.15, 2014  The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected.  This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] Korea KCC-RRA 91038 1309 46390-2049 NVLAP LAB CODE 200093-0 SL2-IN-E- 1119R CA2049 TL363_B TPTDP DA1300 FCC Parts 2, 22, 74, 80 and 90 Subpart I, Non-Broadcast Radio Transceivers Contents i UHF FM Repeater, Model IC-FR6200H FCC ID: AFJ370601 ULTRATECH GROUP OF LABS File #: 15ICOM387_FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 14, 2015 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE ............................................................................................................................................................................ 1 1.2. RELATED SUBMITTAL(S)/GRANT(S) ...................................................................................................................... 1 1.3. NORMATIVE REFERENCES ...................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT .................................................................................................................. 2 2.1. CLIENT INFORMATION ............................................................................................................................................. 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ................................................................................................ 2 2.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................... 3 2.4. LIST OF EUT’S PORTS ................................................................................................................................................ 4 2.5. ANCILLARY EQUIPMENT ......................................................................................................................................... 4 2.6. GENERAL TEST SETUP .............................................................................................................................................. 4 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ................................... 5 3.1. CLIMATE TEST CONDITIONS ................................................................................................................................... 5 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS ................................................ 5 EXHIBIT 4. SUMMARY OF TEST RESULTS .................................................................................................................. 6 4.1. LOCATION OF TESTS ................................................................................................................................................. 6 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS........................................................................... 6 4.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES .......................................... 6 EXHIBIT 5. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .................................. 7 5.1. TEST PROCEDURES .................................................................................................................................................... 7 5.2. MEASUREMENT UNCERTAINTIES .......................................................................................................................... 7 5.3. MEASUREMENT EQUIPMENT USED ....................................................................................................................... 7 5.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ........................................... 7 5.5. RF POWER OUTPUT [§§ 2.1046, 22.565, 74.461, 80.215 & 90.205] .......................................................................... 8 5.6. AUDIO FREQUENCY RESPONSE [§ 2.1047(A), 80.213(E) & 90.242(B)(8)] ........................................................... 9 5.7. MODULATION LIMITING [§§ 2.1047 (B), 74.463, 80.213 & 90.210] ..................................................................... 14 5.8. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 74.462, 80.211(F), 90.209 & 90.210] ...................... 19 5.9. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§ 2.1051, 2.1057, 22.359, 80.211(F)(3) & 90.210].................................................................................................................................... 69 5.10. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§§ 2.1053, 2.1057, 22.359, 80.211(F)(3) & 90.210] .....................................................…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF FM Repeater, M/N: IC-FR6200H FCC ID: AFJ370601, IC: 202D-370601 Plot #1: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF FM Repeater, M/N: IC-FR6200H FCC ID: AFJ370601, IC: 202D-370601 Plot #2: Tx Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated UHF FM Repeater, M/N: IC-FR6200H FCC ID: AFJ370601, IC: 202D-370601 Plot #3: Tx Radiated Emission Test Setup