AFJ418001Two Way Radio

Picture Front view Rear view Picture Top view Bottom view Picture Right view Left view Picture Serial view

Serial Plate IP740D #11 Picture Serial view

Electronic Label Refer to the "Certification" screen for certifications acquired with the transceiver. 1. Turn OFF the transceiver, if it is turned ON. 2. While holding down [FUNC], rotate [VOL] to turn ON the transceiver. The Set mode is displayed. 3. Rotate Rotary Selector or push [▲] or [▼] to Select “Certification” and then push [FUNC] to display certifications. Cellular CERT Bluetooth CERT Bluetooth CERT Push [FUNC] Push [FUNC] Push [FUNC] Push [ጴጵጶጷጸጹ] Push [ጴጵጶጷጸጹ] Push [ጴጵጶጷጸጹ] Cellular CERT

Picture MAIN Board side-A view Picture MAIN Board side-B view Picture Front Board side-A view Front Board side-B view

© 2020 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION ICOM, Inc. Dates of Test: December 2-11, 2020 1-1-32 Kamiminami Hirano-ku Test Report Number: SAR.20201210 Osaka 547-0003 Revision B Japan This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for controlled environment/occupational and uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and IEC 62209-2:2010 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Testing Cert. # 2387.01 FCC ID: AFJ418001 IC Certificate: 202D-418001 Model(s): IP740D HVIN: 418001-01 Test Sample: Engineering Unit Same as Production Serial No.: Eng 1 Equipment Type: Push-To-Talk Handheld Radio for Occupational Population Use Classification: Portable Transmitter Next to Face and Body TX Frequency Range: 400 – 520 MHz, 699 – 716 MHz; 824 – 849 MHz; 1710 – 1755 MHz; 1850 – 1910 MHz; 2402 – 2480 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 450 MHz (FM) – 36.99 dBm, 750 MHz (LTE) – 25.7 dBm, 835 MHz (WCDMA) – 25.0 dBm, 1750 MHz (LTE) – 25.7 dBm, 1900 MHz (WCDMA) – 25.0 dBm, 1900 MHz (LTE) -24.0 dBm, 2450 MHz (BT) – 4.0 dBm Conducted Signal Modulation: FM, QPSK, 16QAM, DSSS, GFSK Body Worn: MB-133, MB-136, MB-96F, MB-96FL, MB-96N, MB57L, LC-195 Audio Accessories: HM-163MC, HM-184, HM-184H, HM-222, HM-222H, HM-236, HM-238MC, HM-245T, SP16-BW, SP-26, SP-27, SP-28, SP-29, SP- 40, HS-94, HS-95, HS-97, VS-3, VS-4MC, VS-5MC, AD-135 Antenna Type: FA-SC01U, FA-SC02U, FA-SC03U, FA-SC25U, FA-SC26US, FA-SC57U, FA-SC61UC, FA-SC72U, FA-SC73US and Internal Antenna For Cellular/BT Battery: BP-302, BP-303, BP-305 Application Type: Certification FCC Rule Parts: Part 2, 15, 22, 24, 27, 80, 90 KDB Test Methodology: KDB 447498 D01 v06, KDB 643646 D01 v01r03, KDB 941225 D05 v02r05, KDB 865664 D01 v01r04, KDB 865664 D02 v01r02 Industry Canada: RSS-102 Issue 5, Safety Code 6 Max. Stand Alone SAR Value: 2.68 W/kg for Face; 4.55 for Body Reported Max. Simultaneous SAR Value: 0.39 W/kg Reported; 0.41 For Ratio Limit Separation Distance: 25 mm for Face; 0 mm for Body Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 2 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ........................................................................................................................ 4 SAR Definition [5] ................................................................................................................... 5 2. SAR Measurement Setup ................................................................................................... 6 Robotic System ...................................................................................................................... 6 System Hardware ................................................................................................................... 6 System Electronics ................................................................................................................. 7 Probe Measurement System .................................................................................................. 7 3. Probe and Dipole Calibration .............................................................................................15 4. Phantom & Simulating Tissue Specifications .....................................................................16 Head & Body Simulating Mixture Characterization ................................................................16 5. ANSI/IEEE C95.1 – 1999 RF Exposure Limits [2] ..............................................................17 Uncontrolled Environment .....................................................................................................17 Controlled Environment .........................................................................................................17 6. Measurement Uncertainty .................................................................................................18 7. System Validation..............................................................................................................19 Tissue Verification .................................................................................................................19 Test System Verification ........................................................................................................19 8. LTE Document Checklist ...................................................................................................20 9. SAR Test Data Summary ..................................................................................................23 Procedures Used To Establish Test Signal ...........................................................................23 Device Test Condition ...........................................................................................................23 10. 3G Measurement Procedures ........................................................................................37 10.1 Procedures Used to Establish RF…

Text truncated - open the document above for the full version.

Report No.: FCC_RF_SL20081801-ICOM-009_REV 4.0 1 of 60 Report Format Version 6.1.1 FCC Part 90 (Subpart I) RF Test Report Report No.: FCC_RF_SL20081801-ICOM-009_REV 4.0 FCC ID: AFJ418001 Test Model: IP740D Received Date: 10/11/2020 Sample was received in good condition Test Date: 10/11/2020 -11/23/2020 and 05/15/2021 to 05/18/2021 Original Report : Rev1 Issue date: Current rev4: 11/23/2020 05/18/2021 01/08/2023 Applicant: Icom Inc. Address: 1-1-32 Kamiminami Hirano-ku, Osaka Japan 547-0003, Japan Manufacturer: Icom Inc. Address: 1-1-32 Kamiminami Hirano-ku, Osaka Japan 547-0003, Japan Issued By: Bureau Veritas Consumer Products Services, Inc. Lab Address: 775 Montague Expressway, Milpitas, CA 95035 Test Location (1): 775 Montague Expressway, Milpitas, CA 95035 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: FCC_RF_SL20081801-ICOM-009_REV 4.0 2 of 60 Report Format Version 6.1.1 Table of Contents RELEASE CONTROL RECORD ........................................................................................... 3 1 CERTIFICATE OF CONFORMITY ........................................................................... 4 2 SUMMARY OF TEST RESULTS.............................................................................. 5 3 MEASUREMENT UNCERTAINTY ........................................................................... 7 4 MODIFICATION RECORD ...................................................................................... 7 5 GENERAL INFORMATION ...................................................................................... 8 5.1 GENERAL DESCRIPTION OF EUT ..................................................................... 8 5.2 POWER SETTING ............................................................................................. 11 5.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ..................................... 12 5.4 DESCRIPTION OF SUPPORT UNITS ............................................................... 13 5.5 CONFIGURATION OF SYSTEM UNDER TEST................................................. 14 5.6 FCC §1.1310 & §2.1093 - RF EXPOSURE ........................................................ 15 5.7 RF OUTPUT POWER ........................................................................................ 16 5.8 MODULATION CHARACTERISTIC ................................................................... 19 5.9 OCCUPIED BANDWIDTH & EMISSION MASK ................................................. 23 5.10 SPURIOUS EMISSIONS AT ANTENNA TERMINALS ........................................ 38 5.11 FCC §2.1053; & §90.210 - RADIATED SPURIOUS EMISSIONS ....................... 46 5.12 FREQUENCY STABILITY .................................................................................. 51 5.13 FCC §90.214 - TRANSIENT FREQUENCY BEHAVIOR ..................................... 54 6. INFORMATION ON THE TESTING LABORATORIES ............................................60 Report No.: FCC_RF_SL20081801-ICOM-009_REV 4.0 3 of 60 Report Format Version 6.1.1 Release Control Record ISSUE NO. REASON FOR CHANGE DATE ISSUED FCC_RF_SL20081801-ICOM-009 Orignal Release 11/23/ 2020 FCC_RF_SL20081801-ICOM-009_REV 1.0 Revise the incorrect test result 05/17/ 2021 FCC_RF_SL20081801-ICOM-009_REV 2.0 Revised to remove RSS references. 04/10/2022 FCC_RF_SL20081801-ICOM-009_REV 3.0 Revised to remove Part 22, 24 and to make part 90 Report Corrected Modulation Characteristic and Frequcency stability errors in the report 12/30/2022 FCC_RF_SL20081801-ICOM-009_REV 4.0 Removed Modulation Limiting test and updated test equipment list 01/08/2023 Report No.: FCC_RF_SL20081801-ICOM-009_REV 4.0 4 of 60 Report Format Version 6.1.1 1 Certificate of Conformity Product: Two Way Radio Brand: Icom Test Model: IP740D Sample Status: Engineering sample Applicant: Icom Inc. Test Date: 10/11/2020 -11/23/2020 and 05/15/2021 to 05/18/2021 Standards: FCC Part 90 (Subpart I) The above equipment has been tested by Bureau Veritas Consumer Products Services, Inc., Milpitas Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: 05/18/2021 Gary Chou / Compliance Engineer Approved by : , Date: 05/18/2021 Deon Dai / Engineer Reviewer 1.1.1.1.1.1 Revision 2 Approved by: ______, Date: 04/10/2022 Suresh Kondapalli Technical Director Revision 4 Approved by: ______, Date: 01/08/2023 Suresh Kondapalli Technical Director Report No.: FCC_RF_SL…

Text truncated - open the document above for the full version.

Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 97 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Appendix C – SAR Test Setup Photos Test Position Face 25 mm Gap Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 98 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Test Position Body 0 mm Gap Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 99 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Front of Device Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 100 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Back of Device Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 101 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Antennas Report Number: SAR.20201210 © 2020 RF Exposure Lab, LLC Page 102 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Audio and Body Worn Accessory

Radiated Emission Test below 1GHz Front View Radiated Emission Test below 1GHz Rear View Radiated Emission Test above 1GHz Front View Radiated Emission Test above 1GHz Rear View