AFJIC-M802IC-M802

HF MARINE TRANSCEIVER iM802 INSTRUCTION MANUAL This device complies with Part 15 of the FCC rules. Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. i IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLYbefore attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL.This manual contains important safety and operating in- structions for the IC-M802. EXPLICIT DEFINITIONS RWARNING HIGH VOLTAGE! NEVERat- tach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. RWARNING! NEVERconnect the transceiver to an AC outlet directly. This may pose a fire hazard or result in an electric shock. RWARNING! NEVERmount the transceiver (main unit) overhead. The weight of the transceiver is approximately 8 kg, but its apparent weight will in- crease several fold due to wave shocks or vibration. The transceiver must be mounted on a flat hard sur- face only. RNEVERconnect a power source of more than 16 V DC, such as a 24 V battery. This connection could cause a fire or ruin the transceiver. RNEVERplace the transceiver where normal oper- ation of the ship or vehicle may be hindered or where it could cause bodily injury. RNEVERlet metal, wire or other objects touch any internal part or connectors on the rear panel of the transceiver. This may result in an electric shock. RNEVERexpose the transceiver to rain, snow or any liquids. DO NOTuse chemical agents such as benzine or al- cohol when cleaning, as they can damage the trans- ceiver surface. During maritime mobile operation, KEEPthe trans- ceiver and microphone as far awayas possible (at least 1 m; 3 ft) from the magnetic navigation compass to prevent erroneous indications. UseIcom microphones and/or headset only (supplied or optional). Other manufacturer’s microphones and/or headset have different pin assignments, and connec- tion to the IC-M802 may damage the transceiver. AVOIDusing or placing the transceiver in areas with temperatures below –20°C (–4°F) or above +60°C (+140°F). AVOIDplacing the transceiver in excessively dusty en- vironments or in direct sunlight. AVOIDplacing the transceiver against walls or putting anything on top of the transceiver. This will obstruct heat dissipation. Place unit in a secure place to avoid inadvertent use by children. BE CAREFUL! The heatsink will become hot when op- erating the transceiver continuously for long periods. PRECAUTIONS WORDDEFINITION RR WARNING Personal injury, fire hazard or electric shock may occur. CAUTIONEquipment damage may occur. NOTE If disregarded, inconvenience only. No risk or personal injury, fire or electric shock. Icom, Icom Inc. and the are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. ii If your vessel requires assistance, contact other ves- sels and the Coast Guard by sending a distress call on 2182 kHz. Or transmit your distress call using digital selective calling on 2187.5 kHz. IN CASE OF EMERGENCY (for maritime operation) DUSING 2182 kHz WITH VOICE qPush [2182kHz] to select the emergency fre- quency. wPush [ALARM] and [TX FREQ] for 1 sec. to transmit a two tone alarm signal for at least 30 sec. • The transceiver automatically stops the alarm after 50 sec. ePush [ALARM] to turn OFF the alarm transmis- sion, then push and hold the PTT switch on the microphone and send the following information. 1. “MAY DAY, MAY DAY, MAY DAY.” 2. “THIS IS . . . . . . . . . ” (name of vessel) 3. “LOCATED AT . . . . ” (vessel's position) 4. Give the reason for the distress call. 5. Explain what assistance you need. 6. Give additional information: • Vessel type • Vessel length • Vessel color • Number of people on-board DUSING DIGITAL SELECTIVE CALLING When immediate help is needed qPush and hold [DISTRESS] for 5 sec. until the short beeps become one long beep, to send the distress call. wAfter 2182 kHz is automatically selected, trans- mit the appropriate information as at left using voice. When potential problems exists qPush [SEL], then select “All ships call” with [CH] selector. wPush and hold [CANCEL/CALL] for 5 sec. until the short beeps becomes one long beep, to use the “all ships call” function. eAfter the pre-selected frequency is selected, transmit the appropriate information using voice. • DSC equipped ships may monitor your transmission. 1 1 OPERATING RULES AND GUIDELINES Before transmitting, monitor the channel you wish to use so as to avoid interrupting transmissions al- ready in progress. • CALL PROCEDURE Calls must be properly identified and the time limit must be respected. qGive your call sign each time you call another ves- sel or coast guard station. If you have no call sign, identify the station by giving your vessel name and the name of the licensee. wGive your call sign at the end of each transmission that lasts more than 3 min. eYou must break and give your call sign at least once every 15 min. during long ship-to-shore calls. rKeep your unanswered calls short, less than 30 sec. Do not repeat a call for 2 min. tUnnecessary transmissions are not allowed. • PRIORITIES qRead all rules and regulations pertaining to priori- ties and keep an up-to-date copy handy. Safety and distress calls take priority over all others. wFalse or fraudulent distress signals are prohibited and punishable by law. • PRIVACY qInformation overheard but not intended for you, can- not lawfully be used in any way. wIndecent or profane language is prohibited. • LOGS qAll distress, emergency and safety calls must be recorded in complete details. Log data activity is usually recorded in 24 hour time. Universal Time (UTC) is frequently used. wAdjustments, repairs, channel frequency changes and authorized modifications affecting electrical op- eration of the equipment must be kept in the …

Text truncated - open the document above for the full version.

360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com © Rhein Tech Laboratories, Inc Page 57 of 70 Work Order: 2001335 Revision: Rev.5 Quote Number: QRTL01-50DB Revision: Rev.0 FCC CFR 47 Rules and Regulations and Industry Canada APPENDIX A: RF EXPOSURE FCC Rules and Regulations Part 1.1307, 1.1310, 2.1091 and 2.1093: RF EXPOSURES COMPLIANCE The manufacturer does not specify any antenna to be used with this device. This transmitter is designed to be used as a fixed locations. The antenna(s) used for this device are fixed-mounted on outdoor permanent structures. RF exposure compliance is handled during licensing by the responsible FCC bureau(s). The installer of the antenna to be used with this transmitter may be required to perform an MPE evaluation and an Environmental Assessment (EA) of the location at the time of licensing per CFR 47 Part 1.1307. Additionally, fixed mounted antennae that are co-located with other antennae must satisfy the co-location requirements of Part 1.1307, for satisfying RF exposure compliance.

360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com © Rhein Tech Laboratories, Inc. CERTIFICATE OF COMPLIANCE FCC PART 80 CERTIFICATION & INDUSTRY CANADA CERTIFICATION Test Lab: Rhein Tech Laboratories, Inc. Phone: 703-689-0368 360 Herndon Parkway Fax: 703-689-2056 Suite 1400 Web Site: www.rheintech.com Herndon, VA 20170 Applicant Information: ICOM Incorporated 12380 116 th Avenue NE Bellevue, WA 98004 USA Phone: (425) 454-8155 (Masaaki Takahashi) FCC ID: AFJIC-M802 FRN NUMBER: 0005-8553-90 EQUIPMENT TYPE: HF MARINE TRANSCEIVER MODEL(S): IC-M802 RTL WORK ORDER NUMBER: 2001335 RTL QUOTE NUMBER: QRTL01-50DB DATE OF TEST REPORT: February 1, 2002 FCC Classification: GHF– Part 80 HF Transmitter (GMDSS) GHH – Part 80 VHF Hand Held Transmitter (GMDSS) GMF – Part 80 MF Transmitter (GMDSS) GVH – Part 80 VHF Transmitter (GMDSS) MWR – Part 80 Marine Watch Receiver RNV – Part 80 Navtex Receiver TDC – Part 80 DSC Controller FCC Rule Part(s): Part 80: Stations in the Maritime Services Part 87: Aviation Services Part 90: Private Land Mobile Radio Services Industry Canada Standard: RSS-117: Land and Coast Station Transmitters Using A1, A2, A3, A2H, or A3H Emissions Operating in the 200-535 kHz Band RSS-181: Coast and Ship Station Single Sideband Radiotelephone Transmitters and Receivers Operating in the 1 605-28000 kHz Band RSS-182: Maritime Radio Transmitters and Receivers in the Band 156-162.5 MHz RSS-188: Global Maritime Distress and Safety System (GMDSS) Frequency Range (MHz) Output Power (W) Freq. Tolerance (ppm, %, or Hz) Emission Designator 1600 – 27500 kHz 150W 6 Hz 2K80J3E 1600 – 27500 kHz 150W 6 Hz 2K80H3E 1600 – 27500 kHz 150W 6 Hz 2K80J2B We, the undersigned, hereby declare that the equipment tested and referenced in this report conforms to the identified standard(s) as described in this test report. No modifications were made to the equipment during testing in order to achieve compliance with these standards. Furthermore, there was no deviation from, additions to or exclusions from the FCC Part 2, FCC Part 80, FCC Part 87, FCC Part 90 and Industry Canada standard marked above, ANSI C63.4, ANSI/TIA/EIA603 and ANSI/TIA/EIA 603-1. Signature: Date: January 10, 2002 Typed/Printed Name: K. Franck Schuppius Position: Test Engineer Signature: Date: January 10, 2002 Typed/Printed Name: Desmond A. Fraser Position: President 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com © Rhein Tech Laboratories, Inc Page 2 of 70 Work Order: 2001335 Revision: Rev.5 Quote Number: QRTL01-50DB Revision: Rev.0 FCC CFR 47 Rules and Regulations and Industry Canada TABLE OF CONTENTS 1 GENERAL INFORMATION ............................................................................................................................................... 5 1.1 SCOPE .......................................................................................................................................................................... 5 1.2 TEST FACILITY .......................................................................................................................................................... 5 1.3 RELATED SUBMITAL (S)/GRANT(S) ...................................................................................................................... 5 2 EQUIPMENT INFORMATION .......................................................................................................................................... 6 2.1 APPLICANT AND EQUIPMENT INFORMATION ................................................................................................... 6 2.2 JUSTIFICATION .......................................................................................................................................................... 6 2.3 EXERCISING THE EUT .............................................................................................................................................. 6 2.4 TEST SYSTEM DETAILS ........................................................................................................................................... 7 2.5 CONFIGURATION DIAGRAM OF TESTED SYSTEM ............................................................................................ 7 3 NECESSARY BANDWIDTH AND EMISSION BANDWIDTH - §2.202 ........................................................................ 8 3.1 BANDWIDTHS - §80.205 ............................................................................................................................................ 8 4 RF POWER OUTPUT - §2.1046 .......................................................................................................................................... 9 4.1 RF POWER OUTPUT TEST EQUIPMENT ................................................................................................................ 9 5 OCCUPIED BANDWIDTH - §2.1049................................................................................................................................ 10 5.1 OCCUPIED BANDWIDTH - §80.211 TEST PROCEDURE.....................................................................................10 5.2 OCCUPIED BANDWIDTH TEST EQUIPMENT ..................................................................................................... 10 5.3 OCCUPIED BANDWIDTH PLOTS FOR EMISSION TYPE J3E ............................................................................ 11 5.4 OCCUPIED BANDWIDTH PLOTS FOR EMISSION TYPE H3E ........................................................................... 22 5.5 OCCUPIED BANDWIDTH PLOTS FOR EMISSION TYPE J2B ............................................................................ 33 6 SPURIOUS EMISSIONS AT ANTENNA TERMINAL - §2.1051 .................................................................................. 44 6.1 SPURIOUS EMISSIONS TEST PROCEDURES....................................................................................................…

Text truncated - open the document above for the full version.

360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com © Rhein Tech Laboratories, Inc Page 67 of 70 Work Order: 2001335 Revision: Rev.5 Quote Number: QRTL01-50DB Revision: Rev.0 FCC CFR 47 Rules and Regulations and Industry Canada APPENDIX K: TEST PHOTOGRAPHS PHOTOGRAPH 1: FRONT VIEW OF RADIATED EMISSION PHOTOGRAPH 2: REAR VIEW OF RADIATED EMISSION