AFJ384612UHF P25 Transceiver

RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. RWARNING! NEVER operate the transceiver during a lightning storm. It may result in an electric shock, cause a fire or damage the transceiver. Always disconnect the power souce and antenna before a storm. RWARNING! NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This could damage the transceiver. RWARNING! NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. RWARNING! NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. CAUTION: Confirm that all connectors and jacks are dry and clean before attachment. Exposing them to dust or water will result in serious damage to the transceiver. CAUTION: The transceiver will become hot when operating continuously for long periods. DO NOT place or leave the transceiver in areas with temperatures below –30°C (–22°F) or above 60°C (140°F), or in areas subject to direct sunlight, such as the dashboard. DO NOT place or leave the transceiver in direct sunlight or in areas outside of the specified temperature range: –30°C (–22°F) ~ 60°C (140°F) DO NOT operate the transceiver without running the vehicle’s engine. The vehicle’s battery will quickly run out when the transceiver transmits while the vehicle’s engine is OFF. DO NOT place or leave the transceiver in excessively dusty environments. DO NOT place the transceiver against walls. Otherwise heat dissipation will be obstructed. DO NOT use harsh solvents such as Benzine or alcohol when cleaning, as they damage the transceiver’s surfaces. DO NOT block the air vent when installing the transceiver. This transceiver has an air vent on the bottom panel of the transceiver to meet the IP55 requirements. Use the specified microphone only. Other microphones have different pin assignments and may damage the radio. Place the radio in a secure place to avoid inadvertent use by unauthorized persons. Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. • For compliance with FCC and IC RF Exposure Requirements, the transmitter antenna installation shall comply with the following three conditions: 1. The transmitter antenna gain shall not exceed 0 dBi. 2. IC-F7510: The antenna is required to be located outside of a vehicle and kept at a distance of 57 centimeters (23 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 57 centimeters (23 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 57 centimeters (23 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 2. IC-F7520: The antenna is required to be located outside of a vehicle and kept at a distance of 42 centimeters (17 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 42 centimeters (17 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 42 centimeters (17 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 2. IC-F7540: The antenna is required to be located outside of a vehicle and kept at a distance of 31 centimeters (12 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 31 centimeters (12 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 31 centimeters (12 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 3. IC-F7510: Transmit only when people outside the vehicle are at least the recommended minimum distance of 136 centimeters (54 inches) away from the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed externally-mounted antenna to satisfy the RF exposure requirements in the applicable RF exposure compliance standards. 3. IC-F7520: Transmit only when people outside the vehicle are at least the recommended minimum distance of 119 centimeters (47 inches) away from the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed externally-mounted antenna to satisfy the RF exposure requirements in the applicable RF exposure compliance standards. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A7383D-1EX-3 Printed in Japan © 2017–2018 Icom Inc. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: •Force majeure, including, but not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. •The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. FCC INFORMATION This equipment has bee…

Text truncated - open the document above for the full version.

For USA Only Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: Trade Name : ICOM Model Name: : IC-F7520 Responsible party: Company name : Icom America Inc. Address : 12421 Willows Road NE Kirkland, WA 98034 U.S. Contact Information: 800-USA-ICOM (800-872-4266) Monday - Friday 7AM to 5PM PST FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

FCC TC APE C SL Ko 300 0 Oak Can Tel.: Fax.: Website: w w Email: vic CB & ISED C EC TEL CA0001 1309 A 0001/2049 AT-1945 2-IN-E-1119R rea KCC-RRA CA0001 0 Bristol Circle, kville, Ontario, nada L6H 6G4 (905) 829-1570 (905) 829-8050 ww.ultratech-labs c@ultratech-labs. De c Ultr 300 Oak L6H Su b App Pro Mo FC C De a As for fili n No t cha req 80 If y o Yo u San San Aut CB s.com .com cember 14, 2 ratech Engin 00 Bristol Circ kville, Ontario H 6G4 bject: plicant: oduct: del: C ID: ar Sir/Madam appointed ag FCC certifica ng site. te 1: As decla annel spacing uired by FCC certifications ou have any q urs truly, nthosh Fernand nthosh Ferna thorized Agen 022 neering Labs cle o Certificatio n and 90 (Sub Frequency B ICOM Incorp UHF P25 Tra IC-F7520 AFJ384612 m: gent for ICOM ation of the ab ared by the ap g (16K0F3E) o C mandate. Te only. queries, pleas dez ndez nt s, Inc. n Testing in a part I) - Non- Band 450-512 porated ansceiver M Incorporate bove product. pplicant in the operation of th est performed se do not hes accordance w -Broadcast R 2MHz (25 kH ed, we would Please revi e e attestation le his radio is pe d for 25kHz ch sitate to conta with FCC 47 Radio Transc z, 12.5 kHz C like to submit ew all files up etter submitte ermanently di hannel spacin act us. CFR, Parts 2 ceivers Oper Channel Spa t the applicati loaded to yo u ed with this fil sabled for P a ng are for par 2, 22, 74, 80 rating in the cing) on to you ur electronic ing, 25kHz art 90 use as rts 22, 74 &

IC-F7520 FRONT SIDE IC-F7520 REAR SIDE IC-F7520 LEFT SIDE IC-F7520 RIGHT SIDE IC-F7520 TOP SIDE IC-F7520 BOTTOM SIDE

Remote Head Connection (1) Remote Head Connection (2) IC-F7520 FRONT SIDE IC-F7520 Rear SIDE IC-F7520 TOP SIDE IC-F7520 BOTTOM SIDE IC-F7520 LEFT SIDE IC-F7520 RIGHT SIDE REMOTE HEAD FRONT SIDE REMOTE HEAD REAR SIDE REMOTE HEAD TOP SIDE REMOTE HEAD BOTTOM SIDE REMOTE HEAD LEFT SIDE REMOTE HEAD RIGHT SIDE

IC-F7520 Serial Plate

Serial seal location The position of the serial seal is the upper right corner of the bottom side. IC-F7520 BOTTOM SIDE

IC-F7520 MAIN-D UNIT A SIDE IC-F7520 MAIN-D UNIT B SIDE IC-F7520 CONNECT-D UNIT A SIDE IC-F7520 CONNECT-D UNIT B SIDE IC-F7520 RELAY-D UNIT A SIDE IC-F7520 RELAY-D UNIT B SIDE IC-F7520 Board(UT-136) on RELAY-D UNIT A SIDE IC-F7520 Board(UT-136) on RELAY-D UNIT B SIDE IC-F7520 FRONT-A UNIT A SIDE IC-F7520 FRONT-A UNIT B SIDE IC-F7520 JACK-A UNIT A SIDE IC-F7520 JACK-A UNIT B SIDE IC-F7520 VR-A UNIT A SIDE IC-F7520 VR-A UNIT B SIDE IC-F7520 AES/DES UNIT(UT-134) SIDE A IC-F7520 AES/DES UNIT(UT-134) SIDE B IC-F7520 AES/DES UNIT(UT-125 FIPS) SIDE A IC-F7520 AES/DES UNIT(UT-125 FIPS) SIDE B

MPE Report FCC ID: AFJ384612 ICOM-600_MPE 1.1. RF EXPOSURE REQUIREMENTS [§§ 1.1310 & 2.1091] 1.1.1. Limits § 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 6141.63*(100)6 3.0-30 1842/f4.89/f*(900/f 2 )6 30-300 61.40.1631.06 300-1500 f/3006 1500-100,000 56 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 6141.63*(100)30 1.34-30 824/f2.19/f*(180/f 2 )30 30-300 27.50.0730.230 300-1500 f/150030 1500-100,000 1.030 f = frequency in MHz * = Plane-wave equivalent power density Note 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. Note 2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. 1.1.2. Method of Measurements Calculation Method of RF Safety Distance : 22 44r EIRP r PG S      MPE Report FCC ID: AFJ384612 ICOM-600_MPE Where, P: power input to the antenna in mW EIRP: Equivalent (effective) isotropic radiated power. S: power density mW/cm 2 G: numeric gain of antenna relative to isotropic radiator r: distance to centre of radiation in cm S EIRP S PG r     44 FCC radio frequency exposure limits may be exceeded at distances closer than r cm from the antenna of this device. 1.1.3. Evaluation of RF Exposure Compliance Requirements This mobile radio also contains a Bluetooth Module which may transmit simultaneously with Tx output power of 0.00204 Watts which is very low and category excluded for mobile application where minimum 20cm user separation distance from the radio is always maintained. Maximum RF Power conducted, P conducted [W]: 49.32 Maximum Antenna Gain, G[dBi]: 0 Maximum EIRP, P EIRP [W]: 49.32 User-based time-average for PTT 50% MPE Limit for Occupational/Controlled Exposure, S controlled [mW/cm 2 ]: 1.5 MPE Limit for General Population/Uncontrolled Exposure, S uncontrolled [mW/cm 2 ] 0.3 Min Calculated RF Safety Distance for Occupational/Controlled Exposure, r safetycontrolled [cm]: 37 Min Calculated RF Safety Distance for General Population/Uncontrolled Exposure, r safety_uncontrolled [cm] 81 MPE Report FCC ID: AFJ384612 ICOM-600_MPE

This Te s Tri M. Lu Vice Pre UltraTec Date: D e Report P Issued D  The res  This re  This tes 0 st report is Iss uu, BASc, esident of Eng ch Group of L ecember 14, Prepared by: Date: Decemb sults in this Test Re eport must not be us st report shall not b Web 0685 TE Federal 47 CFR Ultr sued under th gineering Labs 2022 Santhosh Fe ber 14, 2022 eport apply only to sed by the client to be reproduced, exc 30 bsite: www.ultratec APEC LCA0001 UHF P2 Model FCC ID A ICOM 1-1-32, Kam Osaka, J Tested in l Communic R, Parts 2, 22 raTech's File he Authority o rnandez the sample(s) teste o claim product end cept in full, without Ult 00 Bristol Circle, O Tel.: (905) 829- h-labs.com, Email: 1309 C 25 Transce No.: IC-F7 D: AFJ3846 Applicant: M Incorporat miminami, H Japan, 547- n Accordance cations Com 2, 74, 80 an e No.: 22ICOM of Tested b Test Da ed, and the sample dorsement by any a a written approval traTech Oakville, Ontario, Ca -1570 Fax.: (905) vic@ultratech-labs A 0001/2049 eiver 7520 612 ted Hirano-ku -0003 e With mmission (F d 90 (Subpa M600_FCC90 by: Nimisha D tes: Novembe e tested is randomly agency of the US G from UltraTech. h anada, L6H 6G4 ) 829-8050 s.com, Email: tri@u AT-1945 FCC) art I) 0 Desai er 22-25, 202 y selected. Government. ultratech-labs.com SL2-IN- 1119R 22 Korea KC RRA -E- R CA000 1 CC- 1 FCC Parts 2, 22, 74, 80 and 90 Subpart I, Non-Broadcast Radio Transceivers Contents i UHF P25 Transceiver, Model: IC-F7520 FCC ID: AFJ384612 ULTRATECH GROUP OF LABS File #: 22ICOM600_FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 December 14, 2022 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE ............................................................................................................................................................................ 1 1.2. RELATED SUBMITTAL(S)/GRANT(S) ...................................................................................................................... 1 1.3. NORMATIVE REFERENCES ....................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT .................................................................................................................. 2 2.1. CLIENT INFORMATION ............................................................................................................................................. 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ................................................................................................. 2 2.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................... 3 2.4. LIST OF EUT’S PORTS ................................................................................................................................................. 4 2.5. ANCILLARY EQUIPMENT ......................................................................................................................................... 4 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ................................... 5 3.1. CLIMATE TEST CONDITIONS ................................................................................................................................... 5 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS .................................................. 5 EXHIBIT 4. SUMMARY OF TEST RESULTS .................................................................................................................. 6 4.1. LOCATION OF TESTS ................................................................................................................................................. 6 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ............................................................................ 6 4.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ............................................ 6 EXHIBIT 5. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .................................. 7 5.1. TEST PROCEDURES .................................................................................................................................................... 7 5.2. MEASUREMENT UNCERTAINTIES .......................................................................................................................... 7 5.3. MEASUREMENT EQUIPMENT USED ....................................................................................................................... 7 5.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ............................................ 7 5.5. RF POWER OUTPUT [§§ 2.1046, 22.565, 74.461, 80.215 & 90.205] ........................................................................... 8 5.6. AUDIO FREQUENCY RESPONSE [§ 2.1047(A), 80.213(E) & 90.242(B)(8)] .............................................................. 9 5.7. MODULATION LIMITING [§§ 2.1047 (B), 74.463, 80.213 & 90.210] ....................................................................... 14 5.8. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 74.462, 80.211(F), 90.209 & 90.210] ........................ 19 5.9. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§ 2.1051, 2.1057, 22.359, 80.211(F)(3) & 90.210] ................................................................................................................................................ 57 5.10. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§§ …

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7520 FCC ID: AFJ384612 ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7520 FCC ID: AFJ384612 ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7520 FCC ID: AFJ384612