AFJ399110UHF P25 Transceiver

RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. RWARNING! NEVER operate the transceiver during a lightning storm. It may result in an electric shock, cause a fire or damage the transceiver. Always disconnect the power souce and antenna before a storm. RWARNING! NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This could damage the transceiver. RWARNING! NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. RWARNING! NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. CAUTION: Confirm that all connectors and jacks are dry and clean before attachment. Exposing them to dust or water will result in serious damage to the transceiver. CAUTION: The transceiver will become hot when operating continuously for long periods. DO NOT place or leave the transceiver in areas with temperatures below –30°C (–22°F) or above 60°C (140°F), or in areas subject to direct sunlight, such as the dashboard. DO NOT place or leave the transceiver in direct sunlight or in areas outside of the specified temperature range: –30°C (–22°F) ~ 60°C (140°F) DO NOT operate the transceiver without running the vehicle’s engine. The vehicle’s battery will quickly run out when the transceiver transmits while the vehicle’s engine is OFF. DO NOT place or leave the transceiver in excessively dusty environments. DO NOT place the transceiver against walls. Otherwise heat dissipation will be obstructed. DO NOT use harsh solvents such as Benzine or alcohol when cleaning, as they damage the transceiver’s surfaces. DO NOT block the air vent when installing the transceiver. This transceiver has an air vent on the bottom panel of the transceiver to meet the IP55 requirements. Use the specified microphone only. Other microphones have different pin assignments and may damage the radio. Place the radio in a secure place to avoid inadvertent use by unauthorized persons. Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. • For compliance with FCC and IC RF Exposure Requirements, the transmitter antenna installation shall comply with the following three conditions: 1. The transmitter antenna gain shall not exceed 0 dBi. 2. IC-F7510: The antenna is required to be located outside of a vehicle and kept at a distance of 57 centimeters (23 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 57 centimeters (23 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 57 centimeters (23 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 2. IC-F7520: The antenna is required to be located outside of a vehicle and kept at a distance of 42 centimeters (17 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 42 centimeters (17 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 42 centimeters (17 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 2. IC-F7540: The antenna is required to be located outside of a vehicle and kept at a distance of 31 centimeters (12 inches) or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the center line along the vehicle in order to achieve 31 centimeters (12 inches) separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 31 centimeters (12 inches) away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 3. IC-F7510: Transmit only when people outside the vehicle are at least the recommended minimum distance of 136 centimeters (54 inches) away from the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed externally-mounted antenna to satisfy the RF exposure requirements in the applicable RF exposure compliance standards. 3. IC-F7520: Transmit only when people outside the vehicle are at least the recommended minimum distance of 119 centimeters (47 inches) away from the properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed externally-mounted antenna to satisfy the RF exposure requirements in the applicable RF exposure compliance standards. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A7383D-1EX-3 Printed in Japan © 2017–2018 Icom Inc. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: •Force majeure, including, but not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. •The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. FCC INFORMATION This equipment has bee…

Text truncated - open the document above for the full version.

For USA Only Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: Trade Name : ICOM Model Name: : IC-F7540 Responsible party: Company name : Icom America Inc. Address : 12421 Willows Road NE Kirkland, WA 98034 U.S. Contact Information: 800-USA-ICOM (800-872-4266) Monday - Friday 7AM to 5PM PST FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

Ultr Gr FCC 4 SL2 Kor 30 O C Tel. Fax Website: Email: raTech roup of Labs C TCB & IC CB 0685 91038 1309 46390-2049 AT-1945 2-IN-E-1119R rea KCC-RRL CA2049 000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 : (905) 829-1570 .: (905) 829-8050 www.ultratech-labs.c o [email protected] Se p Ultr 300 Oak L6H Su b App Pro Mo FC C De a As for fili n If y o Yo u Sa Aut h om om ptember 8, 20 ratech Engin 00 Bristol Circ kville, Ontario H 6G4 bject: plicant: oduct: del: C ID: ar Sir/Madam appointed ag FCC certifica ng site. ou have any q urs truly, anthosh Fer thorized Agen 023 neering Labs cle o Equipment C Broadcast R 775 MHz, 79 12.5 kHz Ch a ICOM Incorp UHF P25 Tra IC-F7540 AFJ399110 m: gent for ICOM ation of the ab queries, pleas ernandez nt s, Inc. Certification Radio Transc 9-805 MHz, 8 annel Spacin porated ansceiver M Incorporate bove product. se do not hes under FCC 4 ceivers Opera 806-824 MHz ng) ed, we would Please revi e sitate to conta 47 CFR, Part ating in the F z, 851-869 MH like to submit ew all files up act us. ts 2, 22 and 9 Frequency B Hz (25 kHz, 2 t the applicati loaded to yo u 90 - Non- Band 769- 0 kHz and on to you ur electronic

IC-F7540 FRONT SIDE IC-F7540 REAR SIDE IC-F7540 LEFT SIDE IC-F7540 RIGHT SIDE IC-F7540 TOP SIDE IC-F7540 BOTTOM SIDE Remote Head Connection (1) Remote Head Connection (2) IC-F7540 FRONT SIDE IC-F7540 Rear SIDE IC-F7540 TOP SIDE IC-F7540 BOTTOM SIDE IC-F7540 LEFT SIDE IC-F7540 RIGHT SIDE REMOTE HEAD FRONT SIDE REMOTE HEAD REAR SIDE REMOTE HEAD TOP SIDE REMOTE HEAD BOTTOM SIDE REMOTE HEAD LEFT SIDE REMOTE HEAD RIGHT SIDE

IC-F7540 Serial Plate Serial seal location The position of the serial seal is the upper right corner of the bottom side. IC-F7540 BOTTOM SIDE

IC-F7540 MAIN-A UNIT A SIDE IC-F7540 MAIN-A UNIT B SIDE IC-F7540 CONNECT-A UNIT A SIDE IC-F7540 CONNECT-A UNIT B SIDE IC-F7540 RELAY-A UNIT A SIDE IC-F7540 RELAY-A UNIT B SIDE IC-F7540 Board(UT-136) on RELAY-A UNIT A SIDE IC-F7540 Board(UT-136) on RELAY-A UNIT B SIDE IC-F7540 FRONT-A UNIT A SIDE IC-F7540 FRONT-A UNIT B SIDE IC-F7540 JACK-A UNIT A SIDE IC-F7540 JACK-A UNIT B SIDE IC-F7540 VR-A UNIT A SIDE IC-F7540 VR-A UNIT B SIDE IC-F7540 AES/DES UNIT(UT-134) SIDE A IC-F7540 AES/DES UNIT(UT-134) SIDE B IC-F7540 AES/DES UNIT(UT-125 FIPS) SIDE A IC-F7540 AES/DES UNIT(UT-125 FIPS) SIDE B

MPE report ICOM615_MPE FCC ID: AFJ399110 1.1. RF EXPOSURE REQUIREMENTS [§§ 1.1310 & 2.1091][RSS-102] 1.1.1. Limits § 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 6141.63*(100)6 3.0-30 1842/f4.89/f*(900/f 2 )6 30-300 61.40.1631.06 300-1500 f/3006 1500-100,000 56 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 6141.63*(100)30 1.34-30 824/f2.19/f*(180/f 2 )30 30-300 27.50.0730.230 300-1500 f/150030 1500-100,000 1.030 f = frequency in MHz * = Plane-wave equivalent power density RSS-102.:The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in RSS-102. Table 4: RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m 2 ) Reference Period (minutes) 300-6000 3.142 ƒ 0.3417 0.008335 ƒ 0.3417 0.02619ƒ 0.6834 6 Note: ƒ is frequency in MHz. Table 6: RF Field Strength Limits for Controlled Use Devices (Controlled Environment) Note 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure Frequency Range (MHz) Electric Field (V/m rms) Magnetic Field (A/m rms) Power Density (W/m 2 ) Reference Period (minutes) 100-6000 15.60 ƒ 0.25 0.04138 ƒ 0.25 0.6455ƒ 0.5 6 Note: ƒ is frequency in MHz. MPE report ICOM615_MPE FCC ID: AFJ399110 and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. Note 2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. 1.1.2. Method of Measurements Calculation Method of RF Safety Distance : 22 44r EIRP r PG S      Where, P: power input to the antenna in mW EIRP: Equivalent (effective) isotropic radiated power. S: power density mW/cm 2 G: numeric gain of antenna relative to isotropic radiator r: distance to centre of radiation in cm S EIRP S PG r     44 FCC radio frequency exposure limits may be exceeded at distances closer than r cm from the antenna of this device. MPE report ICOM615_MPE FCC ID: AFJ399110 1.1.3. Evaluation of RF Exposure Compliance Requirements . This mobile radio also contains a Bluetooth Module which may transmit simultaneously with Tx output power of 0.00204 Watts which is very low and category excluded for mobile application where minimum 20cm user separation distance from the radio is always maintained 1.1.3.1. FCC Evaluation Maximum RF Power conducted, P conducted [W]: 35.0 Maximum Antenna Gain, G[dBi]: 0 Maximum EIRP, P EIRP [W]: 35.0 User-based time-average for PTT 50% MPE Limit for Occupational/Controlled Exposure, S controlled [mW/cm 2 ]: 2.56 MPE Limit for General Population/Uncontrolled Exposure, S uncontrolled [mW/cm 2 ] 0.512 Min Calculated RF Safety Distance for Occupational/Controlled Exposure, r safetycontrolled [cm]: 24 Min Calculated RF Safety Distance for General Population/Uncontrolled Exposure, r safety_uncontrolled [cm] 53 1.1.3.2. ISED Evaluation Maximum RF Power conducted, P conducted [W]: 35 Maximum Antenna Gain, G[dBi]: 0 Maximum EIRP, P EIRP [W]: 35 User-based time-average for PTT 50 % MPE Environment Power Density limit , S (mW/m 2 ) Minimum Distance (Cm) Distance In user’s manual (Cm) Power Density at user’s manual distance, S (mW/m 2 ) Power Density at user’s manual distance, S (W/m 2 ) Occupational/Controlled Exposure 1.79 28 31 (0.31m)1.44 14.4 General Population/Uncontrolled Exposure 0.24 77 82 (0.82m) 0.21 2.1 MPE report ICOM615_MPE FCC ID: AFJ399110

This Te s Tri M. Lu Vice Pre UltraTec Date: S e Report P Issued D  The res  This re  This tes st report is Iss uu, BASc, esident of Eng ch Group of L eptember 1, 2 Prepared by: Date: Septem sults in this Test Re eport must not be us st report shall not b Web Federal 47 CF Ultr sued under th gineering Labs 2023 Santhosh Fe mber 1, 2023 eport apply only to sed by the client to be reproduced, exc 30 bsite: www.ultratech APEC TEL CA0001 UHF P2 Model FCC ID A ICOM 1-1-32, Kam Osaka, J Tested in l Communic FR, Parts 2, raTech's File he Authority o rnandez the sample(s) teste o claim product end cept in full, without U 00 Bristol Circle, O Tel.: (905) 829-15 h-labs.com, Email: 1309 46 25 Transce No.: IC-F7 D: AFJ399 Applicant: M Incorporat miminami, H Japan, 547- n Accordance cations Com 22 and 90 ( e No.: 23ICOM of Tested b Test Da ed, and the sample dorsement by any a a written approval UltraTec Oakville, Ontario, Ca 570 Fax.: (90 vic@ultratech-labs  6390-2049 eiver 7540 110 ted Hirano-ku -0003 e With mmission (F (Subpart R, M615_FCC90 by: Nimisha D tes: August 9 e tested is randomly agency of the US G from UltraTech. ch anada, L6H 6G4 05) 829-8050 s.com, Email: tri@u AT-1945 FCC) S) 0 Desai 9-28, 2023 y selected. Government. ultratech-labs.com SL2-IN-E 1119R Korea KCC-RR A E- CA0001 A FCC Parts 2, 22 and 90 Non-Broadcast Radio Transceivers Contents i UHF P25 Transceiver, Model: IC-F7540 FCC ID: AFJ399110 ULTRATECH GROUP OF LABS File #: 23ICOM615_FCC90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 September 1, 2023 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ............................................................................................................................................ 1 1.1. SCOPE ............................................................................................................................................................................ 1 1.2. REVISION HISTORY .................................................................................................................................................... 1 1.3. RELATED SUBMITTAL(S)/GRANT(S) ...................................................................................................................... 1 1.4. NORMATIVE REFERENCES ....................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT .................................................................................................................. 2 2.1. CLIENT INFORMATION ............................................................................................................................................. 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION ................................................................................................. 2 2.3. EUT’S TECHNICAL SPECIFICATIONS ..................................................................................................................... 3 2.4. LIST OF EUT’S PORTS ................................................................................................................................................. 4 2.5. ANCILLARY EQUIPMENT ......................................................................................................................................... 4 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ................................... 5 3.1. CLIMATE TEST CONDITIONS ................................................................................................................................... 5 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS .................................................. 5 EXHIBIT 4. SUMMARY OF TEST RESULTS .................................................................................................................. 6 4.1. LOCATION OF TESTS ................................................................................................................................................. 6 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ............................................................................ 6 4.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ............................................ 7 4.3.1. DEVIATION OF STANDARD TEST PROCEDURES ............................................................................................ 7 EXHIBIT 5. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .................................. 8 5.1. TEST PROCEDURES .................................................................................................................................................... 8 5.2. MEASUREMENT UNCERTAINTIES .......................................................................................................................... 8 5.3. MEASUREMENT EQUIPMENT USED ....................................................................................................................... 8 5.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ............................................ 8 5.5. RF POWER OUTPUT [§§ 2.1046, 90.205, 90.541& 90.543] ......................................................................................... 9 5.5.1. Limits ...................................................................................................................................................................... 9 5.5.2. Method of Measurements ........................................................................................................................................ 9 5.5.3. Test Data ........................................................................…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7540 FCC ID: AFJ399110; IC: 202D-399110 Radiated Emissions ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7540 FCC ID: AFJ399110; IC: 202D-399110 ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7540 FCC ID: AFJ399110; IC: 202D-399110 ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7540 FCC ID: AFJ399110; IC: 202D-399110 Conducted Emissions‐ Powerline ANNEX 1 - TEST SETUP PHOTOGRAPHS ICOM Incorporated IC‐F7540 FCC ID: AFJ399110; IC: 202D-399110