ALH32283110UHF FM Transceiver

KENWOOD CORPORATION INSTRUCTION MANUAL THANK YOU! We are grateful you chose KENWOOD KENWOODKENWOOD KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD KENWOODKENWOOD KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS MODELSMODELS MODELS COVERED COVEREDCOVERED COVERED BY BYBY BY THIS THISTHIS THIS MANUAL MANUALMANUAL MANUAL The models listed below are covered by this ．TK-7150: VHF FM Transceiver ． ．． ．TK-8150: UHF FM Transceiver NOTICES TO THE USER WARNING: GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ILLEGAL OPERATION IS PUNISHABLE BY FINE AND /OR INPRISONMENT. REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. SAFETY: It is important that the operator is aware of、and understands、hazards common to the operation of any transceiver. WARNING: EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn off your transceiver while taking on fuel, or while parked in gasoline service stations.Do not carry spare fuelcontainers in the trunk of your vehicle if your transceiver is mounted in the trunk area. INJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. DYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container. PRECAUTIONS Please observe the following precautions to prevent fire, personal injury, and transceiver damage. Do not attempt to configure the transceiver while driving , it is too dangerous. Do not modify the transceiver for any reason. Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. Do not place the transceiver in excessively dusty, humid , or wet areas, nor on unstable surfaces. If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact your KENWOOD KENWOODKENWOOD KENWOOD dealer. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. KENWOOD CORPORATION INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for technical assistance. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD KENWOOD KENWOOD KENWOOD dealer, an authorized KENWOOD KENWOOD KENWOOD KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Supplied Accessories Quantity Item Part Number K Instruction Manual B62-- 1 DC power cable E30-- 1 Fuse F15-- 1 Mounting bracket J29-- 1 Screw Set N99-- 1 PREPARATION PREPARATIONPREPARATION PREPARATION WARNING Various electronic equipment in your vehicle may malfunction if they are not properly protected from radio frequency nergy. which is present while transmitting. Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the dealer for that make of vehicle and enlist their aid in determining if the equipment will perform while transmitting. KENWOOD CORPORATION Note NoteNote Note: The following preparation instructions are for use by your KENWOO KENWOOKENWOO KENWOOD DD D dealer, an authorized KENWOOD KENWOODKENWOOD KENWOOD servise facility, or the factory. TOOLS REQUIRED Note NoteNote Note: Before installing the transceiver, always check how far the mounting screws will extend below the mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring or parts. The following tools are required for installing the transceiver: ・ 6mm (1/4 inch) or larger electriic drill ・ 4.2mm (5/32 inch) drill bit for the self-tapping screws ・ Circle cutters POWER CABLE CONNECTION CAUTION The transceiver operates in 12V negative ground systems only! Check the battery polarity and voltage of the…

Text truncated - open the document above for the full version.

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Reference: This equipment meets the requirements of FCC Rules, Parts 90.203(e) and (g) as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel. E. Berger Staff Engineer Kenwood Communications Corporation Research & Development Department Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

TK-7150/8150 BLOCK DIAGRAM TK-7150/8150 BLOCK DIAGRAM TK-7150/8150 BLOCK DIAGRAM TK-7150/8150 BLOCK DIAGRAM INT.ANT FB P-DET PC TV APC MA4PH633 RF AMP 2SC3357 Mixer 2SK508NV(K52)*4 Local AMP 2SC3357 IF AMP 2SC3357 HVC131 TA75W01FU 2SK2596 Local AMP * UHF Only 1SV228 V:RD70HVF1U:RD60HUF1 V:PD55003SU:PD55008S V:12.0dBPout=48.5dBmId φ =1.5A U:8.0dBPout=48dBmId φ =4.0A 50 Ω V:19.0dB Id φ =150mA 36dBmU:17.0dB Id φ =400mA 40dBm V:17.0dBmU:23.0dBm V:17.0dBmU:23.0dBm 50 Ω 50 Ω V:10.0dB Id φ =10mA 10dBm ± 2dB U:7.0dB Id φ =5mA 7dBm ± 2dB 50 Ω BATT TA31136FN DET AMP 12CL EXT MIC MI1 Mic Sens TC75W51FU 2SA1586(Y,GR)2SC4116(Y) SB AVR 8V 8R 8T PROTECTPROTECT POW SW 8C +B SB 8CL AVR 5V AVR3.3VAVR3.3VAVR1.8V SWSW 8TC 8RC 5C 3.3A3.3D1.8D AVR 9V AVR Voltage Dobuler 4.9152MHz MI2 DSA3A1-FK ZSA5A27 2SJ506 TA7805F XC62FP3302P XC62FP3302PXC62FP1802P MB PLL 16.8MHz 5C UL MO VCOVCO INV SW SW SW SW TCXO 8CLSTR8CL STR FM IC DAN235E DAN235E 2SC5108(Y) 2SC4116(GR)*3 2SC4116(GR) 2SC4116(GR) 2SC5108(Y) Buff AMP Front AMP RF AMP 2SK508NV(K52) 1SV282*4 DAC MO MB FC SP AM AF AMP TDA8561Q M62364FP TA75W01FUTA75W01FU LMC7101BIM5 AFO SIDE TONE BU4053BCFV DISPLAY AVR RH5VL42 BUSY LED KEY * 6 DMHK/RXDPTT/TXD RST RXD TXD IC904μー Com M30620M8A-***GP 12MHz SW KEY BackLight SW 8.5V TX LED SW 8.5V 5V RESET VOL IRS ES1 POWER SW PS BLC TX RSSI W/N RS232 DRIVER TXD2,RXD2TXD3,RXD3 SCR CODEC AK4550VT 320VC5402PGE μー Com ADM202EARN DSP M30622M4A-***GP PROTECT AVR 5V Voltage DETECTOR SW IGN SENS 02DZ18(X..Y) DTC114EE TA7805F PST9140NR SW Voltage DETECTOR PST9140NR TC4013BF(N) PS INT IGN RST 5C RIPPLE FILTER RIPPLE FILTER TA7805S 2SB1132(Q.R)2SB1132(Q.R) 2SC4116GR 2SC4116GR AN8009M 2SA1832(GR)2SC4738(GR) 2SC4116(GR)02DZ12(Y) 2SK1215(E) ADF4111BRU 12CL 8CL 5C 3m Ω /1W +B Fin=0dBm ± 5dB Local AMP SW SW 2SC4215 DAN235E DAN235E V:180.85 - 218.85MHz +15dBmU:376.95 - 426.95MHz +18dBm V:44.85MHz -117.0 ～ -118.0dBm U:73.05MHz -117.0 ～ -118.0dBm V:136 - 174MHz -117.0 ～ -118.5dBm U:450 - 500MHz -117.0 ～ -118.5dBm 1A Max1W Max 5C 5MD 1A Max2W Max 1A Max1W Max 0.5A Max0.5W Max0.5A Max0.5W Max0.5A Max0.5W Max 50mA Max0.05W Min 9.4V SW LCD AVR BEAT SHIFT 8.5V DTC114EE DTC114EE DTC114EEDTC114EEDTC114EE 5V, 8.5V ENC 2SK1824 BU4053BCFV 2SJ243 TA7805F 2SD1760 02CZ9.1(X,Y) 5V VOL 8.5V VDD DMHK/RXDPTT/TXD INT.SP BLC BLC3BLC4 PF1 ～ PF6 BUSY LEDK CL,CE, DI,DO EN1EN2 SFT SCRANI INV 5C ANI PWADPWDA Power Down 19.2k 614k 4.9152M DATA 1.8D3.3D SCLK LRCK MCLK 19.2k 614K 4.9152M SDTI SDTO SUM BCLKRO , BDXOBFSRO , BDRO 19.2k XF 614k BCLKR1 4.9152M HD0 ～ HD7 HRW,HBILHCNTLOHCNTLI INTO RS HCS Flash ROM AT29C040A-12TI A0 ～ A3 A4 ～ A18 CE,OE,WE D0 ～ D7 Interface Interface SCL SDA EEPROM AT24128N10SI27 DIR D0 ～ D7 3.3D 5MD 5C3.3D 5MD 5C 5C DTC144EE MA2S111 TC7WH32FK * 3 TC74LVX4245FS 5MD INV 12.288MHz 3.3D TXD RXD BEAT SHIFT 12.288MHz RST SBC INT IGN 5C 5C 5C AI1 ～ AI4 AUX(ANI),MCM(ANI)TCNT(ANI),KEY(ANI)DT,CK,EP,CP,OELD,STB1,STB28RC,8TCW/N,AMPDET,CDETTEMP1,TEMP2ASQ,RSSI,UL 5C SCR SCRAFO DI DI ES1ES2 OS1OS2 2SD1757K BU4053BCFV 8C 5C VDD VRef PC TV 5C (ANI) MCO RST 5C DT,CK,LD DT CK,OE STB1 MI2,DI SP,HR AO1 ～ AO4 BU4094BCFV 5C SHIFT RESISTER SHIFT RESISTER 5C BU4094BCFV DTCK STB2 PTO,EMG BUSY,AC BC1 ～ 4 GND GNDAFO HR1 SB 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RXD3 TXD3TXD2RXD2AI2AI4GND AO2 GNDMI2 DI AO3 25 24 23 22 21 20 19 18 17 16 15 ME AI3HR2AO4 AI1 AO1 DEO TXS ACC D-Sub 25pin Surge Protect SW Surge Protect AI1 ～ AI4 DA204U DA204U DTD114EK AO1 ～ AO4 TXD2,RXD2TXD3,RXD3 AFO DEO MI2 DI ME SB HR2HR1 GND HR IRS ES1 ACC 6pin IRS ES1ES2 OS1OS2 IGN 2SC5108(Y) 8C 12 ～ 13dB 2SC3356 0.1A Max0.35W Min3A Max1W Min 5C 3.3A 15mA Max 8C 5C8C SB SFT 2SK1824 50mA/1uAMax35mA Typ 40mA Max0.1mA 3mA/18uA Max 35in40mA V -121.5 ～ -122.0dBm U -120.0 ～ -120.5dBm VHF -118.0 ～ -120.0dBm UHF -118.5 ～ -120.5dBm V -111.5 ～ -113.0dBm U -114.5 ～ -115.0dBm IGN POF D101D1 D102,Q101 IC105 IC101 R827 Q710 IC103 IC102 Q103 IC104 Q517 IC105 IC106 Q106 IC108 Q107 IC107 IC109 Q508,D512 Q511 Q502 Q505,Q506 Q902 Q901 IC901 IC902 Q903,D907 Q905Q906 Q907 Q904,Q908 ATT IC714 Q707,Q708 MA742 D711,D712 R798 TC75W51FU IC719 IC717 5C AVR IC718 IC719 IC715 TC75W51FU NJM78L05UA IC715 IC715 IC721 TA75S01F IC722 Q711 IC717 IC720 5C V:D209 U:D211,D212 1SV279 V:D208 V:D207 1SV228 1SV228 U:D209,D210 U:D207,D208 1SV279 1SV279 SW IC724 TC7S66FU 5C V:Q213 U:Q214 V:Q209 ～ Q212 U:Q210 ～ Q213 Q208 V:Q208 UQ209 V:D513,D514U:D509,D510 Q207 5C W/N W/N D206 D205 Q206 D203 D204 W/N W/N IC201 Q201,Q202 DTC114EE DET SQL Q204 2SC4617(S) MA742 D202 IC713 8R 8R 8R 8R 8R Noise AMP IC501 Q513 Q515 Q516 Q514 DTC114EE Q501,Q503,Q504 V:Q512,U:Q510V:Q512,U:Q510V:Q509,D502,504,507,508 U:Q508,D502,504 2SK508NV(K52) 1SV282*2 V:Q507,D501,503,505,506,D5112SK508NV(K52) 1SV282*4 1SV278 U:Q507,D501,503,505,D5062SK508NV(K52) 1SV282*2 1SV278 V:R16,U:R20 ATT Q1 Q2 Q3 * UHF Only V:2SC3356(R24)U:2SC5110(O) V:2SC3357U:2SC3356(R24) Q4 Q5 IC2 D3 V:7.0dB Id φ =15mA 17dBmU:8.0dB Id φ =10mA 15dBm 8T 8T 8T TEMP2 DET D718MA742 * VHF Only J700 D703,705,706,709Q703,704,705,706 D701,702,707,708 TXS 16 CN704 K700 S76-0434-05 IC701 POF PTO Q700 IC707,708,709 IC705 IC706 IC704 IC703 Q702 D704 INV IC711 TC7SU04FU IC710 IC717 5C Q709 DTC144EE U:8.0dB Id φ =30mA 23dBm IC702 IC700 ::: R781 SW 8TC DTC114EE Q716

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter will authorize the appointment of MORTON FLOM, P. Eng. and/or M. Flom Associates, Inc. to act as our agent in all FCC matters. This appointment is effective until you are otherwise notified by us. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The application is not subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 USC 8.62, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel E. Berger Staff Engineer Research & Development Department Kenwood Communications Corporation Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

FCC ID:ALH32283110 Model Name:TK-8150 Bottom View

FCC ID:ALH32283110 Model Name:TK-8150 Front View

FCC ID:ALH32283110 Model Name:TK-8150 Left View

FCC ID:ALH32283110 Model Name:TK-8150 Model Name Plate

FCC ID:ALH32283110 Model Name:TK-8150 Rear View

FCC ID:ALH32283110 Model Name:TK-8150 Right View

FCC ID:ALH32283110 Model Name:TK-8150 Top View

FCC ID:ALH32283110 Model Name:TK-8150 PC Board Bottom View

FCC ID:ALH32283110 Model Name:TK-8150 PC Board Top View

FCC ID:ALH32283110 1 TK-8150 Circuit Description The Kenwood model TK-8150 is an all solid-state frequency synthesized UHF/FM transceiver designed for operation in the frequency range of 450 MHz to 500 MHz. This model has maximum 128 channels. The unit consists of a TX-RX unit and Display unit and its transmitter is rated for 45W output power. 1. TX-RX Unit The TX-RX unit consists of phase-locked loop (PLL) frequency synthesizer, receiver, transmitter, and control circuit. 1.1 PLL Frequency Synthesizer The transmit signal and the receiver first L.O. signal are generated by the PLL digital frequency synthesizer. The frequency synthesizer consists of a transmitter voltage controlled oscillator (TX VCO: Q507), a receiver voltage controlled oscillator (RX VCO: Q508), a buffer amplifier (Q513 and Q515), an RF amplifier (Q516), a low-pass filter (Q501, Q503 and Q504), a PLL IC (IC501), and TX VCO / RX VCO switches (Q510 and Q511). In the transmit signal mode, an operating frequency programming data is sent to IC501, from the CPU (IC701), to set the programmable counter within IC501. Q510 is turned on to activate the TX VCO and the output signal of the TX VCO is amplified by Q513 and Q516. The signal is then divided down in frequency, at the programmable counter in IC501, to 5.0kHz or 6.25kHz which is compared in phase with a 5.0kHz or 6.25kHz reference signal, derived from 16.8MHz VCXO (X501) and a 1/3360 or a 1/2688 fixed counter in IC501, at the phase comparator in IC501. The VCXO operates at 16.8MHz and its frequency stability is maintained within 2.5ppm (temperature range of –30 to +60 degrees). The phase comparator output signal is fed into a low-pass filter (Q501, Q503 and Q504) before being applied to the TX VCO as a frequency control voltage. If an unlock condition occurs in the phase locked loop, this condition is detected by Q518 and Q519. This cause the transmitter 8V supply cut off, resulting in the prevention of an unauthorized transmission. The transmitter modulation signals (processed Mic. audio and sub-audible signaling) are applied to the TX VCO for frequency modulation. In the receive mode, the VCO is substituted with Q508 (RX VCO) and it generates the receiver first local oscillator signal according to the data sent from the CPU (IC701). The basic operation of the synthesizer remains the same. 1.2 Receiver Circuit The receiver is double conversion super-heterodyne, designed to operate in the frequency range of 450MHz to 500MHz. The receiver circuit consists of front-end circuit, First Mixer, IF amplifier circuit, audio amplifier circuit, and squelch circuit. FCC ID:ALH32283110 2 The front-end circuit consists of former BPF(D211, D212), RF amplifier Q214, and latter BPF (D207-D210). The BPF covers frequency ranges 450 to 500MHz. The latter BPF(D207-D210) attenuates the unwanted signals, and sends only the necessary signal to the first mixer. The signal from the BPF is heterodyned with the first local oscillator signal from the PLL frequency synthesizer circuit at the first mixer DBM (Q210,211,212,213) to become a 73.05MHz first intermediate frequency (IF) signal. The first IF signal is fed through two monolithic crystal filters (XF201: Wide, XF202: Narrow) to further remove spurious signals. The first IF signal is amplified by Q207 and Q206, and then enters IC201 (FM system IC). The signal is heterodyned again with a second local oscillator signal (73.505MHz) with in IC201 to become a 455kHz second IF signal. The second IF signal is fed through a 455kHz ceramic filters (CF201,203: Wide, CF202,204: Narrow) to further eliminate unwanted signal, and the quadrature detection circuit FM-detects the signal to produce a base-band signal and output it from pin 9. The recovered audio signal obtained from IC201 is amplified and anti-aliasing filtered by IC712(A/2), inputted to the AINR terminal of CODEC IC (IC713), and audio processed by DSP (IC710). The processed audio signal from AOUTR terminal of IC713 is amplified and filtered by IC716 (A/2) to a sufficient level. The audio signal goes to an electronic volume (IC718), to the input of multiplexer IC (IC717), and is amplified to drive a loudspeaker by an audio power amplifier (IC720). The 12W audio output can be provided to external 4 ohms speaker through the 6-pin ACC connector “ES1,ES2” on the rear panel. The output signal from IC201 enters FM IC again, then passed through a band-pass filter. The noise component output from IC201 is amplified by Q204 and rectified by D202 to produce a DC Voltage corresponding to the noise level. The DC voltage is sent to the analog port of the CPU (IC701). And IC201 outputs a DC voltage(RSSI) corresponding to the input of the IF amplifier. 1.3 Transmitter Circuit The transmitter circuit consists of Microphone circuit, Modulation level adjustment circuit, Driver and Final power amplifier circuit, and Automatic power control circuit. The signal from the microphone is passed through AGC circuit (Q707, Q708 and D711, D712 and IC714 A/2) so that it dose not saturates. The AGC is operated by controlling the + and side levels of amplitude using the current obtained by positive and negative detection of the amplified audio signal. The audio signal is amplified by IC712 B/2, inputted to the AINL terminal of CODEC IC (IC713), and audio processed by DSP (IC710). The processed audio signal from the AOUTL terminal of IC713 is filtered by IC716 (B/2), and amplified by the summing amplifier IC719 (B/2). The output of the summing amplifier IC719 (B/2) is passed to an electronic volume (IC718) for maximum deviation adjustment before being applied to a varactor diode in the voltage controlled oscillator (VCO). The transmit signal is generated by the TX VCO, and amplified by Q515, and sent to Driver and Final power amplifier circuit. This amplified signal is amplified by Driver circuit consists of Q1, Q2, Q3 and Q4. And this signal is passed to the FINAL stage. The RF power amplifier consists of MOS FET transistor (Q…

Text truncated - open the document above for the full version.

FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 FOR MODEL: TK-8150 (K) FCC ID:ALH32283110FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 <X57-6580-10> TXRX UNIT <X57-6580-10> TXRX UNIT<X57-6580-10> TXRX UNIT <X57-6580-10> TXRX UNIT CIRCUIT CIRCUITCIRCUIT CIRCUIT SYMBOL SYMBOLSYMBOL SYMBOL PART NUMBER PART NUMBERPART NUMBER PART NUMBERDESCRIPTION DESCRIPTIONDESCRIPTION DESCRIPTION D1ZSA5A27ZENER DIODE, SURGE PROTECTOR D202DZ6.2(Y)ZENER DIODE, VOLTAGE PROTECTION D3MA4PH633DIODE, ANT SWITCH D4XB15A709DIODE, ANT SWITCH D5, 6MA742DIODE RF DETECTOR D9XB15A709DIODE,ANT SWITCH D511SS355DIODETEMPERATURE COMPENSATION D101DSA3A1-FKDIODE, PROTECTION OF REVERSE CONNECTION D10202DZ18(X,Y)ZENER DIODEVOLTAGE REFERENCE D10302DZ15(X,Y)ZENER DIODEVOLTAGE REFERENCE D104－106 1SS355DIODEDC SWITCH D108DA204UDIODESURGE PROTECTOR D10902DZ15(X,Y)ZENER DIODEVOLTAGE REFERENCE D2011SS355DIODEDC SWITCH D202MA742DIODENOISE DETECTION D203-206 DAN235EDIODEWIDE/NARROW SWITCH D207－212 1SV279VARICAPBPF TUNING D501－504 1SV282VARICAPFREQUENCY CONTROL D5051SS388DIODEVOLTAGE DOUBLER D5061SV278VARICAPMODULATOR D5071SS388DIODEVOLTAGE DOUBLER D50802DZ12(Y)ZENER DIODEVOLTAGE REFERENCE D509、510 HVC131DIODERF SWITCH D515MA2S111DIODEDC SWITCH D7001SS355DIODESURGE PROTECTOR D701-703 DA204UDIODESURGE PROTECTOR D704MA2S111DIODEVOLTAGE REDUCTION D705-709 DA204UDIODESURGE PROTECTOR D71002DZ18(X,Y)ZENER DIODESURGE PROTECTOR D711、712 MA742DIODEAF DETECTOR D7141SS388DIODEDC SWITCH D715, 716 02DZ18(X,Y)ZENER DIODESURGE PROTECTOR D717、718 02DZ5.1(Y)ZENER DIODESURGE PROTECTOR D785－788 02DZ5.1(Y)ZENER DIODESURGE PROTECTOR D789MINISMDM075/24 VARISTORCURRENT PROTECTOR D790、791 MINISMDM110/16 VARISTORCURRENT PROTECTOR IC1、2TA75W01FUIC, DC AMP IC101PST9140NRIC, VOLTAGE DETECTOR IC102TC4013BF(N)IC, D Flip-Flop IC103PST9140NRIC, VOLTAGE DETECTOR IC104TA7808SIC, VOLTAGE REGULATOR IC105TA7805FIC, VOLTAGE REGULATOR IC106XC62FP3302PIC, VOLTAGE REGULATOR IC107XC62FP1802PIC, VOLTAGE REGULATOR IC108XC62FP3302PIC, VOLTAGE REGULATOR IC109AN8009MIC, VOLTAGE REGULATOR IC201TA31136FNIC, FM IF SYSTEM IC202TC7S66FUIC, MULTIPLEXER IC501ADF4111BRUIC, PLL IC700BU4094BCFVIC, SHIFT RESISTER IC701M30624FGAGPIC, CPU IC702BU4094BCFVIC, SHIFT RESISTER IC703ADM202EARNIC, RS232C TRANCEIVER IC704AT24128N10SI27 IC, EEP ROM IC705AT29C040A-12TI IC,FLASH ROM IC706TC74LVX4245FS IC, BUS TRANSCEIVER IC707－9 TC7WH32FKIC, OR GATE IC710320VC5402PGEIC, DSP IC711TC7SU04FUIC, INVERTER IC712TA75W01FUIC, AF AMP IC713AK4550VTIC, CODEC IC714TC75W51FUIC, MIC AMP/AGC IC715TA75W01FUIC, BUFFER AMP IC716TA75W01FUIC, ANTI-ALIASING FILTER IC717BU4053BCFVIC, MULTIPLEXER IC718M62364FPIC, D/A CONVERTER IC719TC75W51FUIC, AF AMP IC720TDA8561QIC, AUDIO POWER AMP IC721LMC7101BIM5IC, DC AMP IC722TA75S01FIC, AF AMP IC723NJM78L05UAIC, VOLTAGE REGULATOR IC724TC7S66FUIC, MULTIPLEXER Q12SC5110(O)TRANSISTORRF AMP Q22SC3356(R24)TRANSISTORRF AMP Q32SK2596FETRF AMP Q4PD55008STRANSISTOR DRIVE AMP Q5RD60HUF1TRANSISTORFINAL AMP Q101DTC114EETRANSISTORDC SWITCH Q102DTC114EETRANSISTORSWITCH Q1032SJ506(S)FETDC SWITCH Q104DTC114EETRANSISTORDC SWITCH Q105DTC114EETRANSISTORDC SWITCH Q1062SB1132(Q,R)TRANSISTORDC SWITCH Q1072SB1132(Q,R)TRANSISTORDC SWITCH Q108DTA114EETRANSISTORDC SWITCH Q109DTA114YETRANSISTORDC SWITCH Q110DTC114TETRANSISTORDC SWITCH Q111DTA114EETRANSISTORDC SWITCH Q112DTA114YETRANSISTORDC SWITCH Q113DTC114YETRANSISTORDC SWITCH Q201DTC114EETRANSISTORW/N SWITCH Q202DTA114EETRANSISTORW/N SWITCH Q203DTC114EETRANSISTORW/N SWITCH Q2042SC4617(S)TRANSISTORNOISE AMP Q205DTA144EETRANSISTORW/N SWITCH Q2062SC4215(Y)TRANSISTORIF AMP Q2072SC3357TRANSISTORPRE IF AMP Q2082SC3356TRANSISTORRF AMP Q2092SC3357TRANSISTORRF AMP Q2102SK508NV(K52)FETMIXER Q2112SK508NV(K52)FETMIXER Q2122SK508NV(K52)FETMIXER Q2132SK508NV(K52)FETMIXER Q2142SC3357TRANSISTORRF AMP Q5012SC4116(GR)TRANSISTORACTIVE FILTER Q5022SK1215(E)FETOSCILLATOR Q5032SC4116(GR)TRANSISTORACTIVE FILTER Q5042SC4116(GR)TRANSISTORACTIVE FILTER Q5052SA1832(GR)TRANSISTORDC SWITCH Q5062SC4738(GR)TRANSISTORDC SWITCH Q5072SK508NV(K52)FETRX OSCILLATOR Q5082SK508NV(K52)FETTX OSCILLATOR Q5092SC4116(GR)TRANSISTORAVR Q5102SC4116(GR)TRANSISTORTX/RX SW Q5112SC4116(GR)TRANSISTORTX/RX SW Q5122SC4116(GR)TRANSISTORRIPPLE FILTER Q5132SC5108(Y)TRANSISTORBUFFER AMP Q514DTC114EETRANSISTORINVERTER Q5152SC5108(Y)TRANSISTORBUFFER AMP Q5162SC5108(Y)TRANSISTORAMP Q5172SC4116(GR)TRANSISTORRIPPLE FILTER Q5182SA1832(GR)TRANSISTORDC SWITCH Q519DTC144EETRANSISTORDC SWITCH Q5202SC4116(GR)TRANSISTORDC SWITCH Q521DTC114EETRANSISTORINVERTER Q7002SK1824FETDC SWITCH Q701DTC114EETRANSISTORDC SWITCH Q702DTC144EETRANSISTORDC SWITCH Q703DTD114EKTRANSISTORDC SWITCH Q704DTD114EKTRANSISTORDC SWITCH Q705DTD114EKTRANSISTORDC SWITCH Q706DTD114EKTRANSISTORDC SWITCH Q7072SC4116(Y)TRANSISTORMIC GAIN SWITCH Q7082SA1586(Y,GR)TRANSISTORMIC GAIN SWITCH Q709DTC144EETRANSISTORINVERTER Q710DTC114EETRANSISTORDC SWITCH Q7112SD1757KTRANSISTORDC SWITCH Q7122SJ243FETDC SWITCH Q7132SK1824FETDC SWITCH Q714DTC144EETRANSISTORDC SWITCH Q716DTC114EETRANSISTORDC SWITCH Q719DTC114YETRANSISTORDC SWITCH Q720DTC114YETRANSISTORDC SWITCH FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 FOR MODEL: TK-8150 (K) FCC ID:ALH32283110FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 FOR MODEL: TK-8150 (K) FCC ID:ALH32283110 <X54-340> DISPLAY UNIT <X54-340> DISPLAY UNIT<X54-340> DISPLAY UNIT <X54-340> DISPLAY UNIT CIRCUIT CIRCUITCIRCUIT CIRCUIT SYMBOL SYMBOLSYMBOL SYMBOL PART NUMBER PART NUMBERPART NUMBER PART NUMBERDESCRIPTION DESCRIPTIONDESCRIPTION DESCRIPTION D902DA204UDIODE, SURGE PROTECTOR D903DA204UDIODE, SURGE PROTECTOR D904DA204UDIODE, SURGE PROTECTOR D905DA204UDIODE, SURGE PROTECTOR D906DA204UDIODE, SURGE PROTECTOR D90702CZ9.1(X,Y)ZENER DIODE, VOLTAGE REFERENCE D908B30-2050-05LED,KEY backlight D909B30-2050-05LED, KEY backlight D910B30-2050-05LED, KEY backlight D911B30-2050-05LED, KEY backlight D912B30-2193-05LED, TX light D913B30-2050-05LED, KEY backlight D914B30-2050-05LED, KEY backlight D915B30-2194-05LED, RX light D91602DZ18(X,Y)ZEN…

Text truncated - open the document above for the full version.

TK-8150FCC ID:32283110 K PARTNOPROCESS '0-10 UNIT PART NAME(E) Z83-3152-03X1 INTERCONNECTION DIAGRAM X54-3400-1011 DISPLAY UNIT X57-6580-1011 TX-RX UNIT A01-2185-0211 CABINET A10-4059-0111 CHASSIS A62-1037-0311 PANEL ASS'Y A62-1038-0111 MAIN PANEL B10-2732-0411 FRONT GLASS B11-1296-0411 ILLUMINATION GUIDE B43-1138-0411 BADGE G10-1289-0411 FIBROUS SHEET G13-1932-0411 CUSHION B11-1297-0411 FILTER B41-1837-0411 CAUTION LABEL B42-5650-0411 S/NO. LABEL B44-2163-0411 UPC CODE LABEL B44-2165-040.25 UPC CODE LABEL B59-1653-0011 PAMPHLET B59-2298-0011 PAMPHLET B62-1619-0011 INSTRUCTION MANUAL B72-2087-0411 MODEL NAME PLATE E04-0167-0511 RF COAXIAL PECEPTACLE(M) E30-3478-0511 DC CORD ASS'Y E37-1002-0511 LEAD WIRE WITH CONNECTOR E37-1003-0511 LEAD WIRE WITH CONNECTOR E37-1004-0511 LEAD WIRE WITH CONNECTOR E37-1006-0511 LEAD WIRE WITH CONNECTOR E37-1031-0511 LEAD WIRE WITH CONNECTOR F05-1537-0531 FUSE(BLADE) F09-0445-0511 CAP F10-2442-0211 SHIELDING COVER F29-0478-0511 INSULATING COVER G02-0861-0411 FLAT SPRING G02-0894-0411 EARTH SPRING G02-0896-0411 FLAT SPRING G53-1551-0211 PACKING G53-1552-0311 PACKING G53-1554-0311 PACKING G53-1555-0421 PACKING H02-0616-0311 INNER PACKING CASE H12-3124-0211 PACKING FIXTURE H12-3125-0211 PACKING FIXTURE H12-3141-0321 PACKING FIXTURE H25-0029-0421 PROTECTION BAG H25-0720-0411 PROTECTION BAG H25-2343-0411 PROTECTION BAG H25-2352-0411 PROTECTION BAG H52-1921-0211 ITEM CARTON CASE H62-1663-030.25 OUTER PACKING CASE J19-1584-0511 HOLDER J21-8436-0411 HARDWARE FIXTURE J21-8437-0411 HARDWARE FIXTURE J21-8445-0411 HARDWARE FIXTURE J29-0697-0311 BRACKET J61-0307-0511 BAND K29-9221-0321 KNOB K29-9222-0211 KEY TOP N09-2409-0521 HEXAGON HEAD SCREW N10-2070-4611 HEXAGON NUT N87-2606-46141 BRAZIER HEAD TAPTITE SCREW N87-2620-4691 BRAZIER HEAD TAPTITE SCREW N87-3008-4561 BRAZIER HEAD TAPTITE SCREW N99-2033-0511 SCREW SET T07-0738-0511 SPEAKER T91-0621-0511 MICROPHONE RD60HUF1-0111 FET N67-3008-4621 PAN HEAD SEMS SCREW W PD55008S11 FET

-t D B A D B D B A D D D D D D B D D D B D D D D D B B D D D DD B -t -t B B B 1 DATE ISSUED REVISION NO 32 USE FOR 415 SYMBOL 2 3 4 5 6 7 8 9 1011 121314 15 16 ABCDEFGHIJ 679 8 PART NUMBER DESIGNED PART NAME DRAWN CHECKED APPROVED ------------------ HD4 TD1 HD1 AO4 A6 BFSR0 HD3 TRST LD TXD3 A7 TMS CK HD1 A12 HD2 TCK HD3 AO1 A15 TXD2 A16 RXD3 BDXO RXD2 A18 XF HD5 WE RXD HD0 HR1 A17 STON STON AI2 HD2 AM HD7 TXD A14 AI4 AO3 HD5 A13 AI3 AO2 A8 AI2 HD4 AO1 A9 TXD HD6 AI1 AI3 EMU0 A11 TXD2 BFSR0 BCLKR0 EMU1 CP A3A2 TD0 AI1 A1 BDXO A8 1.8D 1.8D 1.8D 1.8D DT TD1 A0 BDRO D0 RXD HD7 D1 HD6 TRST D5D2 XF TCK RXD2 D6OED3 TMS D7 BDRO D4 AI4 AO4 CE BCLKR0 EMU1 BCLKR1 A10 AO3 EMU0 HD0 AO2 A4 TD0 EP A5 MO MO EP DT CP BCLKR1 BCLKR1 BCLKR1 MIC IGN D7 D6 D5 D4 D3 D2 D1 D0 A0A1A2A3A4A5A6A7A9 A10A11A12A13A14A15A16A17A18 WEOECE 3.3A 1.8 1.8 3.3 TXO TXO TXO TXI TXI TXI LD TEMP2 TEMP1 DEO UL AM IGN CDET CDET RST TXD3 RXD3 +B +B 3.3D 3.3D 3.3D 3.3D 3.3D 3.3D 5MD 5MD 5MD DTCK 9C 8C 8C 8C DI PSW RXO RXO 5C 5C 5C 5C 5C 5C 5C RXI RXI RXI HR2 MI2 SB SB R110 4.7k C132 1000p C116 0.1u R104330k C113 0.1u C102 0.047u C122 0.1u C114 470p C120 0.047u R109 47k 2SB1132(Q,R) Q107 R107 47k C133 4.7u16 C126 100p R101 470k D101 DSA3A1-FK R108 47k C115 0.047u C121 1000p C124 100p R111 2.2k 2SJ506(S) Q103 C104 100p C119 1u C131 10u 10 C109 470p C127 4.7u16 2SB1132(Q,R) Q106 C123 0.1u C107 470p R102 390k R105 330k C110 470p R106 4.7k C125 100p C118 1u C130 10u 10 C103 470p C128 10u 10 R103 470 C129 10u 10 C117 1u C111 0.1u R281 2.7k D212 1SV279 R262 10 R529 220k $R283 R48 100k L202 470n R216 22k $C67 C81 2p R203 100k L3 18n R17 0 C248 470p C565 6p R2063.3k C43 470p $C310 L519 18n R3 2.2k C270 33p L4 10n C507 0.1u R551 47 C558 0.01u R213 27k $C234 C515 0.1u R282 3.9k C550 5p D503 1SV282 R283 100k R11 470 L504 100u 2SK1215(E) Q502 R227 47k C542 0.5p C204 1000p C505 470p C21 470p R12 22 C264 0.01u C561 47u 20 R532 220 R548 220 C564 0.01u C250 0.01u 2SK508NV(K52) Q212 $C70 $C268 $C75 C559 1000p R504 1.2k $C56 R47 100k C45470p R506 10 D209 1SV279 C214 0.1u R538 0 CN202 1 2 2SC4738(GR) Q506 C572 470p R527 68k D3 MA4PH633 L1 10n R13 22 R528 12k R252 22 2SC4116(GR) Q509 VR1 47k R265 10 R207 56 C242 0.01u 2SC4215(Y) Q206 C35 470p IC201 TA31136FN 1OSCIN 2OSCOUT 3MIXOUT 4VCC 5IFIN 6DEC 7FILOUT 8FILIN 9 AFOUT 10 QUAD 11 IFOUT 12 RSSI 13 N-DET 14 N-REC 15 GND 16 MIXIN L2 10n C18 470p C257 9p R214 15k C213 27…

Text truncated - open the document above for the full version.