ALH3226311022, 74, 90, 95

© B62-XXXX-00 (K) 09 08 07 06 05 04 03 02 01 00 KENWOOD CORPORATION INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-2140 TK-3140 UHF FM TRANSCEIVER i WARNING: EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn off your transceiver while taking on fuel, or while parked in gasoline service stations. uGOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. uILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. uREFER SERVICE TO QUALIFIED TECHNICIANS ONLY. SAFETY: It is important that the operator is aware of and understands hazards common to the operation of any transceiver. THANK YOU We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL • TK-2140: VHF FM Transceiver • TK-3140: UHF FM Transceiver NOTICES TO THE USER ii One or more of the following statements may be applicable: ATTENTION (U.S.A. Only): The RBRC Recycle seal found on KENWOOD nickel-cadmium (Ni-Cd) battery packs indicates KENWOOD’s voluntary participation in an industry program to collect and recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste streams, which is illegal in some areas. For information on Ni-Cd battery recycling in your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). KENWOOD’s involvement in this program is part of our commitment to preserve our environment and conserve our natural resources. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer for technical assistance. iii CONTENTS UNPACKING AND CHECKING EQUIPMENT................... 1 Supplied Accessories...................................... 1 PREPARATION.................................................. 2 Installing/ Removing the (Optional) Li-ion Battery Pack .. 2 Installing the (Optional) Antenna........................ 3 Installing the Belt Clip..................................... 3 Installing the Cover over the Universal Connector..... 4 Installing the (Optional KMC-25) Speaker/ Microphone ... 4 GETTING ACQUAINTED........................................ 5 Display...................................................... 7 PROGRAMMABLE AUXILIARY FUNCTIONS................. 8 OPERATION OVERVIEW....................................... 10 Trunking Format........................................... 10 Conventional Format..................................... 10 OPERATING BASICS........................................... 11 Switching Power ON/ OFF................................ 11 Adjusting the Volume..................................... 11 Selecting a System/ Group/ Channel................... 11 Time-out Timer (TOT).................................... 12 TRUNKED OPERATION (Trunking Format).................. 13 Placing a Dispatch Call.................................. 13 Receiving a Dispatch Call................................ 13 CONVENTIONAL OPERATION (Trunking Format)........... 14 Transmitting............................................... 14 Receiving.................................................. 14 iv SYSTEM SCAN (Trunking Format)........................... 15 Scanning Trunked Systems.............................. 15 Scanning Conventional Systems........................ 15 Scan Lockout.............................................. 16 Scan Revert................................................ 16 GROUP SCAN (Trunking Format)............................ 17 CONVENTIONAL OPERATION (Conventional Format)..... 18 Transmitting............................................... 18 Receiving.................................................. 18 SCAN (Conventional Format)................................ 19 Priority Scan............................................... 19 2-TONE SIGNALLING (Conventional Format).............. 20 FleetSync™: ALPHANUMERIC 2-WAY PAGING FUNCTION ...21 Key Functions............................................. 21 Selcall (Selective Calling)............................... 22 Status Message........................................... 23 Optional Short Messages Feature...................... 26 AUDIBLE USER FEEDBACK TONES.......................... 27 1 UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWO…

Text truncated - open the document above for the full version.

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Reference: This equipment meets the requirements of FCC Rules, Parts 90.203(e) and (g) as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel. E. Berger Staff Engineer Kenwood Communications Corporation Research & Development Department Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter will authorize the appointment of MORTON FLOM, P. Eng. and/or M. Flom Associates, Inc. to act as our agent in all FCC matters. This appointment is effective until you are otherwise notified by us. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The application is not subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 USC 8.62, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel E. Berger Staff Engineer Research & Development Department Kenwood Communications Corporation Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

FCC ID: ALH32263110 Model Name: TK-3140K Name Plate FCC ID: ALH32263110 Model Name: TK-3140K Front View FCC ID: ALH32263110 Model Name: TK-3140K Rear View FCC ID: ALH32263110 Model Name: TK-3140K Top View FCC ID: ALH32263110 Model Name: TK-3140K Bottom View FCC ID: ALH32263110 Model Name: TK-3140K Right View FCC ID: ALH32263110 Model Name: TK-3140K Left View

FCC ID: ALH32263110 Model Name: TK-3140K Name Plate

FCC ID: ALH32263110 Model Name: TK-3140K PC Board: Front View FCC ID: ALH32263110 Model Name: TK-3140K PC Board: Rear View

FCC ID: ALH32263110 1 TK-3140 Circuit Description The KENWOOD model TK-3140 is a UHF/FM hand-held transceiver designed to operate in the frequency range of 450 to 490 MHz. (FCC ID: ALH32263110). The unit consists of a receiver, a transmitter, a phase-locked loop (PLL) frequency synthesizer, a digital control unit, power supply circuits and a signaling unit. 1. RECEIVER CIRCUIT The receiver is double conversion superheterodyne, designed to operate in the frequency range of 450MHz to 490MHz (FCC ID: ALH32263110). 1.1 FRONT-END RF AMPLIFIER An incoming signal from the antenna is applied to an RF amplifier (Q207) after passing through a transmit/receive switching circuit (D104 and D105 are off). After the signal is amplified, the signal is filtered by a Band-shift type band-pass filter to eliminate unwanted signals before it is routed to the first mixer. 1.2 FIRST MIXER The signal from the RF amplifier is heterodyned with the first local oscillator signal from the PLL frequency synthesizer circuit at the first mixer (Q206) to become a 44.85MHz first intermediate frequency (IF) signal. The first IF signal is fed through two monolithic crystal filters (MCFs: XF201) to further remove spurious signals. 1.3 IF AMPLIFIER The first IF signal is amplified by Q205, and then enters IC200 (FM IC).The signal is heterodyned again with a second local oscillator signal with in IC200 to become a 455kHz second IF signal. The second IF signal is fed through a 455kHz ceramic filter , CF200 (for Wide), CF201 (for Narrow) to further eliminate undesired signals before it is amplified and FM detected in IC200. 1.4 AUDIO AMPLIFIER The recovered audio signal obtained from IC200 is amplified by IC300, The audio signal is then passed through an audio frequency switch (Q204),low-pass filtered by IC500 high-pass filtered by IC500 and band-eliminate filtered by IC500. and de-emphasized by IC500. The processed audio signal passes through an audio volume control and is amplified to a sufficient level to drive a loudspeaker by an audio power amplifier (IC313) display board. 1.5 SQUELCH AND MUTE CIRCUIT The output signal from the squelch circuit, which consists of IC200,IC201 and Q208, is applied to the microprocessor. The microprocessor passes information to the shift register (IC311, IC312) and it controls the mute control lines (AF MUTE and AC) according to the input signal (noise pulse) and the microprocessor task condition. 2. TRANSMITTER 2.1 MICROPHONE CIRCUIT The signal from the microphone is high-pass filtered by IC500, passed through microphone mute circuit (Q501), limited and pre-emphasized by IC500. FCC ID: ALH32263110 2 2.2 MODULATOR CIRCUIT The output of the low-pass filter network (IC500) is passed to the D/A converter (IC307) for maximum deviation adjustment and the summing amplifier (IC305) before being applied to a varactor diode (D5) in the voltage controlled oscillator (VCO) located in the frequency synthesizer section. 2.3 DRIVER AND FINAL POWER AMPLIFIER CIRCUITS The transmit signal is directly generated by the VCO. The transmit signal obtained from the VCO buffer amplifier Q8, is amplified by Q100 and Q101, to approximately 17dBm. This amplified signal is passed to the power amplifier, Q103, Q106, consist of a 2-stage FET amplifier and is capable of producing up to 4W. 2.4 TRANSMIT/RECEIVE SWITCHING CIRCUIT The power module output signal is passed through a 3-stage low-pass filter network and a transmit/receive switching circuit before it is passed to the antenna terminal. The transmit/receive switching circuit is comprised of D102, D103. D104 and D105 are turned on (conductive) in transmit mode and turned off (isolated) in receive mode. 2.5 AUTOMATIC POWER CONTROL(APC)CIRCUIT AND TRANSMITTER OUTPUT LEVEL SWITCH The automatic power control (APC) circuit stabilizes the transmitter output power at a pre-determined level by sensing the collector current of the final RF amplifier FET. The voltage comparator (IC100) compares the voltage obtained by the above collector current with a reference voltage, set using the microprocessor and Q107. An APC voltage proportional to the difference between the sensed voltage and the reference voltage appears at the output of IC100. This output voltage controls the gate of the FET power amolifier, which keeps the transmitter output power constant. The transmitter output power can be varied to lW by the microprocessor, which in turn changes the reference voltage of IC300, and hence the output power. 3. PLL FREQUENCY SYNTHESIZER 3.1 PLL The frequency step of the PLL circuit is 5 or 6.25kHz. A 16.8MHz reference oscillator signal is divided at IC1 by a fixed counter to produce the 5 or 6.25kHz reference frequency. The VCO output signal is buffer amplified by Q1, then divided in IC1, by a dual-modules programmable counter in this case. The divided signal is compared in phase with the 5 or 6.25kHz reference signal in the phase comparator also in IC1. The output signal from the phase comparator is low-pass filtered and passed to the VCO to control the oscillator frequency. 3,.2 VOLTAGE CONTROLLED OSCILLATOR (VCO) The operating frequency is generated by voltage controlled oscilator (VCO) in transmit mode and VCO in receive mode. The oscillator frequency is controlled by applying the VCO control voltage, obtained from the phase comparator to the varactor diodes. The TX/RX pin is set high in receive mode causing IC312, and turn on. 3.3 UNLOCK DETECTOR CIRCUIT If a pulse signal appears at the LD pin of IC1, an unlock condition occurs, the DC voltage, causes the voltage applied to the UL pin of the microprocessor to go low. When the microprocessor detects this condition, the transmitter is disabled by ignoring the push-to-talk switch input signal. FCC ID: ALH32263110 3 4. DIGITAL CONTROL CIRCUIT 4.1 KEY SWITCHES AND ROTARY ENCODER INPUT CIRCUIT The key switches and rotary encoder (channel selector) in formation are entered directly into the microprocessor (IC309). 4.2 RESET CIRCUIT Wh…

Text truncated - open the document above for the full version.

FCCID: ALH32263110 1 TK-3140 Tuning procedure Before attempting to tune the transceiver, connect the unit to a suitable power supply. Whenever the transmitter tuned, unit must be connected to a suitable dummy load, unless the instruction specify otherwise. The speaker output connector must be terminated with a 16 Ohm dummy load at any time during the tuning and connected to an AC voltmeter and an audio distortion meter or a SINAD measurement at all the time during the tuning. Power sw on during "A" push to test mode [1-1] then push "S" to tuning mode. This *** mean using 3 numbers from CHANNEL NOB. 1 Transmitter section 1.1 Frequency adjustment Set test mode CH1,Push "S" to enter tuning mode, Select [FREQ***], then PTT on. 470.100MHz50Hz. 1.2 TX High power adjustment Set test mode CH1,Push "S" to enter tuning mode, Select Hpow, Push "A" to 5 points. a) Select [L Hpow***] then PTT on 4.0W0.1W. b) Push "C" to select [L2 Hpow***] then PTT on, push "B" after tuned. c) Push "C" to select [C Hpow ***] then PTT on, push "B" after tuned. d) Push "C" to select [H2Hpow***] then PTT on, push "B" after tuned. e) Push "C" to select [H Hpow***] then PTT on, push "S" to return test mode. The TX current is 2.2A or less. 1.3 TX Low power adjustment Set test mode CH1,Push "S" to enter tuning mode, Select L pow, Push "A" to 5 points. a) Select [L Lpow***] then PTT on 1.0W0.1W. b) Push "C" to select [L2 Lpow***] then PTT on, push "B" after tuned. c) Push "C" to select [C Lpow***] then PTT on, push "B" after tuned. d) Push "C" to select [H2 Lpow***] then PTT on, push "B" after tuned. e) Push "C" to select [H Lpow***] then PTT on, push "S" to return test mode. The TX current is 1.0A or less. 1.4 DQT BAL adjustment Set test mode CH1,Push "S" to enter tuning mode, Select [BAL***], Push "A" to enter 3 Points, a) Select [LBAL***] adjustments mode then PTT on Push "B" after tuned . b) Push "C" to select [C BAL***] then PTT on push "B" after tuned. c) Push "C" to select [H BAL***] then PTT on push "B" after tuned. Push "A" to return to tuning mode. d) Push "Lamp" to narrow adjustment mode [n BAL***],then PTT on push "B" after tuned. Push "Lamp" to return tuning mode. Make the de-modulation waves into square waves. 1.5 Max deviation adjustment Set test mode CH1, push "S" to enter tuning mode, Push "A" to 3 points adjustment mode. FCCID: ALH32263110 2 a) Select [L MAX***] then PTT on push "B" after tuned. b) push "C" to select [C MAX***] then PTT on push "B" after tuned. c) push "C" to select [H MAX***] then PTT on push "B" after tuned Push "A" to return tuning mode. Deviation 3.80KHz(Wide),1.75KHz(Narrow) Push " Lamp" to narrow adjustment mode [n MAX***] then PTT on push "Lamp" to return tuning mode. 1.6 QT Deviation adjustment a) Push "S" to enter tuning mode select [FQT***] push "A" to adjustment mode. Select [L FQT***] then PTT on push "B" after tuned. Deviation 0.75KHz.(0.05KHz) (Wide) 0.35KHz (0.05KHz)(Narrow) b) same [C FQT***] c) same [H FQT***] d) same [n FQT***] 1.7 DQT Deviation adjustment a) same as QT. Select [ FDQT***] b) same as [L FDQT***] c) same as [C FDQT***] d) same as [H FDQT***] e) same as [n FDQT***] Deviation 0.75KHz(0.05KHz) (Wide) 0.35KHz (0.05KHz)(Narrow) 1.8 LTR Deviation adjustment a) Select [ FLTR***] b) Select [L FLTR***] c) Select [C FLTR***] d) Select [H FLTR***] e) Select [n FLTR***] Deviation 1.0KHz(0.05KHz)(Wide) 0.75KHz(0.05KHz)(Narrow) 1.9 DTMF Deviation adjustment a) Select [DTMF***] Deviation 3KHz(0.05KHz)(Wide) b) Select [n DTMF***] Deviation 1.5KHz(0.05KHz)(Narrow) 1.10 MSK Deviation adjustment a) Select [FMSK***] Deviation3KHz(0.05KHz)(Wide) b) Select [n MSK***] Deviation1.5KHz(0.05KHz)(Narrow) 2 Receiver section 2.1 Sensitivity a) Select [SENS***] , Push "A" to 5 points. b) Push "C" to select [L SENS***] to get best Sensitivity , then push "B" after tuned c) Push "C" to select [L2 SENS***] to get best Sensitivity , then push "B" after tuned d) Push "C" to select [C SENS ***] to get best Sensitivity , then push "B" after tuned e) Push "C" to select [H2 SENS***] to get best Sensitivity , then push "B" after tuned FCCID: ALH32263110 3 f) Push "C" to select [H SENS***] to get best Sensitivity , then push "B" after tuned g) push "A" to return test mode. 2.2 Open squelch adjustment a) Push “A” to 3 point ( SSG level : 12dB SINAD) b) Select [OSQL***] Adjust to point of opening squelch.(Wide) c) Select [OSQL***] Adjust to point of opening squelch d) Select [OSQL***] Adjust to point of opening squelch e) Select [n OSQL***] Adjust to point of opening squelch.(Narrow) 2.3 Tight squelch adjustment a)Push “A” to 3 point ( SSG level : 12dB SINAD + 5 dB) b) Select [TSQL***] Adjust to point of opening squelch.(Wide) c) Select [TSQL***] Adjust to point of opening squelch d) Select [TSQL***] Adjust to point of opening squelch f) Select [n TSQL***] Adjust to point of opening squelch.(Narrow)

CELLTECH RESEARCH INC. Test Report S/N: 082901-159ALH 1955 Moss Court, Kelowna Date(s) of Tests: August 29, 2001 B.C. Canada V1Y 9L3 FCC SAR Measurements _____________________________________________________________________________________________________________ © 2001 Celltech Research Inc. CERTIFICATE OF COMPLIANCE SAR EVALUATION This wireless portable device has been shown to be compliant for localized Specific Absorption Rate (SAR) for controlled environment / occupational exposure limits specified in ANSI/IEEE Std. C95.1-1992 and has been tested in accordance with the measurement procedures specified in ANSI/IEEE Std. C95.3-1999. I attest to the accuracy of data. All measurements were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Celltech Research Inc. certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Shawn McMillen General Manager Celltech Research Inc. Test Lab: CELLTECH RESEARCH INC. Testing and Engineering Lab 1955 Moss Court Kelowna, B.C. Canada V1Y 9L3 Phone: 250 - 860-3130 Fax: 250 - 860-3110 Toll Free: 1-877-545-6287 e-mail: [email protected] web site: www.celltechlabs.com Applicant Information: KENWOOD COMMUNICATIONS CORP. 2201 East Dominguez Street PO Box 22745 Long Beach, CA 90801-5745 FCC Rule Part(s): 2.1093; ET Docket 96-326 FCC ID: ALH32263110 Model(s): TK-3140-1 EUT Type: Portable UHF PTT Radio Transceiver Modulation: FM (UHF Band) Tx Frequency Range: 4.3 Watts (450.05 MHz) 4.5 Watts (470.05 MHz) 4.4 Watts (489.95 MHz) Antenna Type(s): #1: Helical Whip (KRA-15M) #2: Helical Stubby (KRA-23M) CELLTECH RESEARCH INC. Test Report S/N: 082901-159ALH 1955 Moss Court, Kelowna Date(s) of Tests: August 29, 2001 B.C. Canada V1Y 9L3 FCC SAR Measurements _____________________________________________________________________________________________________________ © 2001 Celltech Research Inc. TABLE OF CONTENTS 1.0 INTRODUCTION.................................................................. 1 2.0 DESCRIPTION OF EUT.......................................................... 1 3.0 SAR MEASUREMENT SYSTEM ............................................. 2 4.0 MEASUREMENT SUMMARY.................................................. 3-4 5.0 DETAILS OF SAR EVALUATION............................................ 5 6.0 EVALUATION PROCEDURES................................................. 5 7.0 SAR LIMITS........................................................................ 6 8.0 SYSTEM VALIDATION.......................................................... 6 9.0 SIMULATED EQUIVALENT TISSUES...................................... 7 10.0 TISSUE PARAMETERS......................................................... 7 11.0 SYSTEM SPECIFICATIONS.................................................... 8 12.0 PROBE SPECIFICATION....................................................... 9 13.0 GENERIC TWIN PHANTOM................................................... 9 14.0 DEVICE HOLDER................................................................. 9 15.0 TEST EQUIPMENT LIST........................................................ 10 16.0 MEASUREMENT UNCERTAINTIES........................................ 11 17.0 REFERENCES...................................................................... 12 APPENDIX A - SAR MEASUREMENT DATA........................................ 13 APPENDIX B - DIPOLE VALIDATION................................................ 14 APPENDIX C - PROBE CALIBRATION............................................... 15 APPENDIX D - SAR TEST SETUP PHOTOGRAPHS............................... 16 CELLTECH RESEARCH INC. Test Report S/N: 082901-159ALH 1955 Moss Court, Kelowna Date(s) of Tests: August 29, 2001 B.C. Canada V1Y 9L3 FCC SAR Measurements _____________________________________________________________________________________________________________ © 2001 Celltech Research Inc. KENWOOD FCC ID: ALH32263110 (Model: TK-3140-1) 1 Portable UHF PTT Radio Transceiver (450-490MHz) 1.0 INTRODUCTION This measurement report shows compliance of the KENWOOD Model: TK-3140-1 Portable UHF PTT Radio Transceiver FCC ID: ALH32263110 with the regulations and procedures specified in FCC Part 2.1093, ET Docket 96-326 Rules for mobile and portable devices (controlled exposure). The test procedures, as described in American National Standards Institute C95.1-1992 (1), FCC OET Bulletin 65, Supplement C (Edition 01-01) were employed. A description of the product and operating configuration, detailed summary of the test results, methodology and procedures used in the evaluation, equipment used, and the various provisions of the rules are included within this test report. 2.0 DESCRIPTION of Equipment Under Test (EUT) Rule Part(s) FCC 2.1093; ET Docket 96.326 Modulation FM (UHF Band) EUT Type Portable UHF PTT Radio Transceiver Tx Frequency Range (MHz) 450 - 490 FCC ID ALH32263110 Conducted Output Power Tested 4.3 W (450.05MHz) 4.5 W (470.05MHz) 4.4 W (489.95MHz) Model No.(s) TK-3140-1 Antenna Type(s) Helical Whip (KRA-15M) Helical Stubby (KRA-23M) Serial No. Pre-production Battery Type Ni-Cd 1200mAh 7.2 VDC EUT with KRA-15M Whip Antenna Right Side of EUT Left Side of EUT Back Side of EUT EUT with Speaker/Mic EUT with KRA-23M Stubby Antenna CELLTECH RESEARCH INC. Test Report S/N: 082901-159ALH 1955 Moss Court, Kelowna Date(s) of Tests: August 29, 2001 B.C. Canada V1Y 9L3 FCC SAR Measurements _____________________________________________________________________________________________________________ © 2001 Celltech Research Inc. KENWOOD FCC ID: ALH32263110 (Model: TK-3140-1) 2 Portable UHF PTT Radio Transceiver (450-490MHz) 3.0 SAR MEASUREMENT SYSTEM Celltech Research SAR measurement facility utilizes the Dosimetric Assessment System (DAS…

Text truncated - open the document above for the full version.

FCC ID: ALH32263110 MFA p0170004, d0180024 Date of Report: Date of Submission: August 8, 2001 September 10, 2001 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Kenwood Communications Corporation Equipment: TK-3140-1 FCC ID: ALH32263110 FCC Rules: 22, 74, 90, 95 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: ALH32263110 MFA p0170004, d0180024 LIST OF EXHIBITS (FCCCERTIFICATION(TRANSMITTERS) - REVISED 9/28/98) APPLICANT: Kenwood Communications Corporation FCC ID: ALH32263110 BY APPLICANT: 1. LETTER OF AUTHORIZATION 2. IDENTIFICATION DRAWINGS, 2.1033(c)(11) xLABEL xLOCATION OF LABEL xCOMPLIANCE STATEMENT xLOCATION OF COMPLIANCE STATEMENT 3. PHOTOGRAPHS, 2.1033(c)(12) x 4. DOCUMENTATION: 2.1033(c) (3) USER MANUAL x (9) TUNE UP INFO x (10) SCHEMATIC DIAGRAM x (10) CIRCUIT DESCRIPTION x BLOCK DIAGRAM x PARTS LIST x ACTIVE DEVICES x 5. PART 90.203(e) & (g) ATTESTATION x BY M.F.A. INC. A. TESTIMONIAL & STATEMENT OF CERTIFICATION B. STATEMENT OF QUALIFICATIONS FCC ID: ALH32263110 MFA p0170004, d0180024 TRANSMITTER CERTIFICATION of FCC ID: ALH32263110 MODEL: TK-3140-1 to FEDERAL COMMUNICATIONS COMMISSION Rule Part(s) 22, 74, 90, 95 DATE OF REPORT: August 8, 2001 ON THE BEHALF OF THE APPLICANT: Kenwood Communications Corporation AT THE REQUEST OF : P.O. 41640 Kenwood Communications Corporation Technology Park at Johns Creek 3975 Johns Creek Court #300 Suwanee, GA 30024 Attention of: Joel E. Berger, Research & Development [email protected] (678) 474-4722; FAX: -4731 SUPERVISED BY: Morton Flom, P. Eng. FCC ID: ALH32263110 MFA p0170004, d0180024 THE APPLICANT HAS BEEN CAUTIONED AS TO THE FOLLOWING: 15.21 INFORMATION TO USER. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) SPECIAL ACCESSORIES. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. FCC ID: ALH32263110 MFA p0170004, d0180024 TABLE OF CONTENTS RULEDESCRIPTIONPAGE . Test Report 1 2.1033(c) General Information Required 2 2.1033(c)(14) Rule Summary 6 . Standard Test Conditions and Engineering Practices 7 2.1046(a) Carrier Output Power (Conducted) 8 2.1046(a) R. F. Power Output (Radiated) 10 2.1051 Unwanted Emissions (Transmitter Conducted) 12 2.1053(a) Field Strength of Spurious Radiation 16 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 20 90.214 Transient Frequency Behavior 27 2.1047(a) Audio Low Pass Filter (Voice Input) 37 2.1047(a) Audio Frequency Response 40 2.1047(b) Modulation Limiting 42 2.1055(a)(1) Frequency Stability (Temperature Variation) 45 2.1055(b)(1) Frequency Stability (Voltage Variation) 48 2.202(g) Necessary Bandwidth and Emission Bandwidth 49 FCC ID: ALH32263110 MFA p0170004, d0180024 PAGE NO.1of49. Required information per ISO/IEC Guide 25-1990, par…

Text truncated - open the document above for the full version.