ALH32943220UHF FM Transceiver

TK-7102H INSTRUCTION MANUAL VHF FM TRANSCEIVER © B62-1596-00 (M) 09 08 07 06 05 04 03 02 01 00 KENWOOD CORPORATION TK-8102H UHF FM TRANSCEIVER i THANK YOU! We are grateful you chose KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: •TK-7102H:VHF FM Transceiver •TK-8102H:UHF FM Transceiver NOTICES TO THE USER uGovernment law prohibits the operation of unlicensed transmitters within the territories under government control. uIllegal operation is punishable by fine and/or imprisonment. uRefer service to qualified technicians only. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. uEXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. uINJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. uDYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container. PRECAUTIONS Please observe the following precautions to prevent fire, personal injury, and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. • Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces. • If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact your KENWOOD dealer. ii CONTENTS UNPACKING AND CHECKING EQUIPMENT ................................... 1 S UPPLIED ACCESSORIES..................................................................... 1 PREPARATION .................................................................................. 2 T OOLS REQUIRED.............................................................................. 2 POWER CABLE CONNECTION............................................................... 2 I NSTALLING THE TRANSCEIVER.............................................................. 3 ORIENTATION .................................................................................... 4 FRONT PANEL................................................................................... 4 DISPLAY............................................................................................ 5 REAR PANEL..................................................................................... 5 BASIC OPERATIONS ........................................................................ 6 S WITCHING POWER ON/ OFF ............................................................. 6 ADJUSTING THE VOLUME..................................................................... 6 SELECTING A CHANNEL....................................................................... 6 TRANSMITTING................................................................................... 6 RECEIVING........................................................................................ 6 SCAN .................................................................................................. 7 T EMPORARY DELETE.......................................................................... 7 REVERT CHANNEL.............................................................................. 7 DTMF CALLS ..................................................................................... 8 MANUAL DIALLING............................................................................. 8 STORING DTMF NUMBERS................................................................. 8 D IALLING STORED DTMF NUMBERS.................................................... 8 CLEARING STORED DTMF NUMBERS................................................... 8 REDIALLING....................................................................................... 8 CODE SQUELCH (ID CODE) ............................................................ 9 R ECEIVING........................................................................................ 9 TRANSMITTING................................................................................... 9 ADVANCED OPERATIONS ............................................................. 10 T IME-OUT TIMER (TOT) .................................................................... 10 BUSY CHANNEL LOCKOUT (BCL) ...................................................... 10 TALK-AROUND................................................................................. 10 MONITOR........................................................................................ 10 E MERGENCY OPERATION................................................................... 11 K EY LOCK...................................................................................... 11 B EGINNING/ END OF TRANSMISSION ID SIGNAL.................................... 11 1 UNPACKING AND CHECKING EQUIPMENT Note: The follo…

Text truncated - open the document above for the full version.

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Reference: This equipment meets the requirements of FCC Rules, Parts 90.203(e) and (g) as applicable. Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel. E. Berger Staff Engineer Kenwood Communications Corporation Research & Development Department Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

1234567891011 HGFEDCBA USE FOR SYMBOL REVISION NO ISSUED DATE 12345 DESIGNED DRAWN CHECKED APPROVED PART NUMBERPART NAME 6789 - - - - - - - - - - - - - - - - - - KENWOODCORPORATION 8R DTC363EU LEDC2 SW PSB BPF TEMP3 VCOMOD Q21 NARROW B NJM78L05UA 3 RF D19 KMI2 FILTER FILTER M62363FP(*/8) Q32 LEDC1 Vg SW KMO2 CONV SBC MUTE3 IGNITION 3SK255 EEPROM SW 5M 4 KMI1 PLL IC IC101 QT/DQT LIPPLE D/A FINAL LEDPF SW DEMODULATOR KMO1 KRC414RTK MIX D/A WIDECM SW INT M LD LA4600 784214AGC125 AMP FILTER 8CL CONV IF KMI4 Q16 LEDMON SW Q14 POW. WIDE P SW SW RESET CK IC6 ANT SW AF KMI3 Q7 D/A RED CM DET CV Q12 NJM2100V PA POWER RESET SW TC7W74FU DT LPF CPU 2SJ243 Q24 CONV AMP BUSY 1SS372 8T INT HOOK(RXD) 16.8MHz KRX102U HOOK SW TXRX IC19 PLLE IF Q37 2SC4617(S) AMP1 D/A 4 IC4 Q11 8C 8T ME SW PTT VCOMOD SW HPF IC1 AMP2 XF1 2SK1824 7.159MHz CONV 2SK3075 2SK508NV(K52) 3 IC3 MIC LEDC4 RF LEDR 2SC3356(R24) 8RC Q22,43 PC MB15A02 PST9140NR Q13 KRC102S DIVIDER Q801 49.95MHz M62363FP(*/8) 2SC4919 8C 2 LEDC3 LEDG Q800 2SK1824 Q39 2SK3478-22 8TC Vg 2SK1824 50.4MHz KRC102S 2SC4738(GR) NJM78L05UA MCF Q41 MICBL 3.579545MHz 1 LEDC4 Q101 2SK2596 8C MUTE2 2SC5110(0) X2 KRC102S Q5 IC14 CONV AGC MA742 IC9 2SC4617(S) PF Q23 8T MUTE1 SW Q20 KRC102S Q4 Q29 D/A 8T MIC/IDC SQIN MON LC73872M BSHIFT IC800 BSHIFT 2SC5108(Y) KRC102S IC3 KRC102S IC21 IC20 DET 2SC1832(GR) KEY DECODE VCO LEDG AF KMO2 TA75W01FU (2) 8T IC22 KRC102S M62363FP(*/8) Q31 NOISE PUMP KIA7808AF Q8 DTMF TX LEDR SPLATTER CHARGE KMO1 MA742 NJM2904V NJM2904V 8R KRC102S D15 CHARGE 2SA1745(6,7) Q33 Q4 DET SW LEDC2 D44 PUMP FILTER LEDC4 D806 DRIVE KRC102S Q7 Q10 D13 8C Q30 VCO KTA1664(Y) LEDC1 OVER VOLTAGE DET IC3 LEDC3 DRIVE MA742 D8 Q3Q5 FILTER Q3 DAN222 KRC102S RX 8V LEDPF AGC PRE MICBL IGNITION M62363FP(*/8) D805 Q6 D7 2SC4649(N,P) Q1 DRIVE 5C 450kHz Q34 AVR LEDMON SW 2SK508NV(K52) DAN222 LEDG Q2 D/A DET BATT.CHECK D6 X54-334*-** MICBL 8RC SW Q42 KRC102S T/R POWER 8CL D43 LOOP LEDR CONV POW. TEMP2 8R D5 KRC102S DISPLAY UNIT RF SW 2SA1641(S,T) MIC TA75W01FU (1) Q15 MUTE LEDC2 CONV 8TC 2SC4649(N,P) TEMP1 PSB D801,D802 MA4PH633 Q10 X57-639*-** (NARROW) HVC350B ME BUFFER MIC BATT. CHECK Q6 LEDC1 AVR 2SC5108(Y) D/A KMO1 24LC08BT-ISN Q9 D803,D804 XB15A709 CF2 TRIPLER TX-RX UNIT HOOK APC MICMT D25,26,28 SBC LEDPF DAN222 BUFF IC3 KRC404RTK KMO2 IC7 MIC KMI2 KRA2555S (WIDE) SW LEDMON PTT CONTROL DTMF TUNE SB Q18 8R M62363FP(*/8) Q38 KMI4 5M KMI1 E D12 CF1 SW GND 2SC2412K SUM TCXOM0D RF BPF SW TK-8102H(K2) BLOCK DIAGRAM BPF BEEP CM DET KMI3 MUTE1 +B D11 NARROW D18 TCXO SW RESET IC4 Q26 IC15 16.8MHz RF BPF DTMF OVER KMI2 NJM2902V(*/4) SP SW D10 5C 8C SW PTT(TXD) INT 3SK255 IC18 5V TUNE NJM2902V(*/4) CK EXT VOLTAGE KMI1 IC11 D9 M62363FP(*/8) DTMF/BEEP Q19 SW PSB LD 8R AVR SP HVC350B BUFF PST9140NR DT SW 1 16.8MHz IC10 IC3 MUTE2 LEDC3 KMI4 2SC4649(N,P) SW MBL ANT RF 5M D21,22 TCXOMOD IC17 PLLE SW 2 5C DAN235E IC3 NJM2902V KMI3 BLOCK DIAGRAM

August 27, 2001 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter will authorize the appointment of MORTON FLOM, P. Eng. and/or M. Flom Associates, Inc. to act as our agent in all FCC matters. This appointment is effective until you are otherwise notified by us. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The application is not subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 USC 8.62, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Kenwood Communications Corporation Joel E. Berger Joel E. Berger Staff Engineer Research & Development Department Kenwood Communications Corporation Corporate Headquarters Kenwood Communications Corporation 3975 Johns Creek Court, Suite 300 Suwanee, GA 30024 678-474-4700 Distribution: 2201 E. Dominguez St. Long Beach, CA 90810 (310) 639-4200 Mailing Address: P.O. Box 22745 Long Beach, CA 90801-5745

FCC ID:ALH32943220 Model Name TK-8102HK2 Front View

FCC ID:ALH32943220 Model Name TK-8102HK2 Bottom View

FCC ID:ALH32943220 Model Name TK-8102HK2 Left View

FCC ID:ALH32943220 Model Name TK-8102HK2 Rear View

FCC ID:ALH32943220 Model Name TK-8102HK2 Right View

FCC ID:ALH32943220 Model Name TK-8102HK2 Top View

FCC ID:ALH32943220 Model Name TK-8102HK2 Bottom View

FCC ID:ALH32943220 Model Name TK-8102HK2 PCB Front

FCC ID:ALH32943220 Model Name TK-8102HK2 PCB Rear

TK-8102H (K2) Specifications 1. General Frequency Range 485 to 512 MHz Number of Channel 4ch Channel Spacing 25 kHz (Wide) / 12.5 kHz (Narrow) Type of Emission 16K0F3E (Wide) / 11K0F3E (Narrow) Power Supply Voltage 13.6V DC Nominal Antenna Impedance 50 Ω Nominal Operating Temperature -30 °C to +60 °C Dimension W. 161 mm × D.160.0 mm H. 43 mm 2. Receiver Conversion Type Double Conversion Super-heterodyne Intermediate Frequencies 1st 49.95 MHz 2nd 450 kHz Sensitivity (12dB SINAD) -118 dBm (Wide) / -116 dBm (Narrow) Spurious & Image Rejections 75 dB Minimum Inter-modulation Rejection 70 dB Min. (Wide) / 60 dB Min. (Narrow) Adjacent Channel Rejection 75 dB Min. (Wide) / 65 dB Min. (Narrow) Hum and Noise 45 dB Min. (Wide) / 40 dB Min. (Narrow) Audio Output Power 4.0 W Minimum (5 % distortion / 8 Ω) Frequency Stability ±2.5 ppm Current Consumption 0.4 A Std-by 1.0 A Operating 3. Transmitter Output Power 25 – 45 W(Variable) Maximum Modulation ±5.0 kHz (Wide) / ±2.5 kHz (Narrow) FM Hum and Noise 45 dB Min. (Wide) / 40 dB Min. (Narrow) Audio Distortion 5% Maximum (Wide) / 5% Maximum (Narrow) Mic Sensitivity 5 mV Nominal Spurious and Harmonics Attenuation 65 dB Minimum Frequency Stability ±2.5 ppm Current Consumption 14.0 A Maximum at 45 W output

FCC ID:ALH32943220 Model Name:TK-8102HK2 FREQUENCY LIST TK-8102HK2 RECEIVETRANSMIT CHANNEL SPACING CH 1485.25MHz 485.25MHz WIDE CH 2498.75MHz 498.75MHz WIDE CH 3511.75MHz 511.75MHz WIDE CH 4498.75MHz 498.75MHz NARROW

TK-8102H(K2) Circuit Descriptions The Kenwood model TK-8102H is an all solid-state frequency synthesized UHF/FM transceiver designed for operation in the frequency range of 485 MHz to 512 MHz. This model has 4 channels. The unit consists of a TX-RX unit and display unit and its transmitter is rated for 45 W output power. 1. TX-RX Unit The TX-RX unit consists of a Voltage Control Oscillator (VCO), a receiver section, a transmitter section, a control section and a power supply section. 1.1 PLL Frequency Synthesizer The transmit signal and the receiver first L. O. signal are generated by the PLL digital frequency synthesizer. The frequency synthesizer consists of a transmitter voltage controlled oscillator (TX VCO, Q11), a receiver voltage controlled oscillator (RX VCO, Q10), a buffer amplifier (Q15), an RF amplifier (Q3), a low-pass filter, a PLL IC (IC1) and TX VCO/RX VCO switches (Q7 and Q12). In the transmit signal mode, an operating frequency programming data is sent to IC1, from the CPU(IC6), to set the programmable counter within IC1. Q7 is turned on to activate the TX VCO and the output signal of the TX VCO is amplified by Q15 and Q3 before it is routed to IC1. The signal is then divided down in frequency, at the programmable counter in IC1, to 5.0kHz or 6.25kHz which is compared in phase with a 5.0kHz or 6.25kHz reference signal, derived from 16.8MHz crystal oscillator and a 1/3360 or a 1/2688 fixed counter in IC1, at the phase comparator in IC1. The crystal oscillator operates at 16.8MHz and its frequency stability is maintained within 2.5ppm (temperature range of –30 to +60°C). The phase comparator output signal is fed into a low-pass filter before being applied to the TX VCO as a frequency control voltage. If an unlock condition occurs in the phase locked loop, this condition is detected by D6. This cause the transmitter 8V supply cut off, resulting in the prevention of an unauthorized transmission. The transmitter modulation signals (processed Mic. audio and sub-audible signaling) are applied to the TX VCO for frequency modulation. In the receive mode, the VCO is substituted with Q10 (RX VCO) and it generates the receiver first local oscillator signal according to the data sent from the CPU(IC6). The basic operation of the synthesizer remains the same. 1.2 Receiver Circuit The receiver is a double conversion super-heterodyne, designed to operate in the frequency range of 485 MHz to 512 MHz . The receiver RF and IF sections consist of an RF amplifier (Q26), a first mixer (Q21), and an FM IF IC (IC5). An incoming RF signal from the antenna is fed into a band-pass filter which consists of L36, L38, L49, varactor diodes (D25, D26, D28) and variable capacitors (TC3 and TC5) after going through an antenna switch in the transmitter power amplifier section. TC3 and TC5 will be tuned manually with D25, D26 and D28 tuned electrically by TV voltage for the best BPF response. This RF signal is then amplified by an RF amplifier (Q26) and filtered again by band-pass filters (L30, L32 and D21, D22). After amplification and filtering, the signal is applied to the first mixer (Q21) for mixing with the first local oscillator signal generated by the frequency synthesizer. The heterodyning action of the first mixer produces a 49.950MHz intermediate frequency (first IF), which is applied into two monolithic crystal filters. The signal out of the crystal filters is amplified by a first IF amplifier (Q19) and is sent to the FM IF IC (IC5). The FM IF IC (IC5) contains a second mixer, a second local oscillator, second IF amplifiers, a second IF filter, an FM detector and a RSSI output. The signal applied to IC5 is mixed with 50.400MHz, which produces a 450kHz second IF signal. The signal obtained at the second mixer is filtered by a 450kHz ceramic filter (CF1 for wide or CF2 for narrow) and it is amplified by limiting amplifiers. The recovered audio signal from the incoming signal is obtained from quadrature type FM demodulator. This recovered audio signal is then sent to the audio amplifier circuit and to the noise actuated squelch circuit. The recovered audio signal obtained at IC5 is de-emphasized and further amplified for driving a loud speaker. 1.3 Transmitter Circuit The transmitter circuit consists of a microphone amplifier, an RF power amplifier driver (Q39, Q23, Q800 and Q801), an RF power amplifier (Q802), an antenna switching network, a spurious and harmonics low-pass filter, and an automatic power control (APC). The audio signal, originating at the microphone, is applied to the microphone amplifier (IC21, IC22). The audio signal is amplified, pre-emphasized (IC21, IC22), voltage limited and low-pass filtered. The signal is then switched by transistors to the TX VCO for modulating the transmit carrier signal. The transmit signal, generated at the frequency synthesizer, is applied to the RF power amplifier driver to gain a sufficient signal level to drive the RF power amplifier. The output signal from the RF power amplifier driver is further amplified, in the RF power amplifier, up to the level of the transmitter rated output power. This signal is routed to the antenna connector after going through the antenna switching network and the low-pass filter. This filter has a minimum attenuation of 65dB at the second harmonic frequency. This output power level once it was set it will be maintained at a constant output level by automatic power control unit (D805, D806, IC800). 1.4 Control Section The control section consists of a CPU (IC6), display unit and associated interface circuits. The CPU (IC6) is connected to an external EEPROM (IC7), which stores the operating frequency information. The CPU (IC6) performs the following functions: (1) Switches transmit and receive mode based on the push-to-talk line information at the Mic. connector (J1). (2) Detects control signals from key pad and converts the information to a serial format. (3) Retrieves the transmit and receive frequency programming data…

Text truncated - open the document above for the full version.

FCC ID:ALH32943220 TK-8102H(K2) Tuning Procedure 1-1 Tuning Procedure Before attempting to tune the transceiver, connect the unit to a suitable power supply. Whenever the transmitter tuned, must be connected to a suitable dummy load, unless the instructions specify otherwise. The speaker output connector must be terminated with a 4ohms dummy load at any time during the tuning and connected to an AC voltmeter and an audio distortion meter or a SINAD measurement meter at all the time during the tuning. Adjusting Mode Connect with the Radio and Personal Computer to COMPUTER PROGRAMMING INTERFACE (KPG-46) 1-2 Tuning Items Frequency Tune RF High Power RF Low Power DQT Balance (Wide/Narrow) Max Deviation (Wide/Narrow) QT Fine Deviation (Wide/Narrow) DQT Fine Deviation (Wide/Narrow) DTMF Fine Deviation (Wide/Narrow) Sensitivity (Wide) Squelch(Tight) (Wide/Narrow) Squelch(Open) (Wide/Narrow) 1-3 Test Mode Starting Test Mode, select the Tuning Frequency and Signaling. 1-3-1 Click the Program or press [Alt]+[P] to open the Program Menu of Window. 1-3-2 Click Test Mode or press [T] to Test Mode. 1-3-3 Open the Test Mode window after Tuning Data Read. : Combo Box 1-3-4 Click Combo box or use [Tab] keys to select channel combo box. Then click or use [↓][↑] keys to select channel number. 1-3-5 Click Combo box or use [Tab] keys to select Signaling combo box. FCC ID:ALH32943220 Then click or use [↓][↑] keys to select Signaling number. 1-3-6 Press the [Space] key or Click the [PTT] button on the Test Mode Window then Transmitter on. 1-3-7 Back to Reception during transmitter use [Space] keys or Click the [PTT] button. 2-1 Tuning Mode Starting Tuning Mode from Test Mode. 2-1-1 Click [Wide] button or use [Alt]+[w] keys to select Wide. 2-1-2 Click [Narrow] button or use Press [Alt]+[n] keys to select Narrow. 2-1-3 Click list box or use [Tab] key to select List box. Then Click or use [↓][↑] keys to select tuning item. Then Click the [Tuning Mode] button or use [Enter] key to go to Tuning Mode. : List Box 2-1-4 Open Tuning Mode window. : Slider 2-1-5 Press the [Space] key or Click the [PTT] button on the Test Mode Window then Transmitter on. 2-1-6 Back to Reception during transmitter use [Space] keys or Click the [PTT] button. 2-1-7 Click the Slider and use [←][→] keys to adjust the level then press [OK] button or press use [Alt]+[o] keys. 2-1-8 Click [Cancel] button or press use [Alt]+[c] keys to cancel the adjustment level. 2-1-9 Return to Test Mode Window. 2-1-10 Repeat from 2-1-1 to 2-1-9 to adjust each tuning item. 3-1 Ending Test Mode 3-1-1 Click the Exit button or press [Alt] +[x] on the test mode window to end test mode. FCC ID:ALH32943220 4-1 Tuning Frequencies Low RX : 485.05000, TX : 485.10000 Low’ RX : 491.80000, TX : 491.85000 Center RX : 498.55000, TX : 498.60000 High’ RX : 505.30000, TX : 505.35000 High RX : 511.95000, TX : 511.90000 Adjustment points 1point : Use Center frequency 3points : Use Low, Center and High frequencies 5points : Use Low, Low’, Center, High’ and High frequencies 5-1 VCO Alignment 5-1-1 Connect a voltmeter to CV 5-1-2 Set the frequency High 5-1-3 Adjust the voltage 5.5±0.2V (TX:TC2, RX:TC1) 5-2 Transmitter tuning 5-2-1 Select the tuning item “Frequency Tune”, set the frequency Center and transmit the radio, then adjust the frequency to 498.60000MHz ± 50Hz 5-2-2 Select the tuning item “RF High Power”, and transmit the radio. Then adjust the RF Power to 45 ± 1.0W. Adjustment point is 5. 5-2-3 Select the tuning item “RF Low Power”, and transmit the radio. Then adjust the RF Power to 25 ± 1.0 W. Adjustment point is 5. 5-2-4 Select the tuning item “DQT Balance(Wide)”, and transmit the radio. Then adjust the DQT waveform flat. Adjustment point is 3. 5-2-5 Select the tuning item “DQT Balance(Narrow)”, and transmit the radio. FCC ID:ALH32943220 Then adjust the DQT waveform flat. Adjustment point is 1. 5-2-6 Select the tuning item “Max Deviation(Wide)” and transmit the radio. Then adjust the Deviation 4.0 ± 0.1kHz. Adjustment point is 3. 5-2-7 Select the tuning item “Max Deviation(Narrow)” and transmit the radio. Then adjust the Deviation 2.0 ± 0.05kHz. Adjustment point is 1. 5-2-8 Select the tuning item “QT Fine Deviation(Wide)” and transmit the radio. Then adjust the Deviation 0.75 ± 0.05kHz. Adjustment point is 1. 5-2-9 Select the tuning item “QT Fine Deviation(Narrow)” and transmit the radio. Then adjust the Deviation 0.35 ± 0.05kHz. Adjustment point is 1. 5-2-10 Select the tuning item “DQT Fine Deviation(Wide)” and transmit the radio. Then adjust the Deviation 0.75 ± 0.05kHz. Adjustment point is 1. 5-2-11 Select the tuning item “DQT Fine Deviation(Narrow)” and transmit the radio. Then adjust the Deviation 0.35 ± 0.05kHz. Adjustment point is 1. 5-2-12 Select the tuning item “DTMF Fine Deviation(Wide)” and transmit the radio. Then adjust the Deviation 3.0 ± 0.2kHz. Adjustment point is 1. 5-2-13 Select the tuning item “DTMF Fine Deviation(Narrow)” and transmit the radio. Then adjust the Deviation 1.5 ± 0.1kHz. Adjustment point is 1. 5-3 Receiver tuning 5-3-1 Select the tuning item “Sensitivity”. Then adjust the receiver sensitivity maximum. Adjustment point is 3. 5-3-2 Select the tuning item “Squelch(Tight) (Wide)”. Then adjust the squelch(Tight) opening level –113dBm. Adjustment point is 1. 5-3-3 Select the tuning item “Squelch(Tight) (Narrow)”. Then adjust the squelch(Tight) opening level –112dBm. Adjustment point is 1. FCC ID:ALH32943220 5-3-4 Select the tuning item “Squelch(Open) (Wide)”. Then adjust the squelch(Open) opening level –120dBm. Adjustment point is 3. 5-3-5 Select the tuning item “Squelch(Open) (Narrow)”. Then adjust the squelch(Open) opening level –119dBm. Adjustment point is 1.

SEMICONDUCTOR DATA FOR FCC ID:ALH32943220 Model Name:TK-8102H(K2) Display Unit SYMBOL PARTS NUMBERPARTS NAMEDISCRIPTION D1B30-2238-05 LEDKEY BACKLIT D2B30-2238-05 LEDKEY BACKLIT D3B30-2238-05 LEDKEY BACKLIT D4B30-2238-05 LEDKEY BACKLIT D5B30-2239-05 LEDMONITOR KEY LIGHT D6B30-2239-05 LEDPROGRAMMABLE KEY LIGHT D7B30-2239-05 LEDCHANNEL KEY LIGHT D8B30-2239-05 LEDCHANNEL KEY LIGHT D9B30-2239-05 LEDCHANNEL KEY LIGHT D10B30-2239-05 LEDCHANNEL KEY LIGHT D11B30-2237-05 LEDBUSY KEY LIGHT D12B30-2240-05 LEDTRANSMIT KEY LIGHT Q1KRC102S TRANSISTORMONITOR KEY LIGHT SW Q2KRC102S TRANSISTORCHANNEL KEY LIGHT SW Q3KRC102S TRANSISTORCHANNEL KEY LIGHT SW Q4KRC102S TRANSISTORBUSY KEY LIGHT SW Q5KRC102S TRANSISTORPROGRAMMABLE KEY LIGHT SW Q6KRC102S TRANSISTORCHANNEL KEY LIGHT SW Q7KRC102S TRANSISTORCHANNEL KEY LIGHT SW Q8KRC102S TRANSISTORTRANSMIT KEY LIGHT SW Q9KRA225S TRANSISTORKEY BACKLIT SW Q10KRC102S TRANSISTORKEY BACKLIT SW SEMICONDUCTOR DATA FOR FCC ID:ALH32943220 Model Name:TK-8102H(K2) TX RX Unit SYMBOL PARTS NUMBERPARTS NAMEDISCRIPTION D1DA221 DIODESURGE ABSORPTION D2DA221 DIODESURGE ABSORPTION D3DA221 DIODESURGE ABSORPTION D4DA221 DIODESURGE ABSORPTION D6MA2S111 DIODEDC SWITCH D7HZU5ALL DIODEVOTAGE DROPPED D9MA2S304 VARICAPRX VCO D10MA2S304 VARICAPTX VCO D11MA2S304 VARICAPRX VCO D12MA2S304 VARICAPTX VCO D13DAN222 DIODEIF SWITCH (WIDE/NARROW) D14MA360 VARICAPMODULATION D15DAN222 DIODEIF SWITCH (WIDE/NARROW) D16MA2S111 DIODELIPPLE FILTER D18MA742 DIODERECTIFICATION D19DAN235E DIODERF SWITCH(TX/RX) D21HVC350B VARICAPRF BPF TUNING D22HVC350B VARICAPRF BPF TUNING D23DA221 DIODETEMPERATURE COMPENSATION D24MA742 DIODELIMITTER D25HVC350B VARICAPRF BPF TUNING D26HVC350B VARICAPRF BPF TUNING D28HVC350B VARICAPRF BPF TUNING D38ZSH5MA27 DIODEREVERSE CONNECT PROTECTION D3902DZ18(X,Y) DIODEOVER VOLTAGE DETECTION D411812L110PR POLY SWCURRENT PROTECTION D43DAN222 DIODEOR GATE D441SS372 DIODEAGC D80002DZ5.1(Y) DIODEVOLTAGE PROTECTION D801MA4PH633 DIODEANT SW D802MA4PH633 DIODEANT SW D803XB15A709 DIODEANT SW D804XB15A709 DIODEANT SW D805MA742 DIODEAPC VOLTAGE DETECT D806MA742 DIODEAPC VOLTAGE DETECT D8071SS355 DIODETEMPERATURE COMPENSATION Q22SJ243 FETMIC MUTE Q32SC4649(N,P) TRANSISTORRF AMP Q42SA1832(GR) TRANSISTORCHARGE PUMP Q52SC4738(GR) TRANSISTORCHARGE PUMP Q62SC4649(N,P) TRANSISTORBUFFER AMP Q72SJ243 FETT/R SW Q102SK508NV(K52) FETRX VCO Q112SK508NV(K52) FETTX VCO Q12KRX102U TRANSISTORT/R SW Q132SK1824 TRANSISTORBEAT SHIFT Q142SC4617(S) TRANSISTORLIPPLE FILTER Q152SC5108(Y) TRANSISTORBUFFER AMP Q16KRC414RTK TRANSISTORIGNITION Q182SC2412K TRANSISTORSQL AMP Q192SC4649(N,P) TRANSISTORIF AMP Q202SC5108(Y) TRANSISTORRF AMP Q213SK255 FETMIXER Q222SK1824 FETAF MUTE Q232SC3356(R24) TRANSISTORRF AMP Q242SC4617(S) TRANSISTORBUFFER AMP Q263SK255 FETRF AMP Q29KRC102S TRANSISTORDC SWITCH(8R) Q30KRC102S TRANSISTORDC SWITCH(8T) Q312SA1745(6,7) TRANSISTORDC SWITCH(8R) Q32DTC363EU TRANSISTORAF MUTE Q33KTA1664(Y) TRANSISTORDC SWITCH(8T) Q34KRC102S TRANSISTORDC SWITCH(SB) Q35KRC102S TRANSISTORAF MUTE Q372SK1824 TRANSISTORBEAT SHIFT Q38KRC404RTK TRANSISTOROVER VOLTAGE DETECTION Q392SC5110(O) TRANSISTORRF AMP Q412SC4919 TRANSISTORAF AMP Q422SA1641(S,T) TRANSISTORDC SWITCH(SB) Q432SK1824 FETAF MUTE Q1012SK3478-22 FETFINAL AMP Q8002SK2596 TRANSISTORDRIVE1 Q8012SK3075 FETDRIVE2 IC1MB15A02 ICPLL SYNTHESIZER IC3M62363FP ICDIGITAL POTENTIOMETER IC4NJM2902V ICBUFFER AMP IC5TK14489V ICFM DEMODULATION IC6784214AGC125 ICCPU IC724LC08BT-ISN ICEEPROM IC9LC73872M ICDTMF DECODE IC10NJM2902V ICAudio Filter IC11NJM2904V ICActive Filter (QT/DQT) IC14NJM78L05UA ICVoltage regulator (5C) IC15PST9140NR ICVotage detector Reset IC17NJM78L05UA ICVoltage regulator (5M) IC18PST9140NR ICVotage detector Int IC19TC7W74FU ICDIVIDER (7.159MHz) IC20KIA7808AF ICVoltage regulator (8C) IC21NJM2100V ICMIC AMP IC22NJM2904V ICMIC AMP IC101LA4600 ICAF AMP IC800TA75W01FU ICAPC CONTROL

FCC ID:ALH32943220 Model Name:TK-8102HK2 ＫＥＴＳ K2 部品番号'0-12単位 英語品名 PARTNO'0-12UNIT PART NAME(E) Z83-3166-03X1 INTERCONNECTION DIAGRAM X54-3340-2011 DISPLAY UNIT X57-6390-221 TX-RX UNIT X57-6390-2111 TX-RX UNIT A01-2181-0111 CABINET A10-4048-1111 CHASSIS A62-0942-0311 PANEL ASS'Y B10-2668-0311 FRONT GLASS B41-1837-0411 CAUTION LABEL B42-5650-0411 S/NO. LABEL B44-2163-0411 UPC CODE LABEL B44-2165-040.25 UPC CODE LABEL B46-0470-0011 WARRANTY CARD B59-1653-0011 PAMPHLET B62-1596-0011 INSTRUCTION MANUAL B62-1597-0011 INSTRUCTION MANUAL B72-2042-041 MODEL NAME PLATE B72-2041-0411 MODEL NAME PLATE E04-0167-0511 RF COAXIAL PECEPTACLE(M) E30-3339-0511 DC CORD E30-3448-0511 DC CORD E37-0961-0511 FLAT CABLE E37-0962-0511 LEAD WIRE WITH CONNECTOR F01-1024-1411 RADIATION PLATE F10-2421-0111 SHIELDING COVER F51-0017-0521 FUSE(6*30) G11-4127-1421 RUBBER SHEET G13-1468-0411 CUSHION G13-1836-0411 CUSHION G53-1525-0311 PACKING G53-1542-0311 PACKING G53-1544-0111 PACKING G53-1548-0211 GASKET H12-3112-0521 PACKING FIXTURE H13-1190-0211 CARTON BOARD H25-2341-0421 PROTECTION BAG H52-1829-1211 ITEM CARTON CASE H62-1581-030.25 OUTER PACKING CASE J19-1584-0511 HOLDER J29-0662-0311 BRACKET K29-9065-0111 KEY TOP N87-2606-46141 BRAZIER HEAD TAPTITE SCREW N87-2614-4681 BRAZIER HEAD TAPTITE SCREW N99-0395-0511 SCREW SET T07-0739-0511 SPEAKER T91-0624-0511 MICROPHONE CM73F2H300J21 MICA CAP LA460011 BI-POLAR IC N67-2608-4631 PAN HEAD SEMS SCREW W 2SK3478-2211 FET F53-0108-0511 FUSE C93-0562-0511 CERAMIC CAP

-t -t -t -t -t -t 1 DATE ISSUED REVISION NO 32 USE FOR 415 SYMBOL 2 3 4 5 6 7 8 9 1011 121314 15 16 ABCDEFGHIJ 679 8 PART NUM…

Text truncated - open the document above for the full version.