AFJ446700IP-M60 Marine Radio

PRECAUTIONS RDANGER! NEVER operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. This could cause an explosion and death. RWARNING! NEVER use or charge Icom battery packs with non-Icom transceivers or non-Icom chargers. Only Icom battery packs are tested and approved for use with Icom transceivers or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fi re, or cause the battery to burst. RWARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. If the antenna is close to you, transmit with low power. RWARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. The continuous high volume operation may cause a ringing in your ears. If you experience the ringing, reduce the volume level or discontinue use. RWARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention— anything less could result in an accident. CAUTION: DO NOT short the terminals of the battery pack. Shorting may occur if the terminals touch metal objects such as a key, so be careful when placing the battery packs (or the transceiver) in bags, and so on. Carry them so that shorting cannot occur with metal objects. Shorting may damage not only the battery pack, but also the transceiver. CAUTION: DO NOT use harsh solvents such as Benzine or alcohol when cleaning. This could damage the equipment surfaces. If the surface becomes dusty or dirty, wipe it clean with a soft, dry cloth. CAUTION: DO NOT place or leave the transceiver in excessively dusty environments. This could damage the transceiver. NEVER place the transceiver in an insecure place to avoid inadvertent use by unauthorized persons. DO NOT place or leave the transceiver in areas with temperatures below –20°C (–4°F) or above +60°C (+140°F), or in areas subject to direct sunlight, such as the dashboard. BE CAREFUL! The transceiver meets IP67* requirements for dust tight and waterproof protection. However, once the transceiver has been dropped and cracked, or the waterproof seal is cracked or damaged, dust tight and waterproof protection cannot be guaranteed. * Only when the battery pack, antenna, and connector cover or the optional speaker microphone is attached. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: • Force majeure, including, but not limited to, fi res, earthquakes, storms, fl oods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. • The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifi cations to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. RECOMMENDATION CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL OF FRESH WATER after exposure to saltwater, and dry it before operating. Otherwise, the transceiver’s keys and switches may become unusable, due to salt crystallization, and/or the charging terminals of the battery pack may corrode. NOTE: If the transceiver’s waterproof protection appears defective, carefully clean the transceiver with a soft, damp (fresh water) cloth, then dry it before operating. The transceiver may lose its waterproof protection if the case, jack cover, or battery cover is cracked or broken, or the transceiver has been dropped. Contact your Icom distributor or your dealer for advice. Icom and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. AquaQuake is a trademark of Icom Incorporated. The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Icom Inc. is under license. All other products or brands are registered trademarks or trademarks of their respective holders. EXPLICIT DEFINITIONS WORDDEFINITION RDANGER!Personal death, serious injury or an explosion may occur. RWARNING!Personal injury, fi re hazard or electric shock may occur. CAUTIONEquipment damage may occur. NOTEIf disregarded, inconvenience only. No risk of personal injury, fi re or electric shock. DBattery caution Misuse of Li-ion batteries may result in the following hazards: smoke, fi re, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. RDANGER! NEVER place battery packs near a fi re. Fire or heat may cause them to rupture or explode. Dispose of used battery packs in accordance with local regulations. RDANGER! NEVER let fl uid from inside the battery get in your eyes. This can cause blindness. Rinse your eyes with clean water, without rubbing them, and immediately get medical treatment from an eye doctor. RDANGER! NEVER solder the battery terminals, or NEVER modify the battery pack. This may cause heat generation, and the battery may burst, …

Text truncated - open the document above for the full version.

For USA Only Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier: Trade Name : ICOM Model Name: : IP-M60 Responsible party: Company name : Icom America Inc. Address : 12421 Willows Road NE Kirkland, WA 98034 U.S. Contact Information: 800-USA-ICOM (800-872-4266) Monday - Friday 7AM to 5PM PST FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

Picture Front view Rear view Picture Top view Bottom view Picture Right view Left view Picture Serial view

Serial Seal IP-M60 Serial Seal Location Serial Seal

Electronic Label Refer to the "Certification" screen for certifications acquired with the transceiver. 1. Turn OFF the transceiver, if it is turned ON. 2. While holding down [FUNC], rotate [VOL] to turn ON the transceiver. The Set mode is displayed. 3. Rotate Rotary Selector or push [▲] or [▼] to Select “Certification” and then push [FUNC] to display certifications. Push[FUNC] Push[] Push[FUNC] Push[]Push[FUNC] Push[FUNC] Push[] Push[]

Picture FRONT Board side-A view Picture FRONT Board side-B view Picture MAIN Board side-A view Picture MAIN Board side-B view Picture Bluetooth module（by Front Board side-B） FCC ID : AFJ387300 IC : 202D-387300 Model : HRM1086 Picture LTE module（by MAIN Board side-A） FCC ID : UDV-201606 IC : 23761-8PYA003 Model : SIM7500A

© 2024 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION ICOM, Inc. Dates of Test: January 5-10, 2024 1-1-32 Kamiminami Hirano-ku Test Report Number: SAR.20240103 Osaka 547-0003 Revision A Japan Lab Designation Number: US1195 This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI C95.1 – 1999 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz, ANSI C95.3 – 2002 Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields, IEEE Std.1528 – 2013 Recommended Practice and had been tested in accordance with the measurement procedures specified in KDB 447498 and KDB 248227 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application is subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Testing Cert. # 2387.01 FCC ID: AFJ446700 Model(s): IP-M60 Test Sample: Engineering Unit Same as Production Serial No.: Eng 1 Equipment Type: Push-To-Talk Handheld Radio for General Population Use Classification: Portable Transmitter Next to Face and Body TX Frequency Range: 156 – 158 MHz, 699 – 716 MHz; 824 – 849 MHz; 1710 – 1755 MHz; 1850 – 1910 MHz; 2402 – 2480 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 150 MHz (FM) – 36.99 dBm, 750 MHz (LTE) – 25.7 dBm, 835 MHz (WCDMA) – 25.0 dBm, 1750 MHz (LTE) – 25.7 dBm, 1900 MHz (WCDMA) – 25.0 dBm, 1900 MHz (LTE) -24.0 dBm, 2450 MHz (BT) – 11.0 dBm Conducted Signal Modulation: FM, QPSK, 16QAM, DSSS, GFSK Body Worn: MB-133, MB-136, MB-96F, MB-96FL, MB57L, LC-195 Audio Accessories: HM-184H, HM-222H, HM-238C, EH-15B, SP-26, SP-27, SP-28, SP-29, SP-40, HS-94, HS-95, HS-97 Antenna Type: FA-S59V and Internal Antenna For Cellular/BT Battery: BP-303 Application Type: Certification FCC Rule Parts: Part 2, 15, 22, 24, 27, 80, 90 KDB Test Methodology: KDB 447498 D01 v06, KDB 643646 D01 v01r03, KDB 941225 D05 v02r05, KDB865664 D01 v01r04, KDB 865664 D02 v01r02 Max. Stand Alone SAR Value: 0.67 W/kg for Face Reported; 0.54 W/kg for Body Reported Max. Simultaneous SAR Value: 0.49 W/kg for Face Reported; 0.36 W/kg for Body Reported Separation Distance: 25 mm for Face; 0 mm for Body Report Number: SAR.20240103 © 2024 RF Exposure Lab, LLC Page 2 of 129 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ......................................................................................................................................................... 4 SAR Definition [5] .................................................................................................................................................... 5 2. SAR Measurement Setup .................................................................................................................................... 6 Robotic System ....................................................................................................................................................... 6 System Hardware .................................................................................................................................................... 6 System Electronics .................................................................................................................................................. 6 Probe Measurement System ................................................................................................................................... 7 3. Probe and Dipole Calibration ............................................................................................................................. 14 4. Phantom & Simulating Tissue Specifications ..................................................................................................... 15 Head Simulating Mixture Characterization ............................................................................................................. 15 5. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] .............................................................................................. 16 Uncontrolled Environment ..................................................................................................................................... 16 Controlled Environment ......................................................................................................................................... 16 6. Measurement Uncertainty.................................................................................................................................. 17 7. System Validation .............................................................................................................................................. 18 Tissue Verification ................................................................................................................................................. 18 Test System Verification ........................................................................................................................................ 18 8. LTE Document Checklist ................................................…

Text truncated - open the document above for the full version.

P23b0001_FCC_ Part 80_Rev 1.0 Page 1 of 23 Test Report Prepared for: Icom Incorporated Mod el: IP-M60 De scription: Marine Radio Ser ial Number: 000000000023 FCC I D: AFJ446700 ISED ID: 202D-446700 To FC C Part 80 RSS- 182 Issue 6 (June 2021) Da te of Issue: December 20, 2023 On the behalf of the applicant: Icom Incorporated 1-1-32 Kamiminami Hirano-ku Osaka 547-0003 Japan Attention of: Atsushi Tomiyama, General Manager of QA Department Ph: +81 6 6793 8424 E-Mail: [email protected] Pre pared by Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p23b0001 John Michalowicz Project Test Engineer Thi s report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. P23b0001_FCC_ Part 80_Rev 1.0 Page 2 of 23 Te st Report Revision History Revision Date Revised By Reason for Revision 1.0 December 20, 2023 John Michalowicz Original Document P23b0001_FCC_ Part 80_Rev 1.0 Page 3 of 23 Table of Contents Description Page Standard Test Conditions Engineering Practices ................................................................................................................... 5 Test Results Summary ............................................................................................................................................................ 6 Statements of conformity ........................................................................................................................................................ 6 Modulation Requirements ....................................................................................................................................................... 7 Output Power (Conducted) ..................................................................................................................................................... 9 Conducted Spurious Emissions ............................................................................................................................................ 11 Radiated Spurious Emissions ................................................................................................................................................. 12 Emission Mask ...................................................................................................................................................................... 17 Occupied Bandwidth ............................................................................................................................................................. 19 Frequency Stability (Temperature Variation) ........................................................................................................................ 21 Frequency Stability (Voltage Variation) ................................................................................................................................. 22 Test Equipment Utilized ........................................................................................................................................................ 23 P23b0001_FCC_ Part 80_Rev 1.0 Page 4 of 23 ANAB Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2017. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A P23b0001_FCC_ Part 80_Rev 1.0 Page 5 of 23 Standard Test Conditions Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: All tests and measurement data shown were performed in accordance with FCC Rules and Regulations, Volume II; Part 2, Sub-part J, Sections 2.947, 2.1033(c), 2.1041, 2.1046, 2.1047, 2.1051, 2.1053, 2.1055, 2.1057 and the following individual Parts: FCC Part 80, ANSI C63.26-2015, and ISED RSS-182, RSS-GEN. Measurement results, unless otherwise noted, are worst-case measurements. Environmental Conditions Temperature (ºC) Humidity (%) Pressure (mbar) 17.9 – 23.9 26.0 – 35.3 961.1 – 981 EUT Description Model: IP-M60 Description: Marine Radio Serial Number: 000000000023 HVIN: 446700-01 Additional Information The EUT is a 5W Marine Radio operating between 156 and 162 MHz The push to talk radio operates from a rechargeable Li-ion battery 7.35 – 7.6 volts DC. Type of emission = G3E The manufacturer supplied the following antenna information. Type Gain Model dBi Herical -4.5 FA-SC55V-1 Herical -13.4 FA-SC59V EUT Operation during Tests The EUT was tested at 7.4 vdc under normal operation. The transmitter was set to 100% duty cycle for all tests. P23b0001_FCC_ Part 80_Rev 1.0 Page 6 of 23 Test Results Summary Specification Test Name Pass, Fail, N/A Comments FCC ISED 2.1047 80.213(a) RSS-182 Section 5.4 Modulation Requirements Pass 2.1046 80.215 (a) RSS-182 Section 5.6 Output Power (Conducted) Pass 2.1051 80.211(f) RSS-182 Section 5.9 Conducted Spurious Emissions Pass 2.1053 80.211(f) RSS-182 Section 5.9 Radiated Spurious Emissions Pass 2.1049 80.205 RSS-182 Section 5.9 Emission Mask Pass 2.1049 80.205 RSS-Gen Occupied Bandwidth Pass 2.1055 80.209(b) RSS-182 Section 5.5 Frequency Stability (Temperature Variation) Pass 2.1055, 80.209(b) RSS-182 Section 5.5 Frequency Stability (Voltage Variation) Pass Statements of conformity Statements of conformity are reported as: • Pass - the measured value is below the acceptance limit, acceptance limit = test limit. • Fail - the measured value is abo…

Text truncated - open the document above for the full version.

p23b0001_FCC_Host Integration_Rev 1.0 Page 1 of 24 Test Report Pre pared for: Icom Incorporated Mo del: IP-M60 Ser ial Number: 000000000025 Pr oject No: p23b0001 Test Results: Pass To Ho st Integration KDB 996369 FCC Part 15.209/207 and RSS-Gen (Issue 5 April 2018) Dat e of Issue: December 28, 2023 On the behalf of the applicant: Icom Incorporated 1-1-32 Kamiminami Hirano-ku Osaka 547-0003 Japan Attention of: Atsushi Tomiyama, General Manager of QA Department Ph: +81 6 6793 8424 E- Mail: [email protected] Prepared By: Compliance Testing, LLC Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com ANAB Cert#: AT-2901 FCC Site Reg. #US2901 ISED Site Reg. #2044A-2 Reviewed / Authorized By: John Michalowicz, Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. All samples were selected by the customer. p23b0001_FCC_Host Integration_Rev 1.0 Page 2 of 24 Test Results Summary Specification Test Name Pass, Fail, N/A Comments Test Date FCC RSS FCC 15.207 RSS-Gen Section 8.9 A/C Powerline Conducted Emissions N/A EUT does not transmit while charging NA FCC 15.209 RSS-Gen Section 8.9 Spurious Radiated Emissions Pass December 20, 2023 St atements of conformity are reported as: •Pass - the measured value is below the acceptance limit, acceptance limit = test limit. •Fail - the measured value is above the acceptance limit, acceptance limit = test limit. References/Methods Description ANSI C63.4-2014 Method and Measurements of Radio-Noise Emissions from low- Voltage Electrical and Electronic Equipment in the range 9kHz to 40GHz. ANSI C63.10:2020 American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices ISO/IEC 17025:2017 General requirements for the Competence of Testing and Calibrations Laboratories p23b0001_FCC_Host Integration_Rev 1.0 Page 3 of 24 Table of Contents Description Pag e Test Results Summary .................................................................................................................................. 2 Test Report Revision History ........................................................................................................................ 4 EUT Description ............................................................................................................................................ 5 Notifications ................................................................................................................................................... 6 Test and Measurement Data......................................................................................................................... 7 Test Setup and Modes of Operation ............................................................................................................. 8 Measurement Uncertainty ........................................................................................................................... 23 p23b0001_FCC_Host Integration_Rev 1.0 Page 4 of 24 Test Report Revision History Revision Date Revised By Reason for Revision 1.0 December 28, 2023 John Michalowicz Original Document Current revision of the test report replaces any prior versions. Only the current version of the test report is valid. p23b0001_FCC_Host Integration_Rev 1.0 Page 5 of 24 EUT Description Model: IP-M60 Serial: 000000000025 Firmware: V2.3 Software: NA Description: The device is a push to talk marine radio Additional Information: The EUT is battery operated and is charged via cradle. It contains the following module: FCCID: UDV-201606 IC: 23761-8PYA003 And FCCID: AFJ387300 IC: 202D-387300 Testing was performed while the Cellular and BLE radio are transmitting. Receipt of Sample(s): December 15, 2023 EUT Condition: Visual Damage No State of Development Engineering Sample/Prototype EUT PHOTO p23b0001_FCC_Host Integration_Rev 1.0 Page 6 of 24 Notifications The applicant has been cautioned as to the following: FCC 15.21 – Information to user The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27(a) – Special Accessories Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in the part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer without an additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in §2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Industry Canada Products subject to Industry Canada ICES-003 must be labeled in English and/or French (based on the intended market and any other applicable provincial or federal regulations) as follows: CAN ICES-003 (B)/NMB-003(B) p23b0001_FCC_Host Integration_Rev 1.0 Page 7 of 2…

Text truncated - open the document above for the full version.

Test Setup Photos FCC ID: IC: