ALH29373220VHF FM TRANSCEIVER

© B62-1257-20 (M,E) 09 08 07 06 05 04 03 02 KENWOOD CORPORATION TK-760G series, TK-762G series/ TK-860G series, TK-862G series GEBRUIKSAANWIJZING BEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES MODE D’EMPLOI INSTRUCTION MANUAL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF VHF-FM-TRANSCEIVER/ UHF-FM-TRANSCEIVER VHF FM ZENDONTVANGER/ UHF FM ZENDONTVANGER VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL KENWOOD CORPORATION TK-760G series, TK-762G series/ TK-860G series, TK-862G series THANK YOU! We are grateful you chose KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: •TK-760G/ TK-762G:Low power VHF FM Transceiver •TK-760HG/ TK-762HG:High power VHF FM Transceiver •TK-860G/ TK-862G:Low power UHF FM Transceiver •TK-860HG/ TK-862HG:High power UHF FM Transceiver i uGOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. uILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. uREFER SERVICE TO QUALIFIED TECHNICIANS ONLY. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. WARNING! uEXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. uINJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. uDYNAMITE BLASTING CAPS Operating the transceiver within 500 feet of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container. NOTICES TO THE USER PRECAUTIONS Please observe the following precautions to prevent fire, personal injury, and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. • Do not place the transceiver in excessively dusty, humid, and/or wet areas, nor on unstable surfaces. • If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact your KENWOOD dealer. ii CONTENTS UNPACKING AND CHECKING EQUIPMENT ...................................................... 1 SUPPLIED ACCESSORIES ............................................................................ 1 PREPARATION ...................................................................................................... 2 TOOLS REQUIRED ......................................................................................... 2 POWER CABLE CONNECTION ..................................................................... 2 INSTALLING THE TRANSCEIVER ................................................................. 3 GETTING ACQUAINTED (TK-760G series/ TK-860G series) ............................ 4 FRONT PANEL AND MICROPHONE .............................................................. 4 DISPLAY ........................................................................................................... 5 REAR PANEL ................................................................................................... 5 GETTING ACQUAINTED (TK-762G series/ TK-862G series) ............................ 6 FRONT PANEL AND MICROPHNOE .............................................................. 6 DISPLAY ........................................................................................................... 7 REAR PANEL ................................................................................................... 7 PROGRAMMABLE AUXILIARY FUNCTIONS ..................................................... 8 OPERATING BASICS ............................................................................................ 9 SWITCHING POWER ON/OFF ........................................................................ 9 ADJUSTING THE VOLUME ............................................................................ 9 SELECTING A GROUP OR CHANNEL .......................................................... 9 PLACING A CALL .......................................................................................... 10 RECEIVING A CALL ...................................................................................... 10 CHANNEL SCAN (TK-760G/ TK-860G only) ..................................................... 11 PRIORITY SCAN ............................................................................................ 11 CHANNEL LOCKOUT ................................................................................... 11 REVERT CHANNEL ...................................................................................... 11 DTMF CALLS ....................................................................................................... 12 MANUAL DIALLING ...................................................................................... 12 STORING DTMF NUMBERS ..........................................…

Text truncated - open the document above for the full version.

FCC ID;ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC BLOKDIAGRAM (Bottom Left)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 BLOCKDIAGRAM (Bottom Right)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC BLOCKDIAGRAM (Top-Left)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 BLOCKDIAGRAM (Top Right)

FCC ID:ALH29373220 Model name:TK-760HG BOTTOM VIEW

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC CONTROL UNIT(Bottom Right)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC CONTROL UNIT(Bottom Left)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC CONTROL UNIT(Top Left)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 CIRCUIT SCHEMATIC CONTROL UNIT(Top Right)

FCC ID:ALH29373220 Model name:TK-760HG FRONT VIEW

FCC ID:ALH29373220 Model name:TK-760HG LefT SIDE VIEW

FCC ID:ALH29373220 MODEL NAME:TK-762HG REAR VIEW(Name Plate)

FCC ID:ALH29373220 Model name:TK-760HG TOP VIEW

FCC ID:ALH29373220 Model name:TK-760HG Rear View(Name Plate)

FCC ID:ALH29373220 Model name:TK-760HG PC BOARD VIEW REAR

FCC ID:ALH29373220 Model name:TK-760HG PC Board TOP View

FCC ID:ALH29373220(TK-760HGK2) FCC ID:ALH29373220(TK-762HGK2) 1 TK-760HG Circuit Descriptions The Kenwood model TK-760(G is an all solid-state frequency synthesized VHF/FM transceiver designed for operation in the frequency range of 136 MHz to 162 MHz (ALH29373220).TK-760(G is 128 Number of channels, and TK-762(G is 8 Number of channels. The unit consists of a TX-RX unit and LCD assembly and its transmitter is rated for 50W output power. 1. TX-RX Unit The TX-RX unit consists of a Voltage Control Oscillator (VCO) sub-unit, a receiver section, a transmitter section, a control section and a power supply section. 1.1 PLL Frequency Synthesizer The transmit signal and the receiver first L. O. signal are generated by the PLL digital frequency synthesizer. The frequency synthesizer consists of a transmitter voltage controlled oscillator (TX VCO, Q103), a receiver voltage controlled oscillator (RX VCO, Q101), a buffer amplifier (Q106), an RF amplifier (Q9), a low-pass filter, a PLL IC (IC3) and TX VCO/RX VCO switches (Q104 and Q105). In the transmit signal mode, an operating frequency programming data is sent to IC3,from the control unit, to set the programmable counter within IC3. Q104 is turned on to activate the TX VCO and the output signal of the TX VCO is amplified by Q106 and Q9 before it is routed to IC3. The signal is then divided down in frequency, at the programmable counter in IC3, to 5.0kHz or 6.25kHz which is compared in phase with a 5.0kHz or 6.25kHz reference signal, derived from 16.8MHz crystal oscillator and a 1/3360 or a 1/2688 fixed counter in IC3, at the phase comparator also in IC3. The crystal oscillator operates at 16.8MHz and its frequency stability is maintained within 2.5ppm (temperature range of –30 to +60) . The phase comparator output signal is fed into a low-pass filter before being applied to the TX VCO as a frequency control voltage. If an unlock condition occurs in the phase locked loop, this condition is detected by D9. This cause the transmitter 8V supply cut off, resulting the prevention of an unauthorized transmission. The transmitter modulation signals (processed Mic. audio and sub-audible signaling) are applied to the TX VCO for frequency modulation. In the receive mode, the VCO is substituted with Q101 (RX VCO) and it generates the receiver first local oscillator signal according to the data sent from the control unit. FCC ID:ALH29373220(TK-760HGK2) FCC ID:ALH29373220(TK-762HGK2) 2 The basic operation of the synthesizer remains the same. 1.2 Receiver Circuit The receiver is a double conversion super-heterodyne, designed to operate in the frequency range of 136 MHz to 162 MHz (ALH29373220). The receiver RF and IF sections consist of an RF amplifier (Q27), a first mixer (Q15), and an FM IF IC (IC5). An incoming RF signal from the antenna is fed into a band-pass filter which consists of L18 and variable capacitors (D30 and D31) after going through an antenna switch in the transmitter power amplifier section. The D30 and D31 will be electrically tuned by TV voltage for the best BPF response. This RF signal is then amplified by an RF amplifier (Q27) and filtered again by band-pass filters (L11, L13, L15 and D18, D23, D28). After amplification and filtering, the signal is applied to the first mixer (Q15) for mixing with the first local oscillator signal generated by the frequency synthesizer. The heterodyning action of the first mixer produces a 49.950MHz intermediate frequency (first IF), which is applied into two monolithic crystal filters. The signal out of the crystal filters is amplified by a first IF amplifier (Q13) and is sent to the FM IF IC (IC5). The FM IF IC (IC5) contains a second mixer, a second local oscillator, second IF amplifiers, a second IF filter, an FM detector and a RSSI output. The signal applied to IC5 is mixed with 50.400MHz, which produces a 450kHz second IF signal. The signal obtained at the second mixer is filtered by a 450kHz ceramic filter (CF1 for narrow or CF2 for wide) and it is amplified by limiting amplifiers. The recovered audio signal from the incoming signal is obtained from quadrature type FM demodulator. This recovered audio signal is then sent to the audio amplifier circuit and to the noise actuated squelch circuit. The recovered audio signal obtained at IC5 is de-emphasized and further amplified for driving a loud speaker. 1.3 Transmitter Circuit The transmitter circuit consists of a microphone amplifier, an RF power amplifier driver (Q22 and Q25), an RF power amplifier module (IC400), an antenna switching network, a spurious and harmonics low-pass filter, and an automatic power control (APC). The audio signal, originating at the microphone, is applied to the microphone amplifier (IC507, IC508). The audio signal is amplified, pre-emphasized (IC508), voltage limited and low-pass filtered. The signal is then switched by transistors to the TX VCO for modulating the transmit carrier signal or to public address operation. FCC ID:ALH29373220(TK-760HGK2) FCC ID:ALH29373220(TK-762HGK2) 3 The transmit signal, generated at the frequency synthesizer, is applied to the RF power amplifier driver to gain a sufficient signal level to drive the RF power amplifier. The output signal from the RF power amplifier driver is further amplified, in the RF power amplifier module, up to the level of the transmitter rated output power. This signal is routed to the antenna connector after going through the antenna switching network and the low-pass filter. This filter has a minimum attenuation of 65dB at the second harmonic frequency. This output power level once it was set it will be maintained at a constant output level by automatic power control unit (D35, D36, IC15, Q31and Q32). 1.4 Control Section The control section consists of a CPU (IC502), LCD unit and associated interface circuits. The CPU (IC502) is connected to an external EEPROM (IC505), which stores the operating frequency information. The CPU (IC502) performs the following functions:…

Text truncated - open the document above for the full version.

FCC ID:ALH29373220(TK-760HGK2) FCC ID:ALH29373220(TK-762HGK2) TK-760G Tuning procedure Before attempting to tune the transceiver, connect the unit to a suitable power supply. Whenever the transmitter tuned, unit must be connected to a suitable dummy load, unless the instruction specify otherwise. The speaker output connector must be terminated with a 4 Ohms dummy load at any time during the tuning and connected to an AC voltmeter and an audio distortion meter or a SINAD measurement at all the time during the tuning. 1.1 Enter into tuning mode Press "SCN" key while turn on the transceiver. After about 1 second, the tuning mode starts. 1.2 Frequency version selection The following operation frequency band can be chosen for the set under tuning. Panel Display Frequency VHF F2 136 to 162MHz Following keys on the panel can be used for frequency selection: 5 key Next (Up) frequency selection 6 key Next (Down) frequency selection Channel down key Enter (or confirm) Once, the channel down key is pressed the set tuning items will be started. 1.3 Transmitter tuning Use "SCN", "6" key to choose tuning item and "A", "6", ”D/A” key to adjust tuning requirement. 1.3.1 Connect a voltmeter to TP1 1.3.2 Be sure the voltage should be below 7.5V at the test channel 3 and more than 1.0V at the test channel 2 in the Transmission and Reception mode. 1.3.3 Select the test channel 1 and adjust the transmission frequency to 149.100MHz ±100Hz. 1.3.4 Select Tuning Item 2, RF power adjustment. Adjust RF output power to 50W ±2W. 1.3.5 Select Tuning Item 4, DQT balance adjustment. Adjust the DQT pulse shape to obtain neat demodulation wave-form. 1.3.6 Select Tuning Item 5, Max. deviation adjustment. Apply a 1000Hz tone with a 50mV RMS level to the Microphone input. Adjust the maximum deviation to 3.9kHz ±0.1kHz (for the Wide band), or 1.9kHz ±0.05kHz (for the Narrow band). 1.3.7 Reduce a 1000Hz tone voltage to 5mV. Be sure the deviation should be in ±2.5kHz to ±3.5kHz. 1.3.8 Select Tuning Item 6, QT deviation adjustment. Adjust the QT deviation to 0.75kHz ±50Hz (for the Wide band), or 0.35kHz ±50Hz (for the Narrow band). 1.3.9 Select Tuning Item 7, DQT deviation adjustment. Adjust the DQT deviation to 0.75kHz ±50Hz (for the Wide band), 0.35kHz ±50Hz (for the Narrow band). 1.3.10 Be sure the DTMF deviation should be in ±2.8kHz to ±3.2kHz (for the Wide band), or ±1.4kHz to ±1.6kHz (for the Narrow band). FCC ID:ALH29373220(TK-760HGK2) FCC ID:ALH29373220(TK-762HGK2) 1.4 Receiver tuning 1.4.1 Select Tuning Item 8, sensitivity adjustment. Apply a 149.050MHz to the transceiver antenna terminal. 1.4.2 Tune L11, L13, L15 and L18 to obtain the maximum receiver SINAD. 1.4.3 Tune on the frequencies of 136.050MHz and 161.950MHz, Change the TV voltage using “” and “” key to obtain the maximum receiver SINAD. 1.4.4 Select Tuning Item 9, squelch adjustment. Apply a 149.050MHz with 3dB subtracted from the sensitivity value of 12dB SINAD to the transceiver. 1.4.5 Be sure to make the squelch closed once then opened. 1.4.6 Set the RF signal level to 8dB SINAD. Confirm the squelch should be opened. 1.4.7 Turn off the RF signal. Then confirm the squelch should be closed.

SYMBOLPARTS NUMBERPARTS NAMEDISCRIPTION D1011SV283VARICAPRX VCO D1021SV283VARICAPTX VCO D1031SV283VARICAPRX VCO D1041SV283VARICAPTX VCO D105HVU363AVARICAP Q1012SK508NV(K52)FETOSC(RX) Q102DTC114EUATRANSISTORTX/RX SWITCH(RX) Q1032SK508NV(K52)FETOSC(TX) Q1042SC4081TRANSISTORTX/RX SWITCH(TX) Q1052SC4081TRANSISTORTX/RX SWITCH(RX) Q1062SC4226(R24)TRANSISTORBUFFER AMP. PARTS LIST ?TK-760HG K2 VCO UNIT (X58-4670-11) FCC ID:ALH29373220

SYMBOLPARTS NUMBERPARTS NAMEDISCRIPTION D8011SS373DIODEREVERCE CURRENT PREVENTION D802B30-2211-05LEDLIGHT EMISSON D803B30-2211-05LEDLIGHT EMISSON D804B30-2211-05LEDLIGHT EMISSON D805B30-2211-05LEDLIGHT EMISSON D808HSB123DIODECURRENT STABILITY IC801LC75823WIC Q8012SB1132(Q,R)TRANSISTORDC SWITCH(LED) PARTS LIST ?TK-760HG K2 DISPLAY UNIT (X54-3270-10) FCC ID:ALH29373220

SYMBOLPARTS NUMBERPARTS NAMEDISCRIPTION D1HSB123DIODESURGE ABSORPTION D202DZ20(Y,Z)DIODEVOLTAGE REFERRENCE D3HSB123DIODESURGE ABSORPTION D4HSB123DIODESURGE ABSORPTION D5HSB123DIODESURGE ABSORPTION D8DAN235KDIODEIF SWITCH (WIDE/NARROW) D91SS355DIODE SWITCH D10DAN235KDIODEIF SWITCH (WIDE/NARROW) D11MA742DIODELIMITTER D141SS355DIODESURGE ABSORPTION D15DAN202KDIODEOR GATE D16DAN235KDIODE D171SS355DIODETEMPERATURE COMPENSATION D18HVC350BVARICAPRF BPF TUNEING D191SS355DIODESURGE ABSORPTION D201SS355DIODEREVERCE CURRENT PREVENTION D2102DZ18(X,Y)ZENER DIODEVOLTAGE REFERRENCE D22HSB123DIODETEMPERATURE COMPENSATION D23HVC350BVARICAPRF BPF TUNEING D2402DZ15(X,Y)ZENER DIODEVOLTAGE REFERRENCE D26DSA3A1-FKDIODEREVERCE CURRENT PREVENTION D271SS355DIODEREVERCE CURRENT PREVENTION D28HVC350BVARICAPRF BPF TUNEING D30HVC350BVARICAPRF BPF TUNEING D31HVC350BVARICAPRF BPF TUNEING D33XB15A709DIODEANT SW D34MA4PH633DIODEANT SW D35MA742DIODEAPC VOLTAGE DITECT D36MA742DIODEAPC VOLTAGE DITECT D39UDZ4.7(B)ZENER DIODEVOLTAGE REFERRENCE D40MA742DIODELIMITTER D501MA2S111DIODEREVERCE CURRENT PREVENTION D502MA2S111DIODEREVERCE CURRENT PREVENTION D503MA2S111DIODEREVERCE CURRENT PREVENTION D504MA2S111DIODEREVERCE CURRENT PREVENTION D505MA2S111DIODEREVERCE CURRENT PREVENTION D507MA2S111DIODEREVERCE CURRENT PREVENTION D508MA742DIODELIMITTER D509B30-2171-05LEDLIGHT EMISSON D510B30-2171-05LEDLIGHT EMISSON D511B30-2171-05LEDLIGHT EMISSON D512B30-2171-05LEDLIGHT EMISSON PARTS LIST ?TK-760HG (K2) TX/RX UNIT (X57-5950-16) FCC ID:ALH29373220 D513B30-2171-05LEDLIGHT EMISSON D514B30-2171-05LEDLIGHT EMISSON D521B30-2151-05LEDLIGHT EMISSON D523DAN202UDIODEOR GATE D524HSB123DIODESURGE ABSORPTION SYMBOLPARTS NUMBERPARTS NAMEDISCRIPTION D525HSB123DIODESURGE ABSORPTION D5261812L075PRPOLY SWCURRENT PROTECTION D527HSB123DIODESURGE ABSORPTION D528HSB123DIODESURGE ABSORPTION D529MA742DIODELIMITTER IC1TA75S01FICSUM AMPLIFIER IC2TA75S01FICAMPLIFIER IC3MB15A02ICPLL SYNTHESIZER IC4NJM4558MICAMPLIFIER IC5TA31136FNICFM DEMODULATION IC6M62363FPICD/A CONVERT IC7NJM2904ICAMPLIFIER IC8UPB1509GVICPRESCALER IC9BU4094BCFICSHIFT/STORE RESISTER IC10NJM78L05UAIC5V AVR IC11AN8009MIC8V AVR IC12TA7808SIC8V AVR IC13LA4422ICAF AMP IC14TC4013BF(N)ICPOWER SUPPLY LOGIC CIRCUIT CONTROL IC15TA75S01FICAMPLIFIER IC400M68702LICPOWER MODULE IC501AT29C020-90TIICFLASH ROM IC50230622M4102GPICCPU IC503RH5VL42CICRESET IC IC505AT2408N10SI2.5ICEEPROM IC507NJM2904VICAMPLIFIER IC508TC35453FICAUDIO PROCESSER IC509BU4066BCFVICANALOG SWITCH IC510BU4094BCFVICSHIFT/STORE RESISTER IC511LC73872MICDTMF DECODE IC512NJM78L05UAIC5V AVR IC513TA75W588FUICAMPLIFIER IC514TA75W588FUICAMPLIFIER Q1DTD114EKTRANSISTORDC SWITCH (HOR) Q2DTA114EKATRANSISTORDC SWITCH (5S) Q3DTA114EKATRANSISTORDC SWITCH (W/N) Q4DTA114EKATRANSISTORDC SWITCH (W/N) Q5DTA114EKATRANSISTORDC SWITCH (HNC) Q6DTA114EKATRANSISTORDC SWITCH (IGN.) Q72SC4649(N,P)TRANSISTORBUFFER AMP. Q82SC2412KTRANSISTOR FILTER Q92SC5110(O)TRANSISTORBUFFER AMP. Q10DTC114EKATRANSISTORNOISE AMP. Q112SA1832(GR)TRANSISTORCHARGE POMP Q122SC4738(GR)TRANSISTORCHARGE POMP Q132SC4649(N,P)TRANSISTORIF AMP Q142SC4649(N,P)TRANSISTORBUFFER AMP. Q153SK228FETMIXER Q16DTC114EKATRANSISTORDC SWITCH (8R) Q17DTC363EUTRANSISTORAF MUTE Q182SA1745(6,7)TRANSISTORDC SWITCH (8R) SYMBOLPARTS NUMBERPARTS NAMEDISCRIPTION Q19DTC114EKATRANSISTORDC SWITCH (SB) Q20DTA114EKATRANSISTORDC SWITCH (SB) Q21DTC114EKATRANSISTORDC SWITCH (SB) Q222SC3357TRANSISTORRF AMP. Q232SA1641(S,T)TRANSISTORDC SWITCH (SB) Q24DTA114EKATRANSISTORAF MUTE Q252SC2954TRANSISTORRF AMP. Q26DTA114EKATRANSISTORDC SWITCH (PSW) Q273SK241(R)FETL.N.A Q282SB1132(Q,R)TRANSISTORDC SWITCH (8T) Q29DTC114EKATRANSISTORDC SWITCH (8T) Q312SC2412KTRANSISTORAPC CONTROLLER Q322SB1565(E,F)TRANSISTORAPC CONTROLLER Q33DTC114EKATRANSISTORAPC CONTROLLER Q362SC2412KTRANSISTORDC SWITCH(POWER) Q372SK1824FETAF SWITCH Q382SK1824FETDC SWITCH(5S) Q5012SC4619TRANSISTORCLOCK SHIFT Q502DTC114EETRANSISTORAF MUTE Q503DTC114EETRANSISTORDC SWITCH(PA2) Q5042SC4617(S)TRANSISTORDC SWITCH(LED) Q5052SB1132(Q,R)TRANSISTORDC SWITCH(LED) Q506DTC114EETRANSISTORDC SWITCH(LED) Q5082SC4617(S)TRANSISTORDC SWITCH(LED) Q509DTC363EUTRANSISTORMIC MUTE

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 PARTS LIST(General-1)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 PARTS LIST(General-2)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 PARTS LIST(General-3)

FCC ID:ALH29373220 MODEL NAME:TK-760HGK2 PARTS LIST(General-4)

FCC ID: ALH29373220 MFA p0070013, d00a0049 Date: October 26, 2000 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood Communications Corporation Equipment: TK-760HG-2 and TK-762HG-2 FCC ID: ALH29373220 FCC Rules: Radiofrequency Radiation Exposure Limits 47 CFR 1.1310 (MPE - Mobiles) Gentlemen: On behalf of the Applicant, enclosed please find the Supplemental Test Data Report, the whole for Environmental Assessment (MPE) of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: ALH29373220 MFA p0070013, d00a0049 ENVIRONMENTAL ASSESSMENT for MOBILES for FCC ID: FCC ID: ALH29373220 Model:TK-760HG-2 and TK-762HG-2 to FEDERAL COMMUNICATIONS COMMISSION 47 CFR 1.1310 (MPE) Radiofrequency Radiation Exposure Limits DATE OF REPORT: October 26, 2000 ON THE BEHALF OF THE APPLICANT: Kenwood Communications Corporation AT THE REQUEST OF: P.O. 40470 Kenwood Communications Corporation P.O. Box 22745 Long Beach, CA 90801-5745 Attention of: Joel E. Berger, Research & Development [email protected] (310) 761-4409; FAX: -8246 SUPERVISED BY: Morton Flom, P. Eng. FCC ID: ALH29373220 MFA p0070013, d00a0049 TABLE OF CONTENTS RULEDESCRIPTIONPAGE . Test Report 1 . Identification of the Equipment Under Test 2 . Standard Test Conditions and Engineering Practices 4 1.1310 Environmental Assessment 5 FCC ID: ALH29373220 MFA p0070013, d00a0049 PAGE NO.1of6. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) TEST REPORT (SUPPLEMENTAL) b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044) M. Flom Associates, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d00a0049 d) Client: Kenwood Communications Corporation P.O. Box 22745 Long Beach, CA 90801-5745 e) Identification: TK-760HG-2 and TK-762HG-2 FCC ID: ALH29373220 Description: VHF FM Transceiver f) EUT Condition: Not required unless specified in individual tests. g) Report Date: October 26, 2000 EUT Received: July 18, 2000 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: Morton Flom, P. Eng. n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. FCC ID: ALH29373220 MFA p0070013, d00a0049 PAGE NO.2of6. IDENTIFICATION OF THE EQUIPMENT UNDER TEST (EUT) NAME AND ADDRESS OF APPLICANT: Kenwood Communications Corporation 2201 E. Dominguez St P.O. Box 22745 Long Beach, CA 90801-5745 MANUFACTURER: Kenwood Electronics Technologies PTE Ltd. 1 Ang Mo Kio Street 63 Singapore 569110 FCC ID: ALH29373220 MODEL NO: TK-760HG-2 and TK-762HG-2 DESCRIPTION: VHF FM Transceiver TYPE OF EMISSION: 16K0F3E, 11K0F3E FREQUENCY RANGE, MHz: 136 to 162 POWER RATING, Watts: 10to50 Switchable x Variable N/A MODULATION: AMPS TDMA CDMA x F3E ANTENNA: HELICAL MONOPOLE WHIP x OTHER NOTE: For RF Safety test antenna gain taken at the upper range of expected gain (i.e. 0 dBd) and RF Power set to highest nominal power across all channels. FCC ID: ALH29373220 MFA p0070013, d00a0049 PAGE NO.3of6. M. Flom Associates, Inc. is accredited by the American Association for Laboratory Association (A2LA) as shown in the scope below. "This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this report have been determined in accordance with the laboratory's terms of accreditation unless stated otherwise in the report." Should this report contain any data for tests for which we are not accredited, or which have been undertaken by a subcontractor that is not A2LA accredited, such data would not covered by this laboratory's A2LA accreditation. FCC ID: ALH29373220 MFA p0070013, d00a0049 PAGE NO.4of6. STANDARD TEST CONDITIONS and ENGINEERING PRACTICES Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.4-1992/2000, section 6.1.9, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10°to 40°C (50°to 104°F) unless the particular equipment requirements specify testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Prior to testing, the EUT was tuned up in accordance with the manufacturer's alignment procedures. All external gain controls were maintained at the position of maximum and/or optimum gain throughout the testing. Measurement results, unless otherwise noted, are worst case measurements. FCC ID: ALH29373220 MFA p0070013, d00a0049 PAGE NO.5of6. Name of test:Environmental Assessment Specification:FCC: 47 CFR 1.1310 Measurement Guide:ANSI/IEEE C95.1 1992 Test Equipment:Maximum Permissible Exposure (MPE) measurement system, consisting of: Narda 8717-1174R, Radiation meter Narda 8761D, E-field probe (300 kHz – 3 GHz) (Calibrated Nov-98) Measurement Procedure: 1. The following measurements were performed with a Narda probe using ANSI/IEEE C95.1 as a guide. 2. Prior to making any measurements, the measurements system was calibrated in accordance with the manufacturer’s procedures. 3. The EUT’s radiating element (antenna) was placed ona1mtall table for ease of testing. For equipment normally operated on a metal surface, a ground plane was used. 4. The remaining equipment necessary to operate the EUT was maintained at a distance from the measurement arrangement suitable to minimize interference with the measurements. 5. The minimum safe distance was calculated from the formula Power Density = EIRP / 4πR 2 (Peak Watts/m 2 ). The calculation is shown…

Text truncated - open the document above for the full version.

FCC ID: ALH29373220 MFA p0070013, d0070093 TRANSMITTER CERTIFICATION of FCC ID: ALH29373220 MODELS : TK-760HG-2 and TK-762HG-2 to FEDERAL COMMUNICATIONS COMMISSION Rule Part(s) 22, 74, 90 DATE OF REPORT: October 26, 2000 ON THE BEHALF OF THE APPLICANT: Kenwood Communications Corporation AT THE REQUEST OF: P.O. 40470 Kenwood Communications Corporation P.O. Box 22745 Long Beach, CA 90801-5745 Attention of: Joel E. Berger, Research & Development [email protected] (310) 761-4409; FAX: -8246 SUPERVISED BY: Morton Flom, P. Eng. FCC ID: ALH29373220 MFA p0070013, d0070093 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. FCC ID: ALH29373220 MFA p0070013, d0070093 TABLE OF CONTENTS RULEDESCRIPTIONPAGE . Test Report 1 2.1033(c) General Information Required 2 2.1033(c)(14) Rule Summary 5 . Standard Test Conditions and Engineering Practices 6 2.1046(a) Carrier Output Power (Conducted) 7 2.1051 Unwanted Emissi…

Text truncated - open the document above for the full version.